Damage assessment for seismic response of recycled concrete filled steel tube columns

A model for evaluating structural damage of recycled aggregate concrete filled steel tube （RCFST） columns under seismic effects is proposed in this paper. The proposed model takes the lateral deformation and the effect of repeated cyclic loading into account. Available test results were collected and utilized to calibrate the parameters of the proposed model. A seismic test for six RCFST columns was also performed to validate the proposed damage assessment model. The main test parameters were the recycled coarse aggregate （RCA） replacement percentage and the bond-slip property. The test results indicated that the seismic performance of the RCFST member depends on the RCA contents and their damage index increases as the RCA replacement percentage increases. It is also indicated that the damage degree of RCFST changes with the variation of the RCA replacement percentage. Finally, comparisons between the RCA contents, lateral deformation ratio and damage degree were implemented. It is suggested that an improvement procedure should be implemented in order to compensate for the performance difference between the RCFST and normal concrete filled steel tubes （CFST）.

Seismic performance of recycled concrete-filled square steel tube columns

An experimental study on the seismic performance of recycled concrete-filled square steel tube （RCFST） columns is carried out. Six specimens were designed and tested under constant axial compression and cyclic lateral loading. Two parameters, replacement percentage of recycled coarse aggregate （RCA） and axial compression level, were considered in the test. Based on the experimental data, the hysteretic loops, skeleton curves, ductility, energy dissipation capacity and stiffness degradation of RCFST columns were analyzed. The test results indicate that the failure modes of RCFST columns are the local buckling of the steel tube at the bottom of the columns, and the hysteretic loops are full and their shapes are similar to normal CFST columns. Furthermore, the ductility coefficient of all specimens are close to 3.0, and the equivalent viscous damping coefficient corresponding to the ultimate lateral load ranges from 0.323 to 0.360, which demonstrates that RCFST columns exhibit remarkable seismic performance.

Axial Bearing Capacity of Short FRP Confined Concrete-filled Steel Tubular Columns

The bearing capacity of FRP confined concrete-filled steel tubular （FRP-CFST） columns under axial compression was investigated. This new type of composite column is a concrete-filled steel tube （CFST） confined with fiber-reinforced polymer （FRP） wraps. Totally 11 short column specimens were tested to failure under axial compression. The influences of the type and quantity of FRP, the thickness of steel tube and the concrete strength were studied. It was found that the bearing capacity of short FRP-CFST column was much higher than that of comparable CFST column. Furthermore, the formulas for calculating the bearing capacity of the FRP-CFST columns are proposed. The analytical calculated results agree well with the experimental results.

Bearing capacity of composite columns reinforced by concrete filled steel tube

In this study, nine simplified short composite columns consisting of core CFST (concrete filled steel tube) of different diameters and outer reinforced concrete were constructed to study their compressive performance under axial or eccentric compression. The failure mode is characterized by the crush of the outer concrete. The bearing capacity increases at first and then decreases with further increase of the position coefficient. It can be concluded that position coefficient is an important structural parameter that has considerable influences on the ultimate bearing capacity of the composite columns. The outer concrete, steel tubes and longitudinal reinforcement are found to work in a cooperative manner under axial or eccentric compression when the position coefficient is about 0.5. An improved bearing capacity algorithm that takes the position coefficient into account has been proposed based on the experimental and simulation results and current technical specification in China. It has been proven to be precise and safe.

Seismic Behavior of Diaphragm-Through Connections of Concrete-Filled Square Steel Tubular Columns and H-Shaped Steel Beams

Based on the introductions of a type of diaphragm-through connection between concrete-filled square steel tubular columns (CFSSTCs) and H-shaped steel beams,a finite element model of the connection is developed and used to investigate the seismic behavior of the connection.The results of the finite element model are validated by a set of cyclic loading tests.The cyclic loading tests and the finite element analyses indicate that the failure mode of the suggested connections is plastic hinge at the beam with inelastic rotation angle exceeding 0.04 rad.The suggested connections have sufficient strength,plastic deformation and energy dissipation capacity to be used in composite moment frames as beam-to-column rigid connections.

Three-dimensional nonlinear analysis of creep in concrete filled steel tube columns

This paper proposes a based on 3D-VLE （three-dimensional nonlinear viscoelastic theory） three-parameters viscoelastic model for studying the time-dependent behaviour of concrete filled steel tube （CFT） columns. The method of 3D-VLE was developed to analyze the effects of concrete creep behavior on CFT structures. After the evaluation of the parameters in the proposed creep model, experimental measurements of two prestressed reinforced concrete beams were used to investigate the creep phenomenon of three CFT columns under long-term axial and eccentric load was investigated. The experimentally obtained time-dependent creep behaviour accorded well with the cu~＇es obtained from the proposed method. Many factors （such as ratio of long-term load to strength, slenderness ratio, steel ratio, and eccentricity ratio） were considered to obtain the regularity of influence of concrete creep on CFT structures. The analytical results can be consulted in the engineering practice and design.

Influence of Axial Load Ratio on Shear Behavior of Through-Diaphragm Connections of Concrete-Filled Square Steel Tubular Columns

Nonlinear finite element analysis and parametric studies were carried out to study the influence of axial load ratio on the shear behavior of the through-diaphragm connections of concrete-filled square steel tubular columns. The analysis reveals that smaller axial load ratio can improve the shear bearing capacity and ductility while larger axial load ratio will decrease the shear behavior of the through-diaphragm connections. The parametric studies indicate that the axial load ratio should be limited to less than 0.4 and its influence should be considered in the analysis and design of such connections.

Performance Investigation of Square Concrete-filled Steel Tube Columns

The behaviour of square concrete-filled steel tube columns under concentrical loading was studied. More than one hundred specimens were tested to investigate the effects of thickness of steel tube on the load carrying capacity of the concrete-filled tubular columns （CFTs）. The effect of the grade of concrete and content of expansive agent were also investigated. The effect of these parameters on the confinement of the concrete core was studied as well. From the experimental study it was found that for both CFTs with different strength grade concrete core, the ultimate load carrying capacity increases with the increase in percentage of expansive agent up to 20% but it again decreases at 25% of expansive agent content. It was also shown that the failure mode of CFTs depends on the strength grade of concrete core.

Prediction of Axial Capacity of Concrete-Filled Square Steel Tubes Using Neural Networks

The application of artificial neural network to predict the ultimate bearing capacity of CFST （ concrete-filled square steel tubes） short columns under axial loading is explored. Input parameters consiste of concrete compressive strength, yield strength of steel tube, confinement index, sectional dimension and width-to-thickness ratio. The ultimate bearing capacity is the only output parameter. A multilayer feedforward neural network is used to describe the nonlinear relationships between the input and output variables. Fifty-five experimental data of CFST short columns under axial loading are used to train and test the neural network. A comparison between the neural network model and three parameter models shows that the neural network model possesses good accuracy and could be a practical method for predicting the ultimate strength of axially loaded CFST short columns.

Analysis and seismic tests of composite shear walls with CFST columns and steel plate deep beams

A composite shear wall concept based on concrete filled steel tube （CFST） columns and steel plate （SP） deep beams is proposed and examined in this study. The new wall is composed of three different energy dissipation elements： CFST columns; SP deep beams; and reinforced concrete （RC） strips. The RC strips are intended to allow the core structural elements - the CFST columns and SP deep beams - to work as a single structure to consume energy. Six specimens of different configurations were tested under cyclic loading. The resulting data are analyzed herein. In addition, numerical simulations of the stress and damage processes for each specimen were carried out, and simulations were completed for a range of location and span-height ratio variations for the SP beams. The simulations show good agreement with the test results. The core structure exhibits a ductile yielding mechanism characteristic of strong column-weak beam structures, hysteretic curves are plump and the composite shear wall exhibits several seismic defense lines. The deformation of the shear wall specimens with encased CFST column and SP deep beam design appears to be closer to that of entire shear walls. Establishing optimal design parameters for the configuration of SP deep beams is pivotal to the best seismic behavior of the wall. The new composite shear wall is therefore suitable for use in the seismic design of building structures.

高强钢管超高性能混凝土短柱轴压承载力性能试验研究

为研究高强钢管内填超高性能混凝土(UHPC)的钢管混凝土短柱轴压性能,该文设计22根高强钢管UHPC短柱进行轴压试验,从破坏模式、荷载-纵向应变关系对试件的轴压性能进行对比分析,旨在通过径厚比、混凝土强度、截面类型等变化来探究高强钢管UHPC短柱的实际承载力性能差异.试验结果表明:高强钢管UHPC短柱的轴压性能受径厚比、混凝土强度影响较大;试件承载力随钢管壁厚增加而增加,但相同钢管直径和不同钢管直径增幅呈现不同规律.该文从延性、核心混凝土强度提高程度两个角度进行分析并提出高强钢管混凝土试件的相关参数设计建议.最后,将高强钢管UHPC短柱的轴压试验承载力结果与国内外规范GB 50936—2014、AIJ计算承载力结果进行对比,并基于极限平衡理论推导出高强圆钢管UHPC试件的轴压承载力计算公式,同时结合该文试验数据对其进行验证,证明了公式的准确性.

RPC外包方钢管混凝土柱轴压受力性能研究

为了研究活性粉末混凝土(Reactive powder concrete,RPC)外包方钢管混凝土柱的轴压受力性能,以RPC厚度和长细比为参数,对6根构件开展轴压试验研究,探讨该类组合柱的破坏模式、受力机理、套箍效应和承载力。试验结果表明:外层RPC可为内部方钢管混凝土柱提供较强的约束力,在受力后期套箍效应凸显。随着RPC厚度的增加,组合柱的承载力逐渐提高;随着组合柱长细比的增大,虽然其弹性刚度和承载力逐渐降低,但延性改善。采用ABAQUS软件建立RPC外包方钢管混凝土柱的有限元模型,分析RPC强度、RPC厚度、钢管强度等级、含钢率、内部混凝土强度和长细比等参数对组合柱承载力的影响规律,可得方钢管混凝土柱发挥系数的变化幅值为0.78~1.01。在试验研究、有限元参数分析和理论探讨的基础上,借鉴钢管混凝土结构技术规范,提出了RPC外包方钢管混凝土轴压短柱和长柱的承载力简化计算方法,公式计算值与已有数据样本吻合良好。

新型钢管混凝土梁柱节点力学性能试验研究

为研究内加强环式圆钢管混凝土柱与矩形钢管混凝土梁这种新型连接节点的力学性能,设计了缩尺钢管混凝土梁柱节点试件,开展了相同梁柱节点试件的静力加载试验和低周往复加载试验。通过研究该节点试件的破坏模式、荷载-位移曲线以及拟静力加载试验的骨架曲线、核心区剪切变形等,分析了节点试件的承载能力、延性和耗能能力,全面考察了同一梁柱节点在静力加载和低周往复加载两种工况下的受力性能和破坏模式。结果表明:钢管混凝土梁柱节点试件核心区强度较强,破坏模式主要为梁端破坏,低周往复加载试验时试件梁柱连接处附近的梁端钢板发生拉裂破坏和钢板鼓曲,静力加载试验时试件梁端焊缝发生拉裂破坏;试件延性较好,加载过程中经历了弹性、弹塑性和塑性发展阶段。最后提出了该类钢管混凝土梁柱节点核心区的抗剪强度计算公式。

反复荷载下圆钢管型钢再生混凝土组合柱恢复力模型研究

为建立圆钢管型钢再生混凝土组合柱的恢复力模型,对11根圆钢管型钢再生混凝土组合柱试件进行了低周反复荷载试验研究,考虑了再生骨料取代率、配钢率及钢管径厚比等不同设计参数的影响,分析了组合柱的地震破坏形态及滞回性能。基于组合柱的力学特征及曲线形状,提出了圆钢管型钢再生混凝土组合柱骨架曲线的三折线参数模型,采用理论推导与数据拟合的方法确定了组合柱骨架曲线的模型参数。在此基础上,给出了组合柱的滞回规则和卸载规律,构建了组合柱的恢复力模型,计算滞回曲线与试验滞回曲线吻合良好,表明该恢复力模型较好地反映了反复荷载下组合柱的受力特征点及滞回性能,可为此类组合柱的推广提供技术参考。

圆钢管型钢再生混凝土组合柱滞回性能非线性有限元分析

基于圆钢管型钢再生混凝土组合柱低周反复荷载试验研究,采用OpenSees软件对该组合柱进行了滞回性能数值分析,获取了组合柱的滞回曲线及抗震性能指标,并与试验结果进行了比较,验证了组合柱数值模型的合理性。在此基础上,对组合柱的滞回性能开展了参数影响分析。结果表明:再生骨料取代率从0增大到100%,组合柱的峰值荷载下降了7.78%,延性略有降低;提高再生混凝土强度、型钢强度及圆钢管强度,对于提升组合柱的承载力及刚度是有利的,但却使组合柱的脆性增大;随着轴压比的增大,组合柱的承载力呈现先上升后下降的趋势,而延性逐渐变差;型钢配钢率从5.54%增至9.99%,组合柱的峰值荷载提高了24.34%,但对于改善组合柱的延性不明显;增大钢管壁厚对组合柱的承载力和延性均是有利的。

圆钢管型钢再生混凝土组合柱水平承载力计算方法研究

通过对11个圆钢管型钢再生混凝土组合柱进行低周反复荷载试验,分析再生粗骨料取代率、型钢截面形式、轴压比、型钢配钢率及圆钢管壁厚参数对组合柱水平承载力的影响规律;观察了组合柱的破坏形态及特征,研究了圆钢管、型钢翼缘及腹板应变的发展规律,分析了组合柱的地震破坏特征。研究表明,在水平地震作用下组合柱发生典型的压弯塑性铰破坏。在此基础上,结合现有规范提出了基于叠加原理的圆钢管型钢再生混凝土组合柱水平承载力计算方法。计算结果表明,其水平承载力计算值与试验值吻合度较好,能较为准确地预测组合柱的水平承载力。

开槽侧板加强型连接梁柱节点子结构抗连续倒塌性能研究

为了优化侧板加强型节点的抗连续倒塌性能,提出了一种开槽侧板加强型梁柱连接节点形式。通过静力加载试验,得到了新型节点子结构的破坏模式、竖向抗力发展机制、应变分布、延性水平和动力承载力等。试验结果表明:钢梁翼缘在盖板附近首先开裂并向腹板外排螺栓中部延伸贯穿,导致竖向承载力快速下降为峰值荷载的20%左右。相比传统侧板加强型和圆弧扩盖板型梁柱节点,新型节点的峰值承载力分别提高了62.1%和19.6%,塑性弦转角分别提高了203.6%和25.8%。通过有限元分析得到了试件的断裂路径发展过程,进一步地通过参数化分析发现:扩大过焊孔构造对改善峰值后塑性弦转角及残余强度提升无明显作用;随着螺栓群远离钢梁翼缘起始断裂位置,最小残余强度比不断增大,但峰值后塑性弦转角呈先增大后减小的趋势;当螺栓群内移45mm时,峰值后塑性弦转角及最小残余强度比分别达到0.149rad和0.88,提高了38.2%和200.8%。

基于机器学习的CFST柱高温剩余强度系数预测方法

目的 为提高计算精度和速度,利用机器学习模型泛化数据,以预测CFST柱的高温剩余强度系数。方法 利用生成对抗网络将搜集到的110个试验结果泛化生成407组数据,据此训练机器学习模型,并使用试验结果评估其性能,以确定最优模型;然后使用生成数据输入建立的模型预测CFST柱高温剩余强度系数,并和现有计算方法进行对比。结果 建立的随机森林模型在性能度量上表现最好,拟合优度达到0.947 7,均方误差为0.001 8,精度为94.7%;预测结果误差在±10%内的数据为83%,在±20%内的数据为100%;剩余强度系数主要影响因素依次为温度、钢材屈服强度、混凝土抗压强度和横截面积,钢管厚度影响很小。结论 提出的预测方法优于现有计算方法,具有更快的计算速度、更小的结果误差以及更强的模型可解释性,该方法可为CFST柱抗火设计提供参考。

爆炸荷载下预制节段拼装双层钢管混凝土墩柱的动力响应数值模拟

为提升装配式公路桥梁的抗爆防护能力,提出了一种新型预制节段拼装双层钢管混凝土(PS-CFDST)组合墩柱.基于非线性显式动力分析程序LS-DYNA建立了新型PS-CFDST墩柱在爆炸荷载作用下动力响应分析的精细有限元模型,并通过已有试验结果验证了模型的准确性.对爆炸荷载作用下PS-CFDST墩柱的动力响应进行数值模拟分析,研究了PS-CFDST墩柱在爆炸荷载作用下的破坏过程、损伤机理和耗能机制.运用参数化分析方法,研究了爆炸距离、节段数量和预应力水平等关键参数对PS-CFDST墩柱动力响应的影响,并在此基础上提出了PS-CFDST墩柱的抗爆设计建议.结果表明:PS-CFDST墩柱除通过材料塑性损伤耗能之外,节段接缝界面滑移耗能机制对耗能贡献可达40%以上;增大墩柱可接近距离是提升墩柱抗爆安全性的有效手段,增大预应力有利于减小柱中最大水平位移和墩底剪切滑移,从而提升PS-CFDST墩柱的抗爆性能.

大高宽比矩形钢管混凝土柱压弯性能研究

为了研究大高宽比矩形钢管混凝土柱的压弯性能,对大高宽比钢管混凝土短柱进行偏压试验并结合有限元模拟补充了4组试件进行对比,包括不同偏心率、高宽比、钢管壁厚度、截面尺寸情况下柱性能的对比分析。最后参考常用的4本国内外规范进行柱承载力计算,对比并判断现有规范是否适用。结果表明:试件破坏模式均为长边鼓曲,当荷载小于极限承载力的80%时,横截面高度上的应变分布服从平截面假定;随着偏心率增大,柱延性提升,在偏心率超过0.205后,柱延性开始下降;随着壁厚增加,柱延性提升,在壁厚达到8 mm后,柱延性开始下降;随着高宽比提升,柱延性降低;随着截面尺寸增大,在壁厚不变的情况下,柱延性降低,在壁厚等比例增大时,柱延性变化不大;随着高宽比、截面尺寸、钢管壁厚度的增大,柱承载力提升;随着偏心率升高,柱承载力降低;参考规范JGJ 138—2016对大高宽比钢管混凝土柱偏压承载力的计算更为准确。