Use of stainless reinforcing steel (SRS) in reinforced concrete (RC) structures is a promising solution to corrosion issues. However, for SRS to be used in seismic applications, several mechanical properties need ...Use of stainless reinforcing steel (SRS) in reinforced concrete (RC) structures is a promising solution to corrosion issues. However, for SRS to be used in seismic applications, several mechanical properties need to be investigated. These include specified and actual yield strengths, tensile strengths, uniform elongations and low-cycle fatigue behavior. Three types of SRSs (Talley S24100, Talley 316LN and Talley 2205) were tested and the results are reported in this paper. They were compared with the properties of A706 carbon reinforcing steel (RS), which is typical for seismic applications, and MMFX II, which is a high strength, corrosion resistant RS. Low-cycle fatigue tests of the RS coupons were conducted under strain control with constant amplitude to obtain strain life models of the steels. Test results show that the SRSs have slightly lower moduli of elasticity, higher uniform elongations before necking, and better low-cycle fatigue performance than A706 and MMFX II. All five types of RSs tested satisfy the requirements of the ACI 318 code on the lower limit of the tensile to yield strength ratio. Except Talley 2205, the other four types of RSs investigated meet the ACI 318 requirement that the actual yield strength does not exceed the specified yield strength by more than 18 ksi (124 MPa). Among the three types of SRSs tested, Talley S24100 possesses the highest uniform elongation before necking, and the best low-cycle fatigue performance.展开更多
Electrochemical techniques of the corrosion measurements of reinforcing steeI in concrete have been evaluated. These techniques include half-cell potential measurements, impressed voltage method, impressed current met...Electrochemical techniques of the corrosion measurements of reinforcing steeI in concrete have been evaluated. These techniques include half-cell potential measurements, impressed voltage method, impressed current method and potentiostatic polarization technique. The results of corrosion behaviour of the steel in both 5%NaCl and 5%MgSO4 show that each electrochemical technique provides some information about the condition of the steel bar or the corrosivity of the environment being evaluated, yet none provides a complete data regarding the corrosion resistance of reinforcing steel in aggressive media展开更多
The mechanical and physical properties of concrete specimens obtained from replacing natural coarse aggregate with waste vehi- cle rubber tires at levels of 2vol%, 5vol%, 7vol%, and 10vol% were studied, and the corros...The mechanical and physical properties of concrete specimens obtained from replacing natural coarse aggregate with waste vehi- cle rubber tires at levels of 2vol%, 5vol%, 7vol%, and 10vol% were studied, and the corrosion behavior of reinforcing steels was investigated in these specimens. Corrosion rates were determined by measuring the galvanic current between steel-reinforced concrete specimens both with and without chloride addition. The change in electrode potential of reinforcing steels in these concrete specimens was measured daily for a period of 60 d in accordance with the testing method in ASTM C876. The results show that the use of waste vehicle tires in concrete instead of coarse aggregate decreases the mechanical strength of the specimens, and increases the corrosion rates of the reinforcing steels embedded in the concretes.展开更多
Reinforcement corrosion is the major cause of damage and early failure of reinforced concrete structures worldwide with subsequent enormous costs for maintenance, restoration and replacement. Many methods used today f...Reinforcement corrosion is the major cause of damage and early failure of reinforced concrete structures worldwide with subsequent enormous costs for maintenance, restoration and replacement. Many methods used today for assessment of reinforcement corrosion are based on electrochemical techniques that determine the free corrosion potential or polarization resistance. Most of these methods always consider the B value in Stern-Geary equation as constant. However, B changes with different condition. In this paper, potentialdynamic method is used to characterize the corrosion of reinforcing steel. The corrosion rate of Q235 carbon steel is measured with concrete environment. B is calculated real-time. By this way, the error of reinforcement corrosion rate is minimized.展开更多
The use of a natural white juice, taken from magrabe banana stem, as concrete admixture to improve mechanical and physicrvchemical properties of concrete has been studied. The compressive strength, bulk density the fr...The use of a natural white juice, taken from magrabe banana stem, as concrete admixture to improve mechanical and physicrvchemical properties of concrete has been studied. The compressive strength, bulk density the free lime liberated during hydration and the combined water content were determined. The results indicate that the admixture acts as a retarder in most cases and as accelerator in some ones. Also, the admixture effect on the corrosion resistance of the reinforcing steel against surrounding aggressive media has been investigated using galvanostatic polarization technique. The addition of 0.2% admixture leads to the more inhibition of the steel展开更多
Corrosion and electrochemical behaviour of reinforcing steel embedded in cement pastes with and without concrete admixtures used in Egypt to modify concrete properties have been studied. The influence of the admixtur...Corrosion and electrochemical behaviour of reinforcing steel embedded in cement pastes with and without concrete admixtures used in Egypt to modify concrete properties have been studied. The influence of the admixtures on the corrosion resistance of the steel against chloride attack has been studied by using impressed current and impressed voltage techniques. The results indicate that the type and concentration of the used admixture have an important effect on the extent of chloride induced corrosion of the steel. The mechanism of corrosion of steel due to chloride attack was discussed. (Edited author abstract) 16 Refs.展开更多
The present work evaluated the deviations in the quality of steel reinforcing bars in terms of markings, diameter, yield strength and ductility in order to facilitate the drawing up of a yield strength value for the C...The present work evaluated the deviations in the quality of steel reinforcing bars in terms of markings, diameter, yield strength and ductility in order to facilitate the drawing up of a yield strength value for the Cameroon National Annex to Eurocode 2. The methodology of the work started with the collection of steel samples from various active building project sites in four different towns viz: Bamenda, Douala, Maroua and Yaoundé and testing their tensile strength and elongation using a Universal Testing Machine and also carrying out the bending test. Results show that bars without marked manufacturer’s name fell all the tests. Other results show that 52% of all the steel had yield stresses below 400 Mpa and the highest deviation in the yield strengths was 22.50%. The study recommends that properly marked grade 500 steel bars should be adopted in the Cameroon national annex to Eurocode 2.展开更多
SAE1010 structural carbon steel,which has a low cost price and wide range of use in the construction industry,has been studied as dual phase (DP) steel subjected to appropriate heat treatment,and its mechanical prop...SAE1010 structural carbon steel,which has a low cost price and wide range of use in the construction industry,has been studied as dual phase (DP) steel subjected to appropriate heat treatment,and its mechanical properties have been investigated under various tempering conditions. Intercritical annealing heat treatment has been applied to the reinforcing steel in order to obtain DP steels with different martensite volume fraction. In addition,these DP steels have been tempered at 200,300 and 400 ℃ for 45 min and then cooled to the room temperature. Mechanical properties such as tensile strength,yield strength,reduction in cross-sectional area,total elongation,resilience modulus and toughness have been examined. Furthermore,fractographic examination has been done with scanning electron microscope (SEM) as well as metallographic examination of the steels. As a result of this study,it is found that mechanical properties of DP steel have changed according to the hardness and ratio of martensite phase. In addition,tensile strength,yield strength and resilience modulus of the steels have been reduced. In contrast,the total elongation,reduction of the cross-sectional area and toughness have been increased.展开更多
The Standard Test Methods for Tension Testing of Metallic Materials (ASTM E8) mandates a specimen gauge reduction for obtaining the tensile properties of reinforcing steel bars. The standard outlines the specimen prep...The Standard Test Methods for Tension Testing of Metallic Materials (ASTM E8) mandates a specimen gauge reduction for obtaining the tensile properties of reinforcing steel bars. The standard outlines the specimen preparation requirements and methods to ensure that test results well represent the material properties. On the other hand, some codes differ regarding the approach to specimen preparation. They do not apply gauging, for both deformed and plain steel bars. Thus, the effect of specimen gauge reduction on the tensile properties of reinforcing steel bars was evaluated, and the interconnection of properties to the layer hardness was analysed. The experiment governed a range of deformed hot-rolled bar sizes, tested in tension using precision instruments. The Rockwell hardness test was implemented layerwise on the specimen’s cross section, and the hardness number (HRC) was measured as a function of the layer distance to the centre. A finite element model was constructed to study the stress concentrations induced by a constant indentation, simulating the HRCs, and to numerically construct the stress–strain relationship of ungauged steel bars based on the core properties and the section HRC relationship. Scanning electron microscopy readings were performed to visually and chemically justify the results. It was shown that the specimen gauge reduction significantly influenced the resulting stress–strain behaviour of the material, and the yield and ultimate strengths were reduced. It was also demonstrated that the hardness response is proportional to the distance to the specimen’s axes. The corresponding yield and ultimate strengths thus increased accordingly, from the inner to the outer layers of the bar. Testing a gauged specimen will therefore result in lower strength than that of an ungauged steel bar.展开更多
The general goal of this research is to investigate whether steel fiber has a significant “positive” or “negative” influence on concrete compressive strength, as well as the optimal steel fiber ratio that delivers...The general goal of this research is to investigate whether steel fiber has a significant “positive” or “negative” influence on concrete compressive strength, as well as the optimal steel fiber ratio that delivers best result. Manually, cement, fine aggregates, coarse aggregates, steel fibers, and water were mixed together properly. A slump test was carried on the mixed concrete. After determining the workability, the mixed concrete was poured into cubes dimension 150 mm × 150 mm × 150 mm and left for 24 hours. After 24 hours, the samples were removed from the mold and placed in a water tank to cure for 7 to 28 days. The cube was tested for compressive and flexural strength in a universal testing machine after the samples had cured for the required 7 - 28 days. This study focuses on how to obtain high strength concrete using with steel fiber in the Conventional mix ratio to enhance concrete strength. Concrete reinforcement using steel fibers alters the characteristics of the concrete, allowing it to withstand fracture and hence improve its mechanical qualities. This study reports on an experimental study that reveals the effect of steel fiber on concrete compressive strength and the optimal steel fiber ratio that produces the best results. Steel fiber reinforcing improved the compressive strength of concrete. The average compressive strength of normal M25 concrete with 0% steel fibers and curing ages of 7 and 28 days was determined to be 22.97 N/mm<sup>2</sup> and 25.78 N/mm<sup>2</sup>, respectively. The steel fibers are then added in various concentrations, such as 1%, 2%, and 3%, with aspect ratios of 70. The compressive strength of concrete with 1%, 2%, and 3% steel fiber with an aspect ratio of 70 was examined at 7 days and found to be 23.96, 24.80, and 26.14 N/mm<sup>2</sup> correspondingly.展开更多
The tensile strength of a corroded rebar in a 53-year-old concrete structure was studied. The microstructure of the metallic substrate, the fracture surface, and the corrosion product layers were investigated. Metallo...The tensile strength of a corroded rebar in a 53-year-old concrete structure was studied. The microstructure of the metallic substrate, the fracture surface, and the corrosion product layers were investigated. Metallographic observation results showed that the carbon steel was constituted of ferrite and some pearlite. The tensile test results indicated that the corroded rebar presented low strength and elongation. In addition, the fracture surface of the rebar in the tensile test displayed dimple fracture behavior. The Raman spectroscopy results indicated that corrosion products at the general corrosion zone were obviously different from those at the localized corrosion zone. The rust layer at the general corrosion zone was composed of goethite (α-FeOOH), magnetite (Fe304), and hematite (α-Fe203), while that of the pitting zone was made of feroxyhyte (δ-FeOOH), goethite (α-FeOOH), and hematite (α-Fe203). However, the general tendencies that the corrosion products were constituted of a mix of oxides and hydroxides, the oxides mainly existed in the internal part and the hydroxides more presented in the external layer were observed.展开更多
Electrochemical impedance spectroscopy, cyclic potentiodynamic polarization measurements, and scanning electron microscopy in conjunction with energy-dispersive X-ray spectroscopy were used to investigate the influenc...Electrochemical impedance spectroscopy, cyclic potentiodynamic polarization measurements, and scanning electron microscopy in conjunction with energy-dispersive X-ray spectroscopy were used to investigate the influence of mill scale and rust layer on the passivation capability and chloride-induced corrosion behaviors of conventional low-carbon(LC) steel and low-alloy(LA) steel in simulated concrete pore solution. The results show that mill scale exerts different influences on the corrosion resistance of both steels at various electrochemical stages. We propose that the high long-term corrosion resistance of LA steel is mainly achieved through the synergistic effect of a gradually formed compact, adherent and well-distributed Cr-enriched inner rust layer and the physical barrier protection effect of mill scale.展开更多
To investigate the seismic performance of a composite frame comprised of steel reinforced ultra high-strength concrete (SRUHSC) columns and steel reinforced concrete (SRC) beams, six interior frame joint specimens...To investigate the seismic performance of a composite frame comprised of steel reinforced ultra high-strength concrete (SRUHSC) columns and steel reinforced concrete (SRC) beams, six interior frame joint specimens were designed and tested under low cyclically lateral load. The effects of the axial load ratio and volumetric stirrup ratio were studied on the characteristics of the frame joint performance including crack pattern, failure mode, ductility, energy dissipation capacity, strength degradation and rigidity degradation. It was found that all joint specimens behaved in a ductile manner with flexural-shear failure in the joint core region while plastic hinges appeared at the beam ends. The ductility and energy absorption capacity of joints increased as the axial load ratio decreased and the volumetric stirIup ratio increased. The displacement ductility coefficient and equivalent damping coefficient of the joints fell between the corresponding coefficients of the steel reinforced concrete (SRC) frame joint and RC frame joint. The axial load ratio and volumetric stirrup ratio have less influence on the strength degradation and more influence on the stiffness degradation. The stiffness of the joint degrades more significantly for a low volumetric stirrup ratio and high axial load ratio. The characteristics obtained from the SRUHSC composite frame joint specimens with better seismic performance may be a useful reference in future engineering applications.展开更多
In this paper, a steel-concrete multi-energy dissipation composite shear wall, comprised of steel-reinforced concrete (SRC) columns, steel plate (SP) deep beams, a concrete wall and energy dissipation strips, is p...In this paper, a steel-concrete multi-energy dissipation composite shear wall, comprised of steel-reinforced concrete (SRC) columns, steel plate (SP) deep beams, a concrete wall and energy dissipation strips, is proposed. In order to study the multi-energy dissipation behavior and restorability after an earthquake, two stages of low cyclic loading tests were carded out on ten test specimens. In the first stage, test on five specimens with different number of SP deep beams was carried out, and the test lasted until the displacement drift reached 2%. In the second stage, thin SPs were welded to both sides of the five specimens tested in the first stage, and the same test was carried out on the repaired specimens (designated as new specimens). The load-bearing capacity, stiffness, ductility, hysteretic behavior and failure characteristics were analyzed for both stages and the results are discussed herein. Extrapolating from these results, strength calculation models and formulas are proposed herein and simulations using ABAQUS carried out, they show good agreement with the test results. The study demonstrates that SRC columns, SP deep beams, concrete wall and energy dissipation strips cooperate well and play an important role in energy dissipation. In addition, this study shows that the shear wall has good recoverability after an earthquake, and that the welding of thin SP's to repair a deformed wall is a practicable technique.展开更多
This paper describes a series of experimental investigations on seventeen specimens of steel reinforced concrete special shaped(SRCSS) columns under low cyclic reversed loading using parallel crosshead equipment. Nine...This paper describes a series of experimental investigations on seventeen specimens of steel reinforced concrete special shaped(SRCSS) columns under low cyclic reversed loading using parallel crosshead equipment. Nine T-shaped SRC columns, four L-shaped SRC columns and four +-shaped SRC columns were tested to examine the effects of shape steel confi guration, loading angle, axial compressive ratio and shear-span ratio on the behavior(strength, stiffness, energy dissipation, ductility, etc.) of SRCSS column specimens. The failure modes and hysteretic performance of all the specimens were obtained in the tests. Test results demonstrate that the shear-span ratio is the main parameter affecting the failure modes of SRCSS columns. The specimens with small shear-span ratio are prone to shear failure, and the primary failure planes in SRCSS columns are parallel to the loading direction. As a result, there is a symmetry between positive and negative loading directions in the hysteretic curves of the SRCSS columns. The majority of displacement ductility coeffi cients for all the specimens are over 3.0, so that the SRCSS columns demonstrate a better deformation capacity. In addition, the equivalent viscous damping coeffi cients of all the specimens are greater than 0.2, indicating that the seismic behavior of SRCSS columns is adequate. Finally, the superposition theory was used to calculate the limits of axial compressive ratio for the specimens, and it is found that the test axial compressive ratio is close to or smaller than the calculated axial compressive ratio limit.展开更多
To explore a new structure form of fiber reinforced concrete, namely, the layered steel fiber and layered hybrid fiber reinforced concrete (LSFRC and LHFRC), the mechanical properties of LSFRC and LHFRC, such as com...To explore a new structure form of fiber reinforced concrete, namely, the layered steel fiber and layered hybrid fiber reinforced concrete (LSFRC and LHFRC), the mechanical properties of LSFRC and LHFRC, such as compressive strength, tensile strength, flexural strength, fatigue and durability were focused on. The experimental results show that LSFRC and LHFRC can improve the flexural strength of concrete by 20%-50%. In the aspect of improving the flexural strength of concrete, adulterant rate has more obvious effect than length/diameter ratio. Double logarithmic fatigue equation considered liveability was founded. The impermeability of LHFRC is superior to LSFRC and plain concrete (C). However, the porosity of LHFRC is lower than LSFRC and C. The shrinkage of LHFRC at every age is obviously lower than C. The antifreeze durability of LHFRC is also better than C.展开更多
Steel fiber reinforced concrete(SFRC)has drawn extensive attention in recent years for its superior mechanical response to dynamic and impact loadings.Based on the existing test results,the highstrength steel fibers e...Steel fiber reinforced concrete(SFRC)has drawn extensive attention in recent years for its superior mechanical response to dynamic and impact loadings.Based on the existing test results,the highstrength steel fibers embedded in a concrete matrix usually play a strong bridging effect to enhance the bonding force between fiber and the matrix,and directly contribute to the improvement of the post-cracking behavior and residual strength of SFRC.To gain a better understanding of the action behavior of steel fibers in matrix and further capture the failure mechanism of SFRC under dynamic loads,the mesoscopic modeling approach that assumes SFRC to be composed of different mesoscale phases(i.e.,steel fibers,coarse aggregates,mortar matrix,and interfacial transition zone(ITZ))has been widely employed to simulate the dynamic responses of SFRC material and structural members.This paper presents a comprehensive review of the state-of-the-art mesoscopic models and simulations for SFRC under dynamic loading.Generation approaches for the SFRC mesoscale model in the simulation works,including steel fiber,coarse aggregate,and the ITZ between them,are reviewed and compared systematically.The material models for different phases and the interaction relationship between fiber and concrete matrix are summarized comprehensively.Additionally,some example applications for SFRC under dynamic loads(i.e.,compression,tension,and contact blast)simulated using the general mesoscale models are given.Finally,some critical analysis on the current shortcomings of the mesoscale modeling of SFRC is highlighted,which is of great significance for the future investigation and development of SFRC.展开更多
A whole of 110 specimens divided into 22 groups were tested with varying the volume fraction of steel fibers and the matrix strength of these specimens. The stress-strain behaviors of four types of steel fiber reinfo...A whole of 110 specimens divided into 22 groups were tested with varying the volume fraction of steel fibers and the matrix strength of these specimens. The stress-strain behaviors of four types of steel fiber reinforced concrete (SFRC) under uniaxial tension were studied experimentally. When the matrix strength and the fiber content increase, the tensile stress and tensile strain vary differently according to the fiber type. The mechanisms of reinforcing effect for different types of fiber were analyzed and the stress-strain curves of the specimens were plotted. Some experimental factors for stress or strain of SFRC were given. A tensile toughness modulus Re0.5 was introduced to evaluate the toughness characters of SFRC under uniaxial tension. Moreover, the formula of the tensile stress-strain curve of SFRC was regressed. The theoretical curve and the experimental ones fit well, which can be used for references in construction.展开更多
The constitutive relation of bond-slip on steel and concrete interface is proposed for short steel reinforced concrete (SRC) column. Based on the experimental research on bond-slip performance, a mechanical model of...The constitutive relation of bond-slip on steel and concrete interface is proposed for short steel reinforced concrete (SRC) column. Based on the experimental research on bond-slip performance, a mechanical model of short SRC column in pulling or pushing test is established. By means of the elasto-plasticity theory the explicit formulation of bond-slip constitutive relation τ-s in different anchor-hold place of push and pull member is investigated under the conditions of balance and boundary. The study shows that the constitutive relation is relevant to the embedment length and the thickness of concrete cover. The results are continuous descriptions of bond-slip constitutive relation and can be used to analyze the non-linear performance of SRC members. Results indicate that the principle of the method is correct and it performs well for short SRC column.展开更多
基金Federal Highway Administration Under Contract No.DTFH61-07-R-00121International Molybdenum Association,Nickel Institute,Talley Metals-A Carpenter Company,North American Stainless and Salit Specialty Steel Through MCEER,University at Buffalo
文摘Use of stainless reinforcing steel (SRS) in reinforced concrete (RC) structures is a promising solution to corrosion issues. However, for SRS to be used in seismic applications, several mechanical properties need to be investigated. These include specified and actual yield strengths, tensile strengths, uniform elongations and low-cycle fatigue behavior. Three types of SRSs (Talley S24100, Talley 316LN and Talley 2205) were tested and the results are reported in this paper. They were compared with the properties of A706 carbon reinforcing steel (RS), which is typical for seismic applications, and MMFX II, which is a high strength, corrosion resistant RS. Low-cycle fatigue tests of the RS coupons were conducted under strain control with constant amplitude to obtain strain life models of the steels. Test results show that the SRSs have slightly lower moduli of elasticity, higher uniform elongations before necking, and better low-cycle fatigue performance than A706 and MMFX II. All five types of RSs tested satisfy the requirements of the ACI 318 code on the lower limit of the tensile to yield strength ratio. Except Talley 2205, the other four types of RSs investigated meet the ACI 318 requirement that the actual yield strength does not exceed the specified yield strength by more than 18 ksi (124 MPa). Among the three types of SRSs tested, Talley S24100 possesses the highest uniform elongation before necking, and the best low-cycle fatigue performance.
文摘Electrochemical techniques of the corrosion measurements of reinforcing steeI in concrete have been evaluated. These techniques include half-cell potential measurements, impressed voltage method, impressed current method and potentiostatic polarization technique. The results of corrosion behaviour of the steel in both 5%NaCl and 5%MgSO4 show that each electrochemical technique provides some information about the condition of the steel bar or the corrosivity of the environment being evaluated, yet none provides a complete data regarding the corrosion resistance of reinforcing steel in aggressive media
文摘The mechanical and physical properties of concrete specimens obtained from replacing natural coarse aggregate with waste vehi- cle rubber tires at levels of 2vol%, 5vol%, 7vol%, and 10vol% were studied, and the corrosion behavior of reinforcing steels was investigated in these specimens. Corrosion rates were determined by measuring the galvanic current between steel-reinforced concrete specimens both with and without chloride addition. The change in electrode potential of reinforcing steels in these concrete specimens was measured daily for a period of 60 d in accordance with the testing method in ASTM C876. The results show that the use of waste vehicle tires in concrete instead of coarse aggregate decreases the mechanical strength of the specimens, and increases the corrosion rates of the reinforcing steels embedded in the concretes.
基金Supported by National Natural Science Foundation of China(Nos.51178154 and 51008098)
文摘Reinforcement corrosion is the major cause of damage and early failure of reinforced concrete structures worldwide with subsequent enormous costs for maintenance, restoration and replacement. Many methods used today for assessment of reinforcement corrosion are based on electrochemical techniques that determine the free corrosion potential or polarization resistance. Most of these methods always consider the B value in Stern-Geary equation as constant. However, B changes with different condition. In this paper, potentialdynamic method is used to characterize the corrosion of reinforcing steel. The corrosion rate of Q235 carbon steel is measured with concrete environment. B is calculated real-time. By this way, the error of reinforcement corrosion rate is minimized.
文摘The use of a natural white juice, taken from magrabe banana stem, as concrete admixture to improve mechanical and physicrvchemical properties of concrete has been studied. The compressive strength, bulk density the free lime liberated during hydration and the combined water content were determined. The results indicate that the admixture acts as a retarder in most cases and as accelerator in some ones. Also, the admixture effect on the corrosion resistance of the reinforcing steel against surrounding aggressive media has been investigated using galvanostatic polarization technique. The addition of 0.2% admixture leads to the more inhibition of the steel
文摘Corrosion and electrochemical behaviour of reinforcing steel embedded in cement pastes with and without concrete admixtures used in Egypt to modify concrete properties have been studied. The influence of the admixtures on the corrosion resistance of the steel against chloride attack has been studied by using impressed current and impressed voltage techniques. The results indicate that the type and concentration of the used admixture have an important effect on the extent of chloride induced corrosion of the steel. The mechanism of corrosion of steel due to chloride attack was discussed. (Edited author abstract) 16 Refs.
文摘The present work evaluated the deviations in the quality of steel reinforcing bars in terms of markings, diameter, yield strength and ductility in order to facilitate the drawing up of a yield strength value for the Cameroon National Annex to Eurocode 2. The methodology of the work started with the collection of steel samples from various active building project sites in four different towns viz: Bamenda, Douala, Maroua and Yaoundé and testing their tensile strength and elongation using a Universal Testing Machine and also carrying out the bending test. Results show that bars without marked manufacturer’s name fell all the tests. Other results show that 52% of all the steel had yield stresses below 400 Mpa and the highest deviation in the yield strengths was 22.50%. The study recommends that properly marked grade 500 steel bars should be adopted in the Cameroon national annex to Eurocode 2.
文摘SAE1010 structural carbon steel,which has a low cost price and wide range of use in the construction industry,has been studied as dual phase (DP) steel subjected to appropriate heat treatment,and its mechanical properties have been investigated under various tempering conditions. Intercritical annealing heat treatment has been applied to the reinforcing steel in order to obtain DP steels with different martensite volume fraction. In addition,these DP steels have been tempered at 200,300 and 400 ℃ for 45 min and then cooled to the room temperature. Mechanical properties such as tensile strength,yield strength,reduction in cross-sectional area,total elongation,resilience modulus and toughness have been examined. Furthermore,fractographic examination has been done with scanning electron microscope (SEM) as well as metallographic examination of the steels. As a result of this study,it is found that mechanical properties of DP steel have changed according to the hardness and ratio of martensite phase. In addition,tensile strength,yield strength and resilience modulus of the steels have been reduced. In contrast,the total elongation,reduction of the cross-sectional area and toughness have been increased.
文摘The Standard Test Methods for Tension Testing of Metallic Materials (ASTM E8) mandates a specimen gauge reduction for obtaining the tensile properties of reinforcing steel bars. The standard outlines the specimen preparation requirements and methods to ensure that test results well represent the material properties. On the other hand, some codes differ regarding the approach to specimen preparation. They do not apply gauging, for both deformed and plain steel bars. Thus, the effect of specimen gauge reduction on the tensile properties of reinforcing steel bars was evaluated, and the interconnection of properties to the layer hardness was analysed. The experiment governed a range of deformed hot-rolled bar sizes, tested in tension using precision instruments. The Rockwell hardness test was implemented layerwise on the specimen’s cross section, and the hardness number (HRC) was measured as a function of the layer distance to the centre. A finite element model was constructed to study the stress concentrations induced by a constant indentation, simulating the HRCs, and to numerically construct the stress–strain relationship of ungauged steel bars based on the core properties and the section HRC relationship. Scanning electron microscopy readings were performed to visually and chemically justify the results. It was shown that the specimen gauge reduction significantly influenced the resulting stress–strain behaviour of the material, and the yield and ultimate strengths were reduced. It was also demonstrated that the hardness response is proportional to the distance to the specimen’s axes. The corresponding yield and ultimate strengths thus increased accordingly, from the inner to the outer layers of the bar. Testing a gauged specimen will therefore result in lower strength than that of an ungauged steel bar.
文摘The general goal of this research is to investigate whether steel fiber has a significant “positive” or “negative” influence on concrete compressive strength, as well as the optimal steel fiber ratio that delivers best result. Manually, cement, fine aggregates, coarse aggregates, steel fibers, and water were mixed together properly. A slump test was carried on the mixed concrete. After determining the workability, the mixed concrete was poured into cubes dimension 150 mm × 150 mm × 150 mm and left for 24 hours. After 24 hours, the samples were removed from the mold and placed in a water tank to cure for 7 to 28 days. The cube was tested for compressive and flexural strength in a universal testing machine after the samples had cured for the required 7 - 28 days. This study focuses on how to obtain high strength concrete using with steel fiber in the Conventional mix ratio to enhance concrete strength. Concrete reinforcement using steel fibers alters the characteristics of the concrete, allowing it to withstand fracture and hence improve its mechanical qualities. This study reports on an experimental study that reveals the effect of steel fiber on concrete compressive strength and the optimal steel fiber ratio that produces the best results. Steel fiber reinforcing improved the compressive strength of concrete. The average compressive strength of normal M25 concrete with 0% steel fibers and curing ages of 7 and 28 days was determined to be 22.97 N/mm<sup>2</sup> and 25.78 N/mm<sup>2</sup>, respectively. The steel fibers are then added in various concentrations, such as 1%, 2%, and 3%, with aspect ratios of 70. The compressive strength of concrete with 1%, 2%, and 3% steel fiber with an aspect ratio of 70 was examined at 7 days and found to be 23.96, 24.80, and 26.14 N/mm<sup>2</sup> correspondingly.
基金Funded by the National Natural Science Foundation of China(51301060,51210001)the 111 Project(B12032)+1 种基金the Key Laboratory of Advanced Civil Engineering Materials(Tongji University),Ministry of Educationthe Fundamental Research Funds for the Central Universities(No.2013B03514)
文摘The tensile strength of a corroded rebar in a 53-year-old concrete structure was studied. The microstructure of the metallic substrate, the fracture surface, and the corrosion product layers were investigated. Metallographic observation results showed that the carbon steel was constituted of ferrite and some pearlite. The tensile test results indicated that the corroded rebar presented low strength and elongation. In addition, the fracture surface of the rebar in the tensile test displayed dimple fracture behavior. The Raman spectroscopy results indicated that corrosion products at the general corrosion zone were obviously different from those at the localized corrosion zone. The rust layer at the general corrosion zone was composed of goethite (α-FeOOH), magnetite (Fe304), and hematite (α-Fe203), while that of the pitting zone was made of feroxyhyte (δ-FeOOH), goethite (α-FeOOH), and hematite (α-Fe203). However, the general tendencies that the corrosion products were constituted of a mix of oxides and hydroxides, the oxides mainly existed in the internal part and the hydroxides more presented in the external layer were observed.
基金the support by the National Natural Science Foundation of China(Nos.51208098 and 51678144)the National Basic Research Program of China(No.2015CB655100)+1 种基金the Natural Science Foundation of Jiangsu Province(No.BK20161420)Industry-University Research Cooperative Innovation Fund of Jiangsu Province(No.BY2013091)
文摘Electrochemical impedance spectroscopy, cyclic potentiodynamic polarization measurements, and scanning electron microscopy in conjunction with energy-dispersive X-ray spectroscopy were used to investigate the influence of mill scale and rust layer on the passivation capability and chloride-induced corrosion behaviors of conventional low-carbon(LC) steel and low-alloy(LA) steel in simulated concrete pore solution. The results show that mill scale exerts different influences on the corrosion resistance of both steels at various electrochemical stages. We propose that the high long-term corrosion resistance of LA steel is mainly achieved through the synergistic effect of a gradually formed compact, adherent and well-distributed Cr-enriched inner rust layer and the physical barrier protection effect of mill scale.
基金National Natural Science Foundation of China Under Grant No.50878037
文摘To investigate the seismic performance of a composite frame comprised of steel reinforced ultra high-strength concrete (SRUHSC) columns and steel reinforced concrete (SRC) beams, six interior frame joint specimens were designed and tested under low cyclically lateral load. The effects of the axial load ratio and volumetric stirrup ratio were studied on the characteristics of the frame joint performance including crack pattern, failure mode, ductility, energy dissipation capacity, strength degradation and rigidity degradation. It was found that all joint specimens behaved in a ductile manner with flexural-shear failure in the joint core region while plastic hinges appeared at the beam ends. The ductility and energy absorption capacity of joints increased as the axial load ratio decreased and the volumetric stirIup ratio increased. The displacement ductility coefficient and equivalent damping coefficient of the joints fell between the corresponding coefficients of the steel reinforced concrete (SRC) frame joint and RC frame joint. The axial load ratio and volumetric stirrup ratio have less influence on the strength degradation and more influence on the stiffness degradation. The stiffness of the joint degrades more significantly for a low volumetric stirrup ratio and high axial load ratio. The characteristics obtained from the SRUHSC composite frame joint specimens with better seismic performance may be a useful reference in future engineering applications.
基金Beijing Natural Science Foundation of China under Grant No.8122004the National Natural Science Foundation of China under Grant No.51178010the National Science and Technology Support Program of China under Grant No.2012BAJ13B02
文摘In this paper, a steel-concrete multi-energy dissipation composite shear wall, comprised of steel-reinforced concrete (SRC) columns, steel plate (SP) deep beams, a concrete wall and energy dissipation strips, is proposed. In order to study the multi-energy dissipation behavior and restorability after an earthquake, two stages of low cyclic loading tests were carded out on ten test specimens. In the first stage, test on five specimens with different number of SP deep beams was carried out, and the test lasted until the displacement drift reached 2%. In the second stage, thin SPs were welded to both sides of the five specimens tested in the first stage, and the same test was carried out on the repaired specimens (designated as new specimens). The load-bearing capacity, stiffness, ductility, hysteretic behavior and failure characteristics were analyzed for both stages and the results are discussed herein. Extrapolating from these results, strength calculation models and formulas are proposed herein and simulations using ABAQUS carried out, they show good agreement with the test results. The study demonstrates that SRC columns, SP deep beams, concrete wall and energy dissipation strips cooperate well and play an important role in energy dissipation. In addition, this study shows that the shear wall has good recoverability after an earthquake, and that the welding of thin SP's to repair a deformed wall is a practicable technique.
基金National Science Foundation of China under Grant Nos.50908057 and 51268004Open Project of Guangxi Key Laboratory of Disaster Prevention and Structural Safety under Grant No.2012ZDX10Innovation Project of Guangxi Graduate Education under Grant No.YCBZ2012005
文摘This paper describes a series of experimental investigations on seventeen specimens of steel reinforced concrete special shaped(SRCSS) columns under low cyclic reversed loading using parallel crosshead equipment. Nine T-shaped SRC columns, four L-shaped SRC columns and four +-shaped SRC columns were tested to examine the effects of shape steel confi guration, loading angle, axial compressive ratio and shear-span ratio on the behavior(strength, stiffness, energy dissipation, ductility, etc.) of SRCSS column specimens. The failure modes and hysteretic performance of all the specimens were obtained in the tests. Test results demonstrate that the shear-span ratio is the main parameter affecting the failure modes of SRCSS columns. The specimens with small shear-span ratio are prone to shear failure, and the primary failure planes in SRCSS columns are parallel to the loading direction. As a result, there is a symmetry between positive and negative loading directions in the hysteretic curves of the SRCSS columns. The majority of displacement ductility coeffi cients for all the specimens are over 3.0, so that the SRCSS columns demonstrate a better deformation capacity. In addition, the equivalent viscous damping coeffi cients of all the specimens are greater than 0.2, indicating that the seismic behavior of SRCSS columns is adequate. Finally, the superposition theory was used to calculate the limits of axial compressive ratio for the specimens, and it is found that the test axial compressive ratio is close to or smaller than the calculated axial compressive ratio limit.
基金the Technical Specification for Fiber Reinforced ConcreteStructure (No. CECS:2004 2000jb15)
文摘To explore a new structure form of fiber reinforced concrete, namely, the layered steel fiber and layered hybrid fiber reinforced concrete (LSFRC and LHFRC), the mechanical properties of LSFRC and LHFRC, such as compressive strength, tensile strength, flexural strength, fatigue and durability were focused on. The experimental results show that LSFRC and LHFRC can improve the flexural strength of concrete by 20%-50%. In the aspect of improving the flexural strength of concrete, adulterant rate has more obvious effect than length/diameter ratio. Double logarithmic fatigue equation considered liveability was founded. The impermeability of LHFRC is superior to LSFRC and plain concrete (C). However, the porosity of LHFRC is lower than LSFRC and C. The shrinkage of LHFRC at every age is obviously lower than C. The antifreeze durability of LHFRC is also better than C.
基金the financial support from the National Natural Science Foundation of China(52178190 and 52078250)the Science and Technology on Near-Surface Detection Laboratory(6142414200505)+1 种基金the Interdisciplinary Innovation Fundation for Graduates,Nanjing University of Aeronautics and Astronautics(KXKCXJJ202005)The support provided by the China Scholarship Council(202006830096)during a visit of Zhangyu Wu to University College London。
文摘Steel fiber reinforced concrete(SFRC)has drawn extensive attention in recent years for its superior mechanical response to dynamic and impact loadings.Based on the existing test results,the highstrength steel fibers embedded in a concrete matrix usually play a strong bridging effect to enhance the bonding force between fiber and the matrix,and directly contribute to the improvement of the post-cracking behavior and residual strength of SFRC.To gain a better understanding of the action behavior of steel fibers in matrix and further capture the failure mechanism of SFRC under dynamic loads,the mesoscopic modeling approach that assumes SFRC to be composed of different mesoscale phases(i.e.,steel fibers,coarse aggregates,mortar matrix,and interfacial transition zone(ITZ))has been widely employed to simulate the dynamic responses of SFRC material and structural members.This paper presents a comprehensive review of the state-of-the-art mesoscopic models and simulations for SFRC under dynamic loading.Generation approaches for the SFRC mesoscale model in the simulation works,including steel fiber,coarse aggregate,and the ITZ between them,are reviewed and compared systematically.The material models for different phases and the interaction relationship between fiber and concrete matrix are summarized comprehensively.Additionally,some example applications for SFRC under dynamic loads(i.e.,compression,tension,and contact blast)simulated using the general mesoscale models are given.Finally,some critical analysis on the current shortcomings of the mesoscale modeling of SFRC is highlighted,which is of great significance for the future investigation and development of SFRC.
基金Funded by Regulation RevisingItemof China Associationfor En-gineering Construction Standardization (CECS 15 :2000)
文摘A whole of 110 specimens divided into 22 groups were tested with varying the volume fraction of steel fibers and the matrix strength of these specimens. The stress-strain behaviors of four types of steel fiber reinforced concrete (SFRC) under uniaxial tension were studied experimentally. When the matrix strength and the fiber content increase, the tensile stress and tensile strain vary differently according to the fiber type. The mechanisms of reinforcing effect for different types of fiber were analyzed and the stress-strain curves of the specimens were plotted. Some experimental factors for stress or strain of SFRC were given. A tensile toughness modulus Re0.5 was introduced to evaluate the toughness characters of SFRC under uniaxial tension. Moreover, the formula of the tensile stress-strain curve of SFRC was regressed. The theoretical curve and the experimental ones fit well, which can be used for references in construction.
基金Sponsored by the Science and Technology Program Project of Henan Province(002462004)
文摘The constitutive relation of bond-slip on steel and concrete interface is proposed for short steel reinforced concrete (SRC) column. Based on the experimental research on bond-slip performance, a mechanical model of short SRC column in pulling or pushing test is established. By means of the elasto-plasticity theory the explicit formulation of bond-slip constitutive relation τ-s in different anchor-hold place of push and pull member is investigated under the conditions of balance and boundary. The study shows that the constitutive relation is relevant to the embedment length and the thickness of concrete cover. The results are continuous descriptions of bond-slip constitutive relation and can be used to analyze the non-linear performance of SRC members. Results indicate that the principle of the method is correct and it performs well for short SRC column.