In this paper, we first propose a metamaterial structure by etching the same two interdigital fingers on the upper ground of quarter mode substrate integrated waveguide（QMSIW）. The simulated results show that the pr...In this paper, we first propose a metamaterial structure by etching the same two interdigital fingers on the upper ground of quarter mode substrate integrated waveguide（QMSIW）. The simulated results show that the proposed QMSIWbased metamaterial has a continuous phase constant changing from negative to positive values within its passband. A periodic leaky-wave antenna（LWA）, which consists of 11 QMSIW-based metamaterial unit cells, is designed, fabricated,and measured. The measured results show that the fabricated antenna achieves a continuous beam scanning property from backward-43° to forward ＋32° over an operating frequencyrange of 8.9 GHz–11.8 GHz with return loss better than 10 d B.The measured antenna gain keeps consistent with the variation of less than 2 d B over the operating frequency range with a maximum gain of 12 d B. Besides, the measured and simulated results are in good agreement with each other, indicating the significance and effectiveness of this method.展开更多
Background: The stem curve of standing trees is an essential parameter for accurate estimation of stem volume.This study aims to directly quantify the occlusions within the single-scan terrestrial laser scanning(TLS) ...Background: The stem curve of standing trees is an essential parameter for accurate estimation of stem volume.This study aims to directly quantify the occlusions within the single-scan terrestrial laser scanning(TLS) data,evaluate its correlation with the accuracy of the retrieved stem curves, and subsequently, to assess the capacity of single-scan TLS to estimate stem curves.Methods: We proposed an index, occlusion rate, to quantify the occlusion level in TLS data. We then analyzed three influencing factors for the occlusion rate: the percentage of basal area near the scanning center, the scanning distance and the source of occlusions. Finally, we evaluated the effects of occlusions on stem curve estimates from single-scan TLS data.Results: The results showed that the correlations between the occlusion rate and the stem curve estimation accuracies were strong(r = 0.60–0.83), so was the correlations between the occlusion rate and its influencing factors(r = 0.84–0.99). It also showed that the occlusions from tree stems were the main factor of the low detection rate of stems, while the non-stem components mainly influenced the completeness of the retrieved stem curves.Conclusions: Our study demonstrates that the occlusions significantly affect the accuracy of stem curve retrieval from the single-scan TLS data in a typical-size(32 m × 32 m) forest plot. However, the single-scan mode has the capacity to accurately estimate the stem curve in a small forest plot(< 10 m × 10 m) or a plot with a lower occlusion rate, such as less than 35% in our tested datasets. The findings from this study are useful for guiding the practice of retrieving forest parameters using single-scan TLS data.展开更多
In order to use electron beam as a movable welding heat source and whose energy distribution along its moving trace can be controlled, a method of electron beam scanning track and scanning mode control was put forward...In order to use electron beam as a movable welding heat source and whose energy distribution along its moving trace can be controlled, a method of electron beam scanning track and scanning mode control was put forward. Based on it, the electron beam scanning track and scanning mode can be edited at will according to actual requirements, and the energy input of each point of the scanning track can be controlled. In addition, the scanning frequency and points control, real time adjusting of the scanning track etc. were explained. This method can be used in electron beam brazing, surface modification, surface heat treatment etc.展开更多
Doppler centroid frequency is an essential parameter in the imaging processing of the Scanning mode Synthetic Aperture Radar (ScanSAR). Inaccurate Doppler centroid frequency will result in ghost images in imaging resu...Doppler centroid frequency is an essential parameter in the imaging processing of the Scanning mode Synthetic Aperture Radar (ScanSAR). Inaccurate Doppler centroid frequency will result in ghost images in imaging result. In this letter, the principle and algorithms of Doppler centroid frequency estimation are introduced. Then the echo data of ScanSAR system is analyzed. Based on the algorithms of energy balancing and correlation Doppler estimator in the estimation of Doppler centroid frequency in strip mode SAR, an improved method for Doppler centroid frequency estimation in ScanSAR is proposed. The method has improved the accuracy of Doppler centroid frequency estimation in ScanSAR by zero padding between burst data. Finally, the proposed method is validated with the processing of ENVIronment SATellite Advanced Synthetic Aperture Radar (ENVISAT ASAR) wide swath raw data.展开更多
Based on the results of conventional triaxial compression tests and triaxial compression creep tests on Xiangjiaba sandstone,the failure modes in short-term tests and creep tests,fractography of sandstone after creep ...Based on the results of conventional triaxial compression tests and triaxial compression creep tests on Xiangjiaba sandstone,the failure modes in short-term tests and creep tests,fractography of sandstone after creep failure,short-term and creep failure criterion are analyzed.In the short-term tests and creep tests,the sandstone samples fail in a mix mode consisting of shear failure in a single main plane and tensile failure.Confining pressure can restrict brittle failure and enhance the ductility of sandstone.In the creep tests,brittle fracture is reduced and plastic deformation can fully be developed compared to the condition of short-term tests.And the shear fracture surfaces are flat and they are covered by small particles as a result of friction.When confining pressure increases,particle size decreases while the degree of friction on shear plane increases.On the tensile failure plane,the tensile trace and direction of tearing could be clearly observed.There are obvious tearing steps on the tensile failure plane and tearing laminated structure on the front edge of tearing fracture.The same criterion can be used for the short-term and creep behavior,and the fitting effect using the MOGI criterion is better than the DRUCKER PRAGER criterion.The cohesion and friction angle calculated by the MOGI criterion are in good accordance with those calculated by the MOHR COULOMB criterion.展开更多
基金Project supported by the National Natural Science Foundation of China(Grant No.61372034)
文摘In this paper, we first propose a metamaterial structure by etching the same two interdigital fingers on the upper ground of quarter mode substrate integrated waveguide（QMSIW）. The simulated results show that the proposed QMSIWbased metamaterial has a continuous phase constant changing from negative to positive values within its passband. A periodic leaky-wave antenna（LWA）, which consists of 11 QMSIW-based metamaterial unit cells, is designed, fabricated,and measured. The measured results show that the fabricated antenna achieves a continuous beam scanning property from backward-43° to forward ＋32° over an operating frequencyrange of 8.9 GHz–11.8 GHz with return loss better than 10 d B.The measured antenna gain keeps consistent with the variation of less than 2 d B over the operating frequency range with a maximum gain of 12 d B. Besides, the measured and simulated results are in good agreement with each other, indicating the significance and effectiveness of this method.
基金supported by the National Natural Science Foundation of China(Grant Nos.41671414,41971380,41331171 and 41171265)the National Key Research and Development Program of China(No.2016YFB0501404)
文摘Background: The stem curve of standing trees is an essential parameter for accurate estimation of stem volume.This study aims to directly quantify the occlusions within the single-scan terrestrial laser scanning(TLS) data,evaluate its correlation with the accuracy of the retrieved stem curves, and subsequently, to assess the capacity of single-scan TLS to estimate stem curves.Methods: We proposed an index, occlusion rate, to quantify the occlusion level in TLS data. We then analyzed three influencing factors for the occlusion rate: the percentage of basal area near the scanning center, the scanning distance and the source of occlusions. Finally, we evaluated the effects of occlusions on stem curve estimates from single-scan TLS data.Results: The results showed that the correlations between the occlusion rate and the stem curve estimation accuracies were strong(r = 0.60–0.83), so was the correlations between the occlusion rate and its influencing factors(r = 0.84–0.99). It also showed that the occlusions from tree stems were the main factor of the low detection rate of stems, while the non-stem components mainly influenced the completeness of the retrieved stem curves.Conclusions: Our study demonstrates that the occlusions significantly affect the accuracy of stem curve retrieval from the single-scan TLS data in a typical-size(32 m × 32 m) forest plot. However, the single-scan mode has the capacity to accurately estimate the stem curve in a small forest plot(< 10 m × 10 m) or a plot with a lower occlusion rate, such as less than 35% in our tested datasets. The findings from this study are useful for guiding the practice of retrieving forest parameters using single-scan TLS data.
基金Commission of Science Technology and In-dustry for National Defense Project:Electron beam brazing tech-nology research ( 4 13 183 2 3 )
文摘In order to use electron beam as a movable welding heat source and whose energy distribution along its moving trace can be controlled, a method of electron beam scanning track and scanning mode control was put forward. Based on it, the electron beam scanning track and scanning mode can be edited at will according to actual requirements, and the energy input of each point of the scanning track can be controlled. In addition, the scanning frequency and points control, real time adjusting of the scanning track etc. were explained. This method can be used in electron beam brazing, surface modification, surface heat treatment etc.
文摘Doppler centroid frequency is an essential parameter in the imaging processing of the Scanning mode Synthetic Aperture Radar (ScanSAR). Inaccurate Doppler centroid frequency will result in ghost images in imaging result. In this letter, the principle and algorithms of Doppler centroid frequency estimation are introduced. Then the echo data of ScanSAR system is analyzed. Based on the algorithms of energy balancing and correlation Doppler estimator in the estimation of Doppler centroid frequency in strip mode SAR, an improved method for Doppler centroid frequency estimation in ScanSAR is proposed. The method has improved the accuracy of Doppler centroid frequency estimation in ScanSAR by zero padding between burst data. Finally, the proposed method is validated with the processing of ENVIronment SATellite Advanced Synthetic Aperture Radar (ENVISAT ASAR) wide swath raw data.
基金Project(2011CB013504)supported by National Basic Research Program of ChinaProjects(51109069,11172090)supported by the National Natural Science Foundation of China+1 种基金Project(2009B14014)supported by the Fundamental Research Funds for the Central Universities of ChinaProject Financially supported by the Program for Changjiang Scholars and lnnovative Research Team in University,China
文摘Based on the results of conventional triaxial compression tests and triaxial compression creep tests on Xiangjiaba sandstone,the failure modes in short-term tests and creep tests,fractography of sandstone after creep failure,short-term and creep failure criterion are analyzed.In the short-term tests and creep tests,the sandstone samples fail in a mix mode consisting of shear failure in a single main plane and tensile failure.Confining pressure can restrict brittle failure and enhance the ductility of sandstone.In the creep tests,brittle fracture is reduced and plastic deformation can fully be developed compared to the condition of short-term tests.And the shear fracture surfaces are flat and they are covered by small particles as a result of friction.When confining pressure increases,particle size decreases while the degree of friction on shear plane increases.On the tensile failure plane,the tensile trace and direction of tearing could be clearly observed.There are obvious tearing steps on the tensile failure plane and tearing laminated structure on the front edge of tearing fracture.The same criterion can be used for the short-term and creep behavior,and the fitting effect using the MOGI criterion is better than the DRUCKER PRAGER criterion.The cohesion and friction angle calculated by the MOGI criterion are in good accordance with those calculated by the MOHR COULOMB criterion.
