Strip Layer Method for Analysis of the Three-Dimensional Stresses and Spread of Large Cylindrical Shell Rolling

As the traditional forging process has many problems such as low efficiency, high consumption of material and energy, large cylindrical shell rolling is introduced. Large cylindrical shell rolling is a typical rotary forming technology, and the upper and lower rolls have different radii and speeds. To quickly predict the three-dimensional stresses and eliminate fishtail defect, an improved strip layer method is developed, in which the asymmetry of the upper and lower rolls, non-uniform deformation and stress, as well as the asymmetrical spread on the end surface are considered. The deformation zone is divided into a certain number of layers and strips along the thickness and width, respectively. The transverse displacement model is constructed by polynomial function, in order to increase the computation speed greatly. From the metal plastic mechanics principle, the three-dimensional stress models are established. The genetic algorithm is used for optimization calculation in an industrial experiment example. The results show that the rolling pressure, the normal stresses, the upper and lower friction stress distributions are not similar with those of a general plate rolling. There are two relative maximum values in rolling pressure distribution. The upper and lower longitudinal friction stresses change direction nearby the upper and lower neutral points, respectively. The fishtail profile of spread on the end surface is predicted satisfactorily. The reduction could be helpful to eliminate fishtail defect. The large cylindrical shell rolling example illustrates the calculation results acquired rapidly are good agreements with the finite element simulation and experimental values of previous study. A highly effective and reliable three-dimensional simulation method is proposed for large cylindrical shell rolling and other asymmetrical rolling.

ANALYSIS OF ROLLING BY ELASTO-PLASTIC FINITE DEFORMATION CONTACT BOUNDARY ELEMENT METHOD

A multinonlinear boundary element method is established dealing with elasto plastic finite deformation contact problem, and it is employed to analysis rolling process. With rollers as elastic bodies, workpieces as elastio plastic bodies, rolling problem can be viewed as a frictional elasto plastic contact problem. With fewer assumptions in the simulation of the rolling process, a novel and accurate method is proposed for analysis of rolling problems.

Study of the impacts of upstream natural gas market reform in China on infrastructure deployment and social welfare using an SVM-based rolling horizon stochastic game analysis

Natural gas is expected to play a much more important role in China in future decades, and market reform is crucial for its rapid market penetration. At present, the main gas fields, pipelines and liquefied natural gas(LNG) infrastructure are mainly monopolized by large state-owned companies, and one of the important market reform policies is to open up LNG import rights to smaller private companies and traders. Therefore, in the present study, a game theoretical model is proposed to analyze and compare the impacts of different market structures on infrastructure deployment and social welfare. Moreover, a support vector machine-based rolling horizon stochastic method is adopted in the model to simulate real LNG price fluctuations. Four market reform scenarios are proposed considering different policies such as business separation, third-party access(TPA) and their combinations. The results indicate that, with third-party access(TPA)entrance into the LNG market, the construction of LNG infrastructure will be promoted and more gas will be provided at lower prices, and thus the total social welfare will be improved greatly.

Influence of process parameters on the microstructural evolution of a rear axle tube during cross wedge rolling

In the shaping process of cross wedge rolling（CWR）, metal undergoes a complex microstructural evolution, which affects the quality and mechanical properties of the product. Through secondary development of the DEFORM-3D software, we developed a rigid plastic finite element model for a CWR-processed rear axle tube, coupled with thermomechanical and microstructural aspects of workpieces. Using the developed model, we investigated the microstructural evolution of the CWR process. Also, the influence of numerous parameters, including the initial temperature of workpieces, the roll speed, the forming angle, and the spreading angle, on the grain size and the grain-size uniformity of the rolled workpieces was analyzed. The numerical simulation was verified through rolling and metallographic experiments. Good agreement was obtained between the calculated and experimental results, which demonstrated the reliability of the model constructed in this work.

THREE DIMENSIONAL ELASTO-PLASTIC CONTACT BOUNDARY ELEMENT ANALYSIS FOR ROLLING WITH CONSIDERATION OF FRICTION

The boundary element method in framework is given to evaluate three dimensional frictional contact problems. Elasto plastic material behavior is taken into account by mean of an initial stress formulation and Von Mises yield criterion. The amount of tangential traction at contact surface is limited by Coulomb's friction law and constant shear rule. From some numerical results of a plate rolling problem, it is demonstrated here that the BEM can be used to efficiently and accurately analyze this class of forming problems.

A 3-D Differential Method for Solving Rolling Force of PC Hot Strip Mill

The character of the deformation zone on pair cross rolls is different from that of the regular 4-high mill. Considering comprehensive influences of normal stress and shear stress in rolling direction, width direction and thickness direction, the rolling force calculation model of the PC （pair crossed） hot strip mill is built. Taking the entry stress and the exit stress of strip as the boundary conditions, the longitudinal and transverse distribution of rolling force is worked out by the differential method. Then the total rolling force is calculated, and calculated results are verified by experimental data.

Analysis on Shear Deformation for High Manganese Austenite Steel during Hot Asymmetrical Rolling Process Using Finite Element Method

Based on the rigid-plastic finite element method（FEM）, the shear stress field of deformation region for high manganese austenite steel during hot asymmetrical rolling process was analyzed. The influences of rolling parameters, such as the velocity ratio of upper to lower rolls, the initial temperature of workpiece and the reduction rate, on the shear deformation of three nodes in the upper, center and lower layers were discussed. As the rolling parameters change, distinct shear deformation appears in the upper and lower layers, but the shear deformation in the center layer appears only when the velocity ratio is more than 1.00, and the absolute value of the shear stress in this layer is changed with rolling parameters. A mathematical model which reflected the change of the maximal absolute shear stress for the center layer was established, by which the maximal absolute shear stress for the center layer can be easily calculated and the appropriate rolling technology can be designed.

Finite Element Simulation of Flexible Roll Forming with Supplemented Material Data and the Experimental Verification

Flexible roll forming is a promising manufacturing method for the production of variable cross section products. Considering the large plastic strain in this forming process which is much larger than that of uniform deformation phase of uniaxial tensile test, the widely adopted method of simulating the forming processes with non-supplemented material data from uniaxial tensile test will certainly lead to large error. To reduce this error, the material data is supplemented based on three constitutive models. Then a finite element model of a six passes flexible roll forming process is established based on the supplemented material data and the original material data from the uniaxial tensile test. The flexible roll forming experiment of a B pillar reinforcing plate is carried out to verify the proposed method. Final cross section shapes of the experimental and the simulated results are compared. It is shown that the simulation calculated with supplemented material data based on Swift model agrees well with the experimental results, while the simulation based on original material data could not predict the actual deformation accurately. The results indicate that this material supplement method is reliable and indispensible, and the simulation model can well reflect the real metal forming process. Detailed analysis of the distribution and history of plastic strain at different positions are performed. A new material data supplement method is proposed to tackle the problem which is ignored in other roll forming simulations, and thus the forming process simulation accuracy can be greatly improved.

Analysis of Sheet Curvature in Asymmetrical Cold Rolling

In asymmetric cold rolling, the workpiece is often bent downwards or upwards. A two-dimensional explicit dynamic finite element model with Arbitrary Lagrangian Eulerian （ALE） adaptive meshing technique has been employed to simulate asymmetrical sheet rolling, in which asymmetrical conditions are here due to different roll radii. To validate the simulation, the results of simulation and experiment are compared. Effects of asymmetry due to roll radii mismatch on the normal and shear distributions and on sheet curvature variations are discussed. An optimum roll radii ratio could be found to produce flat sheet. Trials were conducted to investigate the effectiveness of roll radii mismatch as an approach of sheet curvature control.

Effect of rolling friction on wall pressure,discharge velocity and outflow of granular material from a flat-bottomed bin

The present paper provides both experimental and DEM analyses of the filling and discharge of pea grains from a 3D flat-bottomed bin. In the DEM model, the fixed mean values of the experimentally determined single particle data, such as the particle density, Young＇s modulus, Poisson＇s ratio as well as the sliding and rolling friction coefficients were incorporated to analyse their effects on the macroscale indicators, such as the wall pressure, discharge velocities and material outflow parameters. The effect of rolling friction was studied based on the experimentally measured single particle rolling friction coefficient. This analysis is aimed at the quantitative prediction of flow parameters as related to the identification of material parameters.

Plate Shape Control Theory and Experiment for 20-high Mill

Roll flattening theory is an important part of plate shape control theories for 20-high mill. In order to improve the accuracy of roll flattening calculation for 20-high mill, a new and more accurate roll flattening model was proposed. In this model, the roll barrel was considered as a finite length semi-infinite body. Based on the boundary integral equation method, the numerical solution of the finite length semi-infinite body under the distributed force was obtained and an accurate roll flattening model was established. Coupled with roll bending model and strip plastic deformation, a new and more accurate plate control model for 20-high mill was established. Moreover, the effects of the first intermediate roll taper angle and taper length were analyzed. The tension distribution calculated by analytical model was consistent with the experimental results.