Ni-La2O3/CeO2 composite films were prepared by electrodeposition from a nickel sulfate bath containing certain content of micrometer and nanometer La2O3/CeO2 particles. The effect of La2O3 or CeO2 particle size on the...Ni-La2O3/CeO2 composite films were prepared by electrodeposition from a nickel sulfate bath containing certain content of micrometer and nanometer La2O3/CeO2 particles. The effect of La2O3 or CeO2 particle size on the oxidation resistance of the electrodeposited Ni-La2O3/CeO2 composites in air at 1000 °C was studied. The results indicate that, compared with the electrodeposited Ni-film, Ni-La2O3/CeO2 composites exhibit a superior oxidation resistance due to the codeposited La2O3 or CeO2 particles blocking the outward diffusion of nickel. Moreover, compared with nanoparticles, La2O3 or CeO2 microparticles have stronger effect because La2O3 or CeO2 microparticles also act as a diffusion barrier layer at the onset of oxidation.展开更多
Three different chromizing coatings were produced on Ni substrate using a conventional pack-cementation method with Al2O3,Al2O3＋CeO2 and CeO2 acting as filler,respectively,at a greatly decreased temperature（700 ℃）...Three different chromizing coatings were produced on Ni substrate using a conventional pack-cementation method with Al2O3,Al2O3＋CeO2 and CeO2 acting as filler,respectively,at a greatly decreased temperature（700 ℃）.Effects of different fillers on the isothermal and cyclic oxidation resistance of chromizing coating in air at 850 ℃ were comparably investigated.Microstructure results show that the addition of CeO2 into the filler significantly retards the grain growth of the chromizing coating.Oxidation results indicate that the chromizing coating using CeO2 as filler exhibits somewhat increased oxidation resistance than the normal chromizmg coating,while the chromizing coating using Al2O3＋CeO2 as filler exhibits much better oxidation resistance.The effects of different fillers on the oxidation behaviors were discussed in detail.展开更多
Ni3Al coatings with and without Y2O3 particles were developed by annealing the electrodeposited Ni-Al composite coatings with and without Y2O3 particles at 800 °C for 3 h. The microstructures and cyclic oxidation...Ni3Al coatings with and without Y2O3 particles were developed by annealing the electrodeposited Ni-Al composite coatings with and without Y2O3 particles at 800 °C for 3 h. The microstructures and cyclic oxidation performances of the produced Ni3Al coatings were comparatively investigated, with the emphasis on the effect of Y2O3. SEM/EDAX and TEM characterizations showed that the dispersion of Y2O3 refines the grains. Oxidation at 900 °C for 100 h showed that the addition of Y2O3 significantly improved the cyclic oxidation resistance of Ni3Al coating. The effect of Y2O3 on the microstructure and the oxidation of the Ni3Al coating were discussed in detail.展开更多
By using CeO2 particles instead of part of Al2O3 particles as filler, the CeO2 was successfully entrapped into the outer layer of the chromizing coatings on the as-deposited nanocrystalline （NC） and microcrystalline...By using CeO2 particles instead of part of Al2O3 particles as filler, the CeO2 was successfully entrapped into the outer layer of the chromizing coatings on the as-deposited nanocrystalline （NC） and microcrystalline （MC） Ni films using a conventional pack-cementation method at 800 °C. For comparison, chromizing was also performed under the same condition on MC Ni film using Al2O3 as filler without CeO2 particles. SEM/EDX and TEM results indicate that the refinement of Ni grain and CeO2 entrapped into the chromizing coatings refine the grain of the chromizing coating. Oxidation at 900 °C indicates that compared with the CeO2-free chromizing coating, the CeO2-dispersed chromizing coating exhibits an increased oxidation resistance. For the CeO2-dispersed chromizing coating, the refinement of Ni grain size significantly decreases the transient-oxidation scaling rate of the chromizing coatings. Together with this, the CeO2-dispersed chromizing coating formed on NC Ni exhibits a better oxidation resistance.展开更多
Oxide pegging is a widely accepted mechanistic model explaining the reactive element effect on the improved adherence of scale.However,previous models for the oxide peg formation process have not considered the effect...Oxide pegging is a widely accepted mechanistic model explaining the reactive element effect on the improved adherence of scale.However,previous models for the oxide peg formation process have not considered the effects of more than one active element added into the alloy during the peg formation.This study proposes a new model of oxide peg formation and growth for the doping of two reactive elements in an alloy(the precipitated Y and solid solute Ti).Different amounts of Ti and Y were added to a Co Ni Cr Al alloy,and the characteristics of the resulting oxide pegs,such as their linear density,size,and forming process,are obtained by examining alloy samples subjected to an isothermal oxidation operation at a temperature of 1150℃.It is found that the amount of Y determines the density of the oxide pegs,and Ti does not form a Ti-rich oxide core if a Y-rich oxide exists in the sample.In samples with the same Y content,the oxide pegs primarily grow in length,and with increased Ti content,they grow along the b-phase boundary and into the alloy.Based on these results,a three-step model for oxide peg formation and growth is conceived.展开更多
基金Project(GC13A113)supported by the Technology Research and Development Program of Heilongjiang Provincial Science and Technology DepartmentProject(12511469)supported by Heilongjiang Provincial Science and Technology Department
文摘Ni-La2O3/CeO2 composite films were prepared by electrodeposition from a nickel sulfate bath containing certain content of micrometer and nanometer La2O3/CeO2 particles. The effect of La2O3 or CeO2 particle size on the oxidation resistance of the electrodeposited Ni-La2O3/CeO2 composites in air at 1000 °C was studied. The results indicate that, compared with the electrodeposited Ni-film, Ni-La2O3/CeO2 composites exhibit a superior oxidation resistance due to the codeposited La2O3 or CeO2 particles blocking the outward diffusion of nickel. Moreover, compared with nanoparticles, La2O3 or CeO2 microparticles have stronger effect because La2O3 or CeO2 microparticles also act as a diffusion barrier layer at the onset of oxidation.
基金Project (11551419) supported by Scientific Research Fund of Heilongjiang Provincial Education DepartmentProject (12511469) supported by Heilongjiang Provincial Science and Technology Department
文摘Three different chromizing coatings were produced on Ni substrate using a conventional pack-cementation method with Al2O3,Al2O3＋CeO2 and CeO2 acting as filler,respectively,at a greatly decreased temperature（700 ℃）.Effects of different fillers on the isothermal and cyclic oxidation resistance of chromizing coating in air at 850 ℃ were comparably investigated.Microstructure results show that the addition of CeO2 into the filler significantly retards the grain growth of the chromizing coating.Oxidation results indicate that the chromizing coating using CeO2 as filler exhibits somewhat increased oxidation resistance than the normal chromizmg coating,while the chromizing coating using Al2O3＋CeO2 as filler exhibits much better oxidation resistance.The effects of different fillers on the oxidation behaviors were discussed in detail.
基金Project (11531319) supported by Scientific Research Fund of Heilongjiang Provincial Education Department, China
文摘Ni3Al coatings with and without Y2O3 particles were developed by annealing the electrodeposited Ni-Al composite coatings with and without Y2O3 particles at 800 °C for 3 h. The microstructures and cyclic oxidation performances of the produced Ni3Al coatings were comparatively investigated, with the emphasis on the effect of Y2O3. SEM/EDAX and TEM characterizations showed that the dispersion of Y2O3 refines the grains. Oxidation at 900 °C for 100 h showed that the addition of Y2O3 significantly improved the cyclic oxidation resistance of Ni3Al coating. The effect of Y2O3 on the microstructure and the oxidation of the Ni3Al coating were discussed in detail.
基金Project(11531319)supported by Scientific Research Fund of Heilongjiang Provincial Education Department,China
文摘By using CeO2 particles instead of part of Al2O3 particles as filler, the CeO2 was successfully entrapped into the outer layer of the chromizing coatings on the as-deposited nanocrystalline （NC） and microcrystalline （MC） Ni films using a conventional pack-cementation method at 800 °C. For comparison, chromizing was also performed under the same condition on MC Ni film using Al2O3 as filler without CeO2 particles. SEM/EDX and TEM results indicate that the refinement of Ni grain and CeO2 entrapped into the chromizing coatings refine the grain of the chromizing coating. Oxidation at 900 °C indicates that compared with the CeO2-free chromizing coating, the CeO2-dispersed chromizing coating exhibits an increased oxidation resistance. For the CeO2-dispersed chromizing coating, the refinement of Ni grain size significantly decreases the transient-oxidation scaling rate of the chromizing coatings. Together with this, the CeO2-dispersed chromizing coating formed on NC Ni exhibits a better oxidation resistance.
基金financially supported by Tsinghua University Initiative Scientific Research Program and the National Magnetic Confinement Fusion Energy Research Project of China(No.2015GB118001)。
文摘Oxide pegging is a widely accepted mechanistic model explaining the reactive element effect on the improved adherence of scale.However,previous models for the oxide peg formation process have not considered the effects of more than one active element added into the alloy during the peg formation.This study proposes a new model of oxide peg formation and growth for the doping of two reactive elements in an alloy(the precipitated Y and solid solute Ti).Different amounts of Ti and Y were added to a Co Ni Cr Al alloy,and the characteristics of the resulting oxide pegs,such as their linear density,size,and forming process,are obtained by examining alloy samples subjected to an isothermal oxidation operation at a temperature of 1150℃.It is found that the amount of Y determines the density of the oxide pegs,and Ti does not form a Ti-rich oxide core if a Y-rich oxide exists in the sample.In samples with the same Y content,the oxide pegs primarily grow in length,and with increased Ti content,they grow along the b-phase boundary and into the alloy.Based on these results,a three-step model for oxide peg formation and growth is conceived.
