Advancements in Sound Reflection and Airborne Sound Insulation Measurement on Noise Barriers

The in-situ measurement of sound reflection and airborne sound insulation characteristics of a noise barrier in Europe are currently performed following the CEN/TS 1793-5 European standard guidelines (last revision published in 2003 [1]). After some years a large number of barriers measured, the original method has been significantly enhanced and validated in the frame of the EU funded QUIESST project, WP3 [2]. The sound reflection measurement method has been improved using a square 9-microphone grid not rigidly connected to the loudspeaker, an optimized alignment algorithm of free-field and reflected impulse responses, including fractional step shifts and least squares estimation of the best relative position, and a correction for geometrical divergence and sound source directivity. Each single measurement is then validated by means of the Reduction Factor calculation. The airborne sound insulation measurement method has not been markedly changed since 2003, because the procedure is robust and easily applicable as it is, but some problems may still be encountered when measuring highly insulating noise barriers, due to a poor signal to noise ratio of the transmitted impulse response. In those cases it is difficult to realize just after the measurement whether the obtained data are valid or not. A method, applicable on site, to overcome this problem is described here. It is based on the Signal to Noise Ratio estimation of critical parts of the acquired impulse responses and gives a strong validation criterion.

Precise Optical Fiber Length Measurement System Based on Fresnel Reflection

In this study, a precise optical fiber length measurement system is proposed. The measurement technique is based on the measurement of relative Fresnel reflected light intensity in a test fiber. Time delayed optical reflected pulses are obtained from a single nanosecond pulse injected at the input due to the difference in lengths of the reference and test fibers. The lengths of the different optical fibers have been measured with this technique with high resolution and fast response time. The measured results show that, the proposed technique has a comparable performance with the well-known length measurement systems.

Reflectivity Measurement of Weak Fiber Bragg Grating (FBG)

One method based on the end-face reflection as a reference was used to measure weak grating reflectivity of 0.01%-1%. For measuring ultra-weak grating reflectivity, the grating group with an identical wavelength was used. By using anhydrous alcohol and deionized water as the reflecting medium, the single- pulse FBG reflectivity of a highly doped-Ge photosensitive fiber was calculated to be about 0.747% and 0.739%, respectively; and the single-pulse FBG reflectivity of ordinary SMF fiber was about 0.016% and 0.015%, respectively. The consistent results by the two different reflecting media showed that the end-face reflection method on the grating group was feasible.

The Method of Solutions for some Kinds of Singular Integral Equations of Convolution Type with Both Reflection and Translation Shift

In this paper,some kinds of singular integral equations of convolution type with reflection and translation shift are discussed and they are turned into Riemann boundary value problems with both discontinuous coefficients and reflection by using the Fourier transform.In spite of the classical method for solution,we are to give another method,therefore the general solution and condition of solvability are obtained in class{0}.

High-precision measurement of low reflectivity specular object based on phase measuring deflectometry

Phase measuring deflectometry(PMD)is a robust,noncoherent technique for the characterization of specular surface.For measuring high specular reflectivity surface,PMD can deliver micron radian range local gradient.However,when the measured surface has low specular reflectivity,the accuracy of the measured gradient is low since the captured fringe pattern shows low signal to noise ratio.The phase error characteristics in PMD system when testing low reflectivity surfaces are analyzed.The analysis illustrates that the random phase error increases rapidly while the nonlinear error drops slowly with the decreasing of the tested surface reflectivity.In order to attain high precision measurement of low reflectivity specular surface,a robust error reduction method based on wavelet de-noising is proposed to reduce the phase error.This error reduction method is compared with several other normally used methods in both simulation and experiment work.The method based on the wavelet de-noising shows better performance when measuring the low reflectivity specular surface.

Review of reflective fiber optic sensors for surface topography measurement

Different from the traditional contact surface topography measurement,reflective intensity-modulated fiber optic sensor(RIM-FOS)has the unique advantages of non-contact nondestructive detection.This paper briefly introduces the principle and performance of RIM-FOS for surface topography measurement and compares with several other methods of topography measurement.Based on the review of its development process,this paper summarizes and analyses the hot issues of RIM-FOS in the surface topography measurement,then predicts the future trend for a guidance of the further study.

Reflection-type holographic disk-type memory using three-dimensional speckle-shift multiplexing

This review presents a reflection-type holographic memory using three-dimensional(3D)speckle-shift multiplexing. First, the schematic of the proposed memory system was described. Then,experimental demonstrations of multiplexing in plane and along the depth direction were presented. The estimated storage capacity of single layer recording was introduced and the maximum storage capacity was discussed. To increase the storage capacity, the multi-layered recording was described. In the multilayered recording, the storage capacity can be increased by appropriate arrangement of holograms in each layer.

Entanglement swapping without joint measurement via a ∧-type atom interacting with bimodal cavity field

This paper proposes a scheme for realizing entanglement swapping in cavity QED. The scheme is based on the resonant interaction of a two-mode cavity field with a ∧-type three-level atom. In contrast with the previously proposed schemes, the present scheme is ascendant, since the fidelity is 1.0 and the joint measurement isn＇t needed. And the scheme is experimentally feasible based on the current cavity QED technique.

Proposal and Verification of Simultaneous Measurement Method for Three Thermoelectric Properties with Film-Type Thermocouple Probe

A new simultaneous measurement method for the measurement of the three thermoelectric properties with a film-type thermocouple probe was proposed. Seebeck coefficient was measured using the steady-state condi-tion of the differential method. The electrical resistivity was measured us-ing the four-probe method and the thermal diffusivity is measured using the periodic heating method. The effectiveness of the proposed method was verified using constantan as a reference material. After describing the effectiveness of the method, the measurement of three thermoelectric properties of Bi0.3Sb1.7Te3, which is a thermoelectric material, was per-formed.

Schottky Barrier Parameters of Pd/Ti Contacts on N-Type InP Revealed from I-V-T And C-V-T Measurements

We report on the current-voltage (I-V) and capacitance-voltage (C-V) characteristics of the Pd/Ti/n-InP Schottky barrier diodes (SBDs) in the temperature range 160-400 K in steps of 40 K. The barrier heights and ideality factors of Schottky contact are found in the range 0.35 eV (I-V), 0.73 eV (C-V) at 160 K and 0.63 eV (I-V), 0.61 eV (C-V) at 400 K, respectively. It is observed that the zero-bias barrier height decreases and ideality factor n increase with a decrease in temperature, this behaviour is attributed to barrier inhomogeneities by assuming Gaussian distribution at the interface. The calculated value of series resistance (Rs) from the forward I-V characteristics is decreased with an increase in temperature. The homogeneous barrier height value of approximately 0.71 eV for the Pd/Ti Schottky diode has been obtained from the linear relationship between the temperature-dependent experimentally effective barrier heights and ideality factors. The zero-bias barrier height ( ) versus 1/2kT plot has been drawn to obtain evidence of a Gaussian distribution of the barrier heights and values of = 0.80 eV and = 114 mV for the mean barrier height and standard deviation have been obtained from the plot, respectively. The modified Richardson ln(I0/T2)- ( ) versus 1000/T plot has a good linearity over the investigated temperature range and gives the mean barrier height ( ) and Richardson constant (A*) values as 0.796 eV and 6.16 Acm-2K-2 respectively. The discrepancy between Schottky barrier heights obtained from I-V and C-V measurements is also interpreted.

Accurate Measurement Method for Tube's Endpoints Based on Machine Vision

Tubes are used widely in aerospace vehicles, and their accurate assembly can directly affect the assembling reliability and the quality of products. It is important to measure the processed tube＇s endpoints and then fix any geometric errors correspondingly. However, the traditional tube inspection method is time-consuming and complex operations. Therefore, a new measurement method for a tube＇s endpoints based on machine vision is proposed. First, reflected light on tube＇s surface can be removed by using photometric linearization. Then, based on the optimization model for the tube＇s endpoint measurements and the principle of stereo matching, the global coordinates and the relative distance of the tube＇s endpoint are obtained. To confirm the feasibility, ll tubes are processed to remove the reflected light and then the endpoint＇s positions of tubes are measured. The experiment results show that the measurement repeatability accuracy is 0.167 mm, and the absolute accuracy is 0.328 ram. The measurement takes less than 1 min. The proposed method based on machine vision can measure the tube＇s endpoints without any surface treatment or any tools and can realize on line measurement.

The levels of serum fibrosis marks and morphometric quantitative measurement of hepatic fibrosis

Objective: To study the relationship between the ser- um levels of hyaluronic acid (HA), procollagen type Ⅲ (PCⅢ), collagen type Ⅳ (CIV) and the histologi- cal degree of hepatic fibrosis evaluated by image analysis, and the clinical significance of serum HA, PC Ⅲ, C Ⅳ in the diagnosis of hepatic fibrosis in pa- tients with chronic viral hepatitis. Methods: The concentrations of serum HA, PC Ⅲ, C Ⅳ in 151 patients with chronic viral hepatitis were measured by radioimmunoassay. Liver biopsies were performed in all the patients. Histological sections of 4 μm thickness were stained with Masson's trichrome for fibrosis assessment. Morphometric quantitative measurements for hepatic fibrosis assessment in the 4 μm sections were performed using a fully automated image analysis system. Serum levels of HA, PC Ⅲ, and C Ⅳ were analyzed at different stages of liver pa- thology and compared with the morphometric quanti- tative measurements of hepatic fibrosis. Results: The serum levels of HA, PC Ⅲ, C Ⅳ all ele- vated gradually with the progression of the disease, and all reached the highest in patients with liver cir- rhosis. There was a significant difference in the levels of these 3 components between liver cirrhosis group and the other groups (P<0.05). They all increased steadily with the histological stages of hepatic fibrosis, and reached the highest levels in stage Ⅳ. The serum levels of HA, PC Ⅲ, C Ⅳ were all positive- ly correlated with the histological stages of liver sec- tions and the morphometric measurement (P< 0.001). The coefficients with stages were 0.694, 0.493, 0.552 (P<0.001), respectively and with sur- face density of total collagen on liver biopsy sections by image analysis were 0. 715, 0. 595, 0. 573 (P< 0.001), respectively. Conclusion: The serum levels of HA, PC Ⅲ, C Ⅳ were in consistent with the degree of hepatic fibrosis, and the determination of these marks is valuable for detecting hepatic fibrosis.

Transmitted and Reflected Coefficients for Horizontal or Vertical Plate Type Breakwater

Surface or submerged horizontal or vertical plate can be considered as a new concept breakwater. This paper investigates the wave-plate interaction of this type of breakwater by use of the boundary element method. The relationships of wave transmitted and reflected among plate thickness, submergence and length are carefully studied by numerical simulation. It is shown that： （1） The transmitted coefficients of submerged horizontal plate or vertical plate will become larger with the increase of plate thickness and reduce rapidly with the decrease of plate submergence. （2） Both surface horizontal and vertical plate are efficient for intermediate and short wave elimination, but vertical plate is more effective. （3） Submerged horizontal plate can act more effectively than submerged vertical plate does. With all wave frequencies, the vertical plate almost has no wave elimination effect.

Error analysis of non-spherical raindrops on precipitation measurement

Radar cross section （RCS） of non-sphericai raindrops is calculated by using the software CST based on finite integral method and compared with RCS of spherical raindrops. The revised factor of non-spherical raindrops is obtained. The radar reflectivity with precipitation change of four distribution models of M-P, Gamma, JD and JT combining the revised factor is gotten using trapezoidal integration. When the infuence of non-spherical raindrops is considered, the accuracy of precipitation measurement of four distribution models can be separately improved 8.77%, 8.47%, 10.53% and 8.04% in the case of rain intensity is 100 mm/h.

The Hausdorff Dimension and Hausdorff Measure of Full Parry Measure Subset of Finite Type

All the full Parry measure subsets of a given subshift of finite type determined by an irreducible 0-1 matrix have the same Hausdorrf dimension and Hausdorff measure which coincide with those of the set of finite type.

Algebraic Independence Measures for the Values of Mahler Type Functions

In this paper, we give the algebraic independence measures for the values ofMahler type functions in complex number field and p-adic number field, respectively.

Resource types, formation, distribution and prospects of coal-measure gas

Coal-measure gas is the natural gas generated by coal, carbonaceous shale, and dark shale in coal-measure strata. It includes resources of continuous-type coalbed methane (CBM), shale gas and tight gas reservoirs, and trap-type coal-bearing gas reservoirs. Huge in resources, it is an important gas source in the natural gas industry. The formation and distribution characteristics of coal-measure gas in San Juan, Surat, West Siberia and Ordos basins are introduced in this paper. By reviewing the progress of exploration and development of coal-measure gas around the world, the coal-measure gas is confirmed as an important strategic option for gas supply. This understanding is mainly manifested in three aspects. First, globally, the Eurasian east-west coal-accumulation belt and North American north-south coal-accumulation belt are two major coal-accumulation areas in the world, and the Late Carboniferous–Permian, Jurassic and end of Late Cretaceous–Neogene are 3 main coal-accumulation periods. Second, continuous-type and trap-type are two main accumulation modes of coal-measure gas;it is proposed that the area with gas generation intensity of greater than 10×10^8 m^3/km^2 is essential for the formation of large coal-measure gas field, and the CBM generated by medium- to high-rank coal is usually enriched in syncline, while CBM generated by low-rank coal is likely to accumulate when the source rock and caprock are in good configuration. Third, it is predicted that coal-measure gas around the world has huge remaining resources, coal-measure gas outside source is concentrated in Central Asia-Russia, the United States, Canada and other countries/regions, while CBM inside source is largely concentrated in 12 countries. The production of coal-measure gas in China is expected to exceed 1000×10^8 m^3 by 2030, including (500–550)×10^8 m^3 conventional coal-measure gas,(400–450)×10^8 m^3 coal-measure tight gas, and (150–200)×10^8 m^3 CBM.

Analytical Evaluation of Non-Elementary Integrals Involving Some Exponential, Hyperbolic and Trigonometric Elementary Functions and Derivation of New Probability Measures Generalizing the Gamma-Type and Gaussian-Type Distributions

The non-elementary integrals involving elementary exponential, hyperbolic and trigonometric functions, and where α,η and β are real or complex constants are evaluated in terms of the confluent hypergeometric function 1F1 and the hypergeometric function 1F2. The hyperbolic and Euler identities are used to derive some identities involving exponential, hyperbolic, trigonometric functions and the hypergeometric functions 1F1 and 1F2. Having evaluated, these non-elementary integrals, some new probability measures generalizing the gamma-type and Gaussian distributions are also obtained. The obtained generalized probability distributions may, for example, allow to perform better statistical tests than those already known (e.g. chi-square (x2) statistical tests and other statistical tests constructed based on the central limit theorem (CLT)), while avoiding the use of computational approximations (or methods) which are in general expensive and associated with numerical errors.

Research Progress on Self-Efficacy Level of Patients with Type 2 Diabetes Mellitus and Its Influencing Factors

Self-efficacy plays an important role in the management of type 2 diabetes mellitus (T2DM) patients, and it runs through the whole process of diabetes treatment, which is conducive to controlling and delaying the occurrence and development of complications, as well as improving the quality of life of patients. This paper mainly describes the concept of self-efficacy, the current situation of self-efficacy of diabetic patients at home and abroad, the functional aspects and their influencing factors, so as to take relevant measures on how to improve self-efficacy. It aims to provide a theoretical basis for the development of self-efficacy interventions for patients with type 2 diabetes mellitus.

The Type of Low-yielding Fields,Using Direction and Land Fertility Building Measures in Suiping County

Using the evaluation indicator system for arable land fertility in Suiping County,this paper analyzes some factors influencing agricultural production,such as physical and chemical properties of soil,site conditions,soil management,and soil nutrients concerning various types of low-yielding fields in the county. In accordance with the dominant soil constraint factors and main direction of improvement,the lowyielding fields in the county are divided into four types: irrigation improvement type,waterlogging drainage type,barren soil fertilization and barrier layer type. Finally this paper offers specific guidance on the construction of arable land.