In this paper, a flexible high-precision calibration method suitable for industrial field was proposed. The complexity of the coordinate transformation was simplified by choosing the camera coordinate system as the un...In this paper, a flexible high-precision calibration method suitable for industrial field was proposed. The complexity of the coordinate transformation was simplified by choosing the camera coordinate system as the unified reference coordinate system. A flexible planar calibration pattern was introduced to the calibration process, which can be arbitrarily placed and from which the known feature points can be extracted to construct other unknown feature points. With the known intrinsic parameters, the laser projector plane equation was fitted by the multi-noncollinear points, which were acquired through the principle of triangulation and the projective invariance of cross ratio. With this method, the strict alignment and multiple times of coordinate transformation can be avoided. Experimental results showed that the arithmetic mean of the root mean square(RMS) error of distance was 0.000 7 mm.展开更多
Based on previously reported work, we propose a new method for calibrating image plate(IP) scanners, offering greater flexibility and convenience, which can be extended to the calibration tasks of various scanner mode...Based on previously reported work, we propose a new method for calibrating image plate(IP) scanners, offering greater flexibility and convenience, which can be extended to the calibration tasks of various scanner models. This method was applied to calibrate the sensitivity of a GE Typhoon FLA 7000 scanner. Additionally, we performed a calibration of the spontaneous signal attenuation behavior for BAS-MS, BAS-SR, and BAS-TR type IPs under the 20±1℃ environmental conditions, and observed significant signal carrier diffusion behavior in BAS-MS IP. The calibration results lay a foundation for further research on the interaction between ultra-short, ultra-intense lasers and matter.展开更多
In this study, a three-dimensional (3D) in-situ laser machining system integrating laser measurement and machining was built using a 3D galvanometer scanner equipped with a side-axis industrial camera. A line structur...In this study, a three-dimensional (3D) in-situ laser machining system integrating laser measurement and machining was built using a 3D galvanometer scanner equipped with a side-axis industrial camera. A line structured light measurement model based on a galvanometer scanner was proposed to obtain the 3D information of the workpiece. A height calibration method was proposed to further ensure measurement accuracy, so as to achieve accurate laser focusing. In-situ machining software was developed to realize time-saving and labor-saving 3D laser processing. The feasibility and practicability of this in-situ laser machining system were verified using specific cases. In comparison with the conventional line structured light measurement method, the proposed methods do not require light plane calibration, and do not need additional motion axes for 3D reconstruction;thus they provide technical and cost advantages. The insitu laser machining system realizes a simple operation process by integrating measurement and machining,which greatly reduces labor and time costs.展开更多
Aluminum welding using a hybrid system with a laser and scanner welding head was performed under various welding conditions to verify the feasibility of applying an aluminum alloy to a car body.The experimental materi...Aluminum welding using a hybrid system with a laser and scanner welding head was performed under various welding conditions to verify the feasibility of applying an aluminum alloy to a car body.The experimental material was 5J32 aluminum alloy,and the laser power,welding speed,and laser incidence angle were used as the control variables.The weld bead shape and the tensile shear strength were evaluated in order to understand the aluminum lap joint weld characteristics.Analysis of variance (ANOVA) was conducted to identify the effect of the process variables on the tensile shear strength.Tensile strength estimation models using three different regression models were also suggested.The input variables were the laser power,welding speed,and laser incidence angle,and the output was the tensile shear strength.Among the models,the second-order polynomial estimation model had the best estimation performance,and the average error rate of this model was 0.058.展开更多
A new wide-range fast readout system capable of adaptive identification is designed for wire scanners,which are used to measure beam profiles and emittance.This system is capable of handling varying current signals wi...A new wide-range fast readout system capable of adaptive identification is designed for wire scanners,which are used to measure beam profiles and emittance.This system is capable of handling varying current signals with Gaussian distributions and current pulses up to 1000 counts/s, as well as an input current range of 1 n A–1 m A. When tested, the resolution was found to exceed 3.68% for full scale, the nonlinearity was found to be less than 0.11%, and the measurement sensibility was found to be less than 5 p A. We believe that the system will play a crucial role in improving the measurement accuracy of beam diagnosis and the efficiency of accelerator operation,as well as decreasing the time required for beam tuning.This system was applied to the beam diagnosis of an injector II prototype for an accelerator-driven subcritical system and produced excellent measurement results. A description of the adaptive fast readout system for wire scanners is presented in this paper.展开更多
This paper deals with the scanner exterior calibration algorithm when the scanner is arranged by the robot and the object scanned is fixed on a rotate device in the Robot Remanufacturing System. The method of calibrat...This paper deals with the scanner exterior calibration algorithm when the scanner is arranged by the robot and the object scanned is fixed on a rotate device in the Robot Remanufacturing System. The method of calibrating the relationship between the scanner coordinate and the robot Tool0, such as the rotation, Rx, Ry, Rz, and the transformation ,Y, Z is studied. The data of Tool0 can be directly obtained from the relationship with the robot base-coordinate. So, the coordinate relationship between the scanner coordinate and the robot base coordinate can be easily gotten. This paper explains the basic algorithm theory, computing method, data collecting process and the resulted data in detail. The calibration algorithm is deduced under the orthogonal coordinate.展开更多
The development of measurement geometry for medical X-ray computed tomography （CT） scanners was carried out from the first to the fourth-generation. This concept has also been applied for imaging of industrial proce...The development of measurement geometry for medical X-ray computed tomography （CT） scanners was carried out from the first to the fourth-generation. This concept has also been applied for imaging of industrial processes such as pipe flows or for improving design, operation, optimization and troubleshooting. Nowadays, gamma CT permits to visualize failure equipment points in three-dimensional analysis and in sections of chemical and petrochemical industries. The aim of this work is the development of the mechanical system on a third-generation industrial CT scanner to analyze laboratorial process columns which perform highly efficient separation, turning the ^6oCo, ^75Se, ^137Cs and/or ^192Ir sealed gamma-ray source（s） and the NaI（Tl） multidetector array. It also has a translation movement along the column axis to obtain as many slices of the process flow as needed. The mechanical assembly for this third-generation industrial CT scanner is comprised by strength and rigidity structural frame in stainless and carbon steels, rotating table, source shield and collimator with pneumatic exposure system, spur gear system, translator, rotary stage, drives and stepper motors. The use of suitable spur gears has given a good repeatability and high accuracy in the degree of veracity. The data acquisition boards, mechanical control interfaces, software for movement control and image reconstruction were specially development. A multiphase phantom capable to be setting with solid, liquid and gas was testing. The scanner was setting for 90 views and 19 projections for each detector totalizing 11,970 projections. Experiments to determine the linear attenuation coefficients of the phantom were carried out which applied the Lambert-Beer principle. Results showed that it was possible to distinguish between the phases even the polymethylmethacrylate and the water have very similar density and linear attenuation coefficients. It was established that the newly developed third-generation fan-beam arrangement gamma scanner unit has a good spatial resolution acceptable given the size of the used phantom in this study. The tomografic reconstruction algorithm in used 60 ~ 60 pixels images was the Alternative Minimization （AM） technique and was implemented in MATLAB and VB platforms. The mechanical system presented a good performance in terms of strength, rigidity, accuracy and repeatability with great potential to be used for education or program which dedicated to training chemical and petrochemical industry professionals and for industrial process optimization in Brazil.展开更多
Novel electron states stabilized by Coulomb interactions attract tremendous interests in condensed matter physics.These states are studied by corresponding phase transitions occurring at extreme conditions such as mK ...Novel electron states stabilized by Coulomb interactions attract tremendous interests in condensed matter physics.These states are studied by corresponding phase transitions occurring at extreme conditions such as mK temperatures and high magnetic field.In this work,we introduce a magneto-optical Kerr effect measurement system to comprehensively explore these phases in addition to conventional transport measurement.This system,composed of an all-fiber zero-loop Sagnac interferometer and in situ piezo-scanner inside a dilution refrigerator,operates below 100 m K,with a maximum field of 12 Tesla and has a resolution as small as 0.2μrad.As a demonstration,we investigate TbMn_(6)Sn_(6),where the manganese atoms form Kagome lattice that hosts topological non-trivial Dirac cones.We observed two types of Kerr signals,stemming from its fully polarized ferromagnetic ground state and positive charged carriers within the Dirac-like dispersion.展开更多
Recently,a study on a 0.05 T,low-cost,low-power,and computing-driven shielding-free ultra-low-field(ULF)magnetic resonance imaging(MRI)scannerwas published.This work enhances the image quality of MRI and reduces the s...Recently,a study on a 0.05 T,low-cost,low-power,and computing-driven shielding-free ultra-low-field(ULF)magnetic resonance imaging(MRI)scannerwas published.This work enhances the image quality of MRI and reduces the scanning time based on deep learning methods,which is of great significance to enhancing the popularization and availability of MRI[1](https://www.science.org/doi/abs/10.1126/science.adm7168).展开更多
To expand scanning area and attack range without changing the inner structure of intelligent warhead, a new arrangement mode of the scanner for intelligent mine is proposed. The required coordinate systems are es...To expand scanning area and attack range without changing the inner structure of intelligent warhead, a new arrangement mode of the scanner for intelligent mine is proposed. The required coordinate systems are established firstly on the basis of advanced dynamics principle. and the exterior ballistics equations are deduced. Then the equations of scanning trails are established by the method of space analytic geometry. To get the scanning trails. the differential equations are transformed into discrete simulation model using the algorithm of fourth order Runge-Kutta and then are simulated using Matlab. Compared with the scanning trails obtained by the traditional layout of scanner, the scanning trails obtained by the proposed layout of scanner has larger horizontal range of scanning circle and bigger trarget acquisition probability. Therefore, the new arrangement mode of the scanner for intelligent mine can increase attack range.展开更多
基金Supported by the National Natural Science Foundation of China(No.51105273)
文摘In this paper, a flexible high-precision calibration method suitable for industrial field was proposed. The complexity of the coordinate transformation was simplified by choosing the camera coordinate system as the unified reference coordinate system. A flexible planar calibration pattern was introduced to the calibration process, which can be arbitrarily placed and from which the known feature points can be extracted to construct other unknown feature points. With the known intrinsic parameters, the laser projector plane equation was fitted by the multi-noncollinear points, which were acquired through the principle of triangulation and the projective invariance of cross ratio. With this method, the strict alignment and multiple times of coordinate transformation can be avoided. Experimental results showed that the arithmetic mean of the root mean square(RMS) error of distance was 0.000 7 mm.
基金supported by the Nuclear Industry Academician Fund, the National Natural Science Foundation of China (Grant No. 1220051312)Young Talents Fund of China National Nuclear Corporation (Grant No. FY212406000901)。
文摘Based on previously reported work, we propose a new method for calibrating image plate(IP) scanners, offering greater flexibility and convenience, which can be extended to the calibration tasks of various scanner models. This method was applied to calibrate the sensitivity of a GE Typhoon FLA 7000 scanner. Additionally, we performed a calibration of the spontaneous signal attenuation behavior for BAS-MS, BAS-SR, and BAS-TR type IPs under the 20±1℃ environmental conditions, and observed significant signal carrier diffusion behavior in BAS-MS IP. The calibration results lay a foundation for further research on the interaction between ultra-short, ultra-intense lasers and matter.
文摘In this study, a three-dimensional (3D) in-situ laser machining system integrating laser measurement and machining was built using a 3D galvanometer scanner equipped with a side-axis industrial camera. A line structured light measurement model based on a galvanometer scanner was proposed to obtain the 3D information of the workpiece. A height calibration method was proposed to further ensure measurement accuracy, so as to achieve accurate laser focusing. In-situ machining software was developed to realize time-saving and labor-saving 3D laser processing. The feasibility and practicability of this in-situ laser machining system were verified using specific cases. In comparison with the conventional line structured light measurement method, the proposed methods do not require light plane calibration, and do not need additional motion axes for 3D reconstruction;thus they provide technical and cost advantages. The insitu laser machining system realizes a simple operation process by integrating measurement and machining,which greatly reduces labor and time costs.
基金Project(KRF-2010-0003259)supported by the Korea Research Foundation Grant funded by the Korean Government
文摘Aluminum welding using a hybrid system with a laser and scanner welding head was performed under various welding conditions to verify the feasibility of applying an aluminum alloy to a car body.The experimental material was 5J32 aluminum alloy,and the laser power,welding speed,and laser incidence angle were used as the control variables.The weld bead shape and the tensile shear strength were evaluated in order to understand the aluminum lap joint weld characteristics.Analysis of variance (ANOVA) was conducted to identify the effect of the process variables on the tensile shear strength.Tensile strength estimation models using three different regression models were also suggested.The input variables were the laser power,welding speed,and laser incidence angle,and the output was the tensile shear strength.Among the models,the second-order polynomial estimation model had the best estimation performance,and the average error rate of this model was 0.058.
基金supported by the National Natural Science Foundation of China(Nos.11475233,11705257,and 11775285)
文摘A new wide-range fast readout system capable of adaptive identification is designed for wire scanners,which are used to measure beam profiles and emittance.This system is capable of handling varying current signals with Gaussian distributions and current pulses up to 1000 counts/s, as well as an input current range of 1 n A–1 m A. When tested, the resolution was found to exceed 3.68% for full scale, the nonlinearity was found to be less than 0.11%, and the measurement sensibility was found to be less than 5 p A. We believe that the system will play a crucial role in improving the measurement accuracy of beam diagnosis and the efficiency of accelerator operation,as well as decreasing the time required for beam tuning.This system was applied to the beam diagnosis of an injector II prototype for an accelerator-driven subcritical system and produced excellent measurement results. A description of the adaptive fast readout system for wire scanners is presented in this paper.
文摘This paper deals with the scanner exterior calibration algorithm when the scanner is arranged by the robot and the object scanned is fixed on a rotate device in the Robot Remanufacturing System. The method of calibrating the relationship between the scanner coordinate and the robot Tool0, such as the rotation, Rx, Ry, Rz, and the transformation ,Y, Z is studied. The data of Tool0 can be directly obtained from the relationship with the robot base-coordinate. So, the coordinate relationship between the scanner coordinate and the robot base coordinate can be easily gotten. This paper explains the basic algorithm theory, computing method, data collecting process and the resulted data in detail. The calibration algorithm is deduced under the orthogonal coordinate.
文摘The development of measurement geometry for medical X-ray computed tomography （CT） scanners was carried out from the first to the fourth-generation. This concept has also been applied for imaging of industrial processes such as pipe flows or for improving design, operation, optimization and troubleshooting. Nowadays, gamma CT permits to visualize failure equipment points in three-dimensional analysis and in sections of chemical and petrochemical industries. The aim of this work is the development of the mechanical system on a third-generation industrial CT scanner to analyze laboratorial process columns which perform highly efficient separation, turning the ^6oCo, ^75Se, ^137Cs and/or ^192Ir sealed gamma-ray source（s） and the NaI（Tl） multidetector array. It also has a translation movement along the column axis to obtain as many slices of the process flow as needed. The mechanical assembly for this third-generation industrial CT scanner is comprised by strength and rigidity structural frame in stainless and carbon steels, rotating table, source shield and collimator with pneumatic exposure system, spur gear system, translator, rotary stage, drives and stepper motors. The use of suitable spur gears has given a good repeatability and high accuracy in the degree of veracity. The data acquisition boards, mechanical control interfaces, software for movement control and image reconstruction were specially development. A multiphase phantom capable to be setting with solid, liquid and gas was testing. The scanner was setting for 90 views and 19 projections for each detector totalizing 11,970 projections. Experiments to determine the linear attenuation coefficients of the phantom were carried out which applied the Lambert-Beer principle. Results showed that it was possible to distinguish between the phases even the polymethylmethacrylate and the water have very similar density and linear attenuation coefficients. It was established that the newly developed third-generation fan-beam arrangement gamma scanner unit has a good spatial resolution acceptable given the size of the used phantom in this study. The tomografic reconstruction algorithm in used 60 ~ 60 pixels images was the Alternative Minimization （AM） technique and was implemented in MATLAB and VB platforms. The mechanical system presented a good performance in terms of strength, rigidity, accuracy and repeatability with great potential to be used for education or program which dedicated to training chemical and petrochemical industry professionals and for industrial process optimization in Brazil.
基金supported by the National Key Research and Development Program of China(Grant Nos.2021YFA1401900,2019YFA0308403,and 2018YFA0305604)the Innovation Program for Quantum Science and Technology(Grant Nos.2021ZD0302602 and 2021ZD0302403)+1 种基金the National Natural Science Foundation of China(Grant Nos.92065104,12074010,and 11888101)Capacity Building for Sci-Tech Innovation-Fundamental Scientific Research Funds(Grant Nos.20530290057 and KM202010028014)。
文摘Novel electron states stabilized by Coulomb interactions attract tremendous interests in condensed matter physics.These states are studied by corresponding phase transitions occurring at extreme conditions such as mK temperatures and high magnetic field.In this work,we introduce a magneto-optical Kerr effect measurement system to comprehensively explore these phases in addition to conventional transport measurement.This system,composed of an all-fiber zero-loop Sagnac interferometer and in situ piezo-scanner inside a dilution refrigerator,operates below 100 m K,with a maximum field of 12 Tesla and has a resolution as small as 0.2μrad.As a demonstration,we investigate TbMn_(6)Sn_(6),where the manganese atoms form Kagome lattice that hosts topological non-trivial Dirac cones.We observed two types of Kerr signals,stemming from its fully polarized ferromagnetic ground state and positive charged carriers within the Dirac-like dispersion.
文摘Recently,a study on a 0.05 T,low-cost,low-power,and computing-driven shielding-free ultra-low-field(ULF)magnetic resonance imaging(MRI)scannerwas published.This work enhances the image quality of MRI and reduces the scanning time based on deep learning methods,which is of great significance to enhancing the popularization and availability of MRI[1](https://www.science.org/doi/abs/10.1126/science.adm7168).
文摘To expand scanning area and attack range without changing the inner structure of intelligent warhead, a new arrangement mode of the scanner for intelligent mine is proposed. The required coordinate systems are established firstly on the basis of advanced dynamics principle. and the exterior ballistics equations are deduced. Then the equations of scanning trails are established by the method of space analytic geometry. To get the scanning trails. the differential equations are transformed into discrete simulation model using the algorithm of fourth order Runge-Kutta and then are simulated using Matlab. Compared with the scanning trails obtained by the traditional layout of scanner, the scanning trails obtained by the proposed layout of scanner has larger horizontal range of scanning circle and bigger trarget acquisition probability. Therefore, the new arrangement mode of the scanner for intelligent mine can increase attack range.
