Laboratory study of fluid viscosity induced ultrasonic velocity dispersion in reservoir sandstones

Ultrasonic velocities of a set of saturated sandstone samples were measured at simulated in-situ pressures in the laboratory.The samples were obtained from the W formation of the WXS Depression and covered low to nearly high porosity and permeability ranges.The brine and four different density oils were used as pore fluids,which provided a good chance to investigate fluid viscosity-induced velocity dispersion.The analysis of experimental observations of velocity dispersion indicates that（1）the Biot model can explain most of the small discrepancy（about 2–3%）between ultrasonic measurements and zero frequency Gassmann predictions for high porosity and permeability samples saturated by all the fluids used in this experiment and is also valid for medium porosity and permeability samples saturated with low viscosity fluids（less than approximately 3 mP·S）and（2）the squirt flow mechanism dominates the low to medium porosity and permeability samples when fluid viscosity increases and produces large velocity dispersions as high as about 8%. The microfracture aspect ratios were also estimated for the reservoir sandstones and applied to calculate the characteristic frequency of the squirt flow model,above which the Gassmann’ s assumptions are violated and the measured high frequency velocities cannot be directly used for Gassmann’s fluid replacement at the exploration seismic frequency band for W formation sandstones.

Gas-Water Production of a Continental Tight-Sandstone Gas Reservoir under Different Fracturing Conditions

A numerical model of hydraulic fracture propagation is introduced for a representative reservoir(Yuanba continental tight sandstone gas reservoir in Northeast Sichuan).Different parameters are considered,i.e.,the interlayer stress difference,the fracturing discharge rate and the fracturing fluid viscosity.The results show that these factors affect the gas and water production by influencing the fracture size.The interlayer stress difference can effectively control the fracture height.The greater the stress difference,the smaller the dimensionless reconstruction volume of the reservoir,while the flowback rate and gas production are lower.A large displacement fracturing construction increases the fracture-forming efficiency and expands the fracture size.The larger the displacement of fracturing construction,the larger the dimensionless reconstruction volume of the reservoir,and the higher the fracture-forming efficiency of fracturing fluid,the flowback rate,and the gas production.Low viscosity fracturing fluid is suitable for long fractures,while high viscosity fracturing fluid is suitable for wide fractures.With an increase in the fracturing fluid viscosity,the dimensionless reconstruction volume and flowback rate of the reservoir display a non-monotonic behavior,however,their changes are relatively small.

Production forecasting methods for different types of gas reservoirs

Hydrocarbon production in oil and gas fields generally progresses through stages of production ramp-up,plateau(peak),and decline during field development,with the whole process primarily modeled and forecasted using lifecycle models.SINOPEC's conventional gas reservoirs are dominated by carbonates,low-permeability tight sandstone,condensate,volcanic rocks,and medium-to-high-permeability sandstone.This study identifies the optimal production forecasting models by comparing the fitting coefficients of different models and calculating the relative errors in technically recoverable reserves.To improve forecast precision,it suggests substituting exponential smoothing method-derived predictions for anomalous data caused by subjective influences like market dynamics and maintenance activities.The preferred models for carbonate gas reservoir production forecasts are the generalized Weng's,Beta,Class-I generalized mathematical,and Hu-Chen models.The Vapor pressure and Beta models are optimal for forecasting the annual productivity of wells(APW)from gas-bearing low-permeability tight sandstone reservoirs.The Wang-Li,Beta,and Yu QT tb models are apt for moderate-to-small-reserves,single low-permeability tight sandstone gas reservoirs.The Rayleigh,Hu-Chen,and generalized Weng's models are suitable for condensate gas reservoirs.For medium-to-high-permeability sandstone gas reservoirs,the lognormal,generalized gamma,and Beta models are recommended.

Authigenic clay minerals and calcite dissolution influence reservoir quality in tight sandstones:Insights from the central Junggar Basin,NW China

Authigenic clays and calcite cements are important in the development of reservoir tightness and the formation of hydrocarbon sweet spots.We investigated Jurassic low-permeability sandstone reservoirs in the central Junggar Basin,NW China,using petrography,mineralogy,porosity,and permeability assessment,and stable C and O isotope analysis to ascertain the influence of authigenic clays and calcites on reservoir quality.Here,we establish the properties and diagenetic processes of the reservoir sandstones,and construct a generalizable model of reservoir quality.The results show that the sandstones are mainly litharenite and feldspathic litharenite and can be classified into ductile-lithic-rich sandstones and ductile-lithic-poor sandstones according to rock composition.The ductile-lithic-rich sandstones are tight(mean porosity?7.31%;mean permeability?0.08 mD)as a result of intense compaction.In contrast,the ductile-lithic-poor sandstones can be classified into five types according to diagenetic process.The formation of favorable hydrocarbon reservoir properties is closely related to the presence of authigenic clays and dissolution of calcite.In particular,kaolinite fills intergranular pores,thereby blocking pore space and reducing reservoir quality.Chlorite coating resists compaction and limits the formation of quartz overgrowths,thereby preserving pore space and enhancing reservoir quality.Calcite controls reservoir quality through both precipitation and dissolution.Calcite precipitation results in reduced reservoir quality,whereby early calcites that were precipitated in formation water resist compaction and provide the basis for subsequent dissolution and late precipitation,whereas dissolution of calcite in mesodiagenesis improves reservoir quality.A generalized model is formulated by relating diagenetic facies types to depth and porosity,providing a reference for other similar reservoirs.Our data suggest that deeply buried tight sandstones can be exploration prospects under favorable conditions involving the presence of authigenic clays and dissolution of calcite,as in the central Junggar Basin of this study.

Quantitative characterization of tight gas sandstone reservoirs using seismic data via an integrated rock-physics-based framework

Seismic characterizing of tight gas sandstone (TGS) reservoirs is essential for identifying promising gas-bearing regions. However, exploring the petrophysical significance of seismic-inverted elastic properties is challenging due to the complex microstructures in TGSs. Meanwhile, interbedded structures of sandstone and mudstone intensify the difficulty in accurately extracting the crucial tight sandstone properties. An integrated rock-physics-based framework is proposed to estimate the reservoir quality of TGSs from seismic data. TGSs with complex pore structures are modeled using the double-porosity model, providing a practical tool to compute rock physics templates for reservoir parameter estimation. The VP/VS ratio is utilized to predict the cumulative thickness of the TGS reservoirs within the target range via the threshold value evaluated from wireline logs for lithology discrimination. This approach also facilitates better capturing the elastic properties of the TGSs for quantitative seismic interpretation. Total porosity is estimated from P-wave impedance using the correlation obtained based on wireline log analysis. After that, the three-dimensional rock-physics templates integrated with the estimated total porosity are constructed to interpret microfracture porosity and gas saturation from velocity ratio and bulk modulus. The integrated framework can optimally estimate the parameters dominating the reservoir quality. The results of the indicator proposed based on the obtained parameters are in good agreement with the gas productions and can be utilized to predict promising TGS reservoirs. Moreover, the results suggest that considering microfracture porosity allows a more accurate prediction of high-quality reservoirs, further validating the applicability of the proposed method in the studied region.

Hydrocarbon indication in Rio Bonito Formation sandstone:Implication for CO_(2)storage in São Paulo,Brazil

São Paulo State has witnessed CO_(2)storage-based investigations considering the availability of suitable geologic structures and proximity to primary CO_(2)source sinks related to bioenergy and carbon capture and storage(BECCS)activities.The current study presents the hydrocarbon viability evaluations and CO_(2)storage prospects,focusing on the sandstone units of the Rio Bonito Formation.The objective is to apply petrophysical evaluations with geochemical inputs in predicting future hydrocarbon(gas)production to boost CO_(2)storage within the study location.The study used data from eleven wells with associated wireline logs(gamma ray,resistivity,density,neutron,and sonic)to predict potential hydrocarbon accumulation and fluid mobility in the investigated area.Rock samples(shale and carbonate)obtained from depths>200 m within the study location have shown bitumen presence.Organic geochemistry data of the Rio Bonito Formation shale beds suggest they are potential hydrocarbon source rocks and could have contributed to the gas accumulations within the sandstone units.Some drilled well data,e.g.,CB-1-SP and TI-1-SP,show hydrocarbon(gas)presence based on the typical resistivity and the combined neutron-density responses at depths up to 3400 m,indicating the possibility of other hydrocarbon members apart from the heavy oil(bitumen)observed from the near-surface rocks samples.From the three-dimensional(3-D)model,the free fluid indicator(FFI)is more significant towards the southwest and southeast of the area with deeper depths of occurrence,indicating portions with reasonable hydrocarbon recovery rates and good prospects for CO_(2)injection,circulation and permanent storage.However,future studies based on contemporary datasets are required to establish the hydrocarbon viability further,foster gas production events,and enhance CO_(2)storage possibilities within the region.

The Upper Jurassic sediments,Marib-Shabwa Basin,Yemen:Lithofacies aspects and sequence stratigraphic analysis

The present study is devoted to understanding the evolution of the Upper Jurassic Sab'atayn Formation in the Marib-Shabwa Basin,Yemen,through a sequence stratigraphic analysis based on integrating datasets of sedimentology,seismic sections,and well logs.The Sab'atayn Formation(Tithonian age)is represented by a series of clastic and evaporites that were deposited under fluvio-deltaic to prodeltaic settings.It is divided into four members including Yah(at the base),upwards to Seen,Alif,and Safir at the top.Two third-order depositional sequences were determined for the Tithonian succession which were separated by three sequence boundaries.These sequences were classified into their systems tracts signifying several sedimentation patterns of progradational,aggradational,and retrogradational parasequence sets.The first depositional sequence corresponds to the early-middle Tithonian Yah and Seen units that can be classified into lowstand,transgressive,and highstand systems tracts.The second sequence comprises the late Tithonian Alif unit that can be subdivided into transgressive and highstand systems tracts.The sandy deposits of the Alif Member(highstand deposits)represent the most productive hydrocarbon reservoir in the basin.The Upper Jurassic sediments in the study area were resulted from a combination of eustatic and tectonic effects.

Brittleness index and seismic rock physics model for anisotropic tight-oil sandstone reservoirs

Brittleness analysis becomes important when looking for sweet spots in tightoil sandstone reservoirs. Hence, appropriate indices are required as accurate brittleness evaluation criteria. We construct a seismic rock physics model for tight-oil sandstone reservoirs with vertical fractures. Because of the complexities in lithology and pore structure and the anisotropic characteristics of tight-oil sandstone reservoirs, the proposed model is based on the solid components, pore connectivity, pore type, and fractures to better describe the sandstone reservoir microstructure. Using the model, we analyze the brittleness sensitivity of the elastic parameters in an anisotropic medium and establish a new brittleness index. We show the applicability of the proposed brittleness index for tight-oil sandstone reservoirs by considering the brittleness sensitivity, the rock physics response characteristics, and cross-plots. Compared with conventional brittleness indexes, the new brittleness index has high brittleness sensitivity and it is the highest in oil-bearing brittle zones with relatively high porosity. The results also suggest that the new brittleness index is much more sensitive to elastic properties variations, and thus can presumably better predict the brittleness characteristics of sweet spots in tight-oil sandstone reservoirs.

Mesozoic Reservoir Predictionin the Longdong Loess Plateau

This paper summarizes a set of interpretation technologies for Mesozoic sandstone reservoir prediction in the Longdong loess plateau, such as seismic sequence processing and interpretation based on generalized S transform, the eroded paleo-geomorphology interpretation of the top of the Triassic and a variety of lateral reservoir predictions. The effects of employing these technologies are compared and analyzed, as well. The research results show that seismic sequence processing interpretation technology based on generalized S transform can distinguish 3ms (about the thickness of 6 m)sequence interface. Consequently the technology can ascertain the distribution of a sand body of the formation Ch 8 and expand the exploration area of the Xifeng oil field in the Longdong area.

Detailed sedimentary facies of a sandstone reservoir in the eastern zone of the Sulige gas field, Ordos Basin

Given sustaining exploration, the eastern zone of the Sulige gas field may soon become a key area of exploitation. In order to explore its genesis, types and distribution of the reservoir sandstones in the eastern zone of this gas field, we focused in our study on the provenance and detailed sedimentary facies of sandstone of the He8 （the eighth part of the Shihezi formation, Permian system） and Shanxil （the first part of the Shanxi formation, Permian system） members, based on core observations, analyses in petrography, granularity and logging. The results show that： 1） the sandstone provenance of Shanxil and He8 in the eastern zone of the Sulige gas field is from the north of the Ordos Basin, characterized by dual directions from the north and northeast. 2） The He8 and Shanxil members were deposited in a fluvial-delta sedimentary system. The He8 was mainly deposited in braided rivers, in- cluding braided channels, channel bars, levee and floodplain sub-environments, whereas the Shanxil Member was deposited in braided rivers and deltas, including braided channels, channel bars, floodplains, tributaries and inter-tributary sub-environments. 3） Sedimentary facies bands migrated in drastic fashion towards the basin from the Shanxil to the He8 Member. Base levels of sedi- mentation generally present a trend of small increases in-amplitude, large decreasing amplitudes and slow and gradual Increases. 4） The continuity of the reservoir sandbodies along the source direction is better than that perpendicular to the direction. Compared with Shanxil, both dimensions and continuity of the sandbodies in He8 are better from which we conclude that it is the most fa- vorable part of the reservoir.

Depositional and Diagenetic Controls on Sandstone Reservoirs with Low Porosity and Low Permeability in the Eastern Sulige Gas Field, China

In order to determine the genesis and the factors that control the low-porosity and low- permeability sandstone reservoirs in the eastern Sulige Gas Field in the Ordos Basin, systematic studies on the sedimentary facies and diagenesis were conducted by means of analysis of cores, thin sections, fluid inclusions, X-ray diffraction, cathode luminescence and scanning electron microscope. It was found that the sand bodies of the major gas reservoirs in the Shan1 section （P1S1） and the He8 section （P2H8） were formed during the Permian as sedimentary facies such as braided-channel bars, braided-river channels and point bars of a meandering river. Four types of diagenetic facies developed subsequently： in order from the best to the poorest properties these are type A （weak compaction, early calcite cement-chlorite film facies）, type B （moderate compaction, quartz overgrowth-feldspar corrosion-kaolinite filling facies）, type C （strong compaction, late calcite cement-quartz corrosion facies） and type D （matrix filling and strong compaction facies）. This diagenesis is undoubtedly the main reason for the poor reservoir properties of sandstone reservoirs, but the sedimentary facies are the underlying factors that greatly affect the diagenesis and thus the reservoir performance. Favorable diagenetic facies developed mainly in relatively small lithofacies such as braided-river channels, channel bars and point bars. The vertical distribution of the physical properties and the diagenetic facies of the reservoirs are related to the stratigraphic succession. Most of the sandstones between mudstones and thin beds of sandstone are unfavorable diagenetic facies. Analyses indicate that siliceous cementation can hardly be stopped by hydrocarbon filling. Authigenic chlorite could hardly protect the primary porosity. It not only occupies pore space, but also blocks pathways through sandstone reservoirs, so that it has significant influence on the permeability. Authigenic chlorite cannot be used as a marker for a specific sedimentary facies because it can be formed in different sedimentary facies, but it indicates high hydrodynamic conditions and presence of favorable reservoirs.

Siliceous Cementation of Chlorite-Coated Grains in the Permian Sandstone Gas Reservoirs,Ordos Basin

Objective It has long been controversial that whether authigenic chlorite coatings in sandstone reservoirs can prevent precipitation of siliceous cements. It is commonly believed that chlorite coatings （also called chlorite films, chlorite linings, or chlorite rims） may prevent quartz overgrowth, and thus help the preservation of original pores in sandstone reservoirs. Recently, however, this assumption has been challenged by reservoir geologists. This dispute cannot be solved by mere analysis of thin sections, nor by chemical equations and diagenesis analysis. The main objective of the present contribution is to shed light on this problem on the basis of sandstone samples from the Permian Shanxi and Shihezi Formations in the eastern part of the Sulige gas field, Ordos Basin in central China.

Sweet spot prediction in tight sandstone reservoir based on well-bore rock physical simulation

To establish the relationship among reservoir characteristics and rock physical parameters,we construct the well-bore rock physical models firstly,considering the influence factors,such as mineral composition,shale content,porosity,fluid type and saturation.Then with analyzing the change rules of elastic parameters along with the above influence factors and the cross-plots among elastic parameters,the sensitive elastic parameters of tight sandstone reservoir are determined,and the rock physics template of sweet spot is constructed to guide pre-stack seismic inversion.The results show that velocity ratio and Poisson impedance are the most sensitive elastic parameters to indicate the lithologic and gas-bearing properties of sweet spot in tight sandstone reservoir.The high-quality sweet spot is characterized by the lower velocity ratio and Poisson impedance.Finally,the actual seismic data are selected to predict the sweet spots in tight sandstone gas reservoirs,so as to verify the validity of the rock physical simulation results.The significant consistency between the relative logging curves and inversion results in different wells implies that the utilization of well-bore rock physical simulation can guide the prediction of sweet spot in tight sandstone gas reservoirs.

K-Ar Dating of Authigenic Illites and Its Applications to the Study of Hydrocarbon Charging Histories of Typical Sandstone Reservoirs in Tarim Basin, China

The Tarim Basin in China comprises eight sets of sandstone reservoirs, five of which are investigated in detail in this study. The main purpose of this study is to investigate the hydrocarbon charging histories of reservoirs by applying K-Ar dating of authigenic illites. The ages of authigenic illites from the Lower Silurian bituminous sandstones in the Central Uplift area range from 383.5 to 235.2 Ma, suggesting that the Silurian oil accumulations were formed from the late Caledonian till the late Hercynian. The ages of authigenic illites from the Upper Devonian Donghe Sandstone reservoirs range from 263.8 to 231.3 Ma, indicating that hydrocarbon accumulations within the Donghe sandstone were formed mainly in the late Hercynian. The authigenic illites ages from the Lower Jurassic Yangxia Group sandstones in the Yinan-2 gas reservoir (Yinan-2, Kuqa Depression) range from 28.1 to 23.9 Ma, suggesting that the initial hydrocarbon charging occurred in the Miocene. The ages of the authigenic illites from the Lower Cretaceous sandstones in the Akemomu gas field (Ake-1, Kashi Sag, Southwest Depression) range from 22.6 to 18.8 Ma, indicating a probable early oil accumulation or early migration of hydrocarbon within this area. The illites from the Paleogene sandstones in the Dina-2 gas reservoir (Dina-201, Kuqa Depression) have a detrital origin; they cannot be used to study the hydrocarbon charging histories. The ages of authigenic illites in the underlying Cretaceous sandstones in the same well (Dina-201) range from 25.5 to 15.5 Ma, indicating that hydrocarbon charging in this reservoir probably occurred within the Miocene. This study highlights the potential of applying K-Ar dating of authigenic illites to investigate the timing of hydrocarbon charging histories of the Tarim Basin reservoir sandstones.

Geochronological Records of Oil-Gas Accumulations in the Permian Reservoirs of the Northeastern Ordos Basin

Geochronology of oil-gas accumulation （OGA） is a challenging subject of petroleum geology in multi-cycle superimposed basins.By K-Ar dating of authigenic illite （AI） and fluid inclusion （FI） analysis combined with apatite fission track （AFT） thermal modeling,a case study of constraining the OGA times of the Permian reservoirs in northeast Ordos basin （NOB） has been conducted in this paper.AI dating of the Permian oil-gas-bearing sandstone core-samples shows a wide time domain of 178-108 Ma.The distribution of the AI ages presents 2-stage primary OGA processes in the Permian reservoirs,which developed in the time domains of 175-155 Ma and 145-115 Ma with 2-peak ages of 165 Ma and 130 Ma,respectively.The FI temperature peaks of the samples and their projected ages on the AFT thermal path not only present two groups with a low and a high peak temperatures in ranges of 90-78℃ and 125-118℃,respectively corresponding to 2-stage primary OGA processes of 162-153 Ma and 140-128 Ma in the Permian reservoirs,but also appear a medium temperature group with the peak of 98℃ in agreement with a secondary OGA process of c.～30 Ma in the Upper Permian reservoirs.The integrated analysis of the AI and FI ages and the tectono-thermal evolution reveals that the Permian reservoirs in the NOB experienced at least 2-stage primary OGA processes of 165-153 Ma and 140-128 Ma in agreement with the subsidence thermal process of the Mid-Early Jurassic and the tectono-thermal event of the Early Cretaceous.Then,the Upper Permian reservoirs further experienced at least 1-stage secondary OGA process of c.～30 Ma in coincidence with a critical tectonic conversion between the slow and the rapid uplift processes from the Late Cretaceous to Neogene.

Genesis Types and Diagenesis Compaction Mechanisms of Sandstone Rreservoirs in Dynamic Environments in Oil/Gas Basins in China

The diversity of sandstone diagenesis mechanisms caused by the complex geological conditions of oil/gas basins in China could hardly be reasonably explained by the traditional concept of burial diagenesis. Three genesis types of thermal diagenesis, tectonic diagenesis and fluid diagenesis are presented on the basis of the dynamic environment of the oil/gas basins and.the controlling factors and mechanisms of sandstone diagenesis. Thermal diagenesis of sandstone reservoirs is related not only to the effect of formation temperature on diagenesis, but also to the significant changes in diagenesis caused by geothermal gradients. The concept of thermal compaction is presented. Thermal compaction becomes weaker with increasing depth and becomes stronger at a higher geothermal gradient. At the same formation temperature, the sandstone porosity in the region with a lower geothermal gradient is e^0.077＋0.0042T times higher than that in the region with a higher geothermal gradient. Both sudden and gradual changes are observed in diagenetic evolution caused by structural deformation. Average sandstone compaction increased by 0.1051% for every 1.0MPa increase of lateral tectonic compressional stress, while late tectonic napping helped to preserve a higher porosity of underlying sandstone reservoir. Fluid diagenesis is a general phenomenon. The compaction caused by fluid properties is significant. The coarser the grain size, the stronger the fluid effect on compaction. The greater the burial depth, the weaker the fluid effect on compaction for the specific reservoir lithology and the greater the difference in the fluid effects on compaction between different grain sizes.

Three-Dimensional Modelling of a Multi-Layer Sandstone Reservoir： the Sebei Gas Field, China

Multi-layer sandstone reservoirs occur globally and are currently in international production. The 3D characteristics of these reservoirs are too complicated to be accurately delineated by general structural-facies-reservoir modelling. In view of the special geological features, such as the vertical architecture of sandstone and mudstone interbeds, the lateral stable sedimentation and the strong heterogeneity of reservoir poroperm and fluid distribution, we developed a new three-stage and six-phase procedure for 3D characterization of multi-layer sandstone reservoirs. The procedure comprises two-phase structural modelling, two-phase facies modelling and modelling of two types of reservoir properties. Using this procedure, we established models of the formation structure, sand body structure and microfacies, reservoir facies and properties including porosity, permeability and gas saturation and provided a 3D fine-scale, systematic characterization of the Sebei multi-layer sandstone gas field, China. This new procedure, validated by the Sebei gas field, can be applied to characterize similar multi-layer sandstone reservoirs.

Detrital K-feldspar^(40)Ar/^(39)Ar Ages:Source Constraints of the Lower Miocene Sandstones in the Pearl River Mouth Basin,South China Sea

The South China Sea began to outspread in the Oligocene. A great quantity of terraneous detritus was deposited in the northern continental shelf of the sea, mostly in Pearl River Mouth Basin, which constituted the main paleo-Pearl River Delta. The delta developed for a long geological time and formed a superimposed area. Almost all the oil and gas fields of detrital rock reservoir distribute in this delta. Thirty-three oil sandstone core samples in the Zhujiang Formation, lower Miocene （23-16 Ma）, were collected from nine wells. The illite samples with detrital K feldspar （Kfs） separated from these sandstone cores in four sub-structural belts were analysed by the high-precision 40Ar/39Ar laser stepwise heating technique. All 33 illite 40Ar/39Ar data consistently yielded gradually rising age spectra at the low-temperature steps until reaching age plateaus at mid-high temperature steps. The youngest ages corresponding to the beginning steps were interpreted as the hydrocarbon accumulation ages and the plateau ages in mid-high temperature steps as the contributions of the detrital feldspar representing the ages of the granitic parent rocks in the provenances. The ages of the detrital feldspar from the Zhujiang Formation in the four sub-structural belts were different： （1） the late Cretaceous ages in the Lufeng 13 fault structural belt; （2） the late Cretaceous and early Cretaceous-Jurassic ages in the Huizhou 21 buried hill-fault belt; （3） the Jurassic and Triassic ages in the Xijiang 24 buried hill-fault belt; and （4） the early Cretaceous - late Jurassic ages in the Panyu 4 oil area. These detrital feldspar 4~Ar/39Ar ages become younger and younger from west to east, corresponding to the age distribution of the granites in the adjacent Guangdong Province, Southern China.

Determination of microscopic waterflooding characteristics and influence factors in ultra-low permeability sandstone reservoir

Actual sandstone micromodel was used in this work to conduct the microscopic waterflooding experiment of ultra-low sandstone reservoir,since the inside seepage characteristics of microscopic waterflooding process of Chang 8 ultra-low permeability sandstone reservoir of Upper Triassic Yanchang formation in Huaqing region of the Ordos Basin,China is difficult to observe directly.Combined with physical property,casting thin sections,constant-rate mercury injection capillary pressure and nuclear magnetic resonance,the influence of reservoir property on the waterflooding characteristics in pores were analyzed and evaluated.Seepage paths of waterflooding characteristics were divided into four types:homogeneous seepage,reticular-homogeneous seepage,finger-reticular seepage and finger-like seepage,the waterflooding efficiency of which decreases in turn.More than 70%of residual oil occurs as flowing-around seepage and oil film.Physical property,pore structure and movable fluid characteristics are all controlled by digenesis and their impacts on waterflooding efficiency are in accordance.Generally,the pore throat radius size and distribution and movable fluid percentage are closely related to waterflooding law.

Influence of strong preformed particle gels on low permeable formations in mature reservoirs

In mature reservoirs,the success of preformed particle gel（PPG） treatment rests primarily on the ability of the PPG to reduce and/or plug the high permeable formations,but not damage the low permeable formations.Static test models（filtration test model and pressure test model）were used to determine the effect of PPG on low permeable formations.This work used a strong preformed particle gel,Daqing（DQ） gel made by a Chinese company.The particle gel sizes were ranged from 30 to 120 mesh for this work.PPGs are sized in a millimeter or micrometer,which can absorb over a hundred times their weight in liquids.The gel strength was approximately 6500 Pa for a completely swollen PPG with 1 %（weight percentage） NaCl solution（brine）.0.05 %,1 %,and 10 % NaCl solutions were used in experiments.Sandstone core permeability was measured before and after PPG treatments.The relationship between cumulative filtration volumes versus filtration times was determined.The results indicate that DQ gels of a particle size of 30–80 mesh did not damage the cores of a low permeability of 3–25 m D.The DQ gels of a smaller particle size ranging from 100 to 120 mesh damaged the core and a cake was formed on the core surface.The results also indicate that more damage occurred when a high load pressure（400 psi） was applied on the high permeability cores（290–310 m D）.The penetration of the particle gelsinto the low permeable formations can be decreased by the best selection of gel types,particle sizes,and brine concentrations.