Membrane separation strategies offer promising platform for the emulsion separation.However,the low mechanical strength of membrane separation layers and the trade-off between separation flux and efficiency present si...Membrane separation strategies offer promising platform for the emulsion separation.However,the low mechanical strength of membrane separation layers and the trade-off between separation flux and efficiency present significant challenges.In this study,we report a CFM@UiO-66-NH_(2)membrane with high separation flux,efficiency and stability,through utilizing a robust anti-abrasion collagen fiber membrane(CFM)as the multifunctional support and UiO-66-NH_(2)by an in-situ growth as the separation layer.The high mechanical strength of the CFM compensated for the weakness of the separation layer,while the charge-breaking effect of UiO-66-NH_(2),along with the size sieving of its constituent separating layers and the capillary effect of the collagen fibers,contributed to the potential for efficient separation.Additionally,the CFM@UiO-66-NH_(2)membrane exhibited superhydrophilic properties,making it suitable for separating oil-in-water microemulsions and nanoemulsions stabilized by anionic surfactants.The membrane demonstrated remarkable separation efficiencies of up to 99.960%and a separation flux of370.05 L·m^(-2)·h^(-1).Moreover,it exhibits stability,durability,and abrasion resistance,maintaining excellent separation performance even when exposed to strong acids and alkalis without any damage to its structure and performance.After six cycles of reuse,it achieved a separation flux of 417.97 L·m^(-2)·h^(-1)and a separation efficiency of 99.747%.Furthermore,after undergoing 500 cycles of strong abrasion,the separation flux remained at 124.39 L·m^(-2)·h^(-1),with a separation efficiency of 99.992%.These properties make it suitable for the long-term use in harsh operating environments.We attribute these properties to the electrostatic effect resulting from the amino group on UiO-66-NH_(2)and its in-situ growth on the CFM,which forms a size-screening separation layer.Our work highlights the potential of the CFM@UiO-66-NH_(2)membrane as an environmentally friendly size-screening material for the efficient emulsion wastewater separation.展开更多
Marine oil spill emulsions are difficult to recover,and the damage to the environment is not easy to eliminate.The use of remote sensing to accurately identify oil spill emulsions is highly important for the protectio...Marine oil spill emulsions are difficult to recover,and the damage to the environment is not easy to eliminate.The use of remote sensing to accurately identify oil spill emulsions is highly important for the protection of marine environments.However,the spectrum of oil emulsions changes due to different water content.Hyperspectral remote sensing and deep learning can use spectral and spatial information to identify different types of oil emulsions.Nonetheless,hyperspectral data can also cause information redundancy,reducing classification accuracy and efficiency,and even overfitting in machine learning models.To address these problems,an oil emulsion deep-learning identification model with spatial-spectral feature fusion is established,and feature bands that can distinguish between crude oil,seawater,water-in-oil emulsion(WO),and oil-in-water emulsion(OW)are filtered based on a standard deviation threshold–mutual information method.Using oil spill airborne hyperspectral data,we conducted identification experiments on oil emulsions in different background waters and under different spatial and temporal conditions,analyzed the transferability of the model,and explored the effects of feature band selection and spectral resolution on the identification of oil emulsions.The results show the following.(1)The standard deviation–mutual information feature selection method is able to effectively extract feature bands that can distinguish between WO,OW,oil slick,and seawater.The number of bands was reduced from 224 to 134 after feature selection on the Airborne Visible Infrared Imaging Spectrometer(AVIRIS)data and from 126 to 100 on the S185 data.(2)With feature selection,the overall accuracy and Kappa of the identification results for the training area are 91.80%and 0.86,respectively,improved by 2.62%and 0.04,and the overall accuracy and Kappa of the identification results for the migration area are 86.53%and 0.80,respectively,improved by 3.45%and 0.05.(3)The oil emulsion identification model has a certain degree of transferability and can effectively identify oil spill emulsions for AVIRIS data at different times and locations,with an overall accuracy of more than 80%,Kappa coefficient of more than 0.7,and F1 score of 0.75 or more for each category.(4)As the spectral resolution decreasing,the model yields different degrees of misclassification for areas with a mixed distribution of oil slick and seawater or mixed distribution of WO and OW.Based on the above experimental results,we demonstrate that the oil emulsion identification model with spatial–spectral feature fusion achieves a high accuracy rate in identifying oil emulsion using airborne hyperspectral data,and can be applied to images under different spatial and temporal conditions.Furthermore,we also elucidate the impact of factors such as spectral resolution and background water bodies on the identification process.These findings provide new reference for future endeavors in automated marine oil spill detection.展开更多
Although hydrophilic membranes are desired for reducing resistance to water permeation, hydrophilic surfaces are not used in the water-in-oil(W/O) membrane emulsification process because water spreads on the hydrophil...Although hydrophilic membranes are desired for reducing resistance to water permeation, hydrophilic surfaces are not used in the water-in-oil(W/O) membrane emulsification process because water spreads on the hydrophilic surface without forming droplets. Here, we report that a hydrophilic ceramic membrane can form a hydrophobic interface in diesel at a higher temperature;interestingly, the experiments show that the contact angle increases when the temperature rises. The hydrophilic membrane surface evolves into a hydrophobic interface, particularly near the boiling point of water, resulting in a water contact angle of 147.5° ± 1.2°. This work established a method for preparing W/O monodispersed emulsions by direct emulsification of hydrophilic ceramic membranes at a temperature close to the boiling point of water.Additionally, it made high flux of membrane emulsification of monodispersed W/O emulsions possible,which satisfied the industrial requirements of fluidized catalytic cracking in the petrochemical industry.展开更多
An improved rheo-optic in situ synchronous measurement system was employed to investigate the gelation behaviour and mechanism of waxy crude oil emulsions. By combining transmitted natural light and reflected polarize...An improved rheo-optic in situ synchronous measurement system was employed to investigate the gelation behaviour and mechanism of waxy crude oil emulsions. By combining transmitted natural light and reflected polarized light microscopy, a multiangle composite light source was built to achieve the simultaneous observation of wax crystals and emulsified water droplets, as well as their dynamic aggregation process. Main outcomes on the microscopic mechanism were obtained by developed microscopic image processing method. It was found that the microstructure of W/O waxy crude oil emulsion has the evolution of “individual structure--homogeneous aggregate structure--heterogeneous coaggregate structure--floc structure” during the static cooling, which results in the four stages during gelation process. Different from previous studies, the aggregation of emulsified water droplets was found to be more significant and contributes to the formation and development of the wax crystals-emulsified water droplets coaggregate, which plays a decisive role in the further evolution of the gelled microstructure. Time series microscopic images show the dynamic aggregation of emulsified water droplets and wax crystals. Two different aggregation behaviours between wax crystals and water droplets were observed. That wax crystals can not only embed in gaps between adjacent water droplets and enhance the structure, but also surround the outside of the water droplets and continue to grow resulting in the interconnection of different coaggregates to form a larger floc structure. In addition, correlation between viscoelasticity and microstructure evolution of waxy crude oil emulsions of different water contents was discussed. With increasing water contents, the microstructure is changed from wax crystal flocculation structure as the main skeleton and the emulsified water droplets embedded in it, into the aggregation of emulsified water droplets occupying the main position. When the number of wax crystals and water droplets reaches a certain ratio, did wax crystals form coaggregates with emulsified water droplets, and the remaining wax crystals formed an overall flocculation structure, the viscoelasticity of the waxy crude oil emulsion is the highest.展开更多
A Pickering emulsion based on sodium starch octenyl succinate(SSOS)was prepared and its effects on the physicochemical properties of hairtail myofibrillar protein gels(MPGs)subjected to multiple freeze-thaw(F-T)cycles...A Pickering emulsion based on sodium starch octenyl succinate(SSOS)was prepared and its effects on the physicochemical properties of hairtail myofibrillar protein gels(MPGs)subjected to multiple freeze-thaw(F-T)cycles were investigated.The whiteness,water-holding capacity,storage modulus(G')and texture properties of the MPGs were significantly improved by adding 1%-2%Pickering emulsion(P<0.05).Meanwhile,Raman spectral analysis demonstrated that Pickering emulsion promoted the transformation of secondary structure,enhanced hydrogen bonds and hydrophobic interactions,and promoted the transition of disulfide bond conformation from g-g-g to g-g-t and t-g-t.At an emulsion concentration of 2%,theα-helix content decreased by 10.37%,while theβ-sheet content increased by 7.94%,compared to the control.After F-T cycles,the structure of the MPGs was destroyed,with an increase in hardness and a decrease in whiteness and water-holding capacity,however,the quality degradation of MPGs was reduced with 1%-2%Pickering emulsion.These findings demonstrated that SSOS-Pickering emulsions,as potential fat substitutes,can enhance the gel properties and the F-T stability of MPGs.展开更多
The influence of different types and concentrations of polymers on the stability of Gudao crude oil emulsion was investigated by measuring the volume of water separated from the emulsions and the interfacial shear vis...The influence of different types and concentrations of polymers on the stability of Gudao crude oil emulsion was investigated by measuring the volume of water separated from the emulsions and the interfacial shear viscosity of the oil/water interfacial film. Experimental results indicate that the simulated water-in-oil emulsion with 40 mg/L of partially hydrolyzed polyacrylamide (HPAM) 3530S could be easily broken by adding demulsifier C and was readily separated into two layers. However, HPAM AX-74H and hydrophobically associating water-soluble polymer (HAP) could stabilize the crude oil emulsion. With increasing concentration of AX-74H and HAP, crude oil emulsions became more stable. Water droplets were loosely packed in the water-in model oil emulsion containing HPAM 3530S, but water droplets were smaller and more closely packed in the emulsion containing AX-74H or HAP. The polymers could be adsorbed on the oil/water interface, thereby increasing the strength of the interracial film and enhancing the emulsion stability.展开更多
The aim of this study was to investigate the effect of high-pressure homogenization on the droplet size and physical stability of different formulations of pectin–zein stabilized rice bran oil emulsions. The obtained...The aim of this study was to investigate the effect of high-pressure homogenization on the droplet size and physical stability of different formulations of pectin–zein stabilized rice bran oil emulsions. The obtained emulsions, both before and after passing through highpressure homogenizer, were subjected to stability test under environmental stress conditions,that is, temperature cycling at 4 °C/40 °C for 6 cycles and centrifugal test at 3000 rpm for 10 min. Applying high-pressure homogenization after mechanical homogenization caused only a small additional decrease in emulsion droplet size. The droplet size of emulsions was influenced by the type of pectin used;emulsions using high methoxy pectin(HMP) were smaller than that using low methoxy pectin(LMP). This is due to a greater emulsifying property of HMP than LMP. The emulsions stabilized by HMP–zein showed good physical stability with lower percent creaming index than those using LMP, both before and after passing through high-pressure homogenizer. The stability of emulsions after passing through high-pressure homogenizer was slightly higher when using higher zein concentration, resulting from stronger pectin–zein complexes that could rearrange and adsorb onto the emulsion droplets.展开更多
In recent years,Pickering emulsions and their applications have attracted a great deal of attention due to their special features,which include easy preparation and enhanced stability.In contrast to classical emulsion...In recent years,Pickering emulsions and their applications have attracted a great deal of attention due to their special features,which include easy preparation and enhanced stability.In contrast to classical emulsions,in Pickering emulsions,solid microparticles or nanoparticles that localize at the interface between liquids are used as stabilizers,instead of surfactants,to enhance the droplet lifetime.Furthermore,Pickering emulsions show higher stability,lower toxicity,and stimuli-responsiveness,compared with emulsions that are stabilized by surfactants.Therefore,they can be considered attractive components for various uses,such as photocatalysis and the preparation of new materials.Moreover,the nanoparticle morphology strongly influences Pickering emulsion stability as well as the potential utilization of such emulsions.Here,we review recent findings concerning Pickering emulsions,with a particular focus on how the nanoparticles morphology(i.e.,cube,ellipsoid,nanosheet,sphere,cylinder,rod,peanut)influences the type and stability of such emulsions,and their current applications in different fields such as antibacterial activity,protein recognition,catalysis,photocatalysis,and water purification.展开更多
This study aims to develop a paraffin-based phase change material(PCM) emulsion with a low extent of supercooling for thermal energy storage(TES) systems to improve the cooling efficiency.Hexadecane-water emulsions we...This study aims to develop a paraffin-based phase change material(PCM) emulsion with a low extent of supercooling for thermal energy storage(TES) systems to improve the cooling efficiency.Hexadecane-water emulsions were prepared and characterized. Multi-wall carbon nanotubes(MWCNTs) were dispersed in the emulsion as a nucleating agent to reduce the supercooling. The MWCNTs were chemically modified with carboxyl groups to improve the dispersion of the tubular particles in the organic liquid. Thermal analyses of the emulsions by differential scanning calorimeter(DSC) indicated that the extent of supercooling was significantly reduced. The concentration of the nucleating agent for an effective supercooling suppression as found to be very low, in agreement with previous findings, and there appeared to be a minimum concentration for the supercooling reduction.展开更多
Macromolecules of polysaccharides, proteins and poloxamers have a hydrophobic portion and a hydrophilic one that can be used as emulsifiers. Parts of these emulsifiers are safe pharmaceutical excipients, which can rep...Macromolecules of polysaccharides, proteins and poloxamers have a hydrophobic portion and a hydrophilic one that can be used as emulsifiers. Parts of these emulsifiers are safe pharmaceutical excipients, which can replace the irritant low molecular weight surfactants to formulate emulsions for the pharmaceutical field. This project focused on preparing O/W emulsions stabilized with polymers for pharmaceuticals such as polysaccharides, proteins and poloxamers, including hydroxypropyl methylcellulose (HPMC), methylcellulose (MC),gelatin, poloxamer 407 (F127) and poloxamer 188 (F68). Emulsion physical stability was assessed by centrifugation, autoclaving sterilization and droplet size measurements. The stabilization mechanisms of emulsions were determined by interfacial tension and rheological measurements. Results stated that the efficacy of these polymers for pharmaceuticals stabilized emulsions was sorted in the order: F127 > F68 > HPMC > MC > Gelatin.展开更多
Formation and flow of emulsions in porous media are common in all enhanced oil recovery tech- niques. In most cases, oil-in-water (O/W) emulsions are formed in porous media due to oil-water interaction. Even now, de...Formation and flow of emulsions in porous media are common in all enhanced oil recovery tech- niques. In most cases, oil-in-water (O/W) emulsions are formed in porous media due to oil-water interaction. Even now, detailed flow mechanisms of emulsions through porous media are not well understood. In this study, variation of rate of flow of O/W emulsions with pressure drop was studied experimentally, and rheological pa- rameters were calculated. The pressure drop increases with an increase in oil concentration in the O/W emulsion due to high viscosity. The effective viscosity of the emulsion was calculated from the derived model and expressed as a function of shear rate while flowing through porous media. Flow of O/W emulsions of different concentrations was evaluated in sand packs of different sand sizes. Emulsions were characterized by analyzing their stability, rheological properties, and tem- perature effects on rheological properties.展开更多
Various Cu/ZnO/Al2O3 catalysts have been synthesized by different aluminum emulsions as aluminum sources and their pertormances tor methanol synthesis from syngas have been investigated. The influences of preparation ...Various Cu/ZnO/Al2O3 catalysts have been synthesized by different aluminum emulsions as aluminum sources and their pertormances tor methanol synthesis from syngas have been investigated. The influences of preparation methods of aluminum emulsions on physicochemical and catalytic properties of catalysts were studied by XRD, SEM, XPS,N2 adsorption-desorption techniques and methanol synthesis from syngas. The preparation methods of aluminum emulsions were found to influence the catalytic activity, CuO crystallite size, surface area and Cu0 surface area and reduction process. The results show that the catalyst CN using the aluminum source prepared by addition the ammonia into the aluminum nitrate (NP) exhibited the best catalytic performance for methanol synthesis from syngas.展开更多
A series of polyacrylate emulsions were blended with tackifier resin emulsions such as modified rosin emulsion, C5 resin and C9 resin emulsion. The miscibility of the polyacrylates and tackifier resins was investigate...A series of polyacrylate emulsions were blended with tackifier resin emulsions such as modified rosin emulsion, C5 resin and C9 resin emulsion. The miscibility of the polyacrylates and tackifier resins was investigated by means of SEM and visual observation. The phase diagrams of the miscibility change systematically with the polarity of polyacrylates and tackifier resins. The influence of the content of the tackifier resins on the adhesion properties of the; polyacrylate emulsions were also studied. The results show that the 180 degrees C peel strength is improved as the amount of the tackifier resin increases and comes to a maximum at a specific content. The ball tack property decreases slightly and the hold strength changes complicatedly as the tackifier resin increases.展开更多
Pharmaceutical delivery systems are developed to improve the physicochemical properties of therapeutic compounds. Emulsions are one of these drug delivering systems formulated using water, oils and lipids as main ingr...Pharmaceutical delivery systems are developed to improve the physicochemical properties of therapeutic compounds. Emulsions are one of these drug delivering systems formulated using water, oils and lipids as main ingredients. Extensive data are usually generated on the physical and chemical characteristics of these oil-in-water and lipid emulsions. However, the oxidative tendency of emulsions is often overlooked. Oxidation impacts the overall quality and safety of these pharmaceutical emulsions. Additionally, introducing oxidatively unstable emulsions into biological systems further promotes oxidation in situ. Products of these reactions then continue to pose serious harm to cells and fuel other physiological oxidation reactions. Consequently, the increase of oxidation products leads to oxidative damage to biological systems. Thus, emulsions with lower lipid peroxidation are more stable and will reduce the negative effects of oxidation in situ. Preventive measures during the formulation of emulsions are important. Many naturally occurring and cost effective substances possess low oxidation tendencies and confer oxidative protection when used in emulsions. Additionally,certain preparatory methods should be employed to reduce or better control lipid peroxidation.Finally, emulsions must be evaluated for their oxidation susceptibility using the various techniques available. Careful attention to the preparation of emulsions and assessment of their oxidative stability will help produce safer emulsions without compromising efficacy.展开更多
A series of π-A isotherms are drawn to study the film properties of the components with Langmuir-Blodgett technique. The effects of the aromaticity of spread solvents and pH value on the air/water film formed by the...A series of π-A isotherms are drawn to study the film properties of the components with Langmuir-Blodgett technique. The effects of the aromaticity of spread solvents and pH value on the air/water film formed by the components are investigated. Acid fraction and asphaltene can form stable two-dimensional insoluble films on an air/water surface. The surface film pressure of acid fraction and asphaltene is higher and more stable than that of the other fractions. The surface film pressure of the fraction increases evidently under the basic condition (pH=12). The results show that the interfacial activity of acid fraction and asphaltene is superior to that of the other fractions and the basic condition is favorable to the stability of the O/W emulsion.展开更多
The efficient separation of water-in-oil emulsion is of significance in environment and energy filed,and it has become a world-wide challenge.Herein,we have presented a one-step,facile and low-cost approach to prepare...The efficient separation of water-in-oil emulsion is of significance in environment and energy filed,and it has become a world-wide challenge.Herein,we have presented a one-step,facile and low-cost approach to prepare superhydrophobic sands for efficient separation of water-in-oil emulsion.The as-prepared sand layers possessed a water contact angle higher than 151°,demonstrating their superior superhydrophobic property.Besides,the as-prepared sand layers could separate water-in-emulsions with separation efficiency up to 99.7%,which is superior to both traditional and superwettable filtration membranes.The effect of thickness of sand layer on separation performance was also investigated.The results showed that the filtration flux decreased with the increased of filtration thickness while the separation efficiency increased.The as-prepared sand layer proposed by this study is a processing candidate for separating water-in-oil emulsion in practical industry.Additionally,the as-prepared superhydrophobic sand fabrication method also provides an alternative for desert water storage.展开更多
The synthesis and characterization of a new class of cementitious composites filled with polymer emulsions were investigated, and their superior mechanical strength and durability properties compared to composites dev...The synthesis and characterization of a new class of cementitious composites filled with polymer emulsions were investigated, and their superior mechanical strength and durability properties compared to composites devoid of fi llers were reported. Polymer emulsions were utilized to mechanically reinforce the composite and bridge the cement, fly ash, aggregate and fibers. The results reveal that the epoxy emulsion and poly(ethylene-co-vinyl acetate) emulsion markedly enhance the mechanical and durability properties of cemetitious composites. The fi bers can be pulled out in the form of slip-hardening and the abrasion phenomenon can be observed clearly on the surface of the fibers. The hydration extent of cement is higher than that of the pristine composites. The polymer modified cementitious composites designed on micromechanics, have fl exibility and plasticity which could be applied for a novel form of multifunctional materials with a range of pipeline coatings applications.展开更多
Responsive emulsions are the emulsions that can be reversibly switched on-demand between“stable”and“unstable”by environmental stimulus or trigger,which allows a simple and effective adjustment approach to achieve ...Responsive emulsions are the emulsions that can be reversibly switched on-demand between“stable”and“unstable”by environmental stimulus or trigger,which allows a simple and effective adjustment approach to achieve emulsification and demulsification.In recent years,stimuli-responsive emulsions acting as smart soft material are received considerable attention with the advantages of simple manipulation,good reversibility,low cost,easy treatment,and little effect on the system.In this paper,the recent research progress of emulsions that can respond to external stimuli,including pH,light,magnetic field,CO_(2)/N_(2) and dual responsive are reviewed.Also,the potential applications based on responsive emulsion are discussed,such as catalytic reactions,heavy oil recovery,polymer particles synthesis and optical sensor,aiming to summarize the latest achievements and put forward the possible development trends of responsive emulsions.展开更多
High Performance Liquid Chromatography (HPLC) experiments have been performed on nine steviol glycosides namely rebaudioside A, steviolbioside, stevioside, rubusoside, rebaudioside B, rebaudioside C, rebaudioside D, r...High Performance Liquid Chromatography (HPLC) experiments have been performed on nine steviol glycosides namely rebaudioside A, steviolbioside, stevioside, rubusoside, rebaudioside B, rebaudioside C, rebaudioside D, rebaudioside F, and dulcoside A isolated from the leaves of Stevia rebaudiana using Reversed-Phase (RP) column. Using RP-HPLC method, the individual retention times for nine naturally occurring ent-kaurane diterpene glycosides of S. rebaudiana reported in JECFA have been determined at four different temperatures: 20℃, 40℃, 60℃, and 79℃. Also, calculated the relative retention times of the eight steviol glycosides steviolbioside, stevioside, rubusoside, rebaudioside B, rebaudioside C, rebaudioside D, rebaudioside F, and dulcoside A against the major steviol glycoside rebaudioside A. HPLC results suggested that temperatures 40℃ and 60℃ would be ideal conditions for better separation of steviol glycosides.展开更多
A novel and high-efficiency coalescence membrane enhanced by nano-sized polyvinylidene fluoride(PVDF)nanofibers based on polyester(PET)substrate was fabricated using electrospinning method.The properties of the electr...A novel and high-efficiency coalescence membrane enhanced by nano-sized polyvinylidene fluoride(PVDF)nanofibers based on polyester(PET)substrate was fabricated using electrospinning method.The properties of the electrospun nanofibers such as roughness and surface morphology greatly affected the oil droplet interception efficiency and surface wettability of the membrane.A series of coalescence units were prepared with different layers of nanofibrous membrane and the separation efficiencies at different initial concentrations,flow rates,and oil types were tested.It is very interesting that the obtained nanofibrous membrane exhibited superoleophilicity in air but poor oleophilicity under water,which was beneficial to the coalescence process.The coalescence unit with four membrane layers had excellent performances under different initial concentrations and flow rates.The separation efficiency of the 4-layers unit remained above 98.2%when the initial concentration reached up to 2000 mg·L-1.Furthermore,the unit also exhibited good performance with the increasing oil density and viscosity,which is promising for large-scale oil wastewater treatment.展开更多
基金supported by National Natural Science Foundation of China(22008035,22108040,22378066)Science and Technology Project of Environmental Protection in Fujian(2022R026)Natural Science Foundation of Fujian Province(2020J05131,2020J05130)。
文摘Membrane separation strategies offer promising platform for the emulsion separation.However,the low mechanical strength of membrane separation layers and the trade-off between separation flux and efficiency present significant challenges.In this study,we report a CFM@UiO-66-NH_(2)membrane with high separation flux,efficiency and stability,through utilizing a robust anti-abrasion collagen fiber membrane(CFM)as the multifunctional support and UiO-66-NH_(2)by an in-situ growth as the separation layer.The high mechanical strength of the CFM compensated for the weakness of the separation layer,while the charge-breaking effect of UiO-66-NH_(2),along with the size sieving of its constituent separating layers and the capillary effect of the collagen fibers,contributed to the potential for efficient separation.Additionally,the CFM@UiO-66-NH_(2)membrane exhibited superhydrophilic properties,making it suitable for separating oil-in-water microemulsions and nanoemulsions stabilized by anionic surfactants.The membrane demonstrated remarkable separation efficiencies of up to 99.960%and a separation flux of370.05 L·m^(-2)·h^(-1).Moreover,it exhibits stability,durability,and abrasion resistance,maintaining excellent separation performance even when exposed to strong acids and alkalis without any damage to its structure and performance.After six cycles of reuse,it achieved a separation flux of 417.97 L·m^(-2)·h^(-1)and a separation efficiency of 99.747%.Furthermore,after undergoing 500 cycles of strong abrasion,the separation flux remained at 124.39 L·m^(-2)·h^(-1),with a separation efficiency of 99.992%.These properties make it suitable for the long-term use in harsh operating environments.We attribute these properties to the electrostatic effect resulting from the amino group on UiO-66-NH_(2)and its in-situ growth on the CFM,which forms a size-screening separation layer.Our work highlights the potential of the CFM@UiO-66-NH_(2)membrane as an environmentally friendly size-screening material for the efficient emulsion wastewater separation.
基金The National Natural Science Foundation of China under contract Nos 61890964 and 42206177the Joint Funds of the National Natural Science Foundation of China under contract No.U1906217.
文摘Marine oil spill emulsions are difficult to recover,and the damage to the environment is not easy to eliminate.The use of remote sensing to accurately identify oil spill emulsions is highly important for the protection of marine environments.However,the spectrum of oil emulsions changes due to different water content.Hyperspectral remote sensing and deep learning can use spectral and spatial information to identify different types of oil emulsions.Nonetheless,hyperspectral data can also cause information redundancy,reducing classification accuracy and efficiency,and even overfitting in machine learning models.To address these problems,an oil emulsion deep-learning identification model with spatial-spectral feature fusion is established,and feature bands that can distinguish between crude oil,seawater,water-in-oil emulsion(WO),and oil-in-water emulsion(OW)are filtered based on a standard deviation threshold–mutual information method.Using oil spill airborne hyperspectral data,we conducted identification experiments on oil emulsions in different background waters and under different spatial and temporal conditions,analyzed the transferability of the model,and explored the effects of feature band selection and spectral resolution on the identification of oil emulsions.The results show the following.(1)The standard deviation–mutual information feature selection method is able to effectively extract feature bands that can distinguish between WO,OW,oil slick,and seawater.The number of bands was reduced from 224 to 134 after feature selection on the Airborne Visible Infrared Imaging Spectrometer(AVIRIS)data and from 126 to 100 on the S185 data.(2)With feature selection,the overall accuracy and Kappa of the identification results for the training area are 91.80%and 0.86,respectively,improved by 2.62%and 0.04,and the overall accuracy and Kappa of the identification results for the migration area are 86.53%and 0.80,respectively,improved by 3.45%and 0.05.(3)The oil emulsion identification model has a certain degree of transferability and can effectively identify oil spill emulsions for AVIRIS data at different times and locations,with an overall accuracy of more than 80%,Kappa coefficient of more than 0.7,and F1 score of 0.75 or more for each category.(4)As the spectral resolution decreasing,the model yields different degrees of misclassification for areas with a mixed distribution of oil slick and seawater or mixed distribution of WO and OW.Based on the above experimental results,we demonstrate that the oil emulsion identification model with spatial–spectral feature fusion achieves a high accuracy rate in identifying oil emulsion using airborne hyperspectral data,and can be applied to images under different spatial and temporal conditions.Furthermore,we also elucidate the impact of factors such as spectral resolution and background water bodies on the identification process.These findings provide new reference for future endeavors in automated marine oil spill detection.
基金the support from the National Key Research and Development Program of China (2021YFB3801303)the National Natural Science Foundation of China (21838005, 21921006)the Key Scientific Research and Development Projects of Jiangsu Province (BE201800901)。
文摘Although hydrophilic membranes are desired for reducing resistance to water permeation, hydrophilic surfaces are not used in the water-in-oil(W/O) membrane emulsification process because water spreads on the hydrophilic surface without forming droplets. Here, we report that a hydrophilic ceramic membrane can form a hydrophobic interface in diesel at a higher temperature;interestingly, the experiments show that the contact angle increases when the temperature rises. The hydrophilic membrane surface evolves into a hydrophobic interface, particularly near the boiling point of water, resulting in a water contact angle of 147.5° ± 1.2°. This work established a method for preparing W/O monodispersed emulsions by direct emulsification of hydrophilic ceramic membranes at a temperature close to the boiling point of water.Additionally, it made high flux of membrane emulsification of monodispersed W/O emulsions possible,which satisfied the industrial requirements of fluidized catalytic cracking in the petrochemical industry.
文摘An improved rheo-optic in situ synchronous measurement system was employed to investigate the gelation behaviour and mechanism of waxy crude oil emulsions. By combining transmitted natural light and reflected polarized light microscopy, a multiangle composite light source was built to achieve the simultaneous observation of wax crystals and emulsified water droplets, as well as their dynamic aggregation process. Main outcomes on the microscopic mechanism were obtained by developed microscopic image processing method. It was found that the microstructure of W/O waxy crude oil emulsion has the evolution of “individual structure--homogeneous aggregate structure--heterogeneous coaggregate structure--floc structure” during the static cooling, which results in the four stages during gelation process. Different from previous studies, the aggregation of emulsified water droplets was found to be more significant and contributes to the formation and development of the wax crystals-emulsified water droplets coaggregate, which plays a decisive role in the further evolution of the gelled microstructure. Time series microscopic images show the dynamic aggregation of emulsified water droplets and wax crystals. Two different aggregation behaviours between wax crystals and water droplets were observed. That wax crystals can not only embed in gaps between adjacent water droplets and enhance the structure, but also surround the outside of the water droplets and continue to grow resulting in the interconnection of different coaggregates to form a larger floc structure. In addition, correlation between viscoelasticity and microstructure evolution of waxy crude oil emulsions of different water contents was discussed. With increasing water contents, the microstructure is changed from wax crystal flocculation structure as the main skeleton and the emulsified water droplets embedded in it, into the aggregation of emulsified water droplets occupying the main position. When the number of wax crystals and water droplets reaches a certain ratio, did wax crystals form coaggregates with emulsified water droplets, and the remaining wax crystals formed an overall flocculation structure, the viscoelasticity of the waxy crude oil emulsion is the highest.
基金supported by the National Natural Science Foundation of China(U20A2067,32272360)。
文摘A Pickering emulsion based on sodium starch octenyl succinate(SSOS)was prepared and its effects on the physicochemical properties of hairtail myofibrillar protein gels(MPGs)subjected to multiple freeze-thaw(F-T)cycles were investigated.The whiteness,water-holding capacity,storage modulus(G')and texture properties of the MPGs were significantly improved by adding 1%-2%Pickering emulsion(P<0.05).Meanwhile,Raman spectral analysis demonstrated that Pickering emulsion promoted the transformation of secondary structure,enhanced hydrogen bonds and hydrophobic interactions,and promoted the transition of disulfide bond conformation from g-g-g to g-g-t and t-g-t.At an emulsion concentration of 2%,theα-helix content decreased by 10.37%,while theβ-sheet content increased by 7.94%,compared to the control.After F-T cycles,the structure of the MPGs was destroyed,with an increase in hardness and a decrease in whiteness and water-holding capacity,however,the quality degradation of MPGs was reduced with 1%-2%Pickering emulsion.These findings demonstrated that SSOS-Pickering emulsions,as potential fat substitutes,can enhance the gel properties and the F-T stability of MPGs.
文摘The influence of different types and concentrations of polymers on the stability of Gudao crude oil emulsion was investigated by measuring the volume of water separated from the emulsions and the interfacial shear viscosity of the oil/water interfacial film. Experimental results indicate that the simulated water-in-oil emulsion with 40 mg/L of partially hydrolyzed polyacrylamide (HPAM) 3530S could be easily broken by adding demulsifier C and was readily separated into two layers. However, HPAM AX-74H and hydrophobically associating water-soluble polymer (HAP) could stabilize the crude oil emulsion. With increasing concentration of AX-74H and HAP, crude oil emulsions became more stable. Water droplets were loosely packed in the water-in model oil emulsion containing HPAM 3530S, but water droplets were smaller and more closely packed in the emulsion containing AX-74H or HAP. The polymers could be adsorbed on the oil/water interface, thereby increasing the strength of the interracial film and enhancing the emulsion stability.
基金financially supported by the Research and Development Institute, Silpakorn University
文摘The aim of this study was to investigate the effect of high-pressure homogenization on the droplet size and physical stability of different formulations of pectin–zein stabilized rice bran oil emulsions. The obtained emulsions, both before and after passing through highpressure homogenizer, were subjected to stability test under environmental stress conditions,that is, temperature cycling at 4 °C/40 °C for 6 cycles and centrifugal test at 3000 rpm for 10 min. Applying high-pressure homogenization after mechanical homogenization caused only a small additional decrease in emulsion droplet size. The droplet size of emulsions was influenced by the type of pectin used;emulsions using high methoxy pectin(HMP) were smaller than that using low methoxy pectin(LMP). This is due to a greater emulsifying property of HMP than LMP. The emulsions stabilized by HMP–zein showed good physical stability with lower percent creaming index than those using LMP, both before and after passing through high-pressure homogenizer. The stability of emulsions after passing through high-pressure homogenizer was slightly higher when using higher zein concentration, resulting from stronger pectin–zein complexes that could rearrange and adsorb onto the emulsion droplets.
文摘In recent years,Pickering emulsions and their applications have attracted a great deal of attention due to their special features,which include easy preparation and enhanced stability.In contrast to classical emulsions,in Pickering emulsions,solid microparticles or nanoparticles that localize at the interface between liquids are used as stabilizers,instead of surfactants,to enhance the droplet lifetime.Furthermore,Pickering emulsions show higher stability,lower toxicity,and stimuli-responsiveness,compared with emulsions that are stabilized by surfactants.Therefore,they can be considered attractive components for various uses,such as photocatalysis and the preparation of new materials.Moreover,the nanoparticle morphology strongly influences Pickering emulsion stability as well as the potential utilization of such emulsions.Here,we review recent findings concerning Pickering emulsions,with a particular focus on how the nanoparticles morphology(i.e.,cube,ellipsoid,nanosheet,sphere,cylinder,rod,peanut)influences the type and stability of such emulsions,and their current applications in different fields such as antibacterial activity,protein recognition,catalysis,photocatalysis,and water purification.
基金Supported by the Research Grant Council of the Hong Kong SAR government(GRF PolyU 5241/11E)
文摘This study aims to develop a paraffin-based phase change material(PCM) emulsion with a low extent of supercooling for thermal energy storage(TES) systems to improve the cooling efficiency.Hexadecane-water emulsions were prepared and characterized. Multi-wall carbon nanotubes(MWCNTs) were dispersed in the emulsion as a nucleating agent to reduce the supercooling. The MWCNTs were chemically modified with carboxyl groups to improve the dispersion of the tubular particles in the organic liquid. Thermal analyses of the emulsions by differential scanning calorimeter(DSC) indicated that the extent of supercooling was significantly reduced. The concentration of the nucleating agent for an effective supercooling suppression as found to be very low, in agreement with previous findings, and there appeared to be a minimum concentration for the supercooling reduction.
基金supported by the National Natural Science Foundation of China (No.81273445 and No.81473161)
文摘Macromolecules of polysaccharides, proteins and poloxamers have a hydrophobic portion and a hydrophilic one that can be used as emulsifiers. Parts of these emulsifiers are safe pharmaceutical excipients, which can replace the irritant low molecular weight surfactants to formulate emulsions for the pharmaceutical field. This project focused on preparing O/W emulsions stabilized with polymers for pharmaceuticals such as polysaccharides, proteins and poloxamers, including hydroxypropyl methylcellulose (HPMC), methylcellulose (MC),gelatin, poloxamer 407 (F127) and poloxamer 188 (F68). Emulsion physical stability was assessed by centrifugation, autoclaving sterilization and droplet size measurements. The stabilization mechanisms of emulsions were determined by interfacial tension and rheological measurements. Results stated that the efficacy of these polymers for pharmaceuticals stabilized emulsions was sorted in the order: F127 > F68 > HPMC > MC > Gelatin.
文摘Formation and flow of emulsions in porous media are common in all enhanced oil recovery tech- niques. In most cases, oil-in-water (O/W) emulsions are formed in porous media due to oil-water interaction. Even now, detailed flow mechanisms of emulsions through porous media are not well understood. In this study, variation of rate of flow of O/W emulsions with pressure drop was studied experimentally, and rheological pa- rameters were calculated. The pressure drop increases with an increase in oil concentration in the O/W emulsion due to high viscosity. The effective viscosity of the emulsion was calculated from the derived model and expressed as a function of shear rate while flowing through porous media. Flow of O/W emulsions of different concentrations was evaluated in sand packs of different sand sizes. Emulsions were characterized by analyzing their stability, rheological properties, and tem- perature effects on rheological properties.
文摘Various Cu/ZnO/Al2O3 catalysts have been synthesized by different aluminum emulsions as aluminum sources and their pertormances tor methanol synthesis from syngas have been investigated. The influences of preparation methods of aluminum emulsions on physicochemical and catalytic properties of catalysts were studied by XRD, SEM, XPS,N2 adsorption-desorption techniques and methanol synthesis from syngas. The preparation methods of aluminum emulsions were found to influence the catalytic activity, CuO crystallite size, surface area and Cu0 surface area and reduction process. The results show that the catalyst CN using the aluminum source prepared by addition the ammonia into the aluminum nitrate (NP) exhibited the best catalytic performance for methanol synthesis from syngas.
文摘A series of polyacrylate emulsions were blended with tackifier resin emulsions such as modified rosin emulsion, C5 resin and C9 resin emulsion. The miscibility of the polyacrylates and tackifier resins was investigated by means of SEM and visual observation. The phase diagrams of the miscibility change systematically with the polarity of polyacrylates and tackifier resins. The influence of the content of the tackifier resins on the adhesion properties of the; polyacrylate emulsions were also studied. The results show that the 180 degrees C peel strength is improved as the amount of the tackifier resin increases and comes to a maximum at a specific content. The ball tack property decreases slightly and the hold strength changes complicatedly as the tackifier resin increases.
文摘Pharmaceutical delivery systems are developed to improve the physicochemical properties of therapeutic compounds. Emulsions are one of these drug delivering systems formulated using water, oils and lipids as main ingredients. Extensive data are usually generated on the physical and chemical characteristics of these oil-in-water and lipid emulsions. However, the oxidative tendency of emulsions is often overlooked. Oxidation impacts the overall quality and safety of these pharmaceutical emulsions. Additionally, introducing oxidatively unstable emulsions into biological systems further promotes oxidation in situ. Products of these reactions then continue to pose serious harm to cells and fuel other physiological oxidation reactions. Consequently, the increase of oxidation products leads to oxidative damage to biological systems. Thus, emulsions with lower lipid peroxidation are more stable and will reduce the negative effects of oxidation in situ. Preventive measures during the formulation of emulsions are important. Many naturally occurring and cost effective substances possess low oxidation tendencies and confer oxidative protection when used in emulsions. Additionally,certain preparatory methods should be employed to reduce or better control lipid peroxidation.Finally, emulsions must be evaluated for their oxidation susceptibility using the various techniques available. Careful attention to the preparation of emulsions and assessment of their oxidative stability will help produce safer emulsions without compromising efficacy.
文摘A series of π-A isotherms are drawn to study the film properties of the components with Langmuir-Blodgett technique. The effects of the aromaticity of spread solvents and pH value on the air/water film formed by the components are investigated. Acid fraction and asphaltene can form stable two-dimensional insoluble films on an air/water surface. The surface film pressure of acid fraction and asphaltene is higher and more stable than that of the other fractions. The surface film pressure of the fraction increases evidently under the basic condition (pH=12). The results show that the interfacial activity of acid fraction and asphaltene is superior to that of the other fractions and the basic condition is favorable to the stability of the O/W emulsion.
基金supported by the Northeast Petroleum University Youth Science Foundation of China (Grant No. 15071120619)Tribology Science Fund of State Key Laboratory of Tribology (No. SKLTKF19B05)
文摘The efficient separation of water-in-oil emulsion is of significance in environment and energy filed,and it has become a world-wide challenge.Herein,we have presented a one-step,facile and low-cost approach to prepare superhydrophobic sands for efficient separation of water-in-oil emulsion.The as-prepared sand layers possessed a water contact angle higher than 151°,demonstrating their superior superhydrophobic property.Besides,the as-prepared sand layers could separate water-in-emulsions with separation efficiency up to 99.7%,which is superior to both traditional and superwettable filtration membranes.The effect of thickness of sand layer on separation performance was also investigated.The results showed that the filtration flux decreased with the increased of filtration thickness while the separation efficiency increased.The as-prepared sand layer proposed by this study is a processing candidate for separating water-in-oil emulsion in practical industry.Additionally,the as-prepared superhydrophobic sand fabrication method also provides an alternative for desert water storage.
基金Funded by the National Natural Science Foundation of China(No.21076227)
文摘The synthesis and characterization of a new class of cementitious composites filled with polymer emulsions were investigated, and their superior mechanical strength and durability properties compared to composites devoid of fi llers were reported. Polymer emulsions were utilized to mechanically reinforce the composite and bridge the cement, fly ash, aggregate and fibers. The results reveal that the epoxy emulsion and poly(ethylene-co-vinyl acetate) emulsion markedly enhance the mechanical and durability properties of cemetitious composites. The fi bers can be pulled out in the form of slip-hardening and the abrasion phenomenon can be observed clearly on the surface of the fibers. The hydration extent of cement is higher than that of the pristine composites. The polymer modified cementitious composites designed on micromechanics, have fl exibility and plasticity which could be applied for a novel form of multifunctional materials with a range of pipeline coatings applications.
基金supported by the National Natural Science Foun-dation of China(21908026)the Fujian Province science and tech-nology guidance project(2021Y0007)Key Program of Qingyuan Innovation Laboratory(00221004).
文摘Responsive emulsions are the emulsions that can be reversibly switched on-demand between“stable”and“unstable”by environmental stimulus or trigger,which allows a simple and effective adjustment approach to achieve emulsification and demulsification.In recent years,stimuli-responsive emulsions acting as smart soft material are received considerable attention with the advantages of simple manipulation,good reversibility,low cost,easy treatment,and little effect on the system.In this paper,the recent research progress of emulsions that can respond to external stimuli,including pH,light,magnetic field,CO_(2)/N_(2) and dual responsive are reviewed.Also,the potential applications based on responsive emulsion are discussed,such as catalytic reactions,heavy oil recovery,polymer particles synthesis and optical sensor,aiming to summarize the latest achievements and put forward the possible development trends of responsive emulsions.
文摘High Performance Liquid Chromatography (HPLC) experiments have been performed on nine steviol glycosides namely rebaudioside A, steviolbioside, stevioside, rubusoside, rebaudioside B, rebaudioside C, rebaudioside D, rebaudioside F, and dulcoside A isolated from the leaves of Stevia rebaudiana using Reversed-Phase (RP) column. Using RP-HPLC method, the individual retention times for nine naturally occurring ent-kaurane diterpene glycosides of S. rebaudiana reported in JECFA have been determined at four different temperatures: 20℃, 40℃, 60℃, and 79℃. Also, calculated the relative retention times of the eight steviol glycosides steviolbioside, stevioside, rubusoside, rebaudioside B, rebaudioside C, rebaudioside D, rebaudioside F, and dulcoside A against the major steviol glycoside rebaudioside A. HPLC results suggested that temperatures 40℃ and 60℃ would be ideal conditions for better separation of steviol glycosides.
基金supported by the National Key Research and Development Program of China(No.2017YFB0308000)the National Natural Science Foundation of China(No.21706259)+3 种基金the State Key Laboratory of Heavy Oil Processing(SKLOP201903001)Guizhou Science Technology Support Program([2019]2839)the Natural Science Youth Foundation of Shanxi Province(No.201701D221033)Program of Innovation Academy for Green Manufacture,CAS(IAGM2020C04)。
文摘A novel and high-efficiency coalescence membrane enhanced by nano-sized polyvinylidene fluoride(PVDF)nanofibers based on polyester(PET)substrate was fabricated using electrospinning method.The properties of the electrospun nanofibers such as roughness and surface morphology greatly affected the oil droplet interception efficiency and surface wettability of the membrane.A series of coalescence units were prepared with different layers of nanofibrous membrane and the separation efficiencies at different initial concentrations,flow rates,and oil types were tested.It is very interesting that the obtained nanofibrous membrane exhibited superoleophilicity in air but poor oleophilicity under water,which was beneficial to the coalescence process.The coalescence unit with four membrane layers had excellent performances under different initial concentrations and flow rates.The separation efficiency of the 4-layers unit remained above 98.2%when the initial concentration reached up to 2000 mg·L-1.Furthermore,the unit also exhibited good performance with the increasing oil density and viscosity,which is promising for large-scale oil wastewater treatment.