A mathematical model was established to describe the direct reduction of pellets in a rotary hearth furnace （RHF）. In the model, heat transfer, mass transfer, and gas-solid chemical reactions were taken into account...A mathematical model was established to describe the direct reduction of pellets in a rotary hearth furnace （RHF）. In the model, heat transfer, mass transfer, and gas-solid chemical reactions were taken into account. The behaviors of iron metallization and dezincification were analyzed by the numerical method, which was validated by experimental data of the direct reduction of pellets in a Si-Mo furnace. The simulation results show that if the production targets of iron metallization and dezincification are up to 80% and 90%, respectively, the furnace temperature for high-temperature sections must be set higher than 1300~ C. Moreover, an undersupply of secondary air by 20% will lead to a decline in iron metallization rate of discharged pellets by 10% and a decrease in dezincing rate by 13%. In addition, if the residence time of pellets in the furnace is over 20 min, its further extension will hardly lead to an obvious increase in production indexes under the same furnace temperature curve.展开更多
In this study,innovative ellipsoid pellet with craters on its surface was designed,and the direct reduction process was compared with ellipsoid(without craters)and sphere pellets.In addition,furnace temperature and un...In this study,innovative ellipsoid pellet with craters on its surface was designed,and the direct reduction process was compared with ellipsoid(without craters)and sphere pellets.In addition,furnace temperature and uneven heat flux density effects on the pellet direct reduction process were also studied.The results show that ellipsoid pellet is better than that of spherical pellet on metallization ratio.However,under the condition of non-uniform heat flow,the ellipsoid pellet final metallization rate and zinc removal rate were lower.Although the heat transfer effect of ellipsoid pellet with craters was not improved significantly,the metallization rate and zinc removal rate were found improved,which will have a cumulative effect on the pellets direct reduction process in rotary hearth furnace.Under varying furnace temperature conditions,the pellet temperature was higher than that of the constant furnace temperature.After 1200 s,pellet Fe concentration increased to 123.6%,metallization rate and zinc removal rate increased to 113.7%and 102.2%,respectively.These results can provide references for the carbon-containing pellet design used in rotary hearth furnace.展开更多
Direct reduction of dust composite pellets containing zinc and iron was examined by simulating the conditions of actual production process of a rotary hearth furnace （RHF） in laboratory. A mathematical model was con...Direct reduction of dust composite pellets containing zinc and iron was examined by simulating the conditions of actual production process of a rotary hearth furnace （RHF） in laboratory. A mathematical model was constructed to study the reduction kinetics of iron oxides and ZnO in the dust composite pellets. It was validated by comparing the calculated values with experimental results. The effects of furnace temperature, pellet radius, and pellet porosity on the reduction were investigated by the model. It is shown that furnace temperature has obvious influence on both of the reduction of iron oxides and ZnO, but the influence of pellet radius and porosity is much smaller. Model calculations suggest that both of the reduction of iron oxides and ZnO are under mixed control with interface reactions and Boudouard reaction in the early stage, but only with interface reactions in the later stage.展开更多
基金financially supported by the National Key Basic Research and Development Program of China(No. 2012CB720405)
文摘A mathematical model was established to describe the direct reduction of pellets in a rotary hearth furnace （RHF）. In the model, heat transfer, mass transfer, and gas-solid chemical reactions were taken into account. The behaviors of iron metallization and dezincification were analyzed by the numerical method, which was validated by experimental data of the direct reduction of pellets in a Si-Mo furnace. The simulation results show that if the production targets of iron metallization and dezincification are up to 80% and 90%, respectively, the furnace temperature for high-temperature sections must be set higher than 1300~ C. Moreover, an undersupply of secondary air by 20% will lead to a decline in iron metallization rate of discharged pellets by 10% and a decrease in dezincing rate by 13%. In addition, if the residence time of pellets in the furnace is over 20 min, its further extension will hardly lead to an obvious increase in production indexes under the same furnace temperature curve.
基金Project(cstc 2018 jszx-cyzdx 0100)supported by the Chongqing Technology Innovation and Application Demonstration Project,China。
文摘In this study,innovative ellipsoid pellet with craters on its surface was designed,and the direct reduction process was compared with ellipsoid(without craters)and sphere pellets.In addition,furnace temperature and uneven heat flux density effects on the pellet direct reduction process were also studied.The results show that ellipsoid pellet is better than that of spherical pellet on metallization ratio.However,under the condition of non-uniform heat flow,the ellipsoid pellet final metallization rate and zinc removal rate were lower.Although the heat transfer effect of ellipsoid pellet with craters was not improved significantly,the metallization rate and zinc removal rate were found improved,which will have a cumulative effect on the pellets direct reduction process in rotary hearth furnace.Under varying furnace temperature conditions,the pellet temperature was higher than that of the constant furnace temperature.After 1200 s,pellet Fe concentration increased to 123.6%,metallization rate and zinc removal rate increased to 113.7%and 102.2%,respectively.These results can provide references for the carbon-containing pellet design used in rotary hearth furnace.
基金financially supported by the National Basic Research Program of China (No. 2012CB720401)the National Key Technology Research and Development Program of China (No. 2011BAC01B02)
文摘Direct reduction of dust composite pellets containing zinc and iron was examined by simulating the conditions of actual production process of a rotary hearth furnace （RHF） in laboratory. A mathematical model was constructed to study the reduction kinetics of iron oxides and ZnO in the dust composite pellets. It was validated by comparing the calculated values with experimental results. The effects of furnace temperature, pellet radius, and pellet porosity on the reduction were investigated by the model. It is shown that furnace temperature has obvious influence on both of the reduction of iron oxides and ZnO, but the influence of pellet radius and porosity is much smaller. Model calculations suggest that both of the reduction of iron oxides and ZnO are under mixed control with interface reactions and Boudouard reaction in the early stage, but only with interface reactions in the later stage.
