Enhancing fly ash utilization in backfill materials treated with CO_(2)carbonation under ambient conditions

The environmental concerns resulting from coal-fired power generation that produces large amounts of CO_(2)and fly ash are of great interest.To mitigate,this study aims to develop a novel carbonated CO_(2)-fly ash-based backfill(CFBF)material under ambient conditions.The performance of CFBF was investigated for different fly ash-cement ratios and compared with non-CO_(2)reacted samples.The fresh CFBF slurry conformed to the Herschel-Bulkley model with shear thinning characteristics.After carbonation,the yield stress of the fresh slurry increased significantly by lowering fly ash ratio due to gel formation.The setting times were accelerated,resulting in approximately 40.6%of increased early strength.The final strength decreased when incorporating a lower fly ash ratio(50%and 60%),which was related to the existing heterogeneous pores caused by rapid fluid loss.The strength increased with fly ash content above 70%because additional C-S(A)-H and silica gels were characterized to precipitate on the grain surface,so the binding between particles increased.The C-S(A)-H gel was developed through the pozzolanic reaction,where CaCO_(3)was the prerequisite calcium source obtained in the CO_(2)-fly ash reaction.Furthermore,the maximum CO_(2)uptake efficiency was 1.39 mg-CO_(2)/g-CFBF.The CFBF material is feasible to co-dispose CO_(2)and fly ash in the mine goaf as negative carbon backfill materials,and simultaneously mitigates the strata movement and water lost in post-subsurface mining.

Adsorption of residual amine collector HAY from aqueous solution by refined carbon from coal fly ash and activated carbon

Refined carbon(RC) derived from coal fly ash(CFA) as well as powdered activated carbon(PAC) was investigated as adsorbent to remove residual amine collector HAY from aqueous solution.The RC and PAC were characterized by scanning electron microscopy(SEM),surface area measurement,Zeta potential measurement and Fourier transform infrared(FTIR) spectroscopy.The effect factors and mechanisms of HAY adsorption onto RC and PAC were studied in detail.The results show that the experimental kinetic data agree well with the pseudo second-order equation,and the Langmuir isotherm model is found to be more appropriate to explicate the experimental equilibrium isotherm results than the Freundlich model.The adsorption capacities of PAC and RC increase with pH.It is found that alkaline condition is conducive to the adsorption of HAY onto PAC and RC and the adsorption efficiency of RC is close to PAC at pH near 11.Zeta potential variation of adsorbents suggests that HAY generates electrostatic adsorption onto RC and PAC.FTIR analysis shows that the adsorption is dominantly of a physical process.The Box-Behnken design optimization conditions of process are RC 1 g/L,pH 11,temperature 302 K and initial HAY concentration 100 mg/L.Under these conditions,the measured adsorption ratio and adsorption capacity are 87.91%and 87.91 mg/g,respectively.Thus,the RC is considered to be a potential adsorbent for the removal of residual amine from aqueous solution.

Enhanced visible-light photocatalytic oxidation capability of carbon-doped TiO_2 via coupling with fly ash

A carbon‐doped TiO2/fly ash support(C‐TiO2/FAS)composite photocatalyst was successfully synthesized through sol impregnation and subsequent carbonization.The carbon dopants were derived from the organic species generated during the synthesis of the C‐TiO2/FAS composite.A series of analytical techniques,such as scanning electron microscopy(SEM),attenuated total reflection‐Fourier transform infrared(ATR‐FTIR)spectroscopy,X‐ray photoelectron spectroscopy(XPS),and ultraviolet‐visible diffuse reflectance spectroscopy(UV‐Vis DRS),were used to characterize the properties of the prepared samples.The results indicated that C‐TiO2 was successfully coated on the FAS surface.Coupling between C‐TiO2 and FAS resulted in the formation of Si–O–C and Al–O–Ti bonds at their interface.The formation of Si–O–C and Al–O–Ti bonds gave rise to a positive shift of the valence band edge of C‐TiO2 and enhanced its oxidation capability of photogenerated holes as well as photodegradation efficiency of methyl orange.Moreover,the C‐TiO2/FAS photocatalyst exhibited favorable reusability and separability.This work may provide a new route for tuning the electronic band structure of TiO2.

Vapor-phase elemental mercury adsorption by residual carbon separated from fly ash

The adsorption capacity for vapor-phase elemental mercury(Hg0) of residual carbon separated from fly ash was studied in an attempt for the control of elemental mercury emissions from combustion processes. At low mercury concentrations(<200 μg/m3), unburned carbon had higher adsorption capacity than commercial activated carbon. The adsorbality of unburned carbon was also found to be source dependent. Isotherms of FS carbon(separated from fly ash of a power plant of Shishi in Fujian Province) were similar to those classified as typeⅡ. Isotherms of XJ carbon(separated from fly ash of a power plant of Jingcheng in Shanxi Province) were more like those classified as type Ⅲ. Due to the relatively low production costs, these residual carbons would likely be considerably more cost-effective for the full-scale removal of mercury from combustion flue gases than other technology.

Research on Existing Pattern of Carbon and Its Removal from Fly Ash

Fly ash is a fine and dispersed powder discharged from power station after the coal being burned. With the deepening of people’s recognition about the pollution problem of fly ash, the ways of utilizing fly ash are gradually increasing. Utilizing value of fly ash is closely related to the unburned carbon content.On the basis of analysis of modern testing method,a fundamental thinking is theoretically posed for decreasing unburned carbon content from fly ash by a dry removing carbon technology. The triboelectric separation method shown that the above mentioned thinking of dry removing carbon from fly ash is practical.

Characterization of LDPE Reinforced with Calcium Carbonate—Fly Ash Hybrid Filler

The synergetic effect of calcium carbonate (CC)-fly ash (FA) hybrid filler particles on the mechanical and physical properties of low density polyethylene (LDPE) has been investigated. Low density polyethylene is filled with varying weight percentages of FA and CC using melt casting. Composites are characterized for mechanical, thermal, microstructural and physical properties. Results show that the flexural strength increases with increases in FA content of the hybrid filler. It is evident from the study that to achieve optimum density a certain combination of both fillers need to be used. The optimum combination of CC and FA for a higher density (1.78 g/cm3) is found to be at 20 wt% FA and 30 wt% CC. An increase of 7.27% in micro-hardness over virgin polyethylene is obtained in composites with 10 wt% FA and 40 wt% CC. The presence of higher amount of CC is seen to be detrimental to the crystallinity of composites. X-ray, FTIR and DSC results show that composite with 45 wt% CC and 5 wt% FA exhibits a typical triclinic polyethylene structure indicating that the composite is amorphous in nature. There was the synergy between FA and CC fillers on flexural strength and crystallinity of composite. However, the fillers show the antagonistic effect on energy at peak and micro-hardness.

Analysis of Carbon Nanotubes Produced by Pyrolysis of Composite Film of Poly (Vinyl Alcohol) and Modified Fly Ash

We determined the catalytic function of chemically modified fly ash (MFA) for the growth of carbon nanotube (CNT) ropes with ~54% yield by the pyrolysis of the composite film of poly (vinyl alcohol) (PVA) at 500°C for 10 min under 2 L/min flow of nitrogen. Fly ash was treated with 2M sodium hydroxide to have MFA and used with PVA to fabricate the composite film by aqua casting. CNT was analyzed using SEM, TEM, XPS and Raman spectroscopy. The growths of CNT on MFA surfaces were visualized with different geometric self-assembly, e.g., bundles of CNT in ropes, twisted ropes, Y-branch ropes and staked-cone sheet. Thus, the mixtures of CNT ropes and MFA are a potential filler material for fabricating composites with polymer and metal.

Growth of Carbon Nanotubes by Pyrolysis of Composite Film of Poly (Vinyl Alcohol) and Modified Fly Ash

We found carbon nanotube (CNT) materials by the pyrolysis of the composite film of poly (vinyl alcohol) (PVA) reinforced with modified fly ash (FA) at 500°C for 10 min under 2 L/min flow of nitrogen. Fly ash was treated with 2M sodium hydroxide and used with PVA to fabricate the composite film by aqua casting. CNT materials were analyzed using XPS, Raman, SEM and TEM. The admixtures of CNT materials and FA are a potential filler material for fabricating composites with polymer and metal. The process is an eco-friendly recycling paradigm for using value-added advanced products for the proper management of sustainable waste materials, plastic and FA.

Principal Chemical Properties of Artificial Soil Composed of Fly Ash and Furfural Residue

To solve soil shortage in reclaiming subsided land of coal mines, the principal chemical properties of artificial soil formed by mixing organic furfural residue and inorganic fly ash were examined. The results indicated that the artificial soil was suitable for agriculture use after irrigation and desalination, the available nutrients in the artificial soil could satisfy the growth demand of plants, and the pH tended to the neutrality.

Comparisons of Fly Ash and Deposition Between Air and Oxy-Fuel Combustion in Bench-Scale Fluidized Bed with Limestone Addition

In Oxy-fuel circulating fluidized bed,the residual Ca O particles may react with high concentration of CO2 in flue gas to form bonded deposit on heat transfer surfaces in backpass when limestone is used as a sorbent to capture SO2.In this paper,experiments were designed on ash deposition in a bench-scale fluidized bed under oxy-fuel and air atmosphere. A novel ash deposit sampling probe was used to simulate the tubes of tail surfaces.The chemical composition of fly ash and ash deposit from both air-firing and oxy-fuel firing cases were analyzed by Inductively Coupled Plasma-Atomic Emission Spectrometry( ICP-AES) and Scanning Electron Microscopy( SEM),respectively. The degrees of carbonation reaction of ash deposits were measured by Thermo Gravimetric Analysis. The results showed that there are distinct differences in fly ash deposition rate between oxy-fuel and air firing cases,and oxy-fuel combustion with limestone addition can affect chemical composition of fly ash and ash deposit,especially for elements of Ca,Na,K,and S. However,the carbonation reaction degree of ash deposits is found weak,which is due to the relatively low Ca O content in ash deposit or not long enough of the sampling time.

Main influencing factors and coal fly ash characteristics of gasoues fuel reburning process

The unburned carbon concentration in fly ash and the influence of main factors on the reduction of nitrogen oxides during gaseous fuel reburning process were experimentally studied in a 36 kW down-fired furnace when five typical coals with different qualities were served as the primary fuel. It is found that the higher nitrogen oxide reduction efficiency can be obtained by reburning process when the coal used as the primary fuel contains more volatile matter. But under the optimizational operating conditions, both above 50% nitrogen oxide reduction and low carbon loss can be achieved by reburning process even though the primary fuel is the low-volatile coal. The experimental results show that the reasonable residence time in reburn zone is 0.6-0.9 s, the appropriate gaseous reburn fuel percentage is 10%-15% and the optimal average excess air coefficient in reburn zone is 0.8-0.9. These results extend the ranges of the key parameter values for reburning process with respect to that the low-volatile coals are used as the primary fuel.

Effect of MSWI Fly Ash and Incineration Residues on Cement Performances

The activities of municipal solid waste incineration （MSWI） fly ash and incineration residues were studied contrastively, through the component analysis and the activity ratio tests. The mechanical properties, hydration mechanism and leaching toxicity of the hardened cement paste mixing with MSWI fly ash and incineration residues were investigated. The experimental results indicated that the active constituents （CaO＋Al2O3＋Fe2O3） in MSWI fly ash were higher than those in incineration residues. Therefore the activity ratio of MSWI fly ash was 43.58%, twice as much as that of incineration residues. Meanwhile, the hydration of cement was delayed by mixing with MSWI fly ash and incineration residues, which also reduced the cement strength markedly. By adding with exceeding 20% MSWI fly ash, the specimens expanded and microcracks appeared. The leaching toxicities of cement pasted mixed with MSWI fly ash and incineration residues were lower than the Chinese national standard. Accordingly the cement mixed by MSWI fly ash and incineration residues can be considered as the environment-friendly materials.

Accelerated Carbonation Assessment of High-Volume Fly Ash Concrete

The issue of concrete carbonation has gained importance in recent years due to the increase use in supplementary cementing materials (SCMs) in concrete mixtures. While there is general agreement that concrete carbonation progresses at maximum at a relative humidity of about 60%, the rate may differ in the case of cements blended with SCMs, especially with high-volume fly ash replacements. In this study, the effect of high-volume fly ash concrete exposed to low ambient relative humidity (RH) conditions (57%) and accelerated carbonation (4% CO2) is investigated. Twenty-three concrete mixtures were produced varying in cementitious contents (310, 340, 370, and 400 kg/m3), water-to-cementitious materials ratio (0.45 and 0.50), and fly ash content (0%, 15%, 30%, and 50%) using a low and high-calcium fly ash. The specimens were allowed 1 and 7 days of moist curing and monitored for their carbonation rate and depth through phenolphthalein measurements up to 105 days of exposure. The accelerated carbonation test results indicated that increasing the addition of fly ash also led to increasing the depth of carbonation. Mixtures incorporating high-calcium fly ash were also observed to be more resistant against carbonation than low-calcium fly ash due to the higher calcium oxide (CaO) content. However, mixtures incorporating high-volume additions (50%) specimens were fully carbonated regardless of the type of fly ash used. It was evident that the increase in the duration of moist curing from 1 day to 7 days had a positive effect, reducing the carbonation depth for both plain and blended fly ash concrete mixes, however, this effect was minimal in high-volume fly ash mixtures. The results demonstrated that the water-to-cementitious ratio (W/CM) had a more dramatic impact on carbonation resistance than the curing age for mixtures incorporating 30% or less fly ash replacement, whereas those mixtures incorporating 50% showed minor differences regardless of curing age or W/CM. Based on the compressive strength results, carbonation depth appeared to decrease with increase in compressive strength, but this correlation was not significant.

Toughness Improvement of Geothermal Well Cement at up to 300^&deg;C: Using Carbon Microfiber

This study aimed at assessing the usefulness of carbon microfiber (CMF) in improving the compressive-toughness of sodium metasilicate-activated calcium aluminate/Class F fly ash foamed cement at hydrothermal temperatures of up to 300&deg;C. When the CMFs came in contact with a pore solution of cement, their surfaces underwent alkali-caused oxidation, leading to the formation of metal (Na, Ca, Al)-complexed carboxylate groups. The extent of this oxidation was enhanced by the temperature increase, corresponding to the incorporation of more oxidation derivatives at higher temperatures. Although micro-probe examinations did not show any defects in the fibers, the enhanced oxidation engendered shrinkage of the interlayer spacing between the C-basal planes in CMFs, and a decline in their thermal stability. On the other hand, the complexed carboxylate groups present on the surfaces of oxidized fibers played a pivotal role in improving the adherence of fibers to the cement matrix. Such fiber/cement interfacial bonds contributed significantly to the excellent bridging effect of fibers, resistance to the cracks development and propagation, and to improvement of the post-crack material ductility. Consequently, the compressive toughness of the 85&deg;-, 200&deg;-, and 300&deg;C-autoclaved foamed cements reinforced with 10 wt% CMF was 2.4-, 2.9-, and 3.1-fold higher than for cement without the reinforcement.

Modeling mercury adsorption on carbon particles in simulated flue gas

A model was developed to describe the adsorption characteristic of mercury in flue gas based on one residual carbon sample and one activated carbon sample. The differential equations were established with mass balance of mercury in the gas phase and in the solid phase. Then the model was solved using a Matlab program with a Runge-Kutta process. The mercury adsorption isotherms of these two adsorbents were obtained by breakthrough column experiments. The results show that at low gas phase mercury concentrations （ 〈 0. 3 mg/ m^3）, the adsorption equilibrium of residual carbon is in accord with the case of a type Ⅱ isotherm of the Freundich theory. Whereas the data of activated carbon falls into the Langmuir relationship, it is the case of a type Ⅲ isotherm. The experimental data were fitted to the Freundlich model by Matlab software. The variances of mercury concentration are smaller than 0. 81 which implies the agreement between measurements and simulation is quite agreeable considering the wide scatter of the measurements. This model is useful for forecasting mercury removal efficiency and is helpful to the mechanism analysis of mercury adsorption on carbon-based adsorbent.

Bond Durability of Carbon-Microfiber-Reinforced Alkali-Activated High-Temperature Cement Adhering to Carbon Steel

The study aims at evaluating the bond durability of a carbon microfiber (CMF)-reinforced alkali-activating calcium aluminate cement (CAC)/fly ash F (FAF) blend cementitious material adhering to carbon steel (CS) under stresses induced by a 350℃ heat-25℃ water cooling cycle. This cementitious material/CS joint sample was originally prepared in an autoclave at 300℃ under a pressure of 8.3 MPa. For comparison, two reference geothermal well cements, Class G modified with silica (G) and calciumaluminum phosphate (CaP), were employed as well reinforced with CMF. In the CAC/FAF blending cement systems, the CAC-derived cementitious reaction products preferentially adhered to CS surfaces, rather than that of FAF-related reaction products. CMF played a pivotal role in creating tough interfacial bond structure of cement layer adhering to CS. The bond toughness also was supported by the crystalline cementitious reaction products including sodalite, brownmillerite, and hedenbergite as major phases, and aragonite, boehmite, and garronite as minor ones. The brownmillerite as an interfacial reaction product between cement and CS promoted the chemical bonding of the cement to CS, while the other phases served in providing the attractive bonding of the cement to CS. The post-stress-test joint samples revealed the formation of additional brown-millerite, aragonite, and garronite, in particular brownmillerite as the major one. The combination of chemical bonding and self-advancing adherence behavior of the cement was essential for creating a better interfacial bond structure. A similar interfacial bond structure was observed with CaP. The crystalline phase composition of the autoclaved cement revealed apatite, zeolite, and ferrowyllieite as major reaction products, and aragonite and al-katoite as the minor ones. Ferrowyllieite was identified as cement/CS interfacial reaction product contributing to the chemical bond of cement, while the other phases aided in providing the attractive bond of cement. After a stress test, two phases, ferrowyllieite and aragonite, promoted the self-advancing adherence of cement to CS. However, the effectiveness of these phases in improving adherence performance of cement was less than that of CAC/FAF blend cement, reflecting the fact that the bond durability of CAC/FAF blend cement was far better than that of the CaP. In contrast, the autoclaved silica-modified G cement consisting of xonotlite, and 0.9 nm-to-bermorite and riversideite, with calcite as the crystalline reaction products, had no significant effect on improving the shear bond strength and the bond’s toughness. No interaction product with CS was found in the cement adhering to CS. After a stress test, the calcite phase acted only to promote the self-advancing adherence of cement, but its extent was minimal compared with that of the other cements, thereby resulting in poor bond durability.

Benefaction from Carbonation of Flue Gas CO_(2) as Coal Mining Filling

CO2 capturing, transport and sequestration by pressurized water dissolution and reacting by natural alkali lime and magnesia in coal fly ash or other sources become an industrial advantageous sequestration option resulting in green waste solutions or solid fines. Mg and Ca containing minerals are reacting with CO2 to form carbonates. Various types of fly ash materials may react with CO2 to form carbonate regarding ash composition and reaction parameters. Mineral sequestration of CO2 will also allow using the products in cement industry or as cement material in constructions with low cost. This paper discussed progress on coal mining filling by carbonation method using coal fly ash of Soma, Yatagan, Afsin Elbistan Power Stations. Other filler materials containing coal mine waste shale, fly ashes and foam concrete, and additives were searched for pretreatment methods to enhance cement reactivity;and in analyzing the structural changes to identify reaction paths and potential barriers.

基于高效解离-选择性絮凝耦合作用的煤气化渣提炭实验研究

煤气化渣是由煤气化工艺产生的一种富含铝硅酸盐、灰组分及残炭的大宗工业固体废弃物,其规模化生产对生态环境造成了严重的影响。因此,将煤气化渣进行炭-灰分离是实现其减量化、无害化和资源化利用的关键。以煤气化渣为研究对象,采用高效解离-选择性絮凝耦合作用的工艺,为实现煤气化渣更为合理、高效的资源化利用,减少煤气化渣带来的土壤、空气、水体资源等污染问题,对煤气化渣进行提炭实验研究。首先分析了煤气化渣的理化性质,其次采用单因素变量法探究了磨矿时间、pH、絮凝剂种类、絮凝剂用量、高速剪切转速对煤气化渣提炭实验的影响,以实现残余炭产品的高度富集。结果表明:原煤气化渣灰分质量分数为67.19%,普通湿筛筛上物料灰分质量分数为54.3%,当煤气化渣磨矿时间为5 s, pH为7,絮凝剂聚氧化乙烯用量为0.4 kg/t,在转速为4 000 r/min高速剪切15 min的条件下提炭效果最佳,最终可获得产率为26.6%、湿筛筛上灰分质量分数为43.3%的残炭产品。对比普通湿筛法,基于高效解离-选择性絮凝实验方法在普通湿筛的基础上灰分质量分数降低了11%,降灰效果明显。

Physicochemical Properties of Coal Gasification Fly Ash from Circulating Fluidized Bed Gasifier

The coal gasification fly ash(CGFA) is an industrial solid waste from coal gasification process and needs to be effectively disposed for environmental protection and resource utilization.To further clarify the feasibility of CGFA to prepare porous carbon materials,the physicochemical properties of ten kinds of CGFA from circulating fluidized bed(CFB) gasifiers were analyzed in detail.The results of proximate and ultimate analysis show that the CGFA is characterized with the features of near zero moisture content,low volatile content as low as 0.90%-9.76%,high carbon content in the range of 37.89%-81.62%,and ultrafine particle size(d50=15.8-46.2 μm).The automatic specific surface area(SSA) and pore size analyzer were used to detect the pore structure,it is found that the pore structure of CGFA is relatively developed,and part of the CGFA has the basic conditions to be used directly as porous carbon materials.From SEM images,the microscopic morphology of the CGFA is significantly different,and they basically have the characteristics of loose and porous structure.XRD and Roman spectroscopy were used to characterize the carbon structure.The result shows that the CGFA contains abundant amorphous carbon structure,and thus the CGFA has a good reactivity and a potential to improve pore structure through further activation.Through thermal gravimetric analysis,it can be concluded that the order of reactivity of the CGFA under CO_(2) atmosphere has a good correlation with the degree of metamorphism of the raw coal.The gasification reactivity of the CGFA is generally consistent with the change trend of micropores combined with the pore structure.According to the physicochemical properties,the CGFA has a good application prospect in the preparation of porous carbon materials.

Influence of SO_2 in incineration flue gas on the sequestration of CO_2 by municipal solid waste incinerator fly ash

The influence of CO2 content and presence of SO2 on the sequestration of CO2 by municipal solid waste incinerator （MSWI） fly ash was studied by investigating the carbonation reaction of MSWI fly ash with different combinations of simulated flue gas. The reaction between fly ash and 100% CO2 was relatively fast; the uptake of CO2 reached 87 g CO2/kg ash, and the sequestered CO2 could be entirely released at high temperatures. When CO2 content was reduced to 12%, the reaction rate decreased; the uptake fell to 41 g CO2/kg ash, and 70.7% of the sequestered CO2 could be released. With 12% CO2 in the presence of SO2, the reaction rate significantly decreased; the uptake was just 17 g CO2/kg ash, and only 52.9% of the sequestered CO2 could be released. SO2 in the simulated gas restricted the ability of fly ash to sequester CO2 because it blocked the pores of the ash.