Geological characteristics and high production control factors of shale gas reservoirs in Silurian Longmaxi Formation, southern Sichuan Basin, SW China

Marine shale gas resources have great potential in the south of the Sichuan Basin in China.At present,the high-quality shale gas resources at depth of 2000–3500 m are under effective development,and strategic breakthroughs have been made in deeper shale gas resources at depth of 3500–4500 m.To promote the effective production of shale gas in this area,this study examines key factors controlling high shale gas production and presents the next exploration direction in the southern Sichuan Basin based on summarizing the geological understandings from the Lower Silurian Longmaxi Formation shale gas exploration combined with the latest results of geological evaluation.The results show that:(1)The relative sea depth in marine shelf sedimentary environment controls the development and distribution of reservoirs.In the relatively deep water area in deep-water shelf,grade-I reservoirs with a larger continuous thickness develop.The relative depth of sea in marine shelf sedimentary environment can be determined by redox conditions.The research shows that the uranium to thorium mass ratio greater than 1.25 indicates relatively deep water in anoxic reduction environment,and the uranium to thorium mass ratio of 0.75–1.25 indicates semi-deep water in weak reduction and weak oxidation environment,and the uranium to thorium mass ratio less than 0.75 indicates relatively shallow water in strong oxidation environment.(2)The propped fractures in shale reservoirs subject to fracturing treatment are generally 10–12 m high,if grade-I reservoirs are more than 10 m in continuous thickness,then all the propped section would be high-quality reserves;in this case,the longer the continuous thickness of penetrated grade-I reservoirs,the higher the production will be.(3)The shale gas reservoirs at 3500–4500 m depth in southern Sichuan are characterized by high formation pressure,high pressure coefficient,well preserved pores,good pore structure and high proportion of free gas,making them the most favorable new field for shale gas exploration;and the pressure coefficient greater than 1.2 is a necessary condition for shale gas wells to obtain high production.(4)High production wells in the deep shale gas reservoirs are those in areas where Long11-Long13 sub-beds are more than 10 m thick,with 1500 m long horizontal section,grade-I reservoirs penetration rate of over 90%,and fractured by dense cutting+high intensity sand injection+large displacement+large liquid volume.(5)The relatively deep-water area in the deep-water shelf and the area at depth of 3500–4500 m well overlap in the southern Sichuan,and the overlapping area is the most favorable shale gas exploration and development zones in the southern Sichuan in the future.With advancement in theory and technology,annual shale gas production in the southern Sichuan is expected to reach 450×108 m3.

Is the feminization of labor harmful to agricultural production? The decision-making and production control perspective

Even today,academics continue to debate the effect of feminization of agricultural labor force on agricultural output.By considering the dimensions of participation in decision-making and production,this study divides the various agricultural production models into three types:(i)the traditional model of decisions made either jointly by men and women or by men alone while both genders participate in production,(ii)complete feminization of agricultural decision-making and the production labor force,and(iii)feminization of the agricultural production labor force only.This study investigates the effects of combining or separating decision-making and production in regard to agricultural development in the context of feminization of the agricultural labor force.Using follow-up data collected from 2004–2008 by the Ministry of Agriculture of China,we built a comprehensive panel data model to test our hypotheses.Our research shows that in comparison to traditional agricultural households and fully feminized agricultural labor forces,partially feminized production resulted in lower grain yield and technological advancement.The feminization of agricultural labor does not necessarily have a negative impact on agricultural output,especially since heavy manual labor is being increasingly replaced by agricultural machinery and outsourcing of tasks.The degree of feminization of the decision-making and production processes should be an important consideration when evaluating the purported negative effects of the feminization of agricultural labor.

Production Planning of a Failure-Prone Manufacturing/Remanufacturing System with Production-Dependent Failure Rates

This paper deals with the production-dependent failure rates for a hybrid manufacturing/remanufacturing system subject to random failures and repairs. The failure rate of the manufacturing machine depends on its production rate, while the failure rate of the remanufacturing machine is constant. In the proposed model, the manufacturing machine is characterized by a higher production rate. The machines produce one type of final product and unmet demand is backlogged. At the expected end of their usage, products are collected from the market and kept in recoverable inventory for future remanufacturing, or disposed of. The objective of the system is to find the production rates of the manufacturing and the remanufacturing machines that would minimize a discounted overall cost consisting of serviceable inventory cost, backlog cost and holding cost for returns. A computational algorithm, based on numerical methods, is used for solving the optimality conditions obtained from the application of the stochastic dynamic programming approach. Finally, a numerical example and sensitivity analyses are presented to illustrate the usefulness of the proposed approach. Our results clearly show that the optimal control policy of the system is obtained when the failure rates of the machine depend on its production rate.

MIIT issued 2017 the first batch of rare earth production control quotas

MIIT issued the notice about 2017 the first batch of rare earth production control quotas recently. According to the notice, overall rare earth mineral production quantity is controlled at 52,500 tons and smelting & separation products at 50,075 tons, while it was 52,500 tons and 45,000 tons, respectively, for 2016. According to the notice, rare earth control quotas shall be allocated to enterprises that meet the national rare earth industry policies and industrial development planning requirements.

Self-Triggered Set Stabilization of Boolean Control Networks and Its Applications

Set stabilization is one of the essential problems in engineering systems, and self-triggered control(STC) can save the storage space for interactive information, and can be successfully applied in networked control systems with limited communication resources. In this study, the set stabilization problem and STC design of Boolean control networks are investigated via the semi-tensor product technique. On the one hand, the largest control invariant subset is calculated in terms of the strongly connected components of the state transition graph, by which a graph-theoretical condition for set stabilization is derived. On the other hand, a characteristic function is exploited to determine the triggering mechanism and feasible controls. Based on this, the minimum-time and minimum-triggering open-loop, state-feedback and output-feedback STCs for set stabilization are designed,respectively. As classic applications of self-triggered set stabilization, self-triggered synchronization, self-triggered output tracking and self-triggered output regulation are discussed as well. Additionally, several practical examples are given to illustrate the effectiveness of theoretical results.

Research on Alliance Decision of Dual-Channel Remanufacturing Supply Chain Considering Bidirectional Free-Riding and Cost-Sharing

This study delves into the formation dynamics of alliances within a closed-loop supply chain(CLSC)that encom-passes a manufacturer,a retailer,and an e-commerce platform.It leverages Stackelberg game for this exploration,contrasting the equilibrium outcomes of a non-alliance model with those of three differentiated alliance models.The non-alliance model acts as a crucial benchmark,enabling the evaluation of the motivations for various supply chain entities to engage in alliance formations.Our analysis is centered on identifying the most effective alliance strategies and establishing a coordination within these partnerships.We thoroughly investigate the consequences of diverse alliance behaviors,bidirectional free-riding and cost-sharing,and the resultant effects on the optimal decision-making among supply chain actors.The findings underscore several pivotal insights:(1)The behavior of alliances within the supply chain exerts variable impacts on the optimal pricing and demand of its members.In comparison to the non-alliance(D)model,the manufacturer-retailer(MR)and manufacturer-e-commerce platform(ME)alliances significantly lower both offline and online resale prices for new and remanufactured goods.This adjustment leads to an enhanced demand for products via the MR alliance’s offline outlets and the ME alliance’s online platforms,thereby augmenting the profits for those within the alliance.Conversely,retailer-e-commerce platform(ER)alliance tends to increase the optimal retail price and demand across both online and offline channels.Under specific conditions,alliance behavior can also increase the profits of non-alliance members,and the profits derived through alliance channels also exceed those from non-alliance channels.(2)The prevalence of bidirectional free-riding behavior largely remains constant across different alliance configurations.Across these models,bidirectional free-riding typically elevates the equilibrium prices in offline channel while negatively affecting the equilibrium prices in other channel.(3)The effect of cost-sharing shows relative uniformity across the various alliance models.Across all configurations,cost-sharing tends to reduce the manufacturer’s profits.Nonetheless,alliances initiated by the manufacturer can counteract these negative impacts,providing a strategic pathway to bolster CLSC profitability.

A grouping strategy for reinforcement learning-based collective yawcontrol of wind farms

Reinforcement learning(RL)algorithms are expected to become the next generation of wind farm control methods.However,as wind farms continue to grow in size,the computational complexity of collective wind farm control will exponentially increase with the growth of action and state spaces,limiting its potential in practical applications.In this Letter,we employ a RL-based wind farm control approach with multi-agent deep deterministic policy gradient to optimize the yaw manoeuvre of grouped wind turbines in wind farms.To reduce the computational complexity,the turbines in the wind farm are grouped according to the strength of the wake interaction.Meanwhile,to improve the control efficiency,each subgroup is treated as a whole and controlled by a single agent.Optimized results show that the proposed method can not only increase the power production of the wind farm but also significantly improve the control efficiency.

Production Characteristics and the Control Factors of Surface Wells for Relieved Methane Drainage in the Huainan Mining Area

Based on the production data of a large number of surface drainage wells in the Huainan mining area,the present study shows that four types of typical production characteristics for relieved methane wells are recognized,of which the stable type for production and gas concentration is the most dominate,as determined by a comprehensive study on the volume and concentration of drained gases, as well as the stress changes of rocks influenced by mining.Some influence factors for the productive differences of the drainage wells were also been discussed.The results indicate that protective coal-seam mining has a significant effect on overlying strata,which promotes the development of pores and fractures of coal reservoirs for methane desorption and migration;however,the production and the stability of drainage wells are affected by deformation and damage of the overlying strata.The second distribution of strata stress is caused by mining engineering,and if the stress load is larger than the carrying capacity of the extraction well,the gas production would be influenced by the drainage well that has been damaged by rock movement.Furthermore,the case damage occurs first in the weak, lithologic interface by its special mechanical properties.The stability of drainage wells and the production status are also influenced by the different drilling techniques,uneven distribution of gas concentration,and combination of gob gas and methane from the protected layer.

Characteristics and control mechanisms of coalbed permeability change in various gas production stages

According to dimensionless analysis of the coalbed methane （CBM） production data of Fanzhuang block in southern Qinshui basin, the dimensionless gas production rate is calculated to quantitatively divide the CBM well production process into four stages, i.e., drai- nage stage, unstable gas production stage, stable gas pro- duction stage, and gas production decline stage. By the material balance method, the coal reservoir permeability change in different stages is quantitatively characterized. The characteristics and control mechanisms of change in coalbed permeability （CICP） during different production stages are concluded on five aspects, i.e., permeability trend variation, controlling mechanism, system energy, phase state compositions, and production performance. The study reveals that CICP is characterized by first decline, then recovery, and finally by increase and is controlled directly by effective stress and matrix shrinkage effects. Further, the duration and intensity of the matrix shrinkage effect are inherently controlled by adsorption and desorp- tion features.

A sand-production control system for gas production from clayey silt hydrate reservoirs

Sand production is a crucial problem during the process of extracting natural gas from hydrate reservoirs. To deal with sand-production problems systematically, a sand-production control system (SCS) is first proposed in this paper, specialized for pore-distributed clayey silt hydrate reservoirs. Secondly, a nodal system analysis method (NSAM) is applied to analyze the sand migration process during hydrate exploitation. The SCS is divided into three sub-systems, according to different sand migration mechanisms, and three key scientific problems and advances in SCS research in China Geological Survey are reviewed and analyzed. The maximum formation sanding rate, proper sand-control gravel size, and borehole blockage risk position were provided for clayey hydrate exploitation wells based on the SCS analysis. The SCS sub-systems are closely connected via bilateral coupling, and coordination of the subsystems is the basis of maintaining formation stability and prolonging the gas production cycle. Therefore, contradictory mitigation measures between sand production and operational systems should be considered preferentially. Some novel and efficient hydrate exploitation methods are needed to completely solve the contradictions caused by sand production.

Design and Control of Thermally Coupled Reactive Distillation Sequence for Biodiesel Production

Decreasing petroleum reserves and growing alternative fuels requirements have promoted the study of biodiesel production. In this work, two thermally coupled reactive distillation designs for biodiesel production were investigated, and the sensitivity analysis was conducted to obtain the appropriate design values. The thermodynamic analysis and economics evaluation were performed to estimate the superiority of the thermally coupled designs over the base case. The proposed biodiesel production processes were simulated using the simulator Aspen Plus, and calculation results show that the exergy loss and economic cost in the two thermally coupled designs can be greatly reduced. It is found that the thermally coupled side-stripper reactive distillation design provides more economic benefits than the side-rectifier one. The dynamic performance of the thermally coupled side-stripper design was investigated and the results showed that the proposed control structure could effectively handle large feed disturbances.

Change and control of nitrogen in molten steel production process

The change and control of nitrogen content in molten steel was investigated through the production process of "LDBAr-LF-RH-CC". Results show that nitrogen content reduces gradually in converter-steelmaking stage, rises rapidly from the end of converter process to the end of argon station process, continues to increase in ladle furnace process, and decreases slightly in RH refining stage. Since nitrogen is removed mainly by BOF steelmaking and vacuum refining operations, nitrogen in molten steel should be removed as much as possible in these two operations. However, nitrogen uptake should be minimized in other operations of molten steel production process.

Thermal Transformations in the System NaF-CaF₂-AlF₃and X-Ray Diffraction Control of Ca-Containing Electrolytes for Aluminum Production

The details of ternary fluoride crystallization in the system NaF-CaF2-AlF3 have been specified. The phases NaCaAlF6, Na2Ca3Al2F14 and NaAlF4 have been obtained by high-temperature synthesis. Their thermal transformations have been studied using high-temperature X-ray diffraction. The occurring transformations can be considered in a quasibinary system CaF2-NaAlF4, where at T = 745°C - 750°C invariant equilibrium is established with the phases CaF2-NaCaAlF6-Na2Ca3Al2F14-(NaAlF4). The compounds NaCaAlF6 and Na2Ca3Al2F14 are stable in different temperature ranges. The phase NaCaAlF6 was fixed by rapid quenching from the melt. It decomposes at heating before 640°C yielding Na2Ca3Al2F14 and NaAlF4. Direct and inverse transformations between NaCaAlF6 and Na2Ca3Al2F14 occur in the bulk samples of the electrolyte. A thermal treatment procedure was proposed for the solid electrolyte sample to get a sample corresponding to the composition of the melt and providing high phase crystallinity for the purposes of quantitative X-ray phase diffraction analysis.

An Improved Production Activity Control Architecture for Shop Floor Control

This paper presents a further improved Production Activity Control Architecture to deal with the complexity of information by creating Sub-Producers and Sub-Movers which will not only give a better control at workstation level but also reduce load on the Dispatcher. It also makes an analysis of the basic and improved PAC (Production Activity Control) Architecture in the Control System for Integrated Manufacturing. The PAC Architecture and the improvement will further enhance the flexibility and adaptability of the architecture in the ever changing environment of the Shop Floor Control (SFC) Systems.

Research on Production Process Control Method Combined Stochastic Process Algebra and Stochastic Petri Nets

A hierarchical closed-loop production control scheme integrating scheduling,control and performance evaluation is discussed.Firstly,the production process is divided into two main hierarchies:the lower level is the physical operation level and the upper one is the management level.Secondly,the schedule template for the management level and the activity template for the physical operation level are constructed separately,the tasks in the schedule have the ability to make partial decisions,and the per- formance parameters are introduced into activity template.Thirdly,the two levels use different model representations:stochastic process algebra for the management level whose output is the control commands and stochastic Petri net for the physical operation lev- el which is the execution of the control commands.Then,the integration of the two levels is the control commands mapping into the lower physical operations and the responses feeding back to the upper decision-making that are defined by some transition functions. Under the proposed scheme,the production process control of a flexible assembly is exemplified.It is concluded that the process con- trol model has partial ability to make decision on-line for uncertain and dynamic environments and facilitates reasoning about the be- haviors of the process control,and performance evaluation can be done online for real-time scheduling to ensure the global optimiza- tion.

The Development of the Production Management and Control System for 10th Assembly Workshop under XAC-CIMS

This paper gives brief introduction to the production management and control system (PMCS) for 10th assembly workshop under Xi’ an Aircraft Company (XAC)--CIMS. Its user requirements 9 structure, ftinctions, and implementation are described. It is showed that the development problems of PMCS can be further reduced to a development methodology for Chinese enterprises, which will make them competitive.

Adaptive Control of a Production-Inventory Model with Uncertain Deterioration Rate

This paper studied a continuous-time model of a production maintenance system in which a manufacturing firm produces a single product selling some and stocking the remaining. The problem of adaptive control of a production-maintenance system with unknown deterioration has been presented. Using Liapunov technique, the production rate and updating rule of deterioration rate are derived as non-linear functions of inventory level perturbation. Numerical analysis for the system has been presented for a set of parameter values and demand rate.

The Major Recessive Calamities Affecting the Wheat Production in Chuxiong Prefecture and Control Countermeasures

The impact of recessive calamities was analyzed,including seasonal drought,cold injury,dry hot wind and aphid in the wheat production of Chuxiong Prefecture,and the countermeasures that prevented and controlled the recessive calamities in a target-oriented way were proposed,including the improvement of basic farmland,the application of organic manure,the promotion of the breed with high stress resistance,the seedling at suitable date,the improvement of control on fertilizing and watering,the enhancement of management on cultivating and controlling disease in time,and the breeding new variety adaptive to local ecosystem,in order to advance the wheat production in a sustainable way.

Distributed Stretching Control of Web Production System

The stretching process,as a key phase of web production system,pursues the target velocities of rollers and the web tensions of spans between the successive rollers to guarantee proper stretching ratios. This requires the stable velocities and velocity ratios of large number rollers separated throughout the workshop. To this goal,a distributed cooperative controller is designed to coordinate the velocities of the rollers to the desired values as well as the target ratios between the upper and lower rollers. During the whole evolution,only the neighbor rollers can exchange the working information,and neither global information nor central controller is required. It is proven that all the rollers asymptotically achieve the desired velocity ratios via the proposed control law,which is also demonstrated by numerical simulation.