In South Saharan countries, 85% of the population uses biomass as a primary energy source. Cameroon presents one of the highest biomass energy and sawmills produce important sawdust resources which are not used and ar...In South Saharan countries, 85% of the population uses biomass as a primary energy source. Cameroon presents one of the highest biomass energy and sawmills produce important sawdust resources which are not used and are burnt in piles leading to significant air toxic emissions. Therefore, we have to valorize industrially these available sawdusts. This study focuses on the physicochemical and thermochemical analysis of Ayous, Sapelli and Tali sawdust. The proximate and ultimate analysis, particle size, structural composition, as well as heavy metal content and calorific value were determined. In addition, the thermogravimetric mass losses were also estimated. The results showed that high water contents (24% - 41%) were recorded in the raw sawdust, and the thermal treatment reduced these contents from 78% to values in the range of 4% - 9%. The values for ash and volatile matter content were respectively between 0.25% - 0.74% and 68% - 76%. The LHV is higher in Ayous (17.5 MJ/kg) and Sapelli (16.8 MJ/kg) than that of Tali (15.7 MJ/kg). The concentration of heavy metals is very low in each species. Extractives are more present in Tali (16.06%) than in the other sawdusts. Pyrolysis of sawdust shows the typical decomposition of hemicellulose (270˚C - 325˚C), cellulose (325˚C - 400˚C) and lignin (200˚C - 550˚C) with a maximum loss of 75% at 370˚C and the melting point is 320˚C. The results of the sawdust parameters determined in the paper can be valorized to reduce pollutants emissions by developing the efficiency and effectiveness of biomass energy processes and promoting the use of biomass as a sustainable alternative to traditional fossil fuels.展开更多
Several works have been based on the study of thermal variations in biomass to derive more valuable products such as fuels capable of replacing oil in the event of a crisis or activated carbon used as an adsorbent mat...Several works have been based on the study of thermal variations in biomass to derive more valuable products such as fuels capable of replacing oil in the event of a crisis or activated carbon used as an adsorbent material, widely used in industry for the elimination of unwanted materials, both in liquid and gaseous environments. A study of thermal parameters such as: heating speed, retention time, drying temperature, carbonization temperature, particle size, was carried out with the aim of determining the characteristic factors of the carbonization of Polyethylene terephthalate (PET), sawdust (SC) and sawdust/polyethylene terephthalate (CPS) mixture. The results of the immediate analysis revealed a very low level of ash in PET (0.013%) compared to the level of ash in sawdust (2.9%), as well as a high level of fixed carbon (82.960%), which suggests the presence of mineral oxides and a significant carbon matrix unlike PET, which indicates a very significant organic matrix (essentially made up of organic matter) with the absence of mineral oxides. The study of thermal parameters showed the water loss from Sawdust (SC) and the Sawdust/Polyethylene terephthalate (CPS) mixture, an increase with temperature, unlike that of PET whose variation is essentially zero. Without heat treatment, sawdust alone contains approximately 7% water. The optimal drying temperature for this study is 110˚C for a stay of 24 hours. It appears that the largest mass losses for the PET samples are between 87.19% and 96.05%, followed by that of the mixture, between 47.33% and 64.37%. And the lowest are observed, those of sawdust (from 24.02% to 62.6%). However, here we can say that the influence of the mass is not great, given the slight difference between the losses by temperature. The results of the study of the influence of grain size showed that the differences are insignificant, even if we vary the diameter of the grains from simple to triple. To better minimize physical constraints such as the intragranular diffusibility of the volatile matter and the homogeneity of the temperature in the grains, 75 μm particles are found to be optimal for our study. It can be noted when studying the heating rate that the mass loss at the end of the reaction is approximately the same depending on each precursor material. However, it has been demonstrated that the heating rate strongly influences the nature of the reaction products both for volatile materials and for the solid residue as well as on the kinetic parameters of the chemical reaction. Furthermore, the variation in apparent density shows a decrease as a function of the increase in the residence time of the materials in the reactor. As the carbonization time increases, the apparent density decreases. We note, for the lignocellulosic material, that the apparent density stabilizes after 60 minutes.展开更多
This study focuses on the extraction of cellulose nanocrystals (CNC), from microcrystalline cellulose (MCC), derived from Ayous sawdust. The process involves multiple steps and a large amount of chemical products. The...This study focuses on the extraction of cellulose nanocrystals (CNC), from microcrystalline cellulose (MCC), derived from Ayous sawdust. The process involves multiple steps and a large amount of chemical products. The objective of this research was to determine the effects of factors that impact the isolation process and to identify the optimal conditions for CNC isolation by using the response surface methodology. The factors that varied during the process were the quantity of MCC, the concentration of sulfuric acid, the hydrolysis time and temperature, and the ultrasonic treatment time. The response measured was the yield. The study found that with 5.80 g of microcrystalline cellulose, a sulfuric acid concentration of 63.50% (w/w), a hydrolysis time of 53 minutes, a hydrolysis temperature of 69˚C, and a sonication time of 19 minutes are the ideal conditions for isolation. The experimental yield achieved was (37.84 ± 0.99) %. The main factors influencing the process were the sulfuric acid concentration, hydrolysis time and temperature, with a significant influence (p < 0.05). Infrared characterization results showed that nanocrystals were indeed isolated. With a crystallinity of 35.23 and 79.74, respectively, for Ayous wood fiber and nanocrystalline cellulose were observed by X-ray diffraction, with the formation of type II cellulose, thermodynamically more stable than native cellulose type I.展开更多
文摘In South Saharan countries, 85% of the population uses biomass as a primary energy source. Cameroon presents one of the highest biomass energy and sawmills produce important sawdust resources which are not used and are burnt in piles leading to significant air toxic emissions. Therefore, we have to valorize industrially these available sawdusts. This study focuses on the physicochemical and thermochemical analysis of Ayous, Sapelli and Tali sawdust. The proximate and ultimate analysis, particle size, structural composition, as well as heavy metal content and calorific value were determined. In addition, the thermogravimetric mass losses were also estimated. The results showed that high water contents (24% - 41%) were recorded in the raw sawdust, and the thermal treatment reduced these contents from 78% to values in the range of 4% - 9%. The values for ash and volatile matter content were respectively between 0.25% - 0.74% and 68% - 76%. The LHV is higher in Ayous (17.5 MJ/kg) and Sapelli (16.8 MJ/kg) than that of Tali (15.7 MJ/kg). The concentration of heavy metals is very low in each species. Extractives are more present in Tali (16.06%) than in the other sawdusts. Pyrolysis of sawdust shows the typical decomposition of hemicellulose (270˚C - 325˚C), cellulose (325˚C - 400˚C) and lignin (200˚C - 550˚C) with a maximum loss of 75% at 370˚C and the melting point is 320˚C. The results of the sawdust parameters determined in the paper can be valorized to reduce pollutants emissions by developing the efficiency and effectiveness of biomass energy processes and promoting the use of biomass as a sustainable alternative to traditional fossil fuels.
文摘Several works have been based on the study of thermal variations in biomass to derive more valuable products such as fuels capable of replacing oil in the event of a crisis or activated carbon used as an adsorbent material, widely used in industry for the elimination of unwanted materials, both in liquid and gaseous environments. A study of thermal parameters such as: heating speed, retention time, drying temperature, carbonization temperature, particle size, was carried out with the aim of determining the characteristic factors of the carbonization of Polyethylene terephthalate (PET), sawdust (SC) and sawdust/polyethylene terephthalate (CPS) mixture. The results of the immediate analysis revealed a very low level of ash in PET (0.013%) compared to the level of ash in sawdust (2.9%), as well as a high level of fixed carbon (82.960%), which suggests the presence of mineral oxides and a significant carbon matrix unlike PET, which indicates a very significant organic matrix (essentially made up of organic matter) with the absence of mineral oxides. The study of thermal parameters showed the water loss from Sawdust (SC) and the Sawdust/Polyethylene terephthalate (CPS) mixture, an increase with temperature, unlike that of PET whose variation is essentially zero. Without heat treatment, sawdust alone contains approximately 7% water. The optimal drying temperature for this study is 110˚C for a stay of 24 hours. It appears that the largest mass losses for the PET samples are between 87.19% and 96.05%, followed by that of the mixture, between 47.33% and 64.37%. And the lowest are observed, those of sawdust (from 24.02% to 62.6%). However, here we can say that the influence of the mass is not great, given the slight difference between the losses by temperature. The results of the study of the influence of grain size showed that the differences are insignificant, even if we vary the diameter of the grains from simple to triple. To better minimize physical constraints such as the intragranular diffusibility of the volatile matter and the homogeneity of the temperature in the grains, 75 μm particles are found to be optimal for our study. It can be noted when studying the heating rate that the mass loss at the end of the reaction is approximately the same depending on each precursor material. However, it has been demonstrated that the heating rate strongly influences the nature of the reaction products both for volatile materials and for the solid residue as well as on the kinetic parameters of the chemical reaction. Furthermore, the variation in apparent density shows a decrease as a function of the increase in the residence time of the materials in the reactor. As the carbonization time increases, the apparent density decreases. We note, for the lignocellulosic material, that the apparent density stabilizes after 60 minutes.
文摘This study focuses on the extraction of cellulose nanocrystals (CNC), from microcrystalline cellulose (MCC), derived from Ayous sawdust. The process involves multiple steps and a large amount of chemical products. The objective of this research was to determine the effects of factors that impact the isolation process and to identify the optimal conditions for CNC isolation by using the response surface methodology. The factors that varied during the process were the quantity of MCC, the concentration of sulfuric acid, the hydrolysis time and temperature, and the ultrasonic treatment time. The response measured was the yield. The study found that with 5.80 g of microcrystalline cellulose, a sulfuric acid concentration of 63.50% (w/w), a hydrolysis time of 53 minutes, a hydrolysis temperature of 69˚C, and a sonication time of 19 minutes are the ideal conditions for isolation. The experimental yield achieved was (37.84 ± 0.99) %. The main factors influencing the process were the sulfuric acid concentration, hydrolysis time and temperature, with a significant influence (p < 0.05). Infrared characterization results showed that nanocrystals were indeed isolated. With a crystallinity of 35.23 and 79.74, respectively, for Ayous wood fiber and nanocrystalline cellulose were observed by X-ray diffraction, with the formation of type II cellulose, thermodynamically more stable than native cellulose type I.
