Study of relationship between motion of mechanisms in gas operated weapon and its shock absorber

The article deals with the motion of the breech block carrier and the weapon casing of an automatic weapon mounted on a flexible carriage and the base of the weapon.Earlier works,which did not consider the dynamic properties of the base of the weapon,did not allow to reconcile the calculated and experimental results of the weapon casing displacement when shooting from firing rests.For the analysis of the motion of individual parts,the methods of mathematical modelling and firing experiments using a high-speed camera were chosen.Calculations show the best accord with experiment when modelling the system with 4 degrees of freedom.The oscillation of the system regarding the movement of the breech block carrier and the weapon casing was investigated under changed conditions of rate of fire,the use of a muzzle brake and different types of shock absorbers.The velocities and displacements of the weapon casing and the breech block carrier at different values of the impulse of the gases to the breech block carrier were determined.

A New Simulation Model for Recoil Analysis of Deep-Water Drilling Risers After Emergency Disconnection

The recoil response of a deep-water drilling riser following an ED(Emergency Disconnection)scenario is a transient and sensitive process.The recoiling displacement of the riser is the resultant of recoil motion and axial stretch.How-ever,it is typically represented by one variable in recoil simulations.As axial deformation is quite small compared with axial motion in the recoil process,it inevitably introduces numerical errors(i.e.,a large number annihilating a small number).Thus,it is hard to perform a quantitative analysis of axial deformation,although a consensus initial deformation is essential for recoil dynamics.Moreover,the triggered axial natural modes have never been examined before.In this study,the recoil response is decomposed into two parts:recoil motion and axial deformation,and a novel model is developed by Galerkin method.It has demonstrated that the initial stretch has a significant effect at the initial stage in recoil.The existing models underestimate the effects of axial deformation.The new model can capture information of triggered natural modes and figure out the modes undergoing dynamic compression.This study can be beneficial to overpull setting,determination of ED time and anti-recoil control optimization.

Temperature influences of the recoil characteristics for aluminum honeycomb buffer in the tether-net launcher

Fluctuations in outer space's temperature would affect the spacecraft's regular operation.This paper aims to study the temperature influences of the aluminum honeycomb buffer in the tether-net launcher.Firstly,a buffer structure was designed to attenuate the pyroshock generated by the pyrotechnic device.Secondly,the mechanical properties of aluminum honeycomb at different temperatures were obtained through quasi-static compression experiments.Then,the internal ballistic responses of the launcher were gained by the closed bomb tests and the equivalent classical interior ballistic model.Finally,the recoil performance of the launcher with aluminum honeycomb buffer at different temperatures was studied.It is revealed that the aluminum honeycomb crushing force gradually decreases with the temperature increases.The peak pressure,burning rate coefficient and velocity increase while the peak time decreases with the temperature increase for the interior ballistics.For the launcher recoil responses,the average launch recoil decreases if the aluminum honeycomb doesn't enter the dense stage.The impact acceleration,projectile velocity and displacement increase as the temperature increase.The paper spotlights the temperature's influence on the recoil characteristics of the aluminum honeycomb buffer,which provides a new idea for buffering technology of pyrotechnic devices in a complex space environment.

Effect Due to the Particle Nature of the Doppler Shifted Radiation on the Dynamics of the Spherical Light Emitting Source

The Doppler effect is a phenomenon of intrinsic kinematic character. This paper analyzes the kinematic Doppler effect for the case where the source is moving and the observer is at rest in the classical limit. The particle nature properties of radiation are considered and how it affects the dynamics of the Source has been studied. The dynamical and kinematical equations have been derived by considering this effect. It has been conclusively shown that a moving light-emitting source experiences a finite recoil momentum in the direction opposite to the direction of motion and come to rest in finite time.

BBK模型中非一阶效应和交换效应的理论研究

用BBK模型和修正后的BBK模型对低能、共面非对称几何条件下电子离化氢原子的三重微分散射截面进行了计算,并把结果与一级玻恩近似下的计算结果以及实验数据进行了比较,对修正后的BBK模型中非一阶效应和交换效应进行了分析和探讨.发现该模型中末态三体间的屏蔽包含了极强的非一阶效应信息.

低能氢原子(e,2e)反应中非一阶效应的理论研究

用BBK模型和修正后的BBK模型对入射能为27.2eV时,共面非对称几何条件下电子离化氢原子的三重微分散射截面进行了计算,并把结果与一级玻恩近似下的计算结果以及实验数据进行了比较,对修正后的BBK模型中非一阶效应进行了分析和探讨.

C^(6+)单离化氦原子反应TDCS的分析与讨论

在共面非对称几何条件下,将能壳上跃迁矩阵元表示为结构因子和末态道两粒子间关联因子的乘积,推导出C6+离化He原子在不同动量转移下三重微分散射截面解析表达式,分析了实参数和有效电荷对散射截面角分布的影响.

正交投影对三重微分散射截面(TDCS)的影响

从跃迁矩阵元的后滞形式出发,计算了在入射能量为150 eV,敲出能量分别为3 eV和5 eV,散射角1θ=16°的TDCS.取末态波函数为库仑波函数和平面波函数的乘积;初态波函数为平面波、类氢离子基态波和库仑因子C12的乘积;通过正交投影使跃迁矩阵元的后滞形式第一项为零,另外还考虑了屏蔽效应,这样所得出的理论计算结果与实验数值符合的更好了.

C^(6+)单离化氦原子反应TDCS的研究

在共面非对称几何条件下,分析了C6+离化He原子在出射电子能量为E2=1eV,动量转移分别为0.45a.u.、0.65a.u.和1.0a.u.时的三重微分散射截面,讨论了不同动量转移下的三重微分散射截面随散射角的曲线变化,得到了与实验结果比较相似的结果.

由Recollement导出的t-结构的非退化性和有界性

根据Beilinson A,Bernstein J,Deligne P的结论可知,若三个三角范畴允许有一个Recollement,则Recollement两端三角范畴上的t-结构可以诱导中间三角范畴上的一个t-结构.在这篇文章中讨论了这三个t-结构在非退化性和有界性上的联系.首先证明了两端三角范畴上的t-结构是非退化的当且仅当中间三角范畴上的t-结构是非退化的.其次证明了两端三角范畴上的t-结构是有界的当且仅当中间三角范畴上的t-结构是有界的.最后讨论了Recollement函子的t-正合性.

电子碰撞电离氦原子的三重微分截面

在一级玻恩近似理论框架下,用分波法计算入射电子能量分别为634.59、604.59、400、250、150 eV的氦原子(e,2e)反应的三重微分截面(TDCS),并与实验结果进行比较.在入射电子能量为604.59、400、250 eV情况下,全扭曲波玻恩近似与实验较为符合;在入射电子能量为634.59 eV情况,其敲出电子能量40 eV条件下,考虑敲出电子库仑势的计算结果好于考虑敲出电子扭曲势的计算结果.在固定散射角情况下,Recoil峰的相对强度和Binary峰值位置随敲出电子能量变化的趋势,与文献(Ehrhatdt H,Hesselbacher K H,Jung K,et al.Collisional ionization of helium by 250 eV electrons:experiments with completely determined kinetics[J].J Phys B:At Opt Mol Phys,1972,5:2107-2116)中提到的变化趋势一致.

Coupling Effects of A Deep-Water Drilling Riser and the Platform and the Discharging Fluid Column in An Emergency Disconnect Scenario

As drilling operations move into remote locations and extreme water depths, recoil analysis requires more careful considerations and the incidence of emergency disconnect is increased inevitably. To accurately capture the recoil dynamics of a deep-water riser in an emergency disconnect scenario, researchers typically focus on modelling the influential subsystems (e.g., the tensioner, the mud discharge and seawater refilling process) which can be solved in the preprocessing, and then the determined parameters are transmitted into an existing global riser analysis software. Distinctively, the current study devotes efforts into the coupling effects resulting from that the suspended riser reacts the platform heave motion via the tensioner system in the course of recoil and the discharging fluid column follows the oscillation of the riser in the mud discharge process. Four simulation models are established based on lumped mass method employing different formulas for the top boundary condition of the riser and the discharging flow acceleration. It demonstrates that the coupling effects discussed above can significantly affect the recoil behavior during the transition phase from initial disconnect to the final hang-off state. It is recommended to develop a fully- coupled integrated model for recoil analysis and anti-recoil control system design before extreme deep-water applications.

Complex experimental analysis of rifle-shooter interaction

In this study, a complex analysis of a man-weapon interaction based on experimental effort is presented.The attention is focused on how a shooter can influence on a rifle, opposite to generally considered in literature rifle's impact on a shooter. It is shown, based on the kbk AKM weapon, that each support point of the rifle has an substantial impact on the system. It is said that identifying human reactions on weapon may let to describe gun movement and thus may be applied to weapon accuracy determination.

A prediction method for the performance of a low-recoil gun with front nozzle

One of the greatest challenges in the design of a gun is to balance muzzle velocity and recoil,especially for guns on aircrafts and deployable vehicles.To resolve the conflict between gun power and recoil force,a concept of rarefaction wave gun(RAVEN)was proposed to significantly reduce the weapon recoil and the heat in barrel,while minimally reducing the muzzle velocity.The main principle of RAVEN is that the rarefaction wave will not reach the projectile base until the muzzle by delaying the venting time of an expansion nozzle at the breech.Developed on the RAVEN principle,the purpose of this paper is to provide an engineering method for predicting the performance of a low-recoil gun with front nozzle.First,a two-dimensional two-phase flow model of interior ballistic during the RAVEN firing cycle was established.Numerical simulation results were compared with the published data to validate the reliability and accuracy.Next,the effects of the vent opening times and locations were investigated to determine the influence rules on the performance of the RAVEN with front nozzle.Then according to the results above,simple nonlinear fitting formulas were provided to explain how the muzzle velocity and the recoil force change with the vent opening time and location.Finally,a better vent venting opening time corresponding to the vent location was proposed.The findings should make an important contribution to the field of engineering applications of the RAVEN.

Ag^+(4d^(10))离子三重微分截面的研究

用自旋平均静态交换势下的三体扭曲波波恩近似计算了d轨道电子 (Ag+ (4d10 ) )在共面非对称几何条件下的三重微分截面 ,结果表明在高入射能的条件下 ,随散射电子角度θa的增加 ,bina ry峰和recoil峰分裂的个数都会增加 ,电子的电离振幅会随之下降 ,d电子的三重微分截面比s。

Measurement of the prompt neutron spectrum from thermalneutron-induced fission in U-235 using the recoil proton method

A measurement of the ^235U prompt fission neutron spectrum (PFNS) by the recoil proton method was performed at the Institute of Nuclear Physics and Chemistry, China. Details of the method, which include the calculation and validation of the response matrix, are presented. The PFNS for ^235U in the energy range 1–12 MeV, induced by thermal neutrons, was obtained. The measured spectrum in the low-energy region was in good agreement with previous work and the ENDF/B-VII library, except for minor differences. In the high-energy region, however, the relative height of the measured spectrum was greater, and an analysis of the experiment indicated uncertainties of 13% at 10 MeV and 24% at 12 MeV. Experimental results showed that the recoil proton method could be used to measure prompt fission neutron spectra. Some directions for future work are included.

Propagation of positive, negative, and recoil leaders in upward lightning flashes

Leader propagation is a fundamental issue in lightning physics. The propagation characteristics of positive leaders and negative leaders are summarized and compared based on data from high-speed camera and electromagnetic field in rocket-triggered lightning and tower-initiated lightning discharges; available channel base current data recorded in rocket-triggered lightning are also used. The negative leaders propagate in a stepped fashion accompanied by many branches. The stems ahead of the negative leader tip determine the manner and direction of the leader propagation, and even the branching and winding of the lightning channel. The impulsive current, electromagnetic field, and related optical images suggest that the positive leader may develop in a step-like fashion at its initial stage of triggered lightning. However, the stepping processes of the positive leader are obviously different from those of the negative leader. Tower-initiated lightning revealed that the most conspicuous characteristics of the stepwise positive leader involve the intermittent brush-like corona zone in front of the leader tip and the luminosity enhancement of the channel behind the tip. In rockettriggered lightning flashes, the charge transferred during an individual step for the negative leader was nearly an order greater than for the positive counterpart. The successive streamers ahead of the leader tip are essential for both negative and positive leader propagation, and the stems could be formed from one or more streamers in the previous negative streamer zone with the main leader channel dim. High-resolution observation of tower lightning also revealed a new type of bidirectional recoil leader, with polarity contrary to the traditional one, traversing in negative channels associated with tower-initiated and rocket-triggered lightning.

Investigation of enhancement in planar fast neutron detector efficiency with stacked structure using Geant4

Geant4 based Monte Carlo study has been carried out to assess the improvement in efficiency of the planar structure of Silicon Carbide(SiC)-based semiconductor fast neutron detector with the stacked structure. A proton recoil detector was simulated, which consists of hydrogenous converter, i.e., high-density polyethylene(HDPE) for generating recoil protons by means of neutron elastic scattering(n, p) reaction and semiconductor material SiC, for generating a detectable electrical signal upon transport of recoil protons through it. SiC is considered in order to overcome the various factors associated with conventional Si-based devices such as operability in a harsh radiation environment, as often encountered in nuclear facilities. Converter layer thickness is optimized by considering 10~9 neutron events of different monoenergetic neutron sources as well as ^(241)Am-Be neutron spectrum. It is found that the optimized thickness for neutron energy range of 1–10 MeV is ~400 μm. However, the efficiency of fast neutron detection is estimated to be only 0.112%,which is considered very low for meaningful and reliable detection of neutrons. To overcome this problem, a stacked juxtaposition of converter layer between SiC layers has been analyzed in order to achieve high efficiency. It is noted that a tenfold efficiency improvement has been obtained—1.04% for 10 layers stacked configuration vis-à-vis 0.112% of single converter layer detector. Further simulation of the stacked detector with respect to variable converter thickness has been performed to achieve the efficiency as high as ~3.85% with up to 50 stacks.

Research and development of training pistols for laser shooting simulation system

Firearm shooting simulators are effective means for training the personnel in armed forces,police and shooting athletes.Shooter-weapon is a complex biomechanical system,therefore the best training quality is achieved when the process of a weapon shot is reconstructed in a training simulator and its training weapon mimics the(feeling) perception of the real weapon usage.Dynamics of motions of a handgun simulator held in the hand of a shooter by its grip during the shot is analysed theoretically and experimentally.Breech lock mechanism of the simulator is actuated pneumatically by supplying compressed air in pulses from external pressure source.Analysis of the obtained simulation results and experimentally recorded motion parameters of the training weapon body reveals that application of pneumatic drives is a reasonable option to simulate recoil perception of a pistol.

Dynamics of Polymeric Fluids：Part Ⅱ The Molecular Theory of Die Swell： Correlation of Ultimate Die Swelling Effect to the Molecular Parameters and the Operational Variables

A general expression for the correlation of the simple shear （tanφ） to the molecular parameters and the shear rate （·↑γ） was deduced. It shows that the simple shear （tanφ） may be resolved into free recoil （recoverable strain） and viscous heating （unrecoverable strain）. The magnitudes of the simple shears for recoil （tanφE） and （tanφv） for viscous heating not only depended on the molecular parameters and the operational variables, but also on the exponential fractions of the recoverable （1--↑W·↑γ） and unrecoverable （-↑W·↑γ） conformations for recoil and viscous heating. Therefore the magnitudes of the simple shears （tanφE） for recoil and （tanφv） for viscous heating are, respectively, expressed as the partition function to the （1--↑W·↑γ）th power and the partition function to the （-↑W·↑γ）th power. Thus correlations of the total recoil and the ultimately recoverable strains to the molecular parameters [n′, α, η0, GN^0 and （1--↑W·↑γ）] and the operational variables （·↑γ, （L/D） and tr） were deduced respectively, which show that at very different shear rates （0≤·↑γ≤∞） the polymeric liquids may exhibit a very different viscoelastic behaviors. After introducing the uniform two-dimensional extension, the definition of swelling ratio and the ratio of L to D [De=（L/D）], two expressions for the ultimate die swelling effect and the ultimate extrudate swelling ratio BEVT5 to the molecular parameters [n′, α, η0, GN^0 and （1--↑W·↑γ）] and the operational variables （·↑γ, （L/D） and tr） were obtained. The two correlation expressions were verified by the experimental data of high-density polyethylene （HDPE） which shows that the two correlation expressions can be used to predict the correlations of the ultimate extrudate swelling behaviors of polymeric liquids to the molecular parameters and the operational variables.