Thermal Error Compensation of the Wear-Depth Real-Time Detecting of Self-Lubricating Spherical Plain Bearings

The spherical plain bearing test bench is a necessary detecting equipment in the research process of self?lubricating spherical plain bearings. The varying environmental temperatures cause the thermal deformation of the wear?depth detecting system of bearing test benches and then a ect the accuracy of the wear?depth detecting data. However, few researches about the spherical plain bearing test benches can be found with the implementation of the detect?ing error compensation. Based on the self?made modular spherical plain bearing test bench, two main causes of ther?mal errors, the friction heat of bearings and the environmental temperature variation, are analysed. The thermal errors caused by the friction heat of bearings are calculated, and the thermal deformation of the wear?depth detecting sys?tem caused by the varying environmental temperatures is detected. In view of the above results, the environmental temperature variation is the main cause of the two error factors. When the environmental temperatures rise is 10.3 °C, the thermal deformation is approximately 0.01 mm. In addition, the comprehensive compensating model of the thermal error of the wear?depth detecting system is built by multiple linear regression(MLR) and time series analysis. Compared with the detecting data of the thermal errors, the comprehensive compensating model has higher fitting precision, and the maximum residual is only 1 μm. A comprehensive compensating model of the thermal error of the wear?depth detecting system is proposed, which provides a theoretical basis for the improvement of the real?time wear?depth detecting precision of the spherical plain bearing test bench.

Real-Time Iterative Compensation Framework for Precision Mechatronic Motion Control Systems

With regard to precision/ultra-precision motion systems,it is important to achieve excellent tracking performance for various trajectory tracking tasks even under uncertain external disturbances.In this paper,to overcome the limitation of robustness to trajectory variations and external disturbances in offline feedforward compensation strategies such as iterative learning control(ILC),a novel real-time iterative compensation(RIC)control framework is proposed for precision motion systems without changing the inner closed-loop controller.Specifically,the RIC method can be divided into two parts,i.e.,accurate model prediction and real-time iterative compensation.An accurate prediction model considering lumped disturbances is firstly established to predict tracking errors at future sampling times.In light of predicted errors,a feedforward compensation term is developed to modify the following reference trajectory by real-time iterative calculation.Both the prediction and compen-sation processes are finished in a real-time motion control sampling period.The stability and convergence of the entire control system after real-time iterative compensation is analyzed for different conditions.Various simulation results consistently demonstrate that the proposed RIC framework possesses satisfactory dynamic regulation capability,which contributes to high tracking accuracy comparable to ILC or even better and strong robustness.

Comparison of delay compensation methods for real-time hybrid simulation using frequency-domain evaluation index

The delay compensation method plays an essential role in maintaining the stability and achieving accurate real-time hybrid simulation results. The effectiveness of various compensation methods in different test scenarios, however, needs to be quantitatively evaluated. In this study, four compensation methods （i.e., the polynomial extrapolation, the linear acceleration extrapolation, the inverse compensation and the adaptive inverse compensation） are selected and compared experimentally using a frequency evaluation index （FEI） method. The effectiveness of the FEI method is first verified through comparison with the discrete transfer fimction approach for compensation methods assuming constant delay. Incomparable advantage is further demonstrated for the FEI method when applied to adaptive compensation methods, where the discrete transfer function approach is difficult to implement. Both numerical simulation and laboratory tests with predefined displacements are conducted using sinusoidal signals and random signals as inputs. Findings from numerical simulation and experimental results demonstrate that the FEI method is an efficient and effective approach to compare the performance of different compensation methods, especially for those requiring adaptation of compensation parameters.

Research on dynamic error compensation for an armored K type thermocouple

A new method was proposed, in which a high-power CO2 laser modulated by high frequency was used as the driv- ing source to heat up a surface-temperature sensor. The continual beam and the pulsed beam sent out by the same laser could be used in the same system to carry on the static calibration of the radiation thermometer and the dynamic calibration of the temperature sensor to be checked. The frequency-response characteristics of high-speed radiation thermometer surpassed that of the temperature sensor, therefore it could be used as the reference value to calibrate the latter and let system error be cor- rected. Differences in the environment of the sensor installing and the error caused by the change of thermo-physical proper- ty could be avoided. Thus, the difficult problem of traceable dynamic calibration of temperature was solved. In experiment, to obtain the frequency characteristics of the thermocouple and the dynamic performance of the K type thermocouple, which could compensate the dynamic characteristics of the sensor, the sensor was dynamically corrected by using the method, and then the mathematical model was established.

Research on the Dynamic Model of Spindle Rotation Induced Error Compensation System of Boring and its Simulation

In this paper we address the dynamics of compensation cutting process from both Laplace s frequency domain and the time domain of the first time, using the two computer aided analyzing softwares: MATLAB and SIMULINK. Theoretical analysis and simulation experiments firstly show that not only the systematical stiffness of workpiece, spindle and tools, but also the regenerated coefficient affects the compensation displacement effect. The results show that the SREC is practicable in reality to decease the spindle induced errors in many engineering applications such as hard boring through simulation and the preliminary experiment results.

MODELING AND COMPENSATION TECHNIQUE FOR THE GEOMETRIC ERRORS OF FIVE-AXIS CNC MACHINE TOOLS

One of the important trends in precision machining is the development ofreal-time error compensation technique. The error compensation for multi-axis CNC machine tools isvery difficult and attractive. The modeling for the geometric error of five-axis CNC machine toolsbased on multi-body systems is proposed. And the key technique of the compensation―identifyinggeometric error parameters―is developed. The simulation of cutting workpiece to verify the modelingbased on the multi-body systems is also considered.

Periodic Error Compensation for Quartz MEMS Gyroscope Drift of INS

In order to improve the navigation accuracy of an inertial navigation system （INS）, composed of quartz gyroscopes, the existing real-time compensation methods for periodic errors in quartz gyroscope drift and the periodic error term relationship between sampled original data and smoothed data are reviewed. On the base of the results, a new compensation method called using former period characteristics to compensate latter smoothness data （UFCL for short） method is proposed considering the INS working characteristics. This new method uses the original data without smoothing to work out an error conversion formula at the INS initial alignment time and then compensate the smoothed data errors by way of the formula at the navigation time. Both theoretical analysis and experimental results demonstrate that this method is able to cut down on computational time and raise the accuracy which makes it a better real-time compensation approach for periodic error terms of quartz micro electronic mechanical system （MEMS） gyroscope＇s zero drift.

Error Compensation of Thin Plate-shape Part with Prebending Method in Face Milling

Low weight and good toughness thin plate parts are widely used in modem industry, but its flexibility seriously impacts the machinability. Plenty of studies locus on the influence of machine tool and cutting tool on the machining errors. However, few researches focus on compensating machining errors through the fixture. In order to improve the machining accuracy of thin plate-shape part in face milling, this paper presents a novel method for compensating the surfacc errors by prebending the workpiece during the milling process. First, a machining error prediction model using finite element method is formulated, which simplifies the contacts between the workpiece and fixture with spring constraints. Milling fbrces calculated by the micro-unit cutting force model arc loaded on the error prediction model to predict the machining error. The error prediction results are substituted into the given formulas to obtain the prebending clamping forces and clamping positions. Consequently, the workpiece is prebent in terms of the calculated clamping forces and positions during the face milling operation to reduce the machining error. Finally, simulation and experimental tests are carried out to validate the correctness and efficiency of the proposed error compensation method. The experimental measured flatness results show that the flatness improves by approximately 30 percent through this error compensation method. The proposed mcthod not only predicts the machining errors in face milling thin plate-shape parts but also reduces the machining errors by taking full advantage of the workpiece prebending caused by fixture, meanwhile, it provides a novel idea and theoretical basis for reducing milling errors and improving the milling accuracy.

Modeling and Compensation Technology for the Comprehensive Errors of Fixture System

Error modelling and compensating technology is an effective method to improve the processing precision.The position and orientation deviation of workpiece is caused by the fixing and manufacturing errors of the fixture.How to reduce the position and orientation deviation of workpiece has become a technical problem of improving the processing quality of workpiece.In order to increase machining accuracy,an implementation scheme of fixture system comprehensive errors（FSCE） compensation is proposed.A FSCE parameter model is established by analyzing the influence of contact points on the position and orientation of workpiece.Meanwhile,a parameter identification method for FSCE parameter model is presented by using the 3-2-1 deterministic positioning fixture,which determines the model parameters.Moreover,a FSCE compensation model is formulated to study the compensation value of the cutting position.By using RenishawOMP60 Probe and combining vertical machining centre（SKVH850） equipment with SKY2001 Open CNC System,on-machine verification system（OMVS） is built to measure FSCE successfully.The processing error can be reduced by analyzing the cutting position of the tool with the homogeneous transformation of space coordinate system.Finally,the compensation experiment of real time errors is conducted,and the cylindricality and perpendicularity errors of hole surface are reduced by 30.77% and 28.57%,respectively.This paper provides a new way of realizing the compensation of FCSE,which can improve the machining accuracy of workpiece largely.

Motion Error Compensation of Multi-legged Walking Robots

Existing errors in the structure and kinematic parameters of multi-legged walking robots,the motion trajectory of robot will diverge from the ideal sports requirements in movement.Since the existing error compensation is usually used for control compensation of manipulator arm,the error compensation of multi-legged robots has seldom been explored.In order to reduce the kinematic error of robots,a motion error compensation method based on the feedforward for multi-legged mobile robots is proposed to improve motion precision of a mobile robot.The locus error of a robot body is measured,when robot moves along a given track.Error of driven joint variables is obtained by error calculation model in terms of the locus error of robot body.Error value is used to compensate driven joint variables and modify control model of robot,which can drive the robots following control model modified.The model of the relation between robot＇s locus errors and kinematic variables errors is set up to achieve the kinematic error compensation.On the basis of the inverse kinematics of a multi-legged walking robot,the relation between error of the motion trajectory and driven joint variables of robots is discussed.Moreover,the equation set is obtained,which expresses relation among error of driven joint variables,structure parameters and error of robot＇s locus.Take MiniQuad as an example,when the robot MiniQuad moves following beeline tread,motion error compensation is studied.The actual locus errors of the robot body are measured before and after compensation in the test.According to the test,variations of the actual coordinate value of the robot centroid in x-direction and z-direction are reduced more than one time.The kinematic errors of robot body are reduced effectively by the use of the motion error compensation method based on the feedforward.

Kinematic Calibration and Forecast Error Compensation of a 2-DOF Planar Parallel Manipulator

Due to large workspace,heavy-duty and over-constrained mechanism,a small deformation is caused and the precision of the 2-DOF planar parallel manipulator is affected.The kinematic calibration cannot compensate the end-effector errors caused by the small deformation.This paper presents a method combined step kinematic calibration and linear forecast real-time error compensation in order to enhance the precision of a two degree-of-freedom(DOF) planar parallel manipulator of a hybrid machine tool.In the step kinematic calibration phase of the method,the end-effector errors caused by the errors of major constant geometrical parameters is compensated.The step kinematic calibration is based on the minimal linear combinations(MLCs) of the error parameters.All simple and feasible measurements in practice are given,and identification analysis of the set of the MLCs for each measurement is carried out.According to identification analysis results,both measurement costs and observability are considered,and a step calibration including step measurement,step identification and step error compensation is determined.The linear forecast real-time error compensation is used to compensate the end-effector errors caused by other parameters after the step kinematic calibration.Taking the advantages of the step kinematic calibration and the linear forecast real-time error compensation,a method for improving the precision of the 2-DOF planar parallel manipulator is developed.Experiment results show that the proposed method is robust and effective,so that the position errors are kept to the same order of the measurement noise.The presented method is attractive for the 2-DOF planar parallel manipulator and can be also applied to other parallel manipulators with fewer than six DOFs.

QFT control based on zero phase error compensation for flight simulator

To improve the robustness of high-precision servo systems, quantitative feedback theory （QFT） which aims to achieve a desired robust design over a specified region of plant uncertainty is proposed. The robust design problem can be solved using QFT but it fails to guarantee a high precision tracking. This problem is solved by a robust digital QFT control scheme based on zero phase error （ZPE） feed forward compensation. This scheme consists of two parts： a QFT controller in the closed-loop system and a ZPE feed-forward compensator. Digital QFT controller is designed to overcome the uncertainties in the system. Digital ZPE feed forward controller is used to improve the tracking precision. Simulation and real-time examples for flight simulator servo system indicate that this control scheme can guarantee both high robust performance and high position tracking precision.

Self-calibration and Compensation of Setting Errors for Surface Profile Measurement of a Microstructured Roll Workpiece

Microstructured roll workpieces have been widely used as functional components in the precision industries. Current researches on quality control have focused on surface profile measurement of microstructured roll workpieces, and types of measurement systems and measurement methods have been developed. However, low measurement efficiency and low measurement accuracy caused by setting errors are the common disadvantages for surface profile measurement of microstructured roll workpieces. In order to shorten the measurement time and enhance the measurement accuracy, a method for self-calibration and compensation of setting errors is proposed for surface profile measurement of microstructured roll workpieces. A measurement system is constructed for the measurement, in which a precision spindle is employed to rotate the roll workpiece and an air-bearing displacement sensor with a micro-stylus probe is employed to scan the microstructured surface of the roll workpiece. The resolution of the displacement sensor is 0.14 nm and that of the rotary encoder of the spindle was 0.15r~. Geometrical and mathematical models are established for analyzing the influences of the setting errors of the roll workpiece and the displacement sensor with respect to the axis of the spindle, including the eccentric error of the roll workpiece, the offset error of the sensor axis and the zero point error of the sensor output. Measurement experiments are carded out on a roll workpiece on which periodic microstructures are a period of 133 i^m along the circumferential direction. Experimental results demonstrate the feasibility of the self-compensation method. The proposed method can be used to detect and compensate the setting errors without using any additional accurate artifact.

Thermal Error Compensation for Telescopic Spindle of CNC Machine Tool Based on SIEMENS 840D System

In this paper, eddy current sensors and thermocouple sensors were employed to measure the thermal field and thermal deformation of a spindle of a telescopic CNC boring-milling machine tool, respectively. A linear regression method was proposed to establish the thermal error model. Furthermore, two compensation methods were implemented based on the SIEMENS 840D system by using the feed shaft of z direction and telescopic spindle respectively. Experimental results showed that the thermal error could be reduced by 73.79% when using the second compensation method, and the thermal error could be eliminated by using the two compensation methods effectively.

ROBOT'S MOTION ERROR AND ONLINE COMPENSATION BASED ON FORCE SENSOR

Robot＇s dynamic motion error and on-line compensation based on multi-axis force sensor are dealt with.It is revealed that the reasons of the error are formed and the relations of the error are delivered.A motion equation of robot＇s termination with the error is established,and then,an error matrix and an error compensation matrix of the motion equation are also defined.An on-line error＇s compensation method is put forward to decrease the displacement error,which is a degree of millimeter,shown by the result of simulation of PUMA562 robot.

Modeling Approach of Regression Orthogonal Experiment Design for Thermal Error Compensation of CNC Turning Center

The thermal induced errors can account for as much as 70% of the dimensional errors on a workpiece. Accurate modeling of errors is an essential part of error compensation. Base on analyzing the existing approaches of the thermal error modeling for machine tools, a new approach of regression orthogonal design is proposed, which combines the statistic theory with machine structures, surrounding condition, engineering judgements, and experience in modeling. A whole computation and analysis procedure is given. Therefore, the model got from this method are more robust and practical than those got from the present method that depends on the modeling data completely. At last more than 100 applications of CNC turning center with only one thermal error model are given. The cutting diameter variation reduces from more than 35 μm to about 12 μm with the orthogonal regression modeling and compensation of thermal error.

Improved High Order Model-Free Adaptive Iterative Learning Control with Disturbance Compensation and Enhanced Convergence

In this paper,an improved high-order model-free adaptive iterative control(IHOMFAILC)method for a class of nonlinear discrete-time systems is proposed based on the compact format dynamic linearization method.This method adds the differential of tracking error in the criteria function to compensate for the effect of the random disturbance.Meanwhile,a high-order estimation algorithmis used to estimate the value of pseudo partial derivative(PPD),that is,the current value of PPD is updated by that of previous iterations.Thus the rapid convergence of the maximumtracking error is not limited by the initial value of PPD.The convergence of the maximumtracking error is deduced in detail.This method can track the desired output with enhanced convergence and improved tracking performance.Two examples are used to verify the convergence and effectiveness of the proposed method.

Prediction of diameter errors compensation in bars turning

On the basis of analyzing the machine-workpiece-tool system, the main factors affecting diameter errors in bars turning are considered, and the mathematic models of the actual workpiece diameter at the cutting point are established according to the three usual methods of mounting workpieces on a turning machine. Further a prediction system for diameter errors is developed; a new method, called discrete nodes output, is presented and applied to expressing workpiece diameter errors at given points along the part axis, then off-line compensation is implemented according to the prediction values to diminish machining errors. The results indicate that the method can diminish diameter errors more than 70%, greatly improve the machining accuracy of bars.

A convenient look-up-table based method for the compensation of non-linear error in digital fringe projection

Although the structured light system that uses digital fringe projection has been widely implemented in three-dimensional surface profile measurement, the measurement system is susceptible to non-linear error. In this work, we propose a convenient look-up-table-based （LUT-based） method to compensate for the non-linear error in captured fringe patterns. Without extra calibration, this LUT-based method completely utilizes the captured fringe pattern by recording the full-field differences. Then, a phase compensation map is established to revise the measured phase. Experimental results demonstrate that this method works effectively.

Non-Exchangeable Error Compensation for Strapdown Inertial Navigation System in High Dynamic Environment

Strapdown non-exchangeable error compensation technology in high dynamic environment is one of the key technologies of strapdown inertial navigation system.Mathematical platform is used in strapdown inertial navigation system instead of physical platform in traditional platform inertial navigation system,which improves reliability and reduces cost and volume of system.The maximum error source of attitude matrix solution is the non-exchangeable error of rotation due to the non-exchangeable of finite rotation of rigid bodies.The rotation non-exchangeable error reaches the maximum in coning motion,although it can be reduced by shortening the correction period and increasing the real-time calculation.The equivalent rotation vector method is used to modify the attitude to reduce the coning error in this paper.Simulation experiments show that the equivalent rotation vector method can effectively suppress the non-exchangeable error and improve the accuracy of attitude calculation.