Application of the porous medium combustion technology in the chamber reheating furnaces at Baosteel

The design of the porous medium combustion （PMC） system which has been applied to chamber reheating furnaces is presented in this study and its main application effects are described in detail. Porous medium materials are mainly ceramic ball sucked granular bed porous media and foam ceramic porous media. This study investigates the foam ceramic porous medium and a schematic diagram of the combustion inside this porous medium. The PMC takes a solid medium as its main heat exchange way, thus greatly improving the heat transfer efficiency. Judging from the application effects,the following conclusions have been made： the PMC technology can save more than 25% of energy with remarkable effects; the furnace temperature uniformity can be significantly enhanced; the porous media combustion technology can make the heating furnace design in a more compact way, reduce the time for heating up the furnace, improve the heating rate and reduce energy consumption.

Dynamic simulation on effect of flame arrangement on thermal process of regenerative reheating furnace

By analyzing the characteristics of combustion and billet heating process, a 3-D transient computer fluid dynamic simulation system based on commercial software CFX4.3 and some self-programmed codes were developed to simulate the thermal process in a continuous heating furnace using high temperature air combustion technology. The effects of different switching modes on injection entrancement of multi burners, combustion and billet heating process in furnace were analyzed numerically, and the computational results were compared with on-site measurement, which verified the practicability of this numerical simulation system. The results indicate that the flow pattern and distribution of temperature in regenerative reheating furnace with partial same-side-switching combustion mode are favorable to satisfy the high quality requirements of reheating, in which the terminal heating temperature of billets is more than 1 460 K and the temperature difference between two nodes is not more than 10 K. But since the surface average temperature of billets apart fi＇om heating zone is only about 1 350 K and continued heating is needed in soaking zone, the design and operation of current state are still needed to be optimized to improve the temperature schedule of billet heating. The distribution of velocity and temperature in regenerative reheating furnace with same-side-switching combustion mode cannot satisfy the even and fast heating process. The terminal heating temperature of billets is lower than that of the former case by 30 K. The distribution of flow and temperature can be improved by using cross-switching combustion mode, whose terminal temperature of billets is about 1 470 K with small temperature difference within 10 K.

Advanced control of walking-beam reheating furnace

Rehearing furnace is an important device with complex dynamic characteristicsin steel plants. The temperature tracing control of reheating furnace has great importance both tothe quality of slabs and energy saving. A model-based control strategy, multivariable constrainedcontrol (MCC) for the reheating furnace control is used. With this control method, the furnace istreated as a six-input-six-output general model with loops coupled in nature. Compared with thetraditional control, the proposed control strategy gets better temperature tracing accuracy andexhibits some energy saving feature. The simulation results show that the performance of the furnaceis greatly improved.

Numerical simulation of fluid flow in a reheating furnace with multi-swirling-burners

A general numerical simulating program for three-dimensional (3-D) andtime-dependent fluid flow for a reheating furnace with multi-swirling-burners has been developedbased upon an arbitrary Lagrangian-Eulerian scheme (ALE) with the finite volume method. Theparameters of fluid flow in a reheating furnace with multi-swirling-burners was calculated and the3-D velocity distributions were obtained. The design of the burners was optimized for forming betterswirling flow. The simulation shows that the fluid flow in the reheating furnace with the optimizedburners is reasonable.

Software sensor for slab reheating furnace

It has long been thought that a reheating furnace, with its inherent measurement difficulties and complex dynamics, posed almost insurmountable problems to engineers in steel plants. A novel software sensor is proposed to make more effective use of those measurements that are already available, which has great importance both to slab quality and energy saving. The proposed method is based on the mixtures of Gaussian processes (GP) with the expectation maximization (EM) algorithm employed for parameter esti- mation of the mixture of models. The mixture model can alleviate the computational complexity of GP and also accords with the changes of operating condition in practical processes. It is demonstrated by on-line estimation of the furnace gas temperature in 1580 reheating furnace in Baosteel Corporation (Group).

Mathematical Model of Dynamic Operation and Optimum Control of Billet Reheating Furnace

This paper provides a mathematical model for the billet reheating process in furnace.A new optimum method is brought up that the objective function is the integral value of enthalpy increasing process of a billet.Different delays are simulated and calculated,some proper delay strategies are ob- tained.The on-line computer control model is de- veloped.The real production conditions simulated, the temperature deviation of drop out billet from the target temperature is kept within±15℃.

RESEARCH ON THE DYNAMIC MATHEMATICAL MODEL OF REHEATING FURNACE

This paper presented a dynamical mathematical model for reheating furnace based on energy balance, which consists of three submodels. With the inputting parameters, adopting the finite difference technique, not only the combustion gas temperature but also the temperature distribution of slabs in the furnace can be predicated. The dynamical mathematical model is the base for the further control and it also can be treated as a simulator of a reheating furnace, optimal and advanced controlling strategies can be applied based on the dynamical model.

Present development of rolling reheating furnace technology in Shougang

By analyzing recent development of reheating furnace in Shougang,the direction of rolling reheating furnace is large type,high efficiency,lower pollution and automation etc.Many advanced technologies are integrated in new rolling reheating furnace such as working beam,regenerative combustion,evaporation cooling and hot loading and hot feeding etc.It shows that reheating furnace technology is upgraded.During the process of product structure adjustment in Shougang,because product heating quality is improved,energy-saving of reheating furnace should pay attention to aspects such as energy-saving of heating variety steel,equality of heating steel,heating system,oxidation loss and so on.This will offer reference for energy-saving of domestic and overseas reheating furnace technology.

Analysis of Efflorescence of Castables in Walking Beam Reheating Furnace

When the castable refractory linings are installed without drying out sufficiently and exposed to high humidity for a long time,white fibrous or powdery substance appears on the surface,which is called“efflorescence”.The main reason is the cement of castable refractory linings contacts with C02 and moisture in the atmosphere to form calcium carbonate(CaC03).In general,efflorescence takes place more readily in lightweight castable refractories.In the walking beam reheating furnace construction project,there are many white powdery substances in the walking beams,because the construction procedure causes poor ventilation in the surrounding area,and the internal moisture of castable refractory linings cannot be evaporated effectively.In future,the project programming should consider the environmental humidity and surrounding ventilation.

Castables for Steel Rolling Reheating Furnace

1 Scope This standard specifies the classification, technical requirements, test methods, quality appraisal procedures, packing, marking, transportation, storage and quality certificate of castables for steel rolling reheating furnace.

A Novel MDFA-MKECA Method With Application to Industrial Batch Process Monitoring

For the complex batch process with characteristics of unequal batch data length,a novel data-driven batch process monitoring method is proposed based on mixed data features analysis and multi-way kernel entropy component analysis(MDFA-MKECA)in this paper.Combining the mechanistic knowledge,different mixed data features of each batch including statistical and thermodynamics entropy features,are extracted to finish data pre-processing.After that,MKECA is applied to reduce data dimensionality and finally establish a monitoring model.The proposed method is applied to a reheating furnace industry process,and the experimental results demonstrate that the MDFA-MKECA method can reduce the calculated amount and effectively provide on-line monitoring of the batch process.

Optimal control for spatial-temporal distributed nonlinear autoregressive with exogenous inputs correlation model of steel rolling reheating furnace: a coordinated time-sharing control approach

Accurate control of slab temperature and heating rate is an important significance to improve product performance and reduce carbon emissions for steel rolling reheating furnace(SRRF).Firstly,a spatial temporal distributed-nonlinear autoregressive with exogenous inputs correlation model(STD-NARXCM)to spatial temporal distributed-autoregressive with exogenous inputs correlation model(STD-ARXCM)in working point is established.Secondly,a new coordinated time-sharing control architecture in different time periods is proposed,which is along the length of the SRRF to improve the control performance.Thirdly,a hybrid control algorithm of expert-fuzzy is proposed to improve the dynamic of the temperature and the heating rate during time period 0 to t_(1).A hybrid control algorithm of expert-fuzzy-PID is proposed to enhance the control accuracy and the heating rate during time period t_(1) to t_(2).A hybrid control algorithm of expert-active disturbance rejection control(ADRC)is proposed to boost the anti-interference and the heating rate during time period t_(2) to t_(3).Finally,the experimental results show that the coordinated time-sharing algorithm can meet the process requirements,the maximum deviation of temperature value is 8-13.5℃.

Thermal insulation constructal optimization for steel rolling reheating furnace wall based on entransy dissipation extremum principle

Analogizing with the heat conduction process, the entransy dissipation extremum principle for thermal insulation process can be described as: for a fixed boundary heat flux (heat loss) with certain constraints, the thermal insulation process is optimized when the entransy dissipation is maximized (maximum average temperature difference), while for a fixed boundary temperature, the thermal insulation process is optimized when the entransy dissipation is minimized (minimum average heat loss rate). Based on the constructal theory, the constructal optimizations of a single plane and cylindrical insulation layers as well as multi-layer insulation layers of the steel rolling reheating furnace walls are carried out for the fixed boundary temperatures and by taking the minimization of entransy dissipation rate as optimization objective. The optimal constructs of these three kinds of insulation structures with distributed thicknesses are obtained. The results show that compared with the insulation layers with uniform thicknesses and the optimal constructs of the insulation layers obtained by minimum heat loss rate, the optimal constructs of the insulation layers obtained by minimum entransy dissipation rate are obviously different from those of the former two insulation layers; the optimal constructs of the insulation layers obtained by minimum entransy dissipation rate can effectively reduce the average heat loss rates of the insulation layers, and can help to improve their global thermal insulation performances. The entransy dissipation extremum principle is applied to the constructal optimizations of insulation systems, which will help to extend the application range of the entransy dissipation extremum principle.

Heat Transfer and Energy Analysis of a Pusher Type Reheating Furnace Using Oxygen Enhanced Air for Combustion

Oxy-fuel firing is more energy efficient and environmental friendly than conventional air-fuel firing and its application to reheating furnaces has begun since 1990s. A computational method was presented to predict the steady heat transfer to the billets and temperature distribution in a continuous pusher type reheating furnace in which combustion air was enhanced by oxygen. Radiation heat flux calculated from the radiation heat exchange within the furnace was modeled using the FVM considering the effects of furnace walls and billets. Energy consumption per ton of steel, production rate and thermal efficiency of furnace, and trend of NOx emission in various levels of oxygen enrichment were investigated by comparing with baseline furnace （21% of O2 in air）. The results showed that the best range of oxygen enrichments was between 21% and 45% by volume, as the higher slope of flame temperature and production increase occur in this range. The reduction of energy consumption can be obtained up to 18% per ton of steel for oxygen enrichment of 60 % by volume.

Inverse Estimation of Transient Heat Flux to Slab Surface

The transient heat flux was calculated using a model for inverse heat conduction problems based on temper- ature measurements. The unknown heat flux was taken as an optimization variable and solved by minimizing the differences between the calculated temperatures and the measured ones. Several examples were given to show the ef- fectiveness and the accuracy of the inverse algorithm in estimating the transient heat flux to a slab surface. The re sults show that the inverse approach can be applied in the steel industry or in other areas where the target of investi- gation is inaccessible to direct measurements or difficult to be directly modeled.