Centrifuge model tests on pile-reinforced slopes subjected to drawdown

Piles are generally an effective way to reduce the risk of slope failure.However,previous approaches for slope stability analysis did not consider the effect of the piles coupled with the decrease of the water level(drawdown).In this study,a series of centrifuge model tests was performed to understand the deformation and failure characteristics of slopes reinforced with various pile layouts.In the centrifuge model tests,the pile-reinforced slopes exhibited two typical failure modes under drawdown conditions:across-pile failure and through-pile failure.In the through-pile slope failure,a discontinuous slip surface was observed,implying that the assumption of the slip surface in previous stability analysis methods was unreasonable.The test results showed that drawdown led to instability of the piles in cohesive soil,as the saturated cohesive soil failed to provide sufficient constraint for piles.The slope exhibited progressive failure,from top to bottom,during drawdown.The deformation of the piles was reduced by increasing the embedment depth and row number of piles.In addition,the deformation of soils outside the piles was influenced by the piles and showed a similar distribution shape as the piles,and the similarity degree weakened as the distance from the piles increased.This study also found that the failure mechanism of unreinforced and pile-reinforced slopes induced by drawdown could be described by coupling between the deformation localization and local failure,and it revealed that pile-reinforced slopes could reduce slope deformation localization during drawdown.

Pile-soil stress ratio in bidirectionally reinforced composite ground by considering soil arching effect

To discuss the soil arching effect on the load transferring model and sharing ratios by the piles and inter-pile subsoil in the bidirectionally reinforced composite ground, the forming mechanism, mechanical behavior and its effect factors were discussed in detail. Then, the unified strength theory was introduced to set up the elastoplastic equilibrium differential equation of the subsoil under the limit equilibrium state. And from the equation, the solutions were derived with the corresponding formulas presented to calculate the earth pressure over and beneath the horizontal reinforced cushion or pillow, the stress of inter-pile subsoil and the pile-soil stress ratio. Based on the obtained solutions and measured data from an engineering project, the influence rules by the soil property parameters (i.e., the cohesion c and internal friction angle φ) and pile spacing on the pile-soil stress ratio n were discussed respectively. The results show that to improve the load sharing ratio by the piles, the more effective means for filling materials with a larger value of φ is to increase the ratio of pile cap size to spacing, while to reduce the pile spacing properly and increase the value of cohesion c is advisable for those filling materials with a smaller value of φ.

Study on Interface mechanical behavior of steel tube reinforced concrete composite pile

Currently for the steel tube reinforced concrete composite pile research, although predecessors make a comprehensive research on the composite pile beating performance, design technology, but there are still many problems have not been solved, such as the steel tube reinforced concrete pile composite interracial force learn performance research is still in the initial stage. In this paper, we mainly discuss the research methods of several interface mechanical properties and propose the possibility of studying the mechanical properties of the steel tube reinforced concrete composite pile by using the principle of ultrasonic speckle.

Flexure-Compression Testing of Bridge Timber Piles Retrofitted with Fiber Reinforced Polymers

The adequacy of using Fiber Reinforced Polymer (FRP) retrofit technique to restore the flexure-compression behavior of deteriorated bridge timber piles is examined experimentally in this paper. Sixteen specimens are tested monotonically under eccentric compressive loading. The specimens are first tested in their unretrofitted condition to determine their elastic properties. Each specimen is then cut and connected (posted) using the proposed FRP retrofit technique, and retested. The results show that the retrofitted specimens are capable of reaching same or higher strengths than that of the unretrofitted specimens with minimal reduction in their stiffness. Based on the experimental results, a design equation is presented to compute the volumetric ratio of FRP needed for retrofitting bridge timber piles under eccentric load.

Quantitative analysis of magnetic anomaly of reinforcements in bored in-situ concrete piles

We quantitatively study magnetic anomalies of reinforcement rods in bored insitu concrete piles for the first time and summarized their magnetic anomaly character. Key factors such as measuring borehole orientation, borehole-reinforcement distance, and multiple-section reinforcement rods are discussed which contributes valid and quantitative reference for using the magnetic method to detect reinforcement rods. Through tests with model piles, we confirm the accuracy of theoretical computations and then utilize the law discovered in theoretical computations to explain the characteristics of the actual testing curves. The results show that the Za curves of the reinforcement rod reflect important factors regarding the reinforcement rods, such as rod length, change of reinforcement ratio, length of overlap, and etc. This research perfects the magnetic method for detecting reinforcement rods in bored in-situ concrete piles and the method has great importance for preventing building contractor fraud.

Experimental Study of Dynamic Characteristics on Composite Foundation with CFG Long Pile and Rammed Cement-Soil Short Pile

Based on the idea of optimization design of pile type, the two kinds of the typical pile type are selected, which containing flexibility pile (e.g. rammed cement-soil pile is for short RCSP), and rigid pile (e.g. cement-flyash-gravel pile is for short CFGP). The three kinds of the composite foundation are designed, which are CFGP, CFG long pile and CFG short pile (for short CFGLP-CFGSP), CFG long-short pile and rammed cement-soil short pile (for short CFGLP-RCSSP). Natural earthquake is simulated by using the engineering blasting;the dynamic characteristics and dynamic response of the composite foundation are studied through field test. CFGLP-RCSSP is closed to linear relation. The bearing capacity of the four composite foundation of the CFGP, CFGLP-CFGSP, and CFGLP-RCSSP in the site are 225 kPa, 179 kPa, and 197 kPa, separately increases 150%, 98.8% and 119% compared to the natural foundation. The vibration main frequency is mainly depended on properties of foundation soil and piles between vibration source and measuring point, pilling load value. Horizontal vibration main frequency greater than the vertical vibration main frequency and the vertical vibration main frequency close to the first-order natural frequency of composite foundation. With the pilling load increasing, the CFGLP-RCSSP pile composite foundation combined frequency decreased. Under the same blast energy, the acceleration peak on the CFG pile composite foundation is less than CFGLP-CFGSP the corresponding values, as the load increases, the peak acceleration gently. CFG pile composite foundation is favorable on seismic. The distribution of peak acceleration is consistent within 4 m from pile top in the CFGLP_RCSSP composite foundation. The maximum of the horizontal acceleration peak along the pile body occurs at a distance of pile top 4 m or the pile top, and that of vertical acceleration peak occurred at a pile top.

High-Rise Residential Reinforced Concrete Building Optimisation

In the last few decades structure optimisation has become a main task in a civil engineering project. As a matter of fact, due to the complexity and particularity of every structure, the great amount of variables and design criteria to considerate and many other factors, a general optimisation’s method is not simple to formulate. As a result, this paper focuses on how to provide a successful optimisation method for a particular building type, high-rise reinforced concrete buildings. The optimization method is based on decomposition of the main structure into substructures: floor system, vertical load resisting system, lateral load resisting system and foundation system;then each of the subsystems using the design criteria established at the building codes is improved. Due to the effect of the superstructure optimisation on the foundation system, vertical and lateral load resisting system is the last to be considered after the improvement of floor. Finally, as a case example, using the method explained in the paper, a 30-story-high high-rise residential building complex is analysed and optimised, achieving good results in terms of structural behaviour and diminishing the overall cost of the structure.

Numerical modelling for predicting corrosion initiation life of reinforced concrete square piles under reverse-seepage pressure

Square piles of reinforced concrete(RC)in marine environments are susceptible to chloride-inducedcorrosion.A novel reverse-seepage technique(RST)is applied to square piles to block the intrusion of chlorides.Thisresearch introduces a computational model designed to predict the lifespan of corrosion initiation in reinforced concretesquare piles when applied reverse-seepage pressure.The model considers the impacts of chloride binding and the tripletime-dependence property among the permeability,the corrected surface chloride concentration,and the diffusioncoefficient.The proposed numerical model is solved using the alternating direction implicit(ADI)approach,and itsaccuracy and reliability are evaluated by contrasting the computational outcomes with the analytical solution andexperimental results.Furthermore,the primary factors contributing to the corrosion of reinforced concrete square pilesare analyzed.The results indicate that applying RST can decrease the chloride penetration depth and prolong the lifespanof corrosion initiation in square piles.The water-cement ratio and reverse seepage pressure are the most influentialfactors.A water pressure of 0.4 MPa can double the life of concrete,and the durable life of concrete with a water-cementratio of 0.3 can reach 100 years.

Erective Sea Embankment with PCC Piles

The sea embankment is a critical civil works in marine and coastal engineering. In this study, an innovative technique is proposed for constructing erective sea embankments. In the construction of sea embankments, this technique integrates PCC pile installation, PVDs drainage systems, and geotextile reinforcements, resulting in sea embankments with PCC piles. In the application of a sea embankment with PCC piles, PCC piles are employed as the retaining structures; the soft sea ground inside PCC piles is drained and improved by PVDs and vacuum-surcharge combined preloading; geotextile-reinforced backfills lying over the improved soft ground form the embankment body. Brief descriptions of the fundamentals, design and construction of the sea embankment with PCC piles are presented. A case study on the stability of sea embankment with PCC piles is presented as well.

The Dynamic Characteristic Experimental Method on the Composite Foundation with Rigid-Flexible Compound Piles

Based on the idea of optimization design of pile type, the composite foundations, which include cememt-flyash-gaavel (for short CFG) long piles and cement-soil (for short CS) short piles, and CS piles with CFG core as well, are formed. The method of the site dynamic characteristic tests of the composite foundations is discussed. The test results show that fireworks bomb may replace demolitions as the vibration resource. Vibration time is about 0.1 sec. Horizontal vibration major frequency is at 22.476 - 56.436 Hz, and vertical vibration major frequency is at 15.538 - 55.884 Hz. The pile arrangements of the composite foundation in the same site have more effect on the acceleration peak value. From the point of vibration, the anti-seismic effect of the CS piles with CFG core is better than others.

Field study of plastic tube cast-in-place concrete pile

The compositions, technical principles and construction equipments of a new piling method used for ground improvement plastic tube cast-in-place concrete pile were introduced. The results from static load tests on single piles with different forms of pile shoes and on their composite foundations were analyzed. The distribution patterns of axial force, shaft friction and toe resistance were studied based on the measurements taken from buried strain gauges. From the point of engineering application, the pile has merits in convenient quality control, high bearing capacity and reliable quality, showing higher reasonability, advancement and suitability than other ground improvement methods. The pile can be adopted properly to take place of ordinary ground improvement method, achieving greater economical and social benefits.

Application of CFG Pile Construction Technology for Soft Foundation Treatment

CFG pile has been widely applied as one of the common ground treatment techniques. As a concealed work, the construction quality of pile foundation not only relates to the success of the project, but also concerns the benefits of thousands of hot, seholds. Only strengthening the supervision and management during the construction and strictly designing and specifying CFG pile can ensure the construction quality of CFG pile. But most researches focus on operating mechanism and theoretical analysis, and there are fewer researches about the construction of CFG pile. The real construction of CFG pile has no specified operation and lacks of the construction guidance, which not only causes great problems and has great influence on the intensity of CFG pile, but also makes the real pile body have great difference from the design requirements. Therefore, the study on construction of CFG pile in the paper has great significance.

温度与荷载共同作用下钢筋混凝土桩的细观损伤

为探究港口码头不同环境因素对码头桩身材料特性的劣化影响而降低桩身承载能力,通过颗粒流分析程序(particle flow code 3D,PFC3D)建立三维颗粒流离散元钢筋混凝土桩模型开展研究。对温度-应力模型进行建立,选取热学参数,构建了温度热管模型,通过分级加热,得到了钢筋混凝土桩的横向拉伸应变、纵向压缩应变以及微裂缝生长数量随温度变化曲线;调整模型混凝土粗骨料占比与强度等级,研究其对钢筋混凝土桩受热损伤的影响;通过施加温度场的模型进行水平加荷载后,得到的应力应变曲线;基于模型微裂隙数量的损伤变量,并构建了损伤变量-轴向应变曲线,进一步分析了温度-荷载共同作用的损伤规律。结果表明:混凝土轴向压缩应变和横向拉伸应变会随温度的增加而逐渐升高,细观微裂隙数量会随温度的升高而增长;粗骨料占比升高会使受热初始损伤增加;温度的升高,材料的宏观力学性能出现了不同程度的降低。

基于水平旋喷桩处置优化的地铁隧道施工变形控制分析

为研究富水砂层隧道中水平旋喷桩+超前小导管组合预加固的效果,以青岛地铁某区间段隧道为依托,采用有限元数值模拟方法,对比分析了无预加固、单独使用水平旋喷桩及旋喷桩配合超前小导管组合预加固三种工况的加固效果。结果表明,与无预加固方案相比,单独使用水平旋喷桩预加固可使地表沉降、拱顶沉降、掌子面纵向位移分别相应减少约61%、59%、38%;而水平旋喷桩与超前小导管组合预加固方案可使地表沉降、拱顶沉降、掌子面纵向位移分别相应减少约66%、77.6%、38.9%,典型开挖断面处与拱脚处地下水渗流量分别减少93.4%、96.7%,预加固效果与止水效果显著。

湿陷性黄土地基中桩基负摩阻力计算新方法

负摩阻力对湿陷性黄土地基中桩基的承载变形性状具有重要影响,现行桩基规范及黄土规范推荐的负摩阻力计算方法不能反映黄土桩基负摩阻力的实际性状。对近30年来在黄土地区开展的钢筋混凝土灌注桩现场浸水试验实测数据进行统计,分析黄土浸水完成后桩身中性点深度、桩身最大负摩阻力深度及负摩阻力系数与桩长径比的关系,通过线性拟合得到了中性点深度比、最大负摩阻力深度比及负摩阻力系数与桩长径比的经验表达式,提出湿陷性黄土地基中桩基负摩阻力计算的新方法。新方法用三角形表示负摩阻力沿深度的分布,能反映负摩阻力从桩顶向下先逐渐增大、达到最大值后随深度增加逐渐减小、最终在中性点处减小为零的分布特征。将提出的方法、桩基规范及黄土规范方法的计算结果与实测结果进行对比,结果表明,桩基规范预测的中性点深度比优于黄土规范,黄土规范预测的最大下拉荷载优于桩基规范,而用新方法计算的负摩阻力最接近实测结果。

浅埋偏压黄土隧道地表旋喷桩加固工艺参数研究

在黄土隧道修建过程中,其洞口段因浅埋偏压、围岩软弱破碎等通常需要进行加固处理。地表旋喷桩法具有适用范围广、加固效果好等优点,被广泛应用于隧道浅埋偏压段软弱围岩地表加固工程。以浅埋偏压黄土隧道进口段初期支护侵限为研究背景,介绍了现场地表旋喷桩加固的施工过程;建立了侵限段三维加固模型并分析了地表旋喷桩加固前后的变形控制效果,说明了处治措施的合理性;对比分析了现场监控量测结果,验证了数值模拟的准确性;开展了地表旋喷桩的工艺设计参数优化分析。结果表明:由于偏压作用,地表最大沉降值偏离隧道中心线,且拱顶中心线处沉降>右拱肩处沉降>左拱肩处沉降;施加地表旋喷桩对于减小地表沉降十分有效,地表最大沉降值减小了45.5%;采用地表旋喷桩加固处理后,拱顶处加固效果最为显著,较加固前沉降减小了57.9%,同时加固后左、右拱肩沉降差值减小了17.4%;建议隧道浅埋偏压段地表旋喷桩加固工艺设计参数:桩直径为0.4~0.6 m、桩间距为1.2 m、横向加固范围为1.5~2倍洞径、竖向加固范围为洞身两侧旋喷桩与隧道拱底平齐。

不均匀地层中刚性桩复合地基变形及加固措施分析

刚性桩复合地基凭借其工后沉降小、施工周期短、整体稳定性强、社会经济效益高等优势,逐渐得到广泛应用,但也伴随着一些工程问题,如在不均匀地层下刚性桩复合地基路堤容易出现稳定性问题。本文针对不均匀地层下刚性桩复合地基典型工程案例展开研究,采用有限元软件建立三维模型,揭示改进方案前后不均匀地层下刚性桩复合地基的变形规律,研究3种加固方式对于刚性桩复合地基稳定性的增强效果。结果表明:不均匀地层下刚性桩复合地基会产生偏应力进而引起路堤差异沉降,结构稳定性较差,改进方案可以有效降低路堤沉降,提高结构整体稳定性,横梁加固可以有效提高刚性桩复合地基的水平稳定性。

桩-浆联合模式下土遗址裂隙注浆加固机制

桩-浆联合修复土遗址裂隙加固效果显著,加固机制复杂尚待明晰。基于固体传热、非饱和渗透理论,结合生石灰非等温水化进程和桩-浆-土的动态变化关系,建立了该过程中水-热-力耦合的三维扩散模型并进行求解,通过现场注浆试验过程的实时监测结果与有限元模拟结果的比对以揭示其加固机制。结果一致表明:石灰桩和浆液中生石灰都在极短时间内达到较高的反应程度,60 min时反应程度分别达到87%和76%;裂隙周边夯土中各物理场均呈现出以浆液和石灰桩为中心,距离裂隙越远数值越低的分布规律;浆液和石灰桩中80%的水分和69%的水化热被有效用于加固过程;归一化处理后得到该过程中温度、水分、膨胀压力作用的有效影响范围分别为裂隙宽度的2.4倍、0.7倍和1.4倍。该研究为桩-浆联合修复土遗址裂隙新方法提供了理论支持。

基于混凝土水化热的灌注桩成桩质量评价方法及应用

针对如何基于灌注桩水化热温度场准确评价桩身质量的问题,利用与桩身横截面中心径向距离大于0.5倍桩半径范围内,混凝土水化热温度随径向距离的变化近似线性的特征,建立根据钢筋笼上对称两测点的水化热温度计算钢筋笼偏位的方法。结合缺陷灌注桩的水化热仿真分析,系统分析缺陷几何特征和热工参数变化对灌注桩水化热温度场的影响规律,提出根据沿钢筋笼主筋布置水化热温度测点获得的温度-深度曲线特征,判断缺陷存在并分析缺陷空间分布位置的方法。结合现场试验及与低应变、跨孔超声波检测结果的对比,验证了该方法的可行性。

双向增强复合地基桩土应力比计算方法研究

研究目的:桩土应力比是反映双向增强复合地基工作特性的重要指标。由于路堤荷载下双向增强复合地基承载变形机理复杂,本文以双桩范围内的路堤与双向复合地基为研究对象,考虑路堤土拱效应、加筋层网兜效应、应力扩散效应等多重效应的共同作用,建立路堤-水平加筋垫层-竖向桩体-桩间土协调变形的二维理论分析模型,探究各影响因素对桩土应力比的影响规律。研究结论:(1)桩土应力比随填土重度、桩间距的增加而减小,随填料内摩擦角的增大呈先增加后减小趋势,随路堤填筑高度、格栅层数、填料黏聚力的增加而增大;(2)桩土应力比对各参数的敏感性由高到低排序为:桩间距、路堤填筑高度、路堤填土重度、路堤填料黏聚力、格栅层数及路堤填料内摩擦角;(3)本研究成果可为类似工程的桩土应力比计算提供理论依据及工程借鉴。