High Sensitivity Digital Instantaneous Frequency Measurement Receiver for Precise Frequency Analysis

There are numerous applications, such as Radar, that leverage wideband technology. However, the presence of noise introduces certain limitations and challenges. It is crucial to harness wideband technology for applications demanding the rapid and precise transmission of diverse information from one point to another within a short timeframe. The ability to report a signal without tuning within the input bandwidth stands out as one of the advantages of employing a digital wideband receiver. As indicated, a digital wideband receiver plays a pivotal role in achieving high precision and accuracy. The primary distinction between Analog and Digital Instantaneous Frequency Measurement lies in the fact that analog Instantaneous Frequency Measurement (IFM) receivers have traditionally covered extensive input bandwidths, reporting one accurate frequency per short pulse. In the contemporary landscape, digital IFM systems utilize high-sampling-rate Analog-to-Digital Converters (ADC) along with Hilbert transforms to generate two output channels featuring a 90-degree phase shift. This paper explores the improvement of sensitivity in current digital IFM receivers. The optimization efforts target the Hilbert transform and autocorrelations architectures, aiming to refine the system’s ability to report fine frequencies within a noisy wide bandwidth environment, thereby elevating its overall sensitivity.

Research for the Dynamic Range and Its Extension of Digital Intermediate Frequency Receiver

For the optimization of dynamic range and bandwidth of digital intermediate frequency receiver(DIFR), main factors affecting them and their relationships are studied. Firstly, the DIFR sensitivity, bandwidth, noise factor of radio frequency (RF) analog front-end (RFAF), and processing gain of intermediate frequency(IF) sampling are analyzed. Secondly, the constraint relationship of the noise factor of RFAF, the signal-to-noise ratio of ADC and the dynamic range of DIFR are studied. The relationship between the dynamic range and the RFAF gain, and that of the extended dynamic range and the RF AGC(automatic gain control) step are educed and simulated. These results can be used as theory foundations and design references for the implementation and optimization of the large dynamic range and wideband DIFR.

Robust digital receiver for EPC sensor network

A robust digital receiver based on a matched filter （MF） is proposed for the radio frequency identification （RFID） reader system to enhance the reliability of signal processing in the electronic product code （EPC） sensor network （ESN）. The performance of the proposed receiver is investigated by examining the anti-collision algorithm in the EPC global Class1 Generation2 protocol. The validity and usefulness are demonstrated by both computer simulations and experiments. Based on the verification results, comparing with the conventional zero crossing detector （ZCD） based receiver, the proposed receiver is very robust against strong amplitude distortions and considerable frequency deviations happening on the backscattered signal from a passive tag.

Frequency Structures Vibration Identified by an Adaptative Filtering Techiques Applied on GPS L1 Signal

This paper is part of a research under enhancement since 2001, in which the main objective is to measure small dynamic displacements by analysis of L1 GPS carrier frequency with 1575.42 MHz—wavelength 19.05 cm, under an adaptive method for collecting data and filtering techniques. This method, named Phase Residual Method (PRM) is based on the frequency domain analysis of the phase residuals resulted from the L1 double difference static data processing of two satellites in almost orthogonal elevation angle. In this work it is proposed to obtain the phase residuals directly from the raw phase observable collected in a short baseline during a limited time span, in lieu of obtaining the residual data file from regular GPS processing programs. In order to improve the ability to detect millimetric displacements, two filtering techniques are introduced. The first one is the autocorrelation that reduces the phase noise with random time behavior. The other one is the running mean to separate low frequency from the high frequency phase sources. Two trials are presented to verify the proposed method and filtering techniques applied. One simulates a 2.5 millimeter vertical GPS antenna displacement and the second using the data collected during a bridge dynamic load test. The results show a good consistency to detect millimetric oscillations from L1 frequency and filtering techniques.

A Behavior Level Analytical Method of Electromagnetic Susceptibility for Radio Frequency Receiver

Based on simplified Volterra model, a behavior-level simulation analysis approach of electromagnetic susceptibility （EMS） for radio frequency （RF） receiver is presented in this article. Third order simplified Volterra model is adopted to analyze receiver EMS. A general criterion for EMS is proposed according to EMS response characteristics in frequency domain, and then the simulation flow charts for calculating susceptibility thresholds are given. This approach is superior to the previous EMS analysis method on receiver, which mainly relies on experiments but lack simulation analysis. Take the dual frequency GPS receiver and zero IF receiver interfered by continue wave as examples for in-band and out-of-band susceptibility threshold calculation. Simulation results show that the proposed method is not only valid and effective, but also reduces the internal storage and simulation time, which is suitable to RF receiver EMS analysis and practical in engineering and technology field.

Performance analysis of source ranging by use of virtual receiver technique under different frequency bands

The traditional matched field processing localization need complicated computation to get the replica field and has high dependence on environment parameters and acoustic field model. To overcome the shortcoming, virtual receiver technique is used for source ranging. A virtual receiver is constructed by correlating the two signals of the guide source and the objective source received by a vertical line array. Then, the slope of the interference striation of the virtual field is estimated using relevant signal processing method. Combining with the waveguide invariant/3, the range of the objective source is determined. Through the numerical simulations and data processing collected from the experiment carried out in the South China Sea in 2004, the virtual receiver technique for broadband source ranging under the slope- bottom shallow water environment is discussed. As the frequency increases, the frequency bands should be broadened to obtain complete interference striation for good ranging results. In data processing, the receiving array spacing is too large to promise the orthogonality of the modes as the frequency increases and ranging results become worse.

Microwave Reflectometry on HL-2A Tokamak

One of the most important electron density diagnostics, microwave reflectometry, has been developed on many large and medium nuclear fusion devices in recent years . Not only the electron density profiles with high temporal and spatial resolutions, but also the profiles of plasma rotation and turbulence can be obtained with this diagnostic system.

A RF receiver frontend for SC-UWB in a 0.18-μm CMOS process

A radio frequency （RF） receiver frontend for single-carrier ultra-wideband （SC-UWB） is presented. The front end employs direct-conversion architecture, and consists of a differential low noise amplifier （LNA）, a quadrature mixer, and two intermediate frequency （IF） amplifiers. The proposed LNA employs source inductively degenerated topology. First, the expression of input impedance matching bandwidth in terms of gate-source ca- pacitance, resonant frequency and target Sll is given. Then, a noise figure optimization strategy under gain and power constraints is proposed, with consideration of the integrated gate inductor, the bond-wire inductance, and its variation. The LNA utilizes two stages with different resonant frequencies to acquire flat gain over the 7.1-8.1 GHz frequency band, and has two gain modes to obtain a higher receiver dynamic range. The mixer uses a double bal- anced Gilbert structure. The front end is fabricated in a TSMC 0.18-μm RF CMOS process and occupies an area of 1.43 mm2. In high and low gain modes, the measured maximum conversion gain are 42 dB and 22 dB, input 1 dB compression points are -40 dBm and -20 dBm, and Sll is better than -18 dB and -14.5 dB. The 3 dB IF bandwidth is more than 500 MHz. The double sideband noise figure is 4.7 dB in high gain mode. The total power consumption is 65 mW from a 1.8 V supply.