Enhancement in solar hydrogen generation efficiency using InGaN photoelectrode after surface roughening treatment with nano-sized Ni mask

A significant enhancement in solar hydrogen generation efficiency has been achieved by inductive coupled etching （ICP） surface roughening treatment using nano-sized nickel mask. As much as 7 times improvement of photocurrent is demonstrated in comparison with a planar one fabricated from the same parent wafer. Under identical illumination conditions in HBr solution, the incident photon conversion efficiency （IPCE） shows an enhancement with a factor of 3, which even exceed 54% at 400 nm wavelength. We believe the enhancement is attributed to several facts including improvement in absorption, reacting area, carder localization and carrier lifetime.

Kinetic roughening transition and missing regime transition of melt crystallized polybutene-1 tetragonal phase: growth kinetics analysis

The morphology and lateral growth rate of isotactic polybutene-1(it-PB1)have been investigated for crystallization from the melt over a wide range of crystallization temperatures from 50 to 110℃.The morphology of it-PB1 crystals is a rounded shape at crystallization temperatures lower than 85℃,while lamellarsingle crystals possess faceted morphology at higher crystallization temperatures.The kinetic roughening transi-tion occurs around 85℃.The nucleation and growth mechanism for crystallization does not work below 85℃,since the growth face is rough.However,the growth rate shows the supercooling dependence derived from the nucleation and growth mechanism.The nucleation theory seems still to work even for rough surface growth.Possible mechanisms for the crystal growth of this polymer are discussed.

Improved light extraction of wafer-bonded AlGalnP LEDs by surface roughening

By using the wafer bonding technique and wet etching process,a wafer bonded thin film AlGaInP LED with wet etched n-AlGaInP surfaces was fabricated.The morphology of the etched surface exhibits a pyramid-like feature.The wafer was cut into 270×270μm2 chips and then packaged into TO-18 without epoxy resin.With 20-mA current injection,the light intensity and output power of LED-Ⅰwith surface roughening respectively reach 315 mcd and 4.622 mW,which was 1.7 times higher than that of LED-Ⅱwithout surface roughening.The enhancement of output power in LED-Ⅰcan be attributed to the pyramid-like surface,which not only reduces the total internal reflection at the semiconductor-air interface but also effectively guides more photons into the escape angle for emission from the LED device.

Improved light extraction of GaN-based light-emitting diodes with surface-textured indium tin oxide electrodes by nickel nanoparticle mask dry-etching

GaN-based light-emitting diodes （LEDs） with surface-textured indium tin oxide （ITO） as a transparent current spreading layer were fabricated. The ITO surface was textured by inductively coupled plasma （ICP） etching technology using a monolayer of nickel （Ni） nanoparticles as the etching mask. The luminance intensity of ITO surface-textured GaN-based LEDs was enhanced by about 34% compared to that of conventional LED without textured ITO layer. In addition, the fabricated ITO surface-textured GaN-based LEDs would present a quite good performance in electrical characteristics. The results indicate that the scattering of photons emitted in the active layer was greatly enhanced via the textured ITO surface, and the ITO surface-textured technique could have a potential application in improving photoelectric characteristics for manufacturing GaN-based LEDs of higher brightness.

SOLUTION CRYSTALLIZATION OF METALLOCENE SHORT CHAIN BRANCHED POLYETHYLENE:MORPHOLOGY AND MECHANISM

Solution crystallization of metallocene short chain branched polyethylene (SCBPE) was carried out and very nice single crystals were obtained. Compared with single crystals grown from linear polyethylene, SCBPE single crystals are dirty due to intermolecular heterogeneity The crystal morphology changes with crystallization temperatures. Lozenge, truncated lozenge, hexagonal, rounded and elongated crystal morphologies have been found at much lower crystallization temperature than in linear polyethylene. The electron diffraction shows there is a possibility that the single crystals may have hexagonal packing in a crystallization temperature range. The lateral habits of single crystal are discussed based on roughening theories.

PRETREATMENT FOR METALLIZATION OF PZT CERAMIC SURFACES

This paper describes the pretreatment process for metal[ization of PZT ceramics surfaces by electrolytic Ni plating which includes cleaning, roughening, sensitization and activation. The experimental procedure, results and influeneing factors for these processes are investigated and discussed.

Enginered Interfaces for Adherent Coatings

Two methods used to grow adherent coatings, roughening of the surface for mechanical interlocking and the use of chemically compatible interlayers having intermediate thermal expansion coefficients are analyzed numerically with the aid of phase diagram. Calculations indicate that more roughness and smaller periodicity of the substrate surface will increase the interfacial area and thus enhance the adherence strength of the coating. The phase diagram shows that an intermediate layer with a proper composition gradient from the substrate to the film will relax the thermal stress at the interface effectively.

Numerical Study of the Influence of Grain Size and Loading Conditions on the Deformation of a Polycrystalline Aluminum Alloy

This work is concerned with numerical simulations of surface roughening in a polycrystalline aluminum alloy. Using 3D finite difference model, high-resolution simulations are conducted. Effects of loading conditions and grain size on surface roughening and mesoscale deformation processes in AL6061-T3 aluminum alloy under quasistatic uniaxial tension are investigated.

Electrical characteristics of a vertical light emitting diode with n-type contacts on a selectively wet-etching roughened surface

Low resistance and thermally stable n-type contacts to N-polar GaN are essentially important for vertical light emitting diodes （VLEDs）. The electrical characteristics of VLEDs with n-type contacts on a roughened and flat N-polar surface have been compared. VLEDs with contacts deposited on a roughened surface exhibit lower leakage currents yet a higher operating voltage. Based on this, a new scheme by depositing metallization contacts on a selectively wet-etching roughened surface has been developed. Excellent electrical and optical characteristics have been achieved with this method. An aging test further confirmed its stability.

Surface micro/nanostructure evolution of Au-Ag alloy nanoplates： Synthesis, simulation, plasmonic photothermal and surface-enhanced Raman scattering applications

This study reports the controllable surface roughening of Au-Ag alloy nanoplates via the galvanic replacement reaction between single-crystalline triangular Ag nanoplates and HAuC14 in an aqueous medium. With a combination of experimental evidence and finite element method （FEM） simulations, improved electromagnetic field （E-field） enhancement around the surface-roughened Au- Ag nanoplates and tunable light absorption in the near-infrared （NIR） region （-800-1,400 nm） are achieved by the synergistic effects of the localized surface plasmon resonance （LSPR） from the maintained triangular shape, the controllable Au-Ag alloy composition, and the increased surface roughness. The NIR light extinction enables an active photothermal effect as well as a high photothermal conversion efficiency （78.5%）. The well-maintained triangular shape, surface- roughened evolutions of both micro- and nanostructures, and tunable NIR surface plasmon resonance effect enable potential applications of the Au-Ag alloy nanoplates in surface-enhanced Raman spectroscopic detection of biomolecules through 785-nm laser excitation.

A general mechanism of grain growth-Ⅰ.Theory

The behaviors of grain growth dominate the formation of the microstructure inside polycrystalline materials and thus strongly influence their practical performances.However,grain growth behaviors still remain ambiguous and thus lack a mathematical formula to describe the general evolution despite decades of efforts.Here,we propose a new migration model of grain boundary(GB)and further derive a mathematical expression to depict the general evolution of grain growth in the cellular structures.The expression incorporates the variables influencing growth rate(e.g.GB features,grain size and local grain size distribution)and thus reveals how the normal,abnormal and stagnant behaviors of grain growth occur in polycrystalline systems.In addition,our model correlates quantitatively GB roughening transition with grain growth behavior.The general growth theory may provide new insights into the GB thermodynamics and kinetics during the cellular structure evolution.

Rayleigh relaxation of pyrazine, pyridine and piperidine molecules adsorbed on the roughened Ag electrode by light beating technique

The light beating technique (intensity correlation algorithm) was employed to analyze the Rayleigh scattering from the roughened Ag electrode in very dilute (10^(-4)M) pyrazine, pyridine and piperidine aqueous solutions containing KCl (0.1 M). The relaxation time is longer when the applied voltages are between-0.4 V and-0.8 V(vs. SCE) where the Raman effect also shows greater surface enhancement. Also observed was that for the piperidine case the relaxation time reaches its maximum at the more negative applied voltage. The origin of the relaxation is attributed mainly to the desorp- tion process of the pyrazine. pyridine and piperidine molecules off the roughened Ag electrode. An. electrostatic model was also proposed for the interpretation of these experimental observations.