Cross-sectional distortion behaviors of thin-walled rectangular tube in rotary-draw bending process

The cross-sectional distortion usually appears during rotary-draw bending process of thin-walled rectangular tube with small bending radius.To study the cross-sectional distortion of the tube,a three-dimensional finite-element model of the process was developed based on ABAQUS/Explicit code and its reliability was validated by experiment.Then,the cross-sectional distortion behaviors of the tube were investigated.The results show that a zone of larger circumferential stress appears on the tube when bending angle reaches 30°.And in the larger circumferential stress zone,the sagging phenomenon is produced obviously.The maximum cross-sectional distortion is located in the larger circumferential stress zone and the angle between the plane of maximum cross-sectional distortion and the bending reference plane is about 50°.The position of the maximum cross-sectional distortion keeps almost unchanged with the variation of the clearances between dies and tube.

Saint-Venant torsion analysis of bars with rectangular cross-section and effective coating layers

This paper investigates the torsion analysis of coated bars with a rectangular cross-section. Two opposite faces of a bar are coated by two isotropie layers with different materials of the original substrate that are perfectly bonded to the bar. With the Saint- Venant torsion theory, the governing equation of the problem in terms of the warping function is established and solved using the finite Fourier cosine transform. The state of stress on the cross-section, warping of the cross-section, and torsional rigidity of the bar are evaluated. Effects of thickness of the coating layers and material properties on these quantities are investigated. A set of graphs are provided that can be used to determine the coating thicknesses and material properties so as to keep the maximum von Mises stress on the cross-section below an allowable value for effective use of the coating layer.

Measurement and Correlation of Pressure Drop for Gas-Liquid Two-phase Flow in Rectangular Microchannels

The pressure drop of gas-liquid two-phase flow in microchannel is of fundamental importance in heat and mass transfer processes. In this work,the pressure drop of gas-liquid two-phase flow in horizontal rectangular cross-section microchannels was measured by a pressure differential transducer system. Water,ethanol and n-propanol were used as liquid phase to study the effects of capillary number on pressure drop;air was used as the gas phase. Four microchannels with various dimensions of 100 μm× 200 μm,100 μm× 400 μm,100 μm× 800 μm and 100 μm× 2000 μm(depth × width) were used for determining the influence of configuration on the pressure drop. Experimental results showed that in micro-scale,the capillary number also affected the pressure drop remarkably,and in spite of only one-fold difference in aspect ratio,the variation of pressure drop reached up to near three times under the same experimental conditions. Taking the effects of aspect ratio and surface tension into account,a modi-fied correlation for Chisholm parameter C in the Chisholm model was proposed for predicting the frictional multi-plier,and the predicted values by the proposed correlation showed a satisfactory agreement with experimental data.

PLASTIC POST－BUCKLING OF A SIMPLY SUPPORTED COLUMN WITH A SOLID RECTANGULAR CROSS－SECTION

The plastic post-buckling of a simply supported column with a solid rectangularcross-section is analysed by a new approach. High order terms in the asymptotic post-buckling expansions are carried out. In some aspects, the method proposed in thispaper is similar io Hutchinson's. However, the computation is simple since theintroduction is avoided of stretched coordinates. The method can be used to analyseinitial post-bifurcation of plates and shells in the plastic range.

Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube(DRRT)with high forming quality is helpful to improve the microwave transmission accuracy.For reducing the cross-sectional deformation in the H-typed bending process,in addition to using rigid mandrel to support the inside of tube,ridge groove fillers are also added to restrict the deformation of ridge grooves.Because of the change of stress and strain state of bent tube in bending,rigid mandrel retracting and specially twicespringback stages,and the springback of fillers,the cross-sectional deformation of tube in each stage may be different.Therefore,based on the ABAQUS platform,the finite element models(FEM)for H-typed bending,mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated.It is found that,for the height and width deformation of tube and spacing deformation of ridge grooves,retraction of mandrel can make the distribution of these deformations more uniform along the bending direction.The first springback can reduce these deformations significantly,which should be emphasized.But the second springback only increases them by less amount,which can be ignored.The smaller height deformation of ridge groove and filler can be neglected.

Cross-sectional deformation of H96 brass double-ridged rectangular tube in rotary draw bending process with different yield criteria

Different yield criterion has great difference in predicting the deformation of tube with different material.In order to improve the prediction accuracy of the cross-sectional deformation of the double-ridged rectangular tube(DRRT)during rotary draw bending(RDB)process,Mises isotropic yield criterion,Hill’48 and Barlat/Lian anisotropic yield criteria commonly used in practical engineering are introduced to simulate RDB of DRRT.The inverse method combining uniaxial tensile test of whole tube and response surface methodology was proposed to identify the parameters of Hill’48 and Barlat/Lian yield criteria of small-sized H96 brass extrusion DRRT as well.Then based on ABAQUS/Explicit platform,the FE models of RDB process of DRRT considering Mises,Hill’48 and Barlat/Lian yield criteria were built.The results show that:The variation trend of cross-sectional deformation ratio is same when using different yield criteria.The cross-sectional deformation ratio by using Mises yield criterion is close to that by using Hill’48 yield criterion.However,there is a quite difference between by using Barlat/Lian yield criterion and by using Mises or Hill’48 yield criteria.The prediction values of cross-sectional height deformation by using three yield criteria all underestimate the experiment ones,and the prediction values of cross-sectional width deformation overestimate the experiment ones.By comparing the simulation results of cross-sectional deformation of the DRRT with different yield criteria and experiment ones,Barlat/Lian yield criterion is found to be suitable for describing the RDB process of DRRT.

用于软土地区深基坑支护的格栅状地下连续墙

针对深基坑支护工程中围护结构的受力特点,提出一种经济、节能、环保的新型围护结构———格栅状地下连续墙,即利用液压振动装置将"回"形钢模连续地压入土中,并在其中插入钢筋笼和现场灌注混凝土,以形成格栅状连续墙体。介绍了"回"形钢模的设计思路以及格栅状地下连续墙的施工方法,并通过现场试验进行成墙质量的验证。将该支护形式与传统的围护结构进行了对比,分析结果表明,该围护结构较好地发挥了材料性能,能耗低,同时施工现场文明,具有研究和推广价值。

An exact analytical solution for convective heat transfer in rectangular ducts

An exact analytical solution is obtained for convective heat transfer in straight ducts with rectangular cross-sections for the first time.This solution is valid for both H1 and H2 boundary conditions,which are related to fully developed convective heat transfer under constant heat flux at the duct walls.The separation of variables method and various other mathematical techniques are used to find the closed form of the temperature distribution.The local and mean Nusselt numbers are also obtained as functions of the aspect ratio.A new physical constraint is presented to solve the Neumann problem in non-dimensional analysis for the H2 boundary conditions.This is one of the major innovations of the current study.The analytical results indicate a singularity occurs at a critical aspect ratio of 2.4912 when calculating the local and mean Nusselt numbers.