Probabilistic Lifetime Assessment of Marine Reinforced Concrete with Steel Corrosion and Cover Cracking

In order to study the durability behavior of marine reinforced concrete structure suffering from chloride attack, the structural service life is assumed to be divided into three critical stages, which can be characterized by steel corrosion and cover cracking. For each stage, a calculated model used to predict the lifetime is developed. Based on the definition of durability limit state, a probabilistic lifetime model and its time-dependent reliability analytical method are proposed considering the random natures of influencing factors. Then, the probabilistic lifetime prediction models are applied to a bridge pier located in the Hangzhou Bay with Monte Carlo simulation. It is found that the time to corrosion initiation to follows a lognormal distribution, while that the time from corrosion initiation to cover cracking t~ and the time for crack to develop from hairline crack to a limit crack width t2 can be described by Weibull distributions. With the permitted failure probability of 5.0%, it is also observed that the structural durability lifetime mainly depends on the durability life to and that the percentage of participation of the life to to the total service life grows from 61.5% to 83.6% when the cover thickness increases from 40 mm to 80 mm. Therefore, for any part of the marine RC bridge, the lifetime predictions and maintenance efforts should also be directed toward controlling the stage of corrosion initiation induced by chloride ion.

Research on Bond-Slip Constitutive Relation for Steel Reinforced Concrete Members

The constitutive relation of bond-slip on steel and concrete interface is proposed for short steel reinforced concrete （SRC） column. Based on the experimental research on bond-slip performance, a mechanical model of short SRC column in pulling or pushing test is established. By means of the elasto-plasticity theory the explicit formulation of bond-slip constitutive relation τ-s in different anchor-hold place of push and pull member is investigated under the conditions of balance and boundary. The study shows that the constitutive relation is relevant to the embedment length and the thickness of concrete cover. The results are continuous descriptions of bond-slip constitutive relation and can be used to analyze the non-linear performance of SRC members. Results indicate that the principle of the method is correct and it performs well for short SRC column.

Study on Interface mechanical behavior of steel tube reinforced concrete composite pile

Currently for the steel tube reinforced concrete composite pile research, although predecessors make a comprehensive research on the composite pile beating performance, design technology, but there are still many problems have not been solved, such as the steel tube reinforced concrete pile composite interracial force learn performance research is still in the initial stage. In this paper, we mainly discuss the research methods of several interface mechanical properties and propose the possibility of studying the mechanical properties of the steel tube reinforced concrete composite pile by using the principle of ultrasonic speckle.

Concrete-Filled Steel Tube Arch Bridges in China

In the past 20 years, great progress has been achieved in China in the construction of concrete-filled steel tube （CFST） arch bridges and concrete arch bridges with a CFST skeleton. The span of these bridges has been increasing rapidly, which is rare in the history of bridge development. The large-scale construction of expressways and high-speed railways demands the development of long-span arch bridges, and advances in design and construction techniques have made it possible to construct such bridges. In the present study, the current status, development, and major innovative technologies of CFST arch bridges and concrete arch bridges with a CFST skeleton in China are elaborated. This paper covers the key con- struction technologies of CFST arch bridges, such as the design, manufacture, and installation of steel tube arch trusses, the preparation and pouring of in-tube concrete, and the construction of the world＇s longest CFST arch bridge-the First Hejiang Yangtze River Bridge. The main construction technologies of rein- forced concrete arch bridges are also presented, which include cable-stayed fastening-hanging cantilever assembly, adjusting the load by means of stay cables, surrounding the concrete for arch rib pouring, and so forth. In addition, the construction of two CFST skeleton concrete arch bridges-the Guangxi Yongning Yong River Bridge and the Yunnan-Guangxi Railway Nanpan River Bridge--is discussed. CFST arch bridges in China have already gained a world-leading position; with the continuous innovation of key technologies, China will become the new leader in promoting the development of arch bridges.

Axial Bearing Capacity of Short FRP Confined Concrete-filled Steel Tubular Columns

The bearing capacity of FRP confined concrete-filled steel tubular （FRP-CFST） columns under axial compression was investigated. This new type of composite column is a concrete-filled steel tube （CFST） confined with fiber-reinforced polymer （FRP） wraps. Totally 11 short column specimens were tested to failure under axial compression. The influences of the type and quantity of FRP, the thickness of steel tube and the concrete strength were studied. It was found that the bearing capacity of short FRP-CFST column was much higher than that of comparable CFST column. Furthermore, the formulas for calculating the bearing capacity of the FRP-CFST columns are proposed. The analytical calculated results agree well with the experimental results.

乌兹别克斯坦9度区某超高层建筑结构设计与优化

对于9度设防地区的超高层建筑,其结构设计基本由地震作用控制,因此抗震设计尤为重要。建筑消能减震技术可在提高结构地震安全储备的同时,降低整体工程造价,是结构优化设计的有效措施。对位于9度区的超高层建筑进行了结构方案选型对比、结构方案优化、减震设计方案比选、剪力墙内嵌钢板优化。结果显示,钢骨混凝土框架⁃核心筒方案相对于钢框架⁃支撑方案具备更高的成本优势;框架⁃核心筒方案可通过精细化设计作进一步优化;在此基础上,对钢骨混凝土框架⁃核心筒方案采用两种消能减震方案进行比选,结果表明,采用黏滞阻尼器方案的结构抗震性能明显优于采用黏滞阻尼墙方案;最后通过增大剪力墙竖向分布钢筋配筋率,对低区核心筒墙肢中的内嵌钢板进行了优化。

反复荷载下圆钢管型钢再生混凝土组合柱恢复力模型研究

为建立圆钢管型钢再生混凝土组合柱的恢复力模型,对11根圆钢管型钢再生混凝土组合柱试件进行了低周反复荷载试验研究,考虑了再生骨料取代率、配钢率及钢管径厚比等不同设计参数的影响,分析了组合柱的地震破坏形态及滞回性能。基于组合柱的力学特征及曲线形状,提出了圆钢管型钢再生混凝土组合柱骨架曲线的三折线参数模型,采用理论推导与数据拟合的方法确定了组合柱骨架曲线的模型参数。在此基础上,给出了组合柱的滞回规则和卸载规律,构建了组合柱的恢复力模型,计算滞回曲线与试验滞回曲线吻合良好,表明该恢复力模型较好地反映了反复荷载下组合柱的受力特征点及滞回性能,可为此类组合柱的推广提供技术参考。

设有叠合柱的局部错层RC框架结构地震易损性分析

为研究某一设有叠合柱的局部错层钢筋混凝土(reinforced concrete,RC)框架结构在近断层和远场地震作用下的破坏概率,自定义钢管混凝土叠合柱塑性铰参数,并与试验对比验证塑性铰参数的有效性。采用SAP2000建立非线性分析模型,选取近断层和远场地震波共22条,分别以地震峰值加速度(peak ground acceleration,PGA)和最大层间位移角作为地震动强度指标和结构性能指标,基于增量动力分析(incremental dynamic analysis,IDA)结果和点估计函数对错层框架结构进行易损性分析。结果表明:对于远场地震动,结构满足“三水准”抗震设防要求,在罕遇地震下超越防止倒塌极限状态的概率仅为0.24%;结构在近断层多遇地震下仍能满足“小震不坏”的设计要求,设防地震下结构超越修复后使用极限状态的概率为53.63%,发生中等破坏的概率较大,罕遇地震下结构达到倒塌极限状态的概率为5.37%,较远场地震作用破坏更为严重。研究结果可为错层框架结构的设计和地震风险评估提供参考。

圆钢管型钢再生混凝土组合柱滞回性能非线性有限元分析

基于圆钢管型钢再生混凝土组合柱低周反复荷载试验研究,采用OpenSees软件对该组合柱进行了滞回性能数值分析,获取了组合柱的滞回曲线及抗震性能指标,并与试验结果进行了比较,验证了组合柱数值模型的合理性。在此基础上,对组合柱的滞回性能开展了参数影响分析。结果表明:再生骨料取代率从0增大到100%,组合柱的峰值荷载下降了7.78%,延性略有降低;提高再生混凝土强度、型钢强度及圆钢管强度,对于提升组合柱的承载力及刚度是有利的,但却使组合柱的脆性增大;随着轴压比的增大,组合柱的承载力呈现先上升后下降的趋势,而延性逐渐变差;型钢配钢率从5.54%增至9.99%,组合柱的峰值荷载提高了24.34%,但对于改善组合柱的延性不明显;增大钢管壁厚对组合柱的承载力和延性均是有利的。

内置型钢增强钢管约束钢筋混凝土柱节点抗震性能研究

采用钢管对传统RC柱进行约束,形成的钢管约束钢筋混凝土(STRC)柱具有优越的承载能力和耗能性能。但在应用于框架节点设计时,节点区域仍采用普通RC柱节点构造,可能导致节点处没有钢管约束而成为薄弱点,节点处易发生破坏。针对钢管约束钢筋混凝土(STRC)柱节点抗震性能薄弱的现状,提出采用内置型钢短柱进行增强。基于ABAQUS工作平台对具有相同构造形式的节点试件建立有限元模型,将数值计算所得破坏形态、滞回曲线和型钢应力与试验结果进行对比,两者吻合较好,在此基础上探讨内置型钢长度和轴压比对节点抗震性能的影响。结果表明:随着内置型钢长度增加,试件的承载力、极限位移和延性均有不同程度的提升,轴压比对试件受力性能影响较小。通过进一步分析试件的破坏机制、型钢抗弯性能和耗能能力,提出满足节点抗震性能需求的内置型钢长度建议取值。

侧向冲击荷载作用下CFRP型材-方钢管混凝土柱的动力响应

为了研究CFRP型材-方钢管混凝土固简柱的抗侧向冲击性能,采用水平撞击装置对3个CFRP型材-方钢管混凝土柱进行侧向冲击试验.根据柱的破坏模式、局部变形、整体变形及冲击力分析柱的动力响应,研究了CFRP型材、边界条件、冲击能量与冲击冲量对试件动力响应的影响规律.结果表明,CFRP型材-方钢管混凝土固简柱呈现弯曲破坏,具有良好的抗冲击性能,且随着支座约束能力的增大,抗侧向冲击性能增大.增加单位冲击冲量可使悬臂试件的峰值位移下降7%,而两端固支试件峰值位移仅变化1%.随着支座约束能力的下降,冲击冲量对试件变形的影响程度增大.在钢管混凝土固简试件中内置CFRP型材可使冲击位置处峰值位移下降9%,且降低程度随着支座约束能力的下降而增加.

圆钢管型钢再生混凝土组合柱水平承载力计算方法研究

通过对11个圆钢管型钢再生混凝土组合柱进行低周反复荷载试验,分析再生粗骨料取代率、型钢截面形式、轴压比、型钢配钢率及圆钢管壁厚参数对组合柱水平承载力的影响规律;观察了组合柱的破坏形态及特征,研究了圆钢管、型钢翼缘及腹板应变的发展规律,分析了组合柱的地震破坏特征。研究表明,在水平地震作用下组合柱发生典型的压弯塑性铰破坏。在此基础上,结合现有规范提出了基于叠加原理的圆钢管型钢再生混凝土组合柱水平承载力计算方法。计算结果表明,其水平承载力计算值与试验值吻合度较好,能较为准确地预测组合柱的水平承载力。

局部环向变厚度方钢管混凝土柱偏压力学性能研究

针对海洋环境中飞溅区造成的钢管混凝土柱局部环向腐蚀现象,采用机械削减方式模拟钢管壁厚局部环向腐蚀,进行了7个方钢管混凝土柱偏压试验,揭示了削弱率和偏心率对其偏压承载力的影响,并通过数值模拟对削弱率进行拓展分析.提出了基于削弱率的偏压承载力降低系数,代入中、美规范进行偏压承载力计算.结果表明:钢管的局部环向变厚度严重削弱了方钢管混凝土柱的偏压承载力和侧向挠曲能力;较大的加载偏心率也降低了其偏压承载力,但增大了其侧向挠曲能力.引入偏压承载力降低系数后,根据中、美规范计算得到的偏压承载力与试验值均吻合较好;相比于我国规范,美国规范在计算偏压承载力时相对更加保守.

配筋空心方钢管高强混凝土纯弯构件受力性能有限元分析

目的 研究配筋空心钢管高强混凝土构件的抗弯性能,推动其在建筑结构中的应用。方法 采用有限元分析软件ABAQUS建立配筋空心钢管混凝土构件有限元模型,在验证模型准确的基础上,分析构件的受力全过程及钢材屈服强度、混凝土抗压强度、钢管壁厚、钢筋直径、普通钢筋数量对构件受弯性能的影响。结果 纯弯试件在荷载作用下受力过程可分为3个阶段:弹性阶段、弹塑性阶段和强化阶段;试件破坏形态均为受弯破坏,表现出较好地延性。结论 组合构件在弯矩作用下可以很好地协同工作;钢材屈服强度和钢管壁厚的增加对构件承载力的提高影响最显著,建议配置普通钢筋数量在6~8根为最优。

铅黏弹性阻尼器增强钢管约束钢筋混凝土柱节点抗震性能研究

针对钢管约束钢筋混凝土(steel tubed reinforced concrete,STRC)柱节点抗震性能薄弱的现状,提出采用改良的铅黏弹性阻尼器进行增强。基于ABAQUS工作平台对铅黏弹性阻尼器试件建立有限元模型,将数值计算所得滞回和骨架曲线、耗能性能及疲劳性能与试验结果进行对比,两者吻合较好。在此基础上探讨了铅芯直径、铅芯布置形式及复合黏弹性体厚度比值对铅黏弹性阻尼器力学性能的影响。结果表明:相较于扇形铅黏弹性阻尼器,改良后的四边形铅黏弹性阻尼器表现出更好的力学性能;随着铅芯直径的增大,阻尼器的耗能能力指标均得到大幅提高;建议铅芯个数取2个,铅芯面积与复合黏弹性层面积比值取6%~8%,复合黏弹性体厚度比值约为0.67。建立不同布置方案的铅黏弹性阻尼器增强STRC柱节点试件模型,对其破坏形态、滞回特性和箍筋应力进行对比分析,给出合理的布置方案,为实际工程提供参考。

配筋空心圆钢管高强混凝土轴压短柱工作机理分析

目的 提出一种配筋空心圆钢管高强混凝土新型组合柱,分析其在轴向荷载作用下的工作机理,以解决空心钢管混凝土柱空心率较大和延性差等问题。方法 对配筋空心圆钢管高强混凝土短柱进行轴压试验,利用ABAQUS有限元分析软件建立组合柱的有限元模型,以试验结果验证有限元模型的准确性。对组合柱的受力工作机理进行分析,重点研究其在轴向荷载作用下的受力过程、各组分分担内力比例和应力状态。结果 与空心圆钢管高强混凝土柱相比,未配置普通钢筋的试件峰值承载力提升了6.37%、DI提高了6.64%、SI提高了3.59%,配置普通钢筋的试件峰值承载力提升了13.31%、DI提高了8.12%、SI提高了5.68%。整个受力过程中,管柱混凝土和夹层混凝土承载的内力比例分别为36.2%~39.7%和29.0%~30.6%。结论 配置普通钢筋的试件具有更高的承载能力和延性能力;夹层混凝土和管柱混凝土在加载过程中为主要受力组分;钢筋在加载前期基本不承担内力,进入塑性强化阶段才开始发挥作用。

含钢率对GFRP管-钢骨混凝土组合构件抗冲击性能的影响

为了研究含钢率对GFRP(glass fiber reinforced polymer)管-钢骨混凝土组合构件抗冲击性能的影响,建立15个组合构件的数值模型,在验证模型正确的基础上,通过分析典型构件的冲击全过程、截面弯矩发展以及破坏时应变分布规律,研究构件在侧向冲击荷载作用下的破坏模式;通过分析构件冲击力时程曲线、侧移时程曲线以及能量变化情况,探究含钢率对不同长细比构件抗冲击性能的影响。结果表明:与未配置钢骨的构件相比,GFRP管-钢骨混凝土构件的抗冲击承载力提高了7%~134%,侧向位移减小了13%~68%。在侧向冲击荷载作用下,构件的破坏模式以弯曲破坏为主,同时伴随着GFRP管和混凝土冲击区域的局部破坏,抗弯刚度是影响构件抗冲击性能的主要因素之一。构件的抗冲击承载力随着含钢率的增高而提高,随着构件长细比的增大而降低。含钢率相差1.5%时,截面惯性矩较大的窄翼缘型钢对构件的抗冲击性能更有利。对于长细比大于20的构件,钢骨耗能是组合构件总能耗的主要组成部分。

内置型钢的圆形不锈钢管混凝土构件的抗弯性能

采用有限元模型研究内置型钢的圆形不锈钢管混凝土构件的纯弯力学性能,有限元计算结果与试验结果吻合良好。该类典型构件的抗弯承载力比不锈钢管混凝土对比构件的相应值高111.33%;混凝土承担的弯矩也比对比构件的相应值高23.31%,受压区混凝土的抗压承载力约提高了20%,原因是钢管和型钢翼缘对受压区混凝土形成了良好的约束作用。该类构件的抗弯刚度与抗弯承载力随着混凝土强度、不锈钢含钢率、型钢含钢率和回转半径比的增大而提高;其抗弯承载力随着不锈钢屈服强度或型钢屈服强度的增大而提高。最终给出了该类构件的抗弯刚度和抗弯承载力的简化计算方法。

钢管约束钢筋混凝土柱梁节点研究现状与分析进展

钢管约束钢筋混凝土(steel tube-constrained reinforced concrete,STRC)柱具有优越的力学性能,但当STRC柱应用于框架结构时,常存在难以满足“强节点、弱构件”抗震设计要求的问题。为改善STRC柱梁节点的抗震性能,总结归纳了目前STRC柱梁节点的构造形式及增强机理,从工作机理、增强效果、易施工性等方面对各种构造形式的节点进行对比,认为复合式节点是解决STRC柱框架节点薄弱问题的最优途径。并进一步分析了不同构造形式STRC柱节点的轴压性能、抗震性能和理论设计方法,结果表明环梁对节点轴压承载力提升显著,钢管约束式节点轴压和抗震性能均表现良好,且设计理论较为成熟。最后,在试验研究和理论分析基础上,剖析了该研究领域亟需解决的问题和研究发展方向。

反复荷载下圆钢管型钢再生混凝土组合柱耗能能力及延性分析

对11个圆钢管型钢再生混凝土组合柱试件进行了低周反复荷载试验,观察了组合柱的破坏形态及特征,获取了组合柱的滞回曲线、等效粘滞阻尼系数、延性系数及侧向位移角等性能指标,分析了再生粗骨料取代率、型钢截面形式、轴压比、型钢配钢率和圆钢管径厚比等参数对组合柱耗能能力及延性的影响规律。结果表明:反复荷载作用下组合柱呈压弯塑性铰破坏模式;组合柱的荷载-位移滞回曲线饱满呈纺梭形,屈服位移后的等效粘滞阻尼系数在0.30~0.48之间,平均位移延性系数大于3.0,极限侧向位移角介于1/30~1/20之间且均大于规范限值1/50,组合柱表现出良好的耗能能力和延性。此外,组合柱的耗能能力和延性受再生粗骨料取代率的影响较大,全再生混凝土较普通混凝土耗能能力下降14.5%;增加钢管壁厚或型钢配钢率有利于提升组合柱的耗能能力和延性,而增大轴压比则对组合柱的延性和变形不利;内置型钢采用箱型截面时,组合柱耗能及延性最优,与工字型钢相比,采用箱型截面型钢的组合柱耗能能力和延性分别提升了23.5%和51.9%。