Pure iron is one of the difficult-to-machine materials due to its large chip deformation,adhesion,work-hardening,and built-up edges formation during machining.This leads to a large workpiece deformation and challenge ...Pure iron is one of the difficult-to-machine materials due to its large chip deformation,adhesion,work-hardening,and built-up edges formation during machining.This leads to a large workpiece deformation and challenge to meet the required technical indicators.Therefore,under varying the grain size of pure iron,the influence of cutting speed,feed,and depth of cut on the cutting force,heat generation,and machining residual stresses were explored in the turning process to improve the machinability without compromising the mechanical properties of the material.The experimental findings have depicted that the influence of grain size on cutting force in the precision turning process is not apparent.However,the cutting temperature and residual stress of machining fine-grain iron were much smaller than the coarse grain at all levels of cutting parameters.展开更多
Background:Residual torque enhancement(rTE)is the increase in torque observed during the isometric steady state following active muscle lengthening when compared with a fixed-end isometric contraction at the same musc...Background:Residual torque enhancement(rTE)is the increase in torque observed during the isometric steady state following active muscle lengthening when compared with a fixed-end isometric contraction at the same muscle length and level of neuromuscular activation.In the rTE state,owing to an elevated contribution of passive force to total force production,less active force is required,and there is a subsequent reduction in activation.In vivo studies of rTE reporting an activation reduction are often performed using a dynamometer,where participants contract against a rigid restraint,resisting a torque motor.rTE has yet to be investigated during a position task,which involves the displacement of an inertial load with positional control.Methods:A total of 12 participants(6 males,6 females;age=22.8±1.1 years,height=174.7±8.6 cm,mass=82.1±37.7 kg;mean±SD)completed torque-and position-matching tasks at 60%maximum voluntary contraction for a fixed-end isometric contraction and an isometric contraction following active lengthening of the ankle dorsiflexors.Results:There were no significant differences in activation between torque-and position-matching tasks(p=0.743),with^27%activation reduction following active lengthening for both task types(p<0.001).Conclusion:These results indicate that rTE is a feature of voluntary,position-controlled contractions.These findings support and extend previous findings of isometric torque-control conditions to position-controlled contractions that represent different tasks of daily living.展开更多
Corrosion is a primary cause of the slippage of friction⁃type high⁃strength bolted(FHSB)T⁃stub connections.This paper attempts to quantify the residual capacity of FHSB T⁃stub connections with corroded nuts.Firstly,co...Corrosion is a primary cause of the slippage of friction⁃type high⁃strength bolted(FHSB)T⁃stub connections.This paper attempts to quantify the residual capacity of FHSB T⁃stub connections with corroded nuts.Firstly,corrosion simulation tests were conducted on 48 manually cut nuts to find out the relationship between the damage degree of nut section and the residual clamping force(RCF)of bolt.Then,static load tests were carried out on 24 FHSB T⁃stub connections with nuts of different degrees of damage to obtain the failure modes.By finite⁃element(FE)models,a comparative analysis was performed on the initial friction load(IFL)and ultimate strength(US)of each connection with corroded nuts.Finally,the parameters of 96 FE models for FHSB T⁃stub connections were analyzed and used to derive the calculation formulas for the degree of damage for each nut and the IFL and US of each connection.The results show that the RCF decay of a bolt is a quadratic function of the equivalent radius loss ratio and the shear failure after nut corrosion;the IFL of each connection had a clear linear correlation with the RCF of the corresponding bolts,and the correlation depends on the applied load and static friction on connecting plate interface induced by the clamping force;the static friction had little impact on the US of the connection;the proposed IFL and US formulas can effectively derive the residual anti⁃slip capacity of FHSB T⁃stub connections from the degree of damage of the corroded nut section.The research results provide a scientific basis for the replacement and maintenance of corroded bolts of FHSB T⁃stub connections.展开更多
An improved method for computing the three-dimensional(3 D)first-order Lagrangian residual velocity(uL)is estab-lished.The method computes tidal body force using the harmonic constants of the zeroth-order tidal curren...An improved method for computing the three-dimensional(3 D)first-order Lagrangian residual velocity(uL)is estab-lished.The method computes tidal body force using the harmonic constants of the zeroth-order tidal current.Compared with using the tidal-averaging method to compute the tidal body force,the proposed method filters out the clutter other than the single-frequency tidal input from the open boundary and obtains uL that is more consistent with the analytic solution.Based on the new method,uL is calculated for a wide bay with a longitudinal topography.The strength and pattern of uL are mostly determined by the parts of the tidal body force related to the vertical mixing of the Stokes’drift and the Coriolis effect,with a minor contribution from the advection effect.The geometrical shape of the bay can influence uL through the topographic gradient.The magnitude of uL increases with the increases in tidal energy input and vertical eddy viscosity and decreases in terms of the bottom friction coefficient.展开更多
In the present paper the concept and properties of the residual functional in Sobolev space are investigated.The weak compactness,force condition,lower semi-continuity and convex of the residual functional are proved....In the present paper the concept and properties of the residual functional in Sobolev space are investigated.The weak compactness,force condition,lower semi-continuity and convex of the residual functional are proved.In Sobolev space,the minimum principle of the residual functional is proposed.The minimum existence theoreomfor J(u)=0 is given by the modern critical point theory.And the equivalence theorem or five equivalence forms for the residual functional equation are also proved.展开更多
In this paper,the equivalent force inside the source which produces a large area deformation field is calculated by using the records of residual deformation,S wave radiation of shear dislocation source and Green func...In this paper,the equivalent force inside the source which produces a large area deformation field is calculated by using the records of residual deformation,S wave radiation of shear dislocation source and Green function of the Lancang-Gengma earthquake.Under the action of equivalent force whose intensity was 1.103×1013 N,the crust derm of northeast segment of seismic fault had finished the upraise and formed permanent irrecoverable deformation within 20.46 min after the major earthquake occurred.The authors indicate that the residual deformation would split into 2 deformation fields with different propagation velocities and different directions in the Song-distance propagation process.展开更多
为研究氧化铟锡(indium tin oxide,ITO)导电玻璃材料的去除机理,采用单磨粒对材料进行切削仿真,建立了ITO导电玻璃的材料模型,根据加工表面形貌、应力和切削力情况分析了材料去除机理,之后研究了切削参数对切削力和残余应力的影响,并与...为研究氧化铟锡(indium tin oxide,ITO)导电玻璃材料的去除机理,采用单磨粒对材料进行切削仿真,建立了ITO导电玻璃的材料模型,根据加工表面形貌、应力和切削力情况分析了材料去除机理,之后研究了切削参数对切削力和残余应力的影响,并与钠钙玻璃进行对比分析。结果表明:在磨粒的切削过程中,材料的去除受ITO薄膜层、玻璃基底和内聚力接触行为的共同影响,会产生分层、通道开裂和层间断裂等失效形式;随着磨粒的进给,切削力在一定范围内波动,且呈现上升、稳定、降低的变化,同时磨粒的切削力与切削速度和切削深度呈正相关;薄膜上残余应力相比玻璃基底,数值更大且波动更剧烈;当切削深度接近ITO薄膜厚度时,薄膜的存在对磨粒切削行为的影响显著。展开更多
基金National Defense Foundation Pre-Research Science Challenge Project(Grant No.JCKY2016212A506-0107)Development Funds of China Academy of Engineering Physics(Grant No.2015B0203029).
文摘Pure iron is one of the difficult-to-machine materials due to its large chip deformation,adhesion,work-hardening,and built-up edges formation during machining.This leads to a large workpiece deformation and challenge to meet the required technical indicators.Therefore,under varying the grain size of pure iron,the influence of cutting speed,feed,and depth of cut on the cutting force,heat generation,and machining residual stresses were explored in the turning process to improve the machinability without compromising the mechanical properties of the material.The experimental findings have depicted that the influence of grain size on cutting force in the precision turning process is not apparent.However,the cutting temperature and residual stress of machining fine-grain iron were much smaller than the coarse grain at all levels of cutting parameters.
基金supported by the Natural Sciences and Engineering Research Council of Canada(NSERC),Grant number:03829Infrastructure was provided by the University of Guelph start-up funding.
文摘Background:Residual torque enhancement(rTE)is the increase in torque observed during the isometric steady state following active muscle lengthening when compared with a fixed-end isometric contraction at the same muscle length and level of neuromuscular activation.In the rTE state,owing to an elevated contribution of passive force to total force production,less active force is required,and there is a subsequent reduction in activation.In vivo studies of rTE reporting an activation reduction are often performed using a dynamometer,where participants contract against a rigid restraint,resisting a torque motor.rTE has yet to be investigated during a position task,which involves the displacement of an inertial load with positional control.Methods:A total of 12 participants(6 males,6 females;age=22.8±1.1 years,height=174.7±8.6 cm,mass=82.1±37.7 kg;mean±SD)completed torque-and position-matching tasks at 60%maximum voluntary contraction for a fixed-end isometric contraction and an isometric contraction following active lengthening of the ankle dorsiflexors.Results:There were no significant differences in activation between torque-and position-matching tasks(p=0.743),with^27%activation reduction following active lengthening for both task types(p<0.001).Conclusion:These results indicate that rTE is a feature of voluntary,position-controlled contractions.These findings support and extend previous findings of isometric torque-control conditions to position-controlled contractions that represent different tasks of daily living.
文摘Corrosion is a primary cause of the slippage of friction⁃type high⁃strength bolted(FHSB)T⁃stub connections.This paper attempts to quantify the residual capacity of FHSB T⁃stub connections with corroded nuts.Firstly,corrosion simulation tests were conducted on 48 manually cut nuts to find out the relationship between the damage degree of nut section and the residual clamping force(RCF)of bolt.Then,static load tests were carried out on 24 FHSB T⁃stub connections with nuts of different degrees of damage to obtain the failure modes.By finite⁃element(FE)models,a comparative analysis was performed on the initial friction load(IFL)and ultimate strength(US)of each connection with corroded nuts.Finally,the parameters of 96 FE models for FHSB T⁃stub connections were analyzed and used to derive the calculation formulas for the degree of damage for each nut and the IFL and US of each connection.The results show that the RCF decay of a bolt is a quadratic function of the equivalent radius loss ratio and the shear failure after nut corrosion;the IFL of each connection had a clear linear correlation with the RCF of the corresponding bolts,and the correlation depends on the applied load and static friction on connecting plate interface induced by the clamping force;the static friction had little impact on the US of the connection;the proposed IFL and US formulas can effectively derive the residual anti⁃slip capacity of FHSB T⁃stub connections from the degree of damage of the corroded nut section.The research results provide a scientific basis for the replacement and maintenance of corroded bolts of FHSB T⁃stub connections.
基金supported by the National Natural Science Foundation of China (No. 41676003)the NSFC Shandong Joint Fund for Marine Science Research Centers (No. U1606402)
文摘An improved method for computing the three-dimensional(3 D)first-order Lagrangian residual velocity(uL)is estab-lished.The method computes tidal body force using the harmonic constants of the zeroth-order tidal current.Compared with using the tidal-averaging method to compute the tidal body force,the proposed method filters out the clutter other than the single-frequency tidal input from the open boundary and obtains uL that is more consistent with the analytic solution.Based on the new method,uL is calculated for a wide bay with a longitudinal topography.The strength and pattern of uL are mostly determined by the parts of the tidal body force related to the vertical mixing of the Stokes’drift and the Coriolis effect,with a minor contribution from the advection effect.The geometrical shape of the bay can influence uL through the topographic gradient.The magnitude of uL increases with the increases in tidal energy input and vertical eddy viscosity and decreases in terms of the bottom friction coefficient.
文摘In the present paper the concept and properties of the residual functional in Sobolev space are investigated.The weak compactness,force condition,lower semi-continuity and convex of the residual functional are proved.In Sobolev space,the minimum principle of the residual functional is proposed.The minimum existence theoreomfor J(u)=0 is given by the modern critical point theory.And the equivalence theorem or five equivalence forms for the residual functional equation are also proved.
文摘In this paper,the equivalent force inside the source which produces a large area deformation field is calculated by using the records of residual deformation,S wave radiation of shear dislocation source and Green function of the Lancang-Gengma earthquake.Under the action of equivalent force whose intensity was 1.103×1013 N,the crust derm of northeast segment of seismic fault had finished the upraise and formed permanent irrecoverable deformation within 20.46 min after the major earthquake occurred.The authors indicate that the residual deformation would split into 2 deformation fields with different propagation velocities and different directions in the Song-distance propagation process.
文摘为研究氧化铟锡(indium tin oxide,ITO)导电玻璃材料的去除机理,采用单磨粒对材料进行切削仿真,建立了ITO导电玻璃的材料模型,根据加工表面形貌、应力和切削力情况分析了材料去除机理,之后研究了切削参数对切削力和残余应力的影响,并与钠钙玻璃进行对比分析。结果表明:在磨粒的切削过程中,材料的去除受ITO薄膜层、玻璃基底和内聚力接触行为的共同影响,会产生分层、通道开裂和层间断裂等失效形式;随着磨粒的进给,切削力在一定范围内波动,且呈现上升、稳定、降低的变化,同时磨粒的切削力与切削速度和切削深度呈正相关;薄膜上残余应力相比玻璃基底,数值更大且波动更剧烈;当切削深度接近ITO薄膜厚度时,薄膜的存在对磨粒切削行为的影响显著。
基金financially supported in part by the National Key Research and Development Pro-gram of China(No.2022YFB3404803)the National Natural Science Foundation of China(No.92160301).
