Thermal behavior of the HTR-10 under combined PLOFC and ATWS condition initiated by unscrammed control rod withdrawal

Two tests initiated by unscrammed control rod withdrawal were performed on the High Temperature GasCooled Reactor-Test Module(HTR-10) in November 2003 after the reactor achieved its full power, and the test conditions represented a typical transient scenario of modular high-temperature reactors(HTRs), called pressurized loss of forced cooling, and anticipated transient without scram.Based on the test parameters, the HTR-10 thermal behaviors under the test conditions were studied with the help of the system analysis code THERMIX. The combination of the test results and the investigation results makes the HTR-10 safety potential better understood. Key phenomena, such as the helium natural circulation and the temperature redistribution in the reactor, were revealed. As the safety feature of most significance, there is a large margin between the maximum fuel temperature and its safety limit in each test. Temperatures of thermocouples in different components were calculated by THERMIX and compared with the test values. The applicability of the code was verified by good agreement obtained from the comparison.

Study of Control rod worth in the TMSR

Control rod is a primary control part of emergency control and power regulation in nuclear reactor. The main application of it is to control fast change of the reactivity. The theoretical analysis for the worth of control rod is necessary in the stage of design. Based on design requirements, some results are calculated. Firstly, control rod worth with different density of neutron absorber is calculated by MCNP here. Secondly, the study of integral and differential control rod worth is presented in this paper while the control rod is inserted into reactor core and total worth of three rods with different positions are also calculated. Finally, the effect of the axial and radial neutron flux in reactor core which is caused by the control rods is simulated. The simulation results of the control rods meet design requirements for TMSR.

Minimizing torque ripple in a brushless DC motor with fuzzy logic: applied to control rod driving mechanism of MNSR

A permanent magnet BLDC(brushless direct current) motor is used to move the control rod of a miniature neutron source reactor(MNSR). The BLDC motor drive is modeled using MATLAB/SIMULINK. Two main parts of the modeling are the inverter switching and the current control. Current control with chopping used to minimize the torque ripple of the MNSR control rod drive. Fuzzy logic current control together with soft chopping control shows the best response of all the three strategies. The prototype drive mechanism has an ATmega32 controller and power MOSFET switches. The simulation results are compared with experimental drive mechanism.

Control rod drive for high temperature gas cooled reactor

ＣｏｎｔｒｏｌｒｏｄｄｒｉｖｅｆｏｒｈｉｇｈｔｅｍｐｅｒａｔｕｒｅｇａｓｃｏｏｌｅｄｒｅａｃｔｏｒＤｅｎｇＪｕｎＸｉａｎ，ＸｕＪｉＭｉｎｇ，ＸｉａｏＳｈｕＲｕ，ＺｈａｎｇＨａｎ，ＹａｎｇＳｈｅｎＨｕａ，ＬｉｕＡｉＪｕｎ，ＺｈａｎｇＥｎＨ...

Control Rod Calibration and Worth Calculation for Optimized Power Reactor 1000 (OPR-1000) Using Core Simulator OPR1000

Control rod is used to change the power in nuclear reactor.?Certainly, the core at any moment can be made subcritical condition and shut downs when occurring?to emergency instance in the core. The rod is grouped based?on their function and located at different places in the core where their feature is maximized.?Two methods of control rod calibration are the asymptotic period method and the rod-drop method, which were applied in this experiment. In the first method, the reactor is made supcritical by inserting the control rod to be calibrated a certain level. The rod drop method is to determine the subcritical;at the critical state, the rod to be calibrated is dropped into the core, and the resulting decay of neutron flux is observed and related to the reactivity. In this paper, the regulating rod will be calibrated according to the reactivity in OPR-1000 that corresponds to a certain control rod insert or withdraw, and the reactivity in power reactor depends?on the integral and differential control rod group too. The core simulator OPR1000 is used to test those methods.

On Line Measurement of Reactivity Worth of TRIGA Mark-II Research Reactor Control Rods

The reactivity worth measurement system for control rods of the TRIGA MARK-II research reactor of Bangladesh has been design and developed. The theory of the kinetic technique of measuring reactivity has been used by this measurement system. The system comprises of indigenous hardware and software for online acquisition of neutron flux signals from reactor console and then computes the reactivity worth accordingly. Here for the TRIGA MARK-II research reactor, the reactivity measurement system was implemented with a dedicated circuit assembly and a conventional personal computer. A high-level Visual Basic real-time programming has been developed for data acquisition, reactivity calculation, online display (numerically as well as graphically), saving data, etc. To measure reactivity worth of TRIGA reactor control rods the rod drop experimental technique has been adopted. The results of tests experiments, carried out with the rod drop method for measuring various reactivity worth of control rods have been presented in the paper. A comparison between this results with the results using period method and that of computation method, demonstrated that the response of this reactivity measurement system is fast enough to monitor and measure the safety-related reactivity and power excursions in the reactor.

Controlling chaos based on a novel intelligent integral terminal sliding mode control in a rod-type plasma torch

An integral terminal sliding mode controller is proposed in order to control chaos in a rod-type plasma torch system.In this method, a new sliding surface is defined based on a combination of the conventional sliding surface in terminal sliding mode control and a nonlinear function of the integral of the system states. It is assumed that the dynamics of a chaotic system are unknown and also the system is exposed to disturbance and unstructured uncertainty. To achieve a chattering-free and high-speed response for such an unknown system, an adaptive neuro-fuzzy inference system is utilized in the next step to approximate the unknown part of the nonlinear dynamics. Then, the proposed integral terminal sliding mode controller stabilizes the approximated system based on Lyapunov＇s stability theory. In addition, a Bee algorithm is used to select the coefficients of integral terminal sliding mode controller to improve the performance of the proposed method. Simulation results demonstrate the improvement in the response speed, chattering rejection, transient response,and robustness against uncertainties.

透明空腔复合滤棒成型纸恒张力控制系统设计

在滤棒成型过程中,包裹基棒的成型纸的张力稳定性对滤棒中基棒间距的稳定性具有较大影响。为提高透明空腔复合滤棒产品质量,对成型纸的输送进行恒张力控制。针对透明成型纸的材质特殊性,设计了透明空腔复合滤棒卷制成型过程中成型纸恒张力控制系统,采用闭环伺服控制原理,解决了透明成型纸在滤棒卷制过程中,因张力波动大导致的滤棒质量问题。测试结果表明,透明成型纸在10N的拉力作用下长度方向变形率为0.5%,对于120mm滤棒,在急速升速过程中,最大张力波动值0.21N所引起的长度方向变形为0.012mm,对于滤棒±0.8mm的误差许可范围基本没有影响。在生产透明空腔复合滤棒的YL22滤棒成型机组上的生产应用结果显示,成型纸恒张力控制系统实现了成型纸的恒张力控制,提高了基棒定位准确性,消除了因张力引起的滤棒空腔尺寸的波动,提高了产品质量,满足滤棒稳定生产要求。

PCTRAN Westinghouse AP1000 Power Control of Pressurized Water Reactor Using Simulink of MATLAB

This paper introduces the simulation, and controls using Simulink of MATLAB for PCTRAN (Personal Computer Transient Analysis) of the power control system (PWR) type pressurized water reactor of PWR WESTINGHOUSE AP1000. The power controller model produces mathematical model description in nonlinear relation form in Simulink of MATLAB which is an important and popular program used at most universities for education. The power controller is described by a block diagram in this paper and some details introduce to clearly understand the work function. The results of action control compared with the PCTRAN programme in modes of automatic and manual control.

Fluid Flow Past a Circular Cylinder with Tandem Rod and Staggered Rod at Low Reynolds Number

The flow past a primary cylinder with one tandem control rod and one staggered control rod is simulated in this paper through solving the Navier-Stokes equations. Two examples are simulated to validate the model, and the results matched well with those of previous researches. The Reynolds number based on the diameter of the primary cylinder is 500. The diameter ratio between the control rod and the primary cylinder （d/D） is 0.25. It was found that the effect of the combination of one upstream tandem control rod and one staggered control rod on the hydrodynamics of the primary cylinder is a linear superposition of the effect of a corresponding single control rod, and the effect of the upstream tandem control rod is dominant at larger spacing ratios such as G/D=2. For the combination of a downstream tandem control rod and a staggered control rod, the effect of the control rods is different from that of the corresponding single control rod in the region of 0.2〈G/D〈0.5 ＆ 30°〈a〈120° and 0.9〈G/D〈1.4 ＆ 30°〈a〈50°, where the additional effect is obvious. In this case, the effect of the downstream tandem control rod is dominant at small spacing ratios （such as G/D=0.1）. At moderate spacing ratios such as G/D=0.4, the effects of the tandem control rod and the staggered control rod are comparable in both cases.

国内煤矿锚杆钻机应用现状及发展趋势

按照单体锚杆钻机、全液压履带式锚杆钻车及电液自动化锚杆钻车三类介绍了锚杆钻机在国内煤矿的应用现状,指出各类锚杆钻机在实际应用中存在的问题。结合国内煤矿井下巷道掘进的特点,分析了锚杆钻机的技术特点与适用性,研究了国内煤矿锚杆钻机的发展方向,提出了电动锚杆钻车的思路及实现方式。

KDF-M成型机滤棒圆周CPK值优化研究

在滤棒生产过程中,提高圆周过程能力指数(CPK值)是保证滤棒质量有效的方法之一。该文为提高KDF-M成型机滤棒圆周过程质量控制能力,针对影响滤棒圆周稳定性的部位进行改进。通过加装纸边辅助调节器,使纸边平稳运行从而保障圆周稳定;通过降低鱼雷辊故障频率优化其支撑位置,减少圆周波动;通过改进压板定位螺丝,减少压板位移造成圆周不稳;设计光学直径检测装置(ODM)专用清洁工具,能快速彻底清除积垢提高圆周检测的准确性。结果表明,通过以上改进方法成功提升滤棒圆周CPK值,从而保证卷烟质量。

Multiple fault diagnosis of down-hole conditions of sucker-rod pumping wells based on Freeman chain code and DCA

It is important to achieve continuous, stable and efficient pumping well operation in actual oilfield operation. Down-hole pumping well working conditions can be monitored in real-time and a reasonable production scheme can be designed when computer diagnosis is used. However, it is difficult to make a comprehensive analysis to supply efficient technical guidance for operation of the pumping well with multiple faults of down-hole conditions, which cannot be effectively dealt with by the common methods. To solve this problem, a method based on designated component analysis （DCA） is used in this paper. Freeman chain code is used to represent the down-hole dynamometer card whose important characteristics are extracted to construct a designated mode set. A control chart is used as a basis for fault detection. The upper and lower control lines on the control chart are determined from standard samples in normal working conditions. In an incompletely orthogonal mode, the designated mode set could be divided into some subsets in which the modes are completely orthogonal. The observed data is projected into each designated mode to realize fault detection according to the upper and lower control lines. The examples show that the proposed method can effectively diagnose multiple faults of down-hole conditions.

控制杆-强制旋转对圆柱涡激振动的抑制作用研究

为实现圆柱涡激振动的高效抑制,本文基于控制杆-强制旋转组合结构讨论圆柱涡激振动的抑制问题。对低雷诺数下的圆柱涡激振动进行数值模拟研究,对比分析不同控制杆数量和圆柱转速比下的流场特性、振动响应和流体力响应等。结果表明:与裸圆柱相比,控制杆具有一定的涡激振动抑制效果;对于三、五控制杆,通过调节转速比,可以实现最高98%的圆柱振幅抑制(对三控制杆,转速比为0.4~0.6;对五控制杆,转速比为0~0.2);圆柱振幅抑制与圆柱减阻区间相同;对于四、六控制杆,旋转对振幅抑制的影响较小;主圆柱表面的漩涡脱落和漩涡的合并会引起流体力系数的高幅波动,导致圆柱高振幅响应;没有漩涡合并和圆柱表面脱涡不明显时,流体力系数则无明显波动,圆柱振幅也显著降低。

农用推杆电机行程控制算法研究

研究实现了一种农用推杆电机的低成本行程控制算法。该算法基于霍尔计数原理,通过给普通农用推杆电机加装2个霍尔传感器使得电机运行时输出2路方波信号来实现。电机运行时每转一圈会触发霍尔传感器输出一个脉冲信号,2路信号具有90°的相位差,通过2路信号的相位关系可判断出电机的正反转状态并据此对脉冲信号进行加数计数或减数计数,算法根据用户设置的行程百分比、霍尔计数值以及全行程霍尔计数总值实现电机行程的自动控制。该算法具有行程控制稳定可靠、实现成本低、适用于农业高湿多尘环境等优点,可应用于设施农业和大田农业中相关设备的现场自动控制以及基于农业物联网的远程精准控制。

Development of integrated reheating,rolling and cooling models for stelmor production line

Production characteristics of high speed rod are fast speed,complex section and internal microstructure evolution,which bring great problems to analyze and solve the quality disputes.Therefore,a serial process models have been developed based on the characteristics of high speed rod:due to rod stock to be square section,a two dimension model has been developed to predict the evolution of internal temperature and grain coarsening.As for the rod rolling process,an automatic section design system has been written, which can show section filling condition and process parameters such as temperature,pressure and recrystallization etc per pass.As for rod cooling stage,an integrated model which coupled phase transformation,temperature and final properties was developed and applied in real production with good results.

长寿期小型棒控压水堆控制棒方案研究

小型棒控压水堆舍弃了可溶硼,并高度依赖控制棒与可燃毒物棒控制堆芯的反应性。为研究控制棒对堆芯关键性能的影响,本文以核动力破冰船用KLT-40模型为对象,以轴向功率偏移、堆芯寿期、燃料利用率与径向功率峰因子为指标,开展长寿期小型棒控压水堆控制棒布置与动作策略设计分析。首先,基于OpenMC程序开发带棒燃耗程序;其次,比较堆芯带控制棒与无控制棒运行时的堆芯寿期等指标;最后,分析不同动作策略对轴向功率偏移等指标的影响。结果表明:控制棒将堆芯寿期从590 EFPDs(等效满功率天,Effective full power days)延长至650~698 EFPDs;低价值棒组优先动作策略使轴向功率偏移程度由−0.69与+0.80分别下降至−0.29与+0.52。因此,要准确计算长寿期压水堆寿期必须采用带控制棒燃耗计算策略,并且通过合理的动作策略能够有效减小控制棒带来的轴向功率偏移。

唐山矿托煤顶巷道支护参数设计与优化

为研究深部托煤顶巷道围岩变形特征,以唐山矿0293工作面为背景,基于普氏拱理论分析了巷道围岩顶板及两帮的破坏深度,根据工作面赋存条件,采用FLAC3D软件模拟架棚和锚杆两种支护方式并进行对比,得到最佳的支护形式为“锚杆+锚索”。设定7种不同参数的锚杆支护方案,进一步进行模拟比较得到最优方案。研究结果表明:理论上0293工作面巷道顶板破坏深度在3.03 m,巷道两帮破坏深度在2.81 m;唐山矿托煤顶巷道围岩的煤体较软,具有较大的变形量,锚杆(索)对于巷道围岩变形的控制明显优于架棚支护。确定最优的托煤顶巷道支护方案为:顶锚杆间排距700 mm×700 mm,顶锚索间排距1400 mm×1400 mm,3根锚索,帮锚杆700 mm×700 mm,帮锚索4500 mm,每排2根时,对巷道围岩变形的控制效果最好。

卷烟滤棒成型加工区域集控系统实现

针对滤棒成型作业区分散、设备种类多、制造厂家和数量多、接口协议复杂且不统一以及海量数据变量难识别等问题,设计并开发了基于OPC UA架构和实时内存数据库的就地滤棒加工区数采和监控系统。自主开发OPC服务器,实现了滤棒成型主、辅设备的实时数据采集,并通过高效内存数据库服务器对生产及设备信息进行海量存储,进而实现了对滤棒成型车间生产过程信息的全面、准确迁移集成,以及对滤棒生产、产量、质量、机台效率、设备状态等信息的可视化区域集控。