This paper illuminates the preparation of grating-like polystyrene latex monolayer structure, which can minimize the effects of the size deviation of spheres and the defect transfer on the accuracy as calibration samp...This paper illuminates the preparation of grating-like polystyrene latex monolayer structure, which can minimize the effects of the size deviation of spheres and the defect transfer on the accuracy as calibration samples for micro-scopes. The latex films are grown on freshly cleaved mica substrates by vertical deposition method. The concentration dependence of the structure and the topography of latex films is characterized by optical microscope, ultraviolet- visible transmission spectrum and scanning probe microscope. The origination of such a grating-like structure is also discussed.展开更多
Scanning Probe Microscopes (SPMs) observe specimen surfaces with probes by detecting the physical amount of a material between the cantilever and the surface. SPMs have a high resolution and can measure mechanical cha...Scanning Probe Microscopes (SPMs) observe specimen surfaces with probes by detecting the physical amount of a material between the cantilever and the surface. SPMs have a high resolution and can measure mechanical characteristics such as stiffness, adsorptive properties, and viscoelasticity. These features make it easy to identify the surface structure of complex materials;therefore, the use of SPMs has increased in recent years. Wood cell walls are primarily composed of cellulose, hemicellulose, and lignin. It is believed that hemicellulose and lignin surround the cellulose framework;however, their detailed formation remains unknown. Therefore, we observed wood cell walls via scanning probe microscopy to try to reveal the formation of the cellulose framework. We determined that the size of the cellulose microfibril bundle and hemicellulose lignin module composite was 18.48 nm based on topography and that the size of the cellulose microfibril bundle was 15.33 nm based on phase images. In the viscoelasticity image, we found that the viscoelasticities of each cell wall of the same cell were not the same. This is because the cellulose microfibrils in each cell wall lean in different directions. The angle between the leaning of the cellulose microfibril and the cantilever affects the viscoelasticity measurement.展开更多
We present the design and performance of a home-built scanning tunneling microscope （STM）, which is compact （66 mm tall and 25 mm in diameter）, yet equipped with a 3D atomic precision piezoelectric motor in which ...We present the design and performance of a home-built scanning tunneling microscope （STM）, which is compact （66 mm tall and 25 mm in diameter）, yet equipped with a 3D atomic precision piezoelectric motor in which the Z coarse approach relies on a high simplic-ity friction-type walker （of our own invention） driven by an axially cut piezoelectric tube. The walker is vertically inserted in a piezoelectric scanner tube （PST） with its brim laying at on the PST end as the inertial slider （driven by the PST） for the XZ （sample plane） motion. The STM is designed to be capable of searching rare microscopic targets （defects, dopants, boundaries, nano-devices, etc.） in a macroscopic sample area （square millimeters） under extreme conditions （low temperatures, strong magnetic elds, etc.） in which it ts. It gives good atomic resolution images after scanning a highly oriented pyrolytic graphite sample in air at room temperature.展开更多
The influence of vibration is already one of main obstacles for improving the nano measuring accuracy.The techniques of anti-vibration,vibration isolation and vibration compensation become an important branch in nano ...The influence of vibration is already one of main obstacles for improving the nano measuring accuracy.The techniques of anti-vibration,vibration isolation and vibration compensation become an important branch in nano measuring field.Starting with the research of sensitivity to vibration of scanning tunneling microscope(STM),the theory,techniques and realization methods of nano vibration sensor based on tunnel effect are initially investigated,followed by developing the experimental devices.The experiments of the vibration detection and vibration compensation are carried out.The experimental results show that vibration sensor based on tunnel effect is characterized by high sensitivity,good frequency characteristic and the same vibratory response characteristic consistent with STM.展开更多
An experimental study on cutting amorphous alloy at nanometer scale is conducted by applying the principle and technology of scanning probe microscope(SPM) It is revealed from the experiments that cutting inside SPM...An experimental study on cutting amorphous alloy at nanometer scale is conducted by applying the principle and technology of scanning probe microscope(SPM) It is revealed from the experiments that cutting inside SPM is an excellent and direct way to research the material removal process at small size Based on the experimental results,the chip formation mechanism for the cutting of amorphous alloy is discussed It is found that the deformation along the direction of chip flow occurs ahead of the appearance of localized shear,and a simplified geometrical model is proposed to illustrate the deformation.展开更多
The surface of a compact disk is analyzed by using SPM and the quantitative micromorphology analysissoftware SPMIAS developed by the author. Images at the same position but with different scanning ranges areobtained ...The surface of a compact disk is analyzed by using SPM and the quantitative micromorphology analysissoftware SPMIAS developed by the author. Images at the same position but with different scanning ranges areobtained under the same experimental conditions. Micromorphology parameters are calculated and compared, andthe relationship between the changing of the scanning range and the changing of micromorphology parameters issummarized.展开更多
Transition metal ditellurides(TMTDs)have versatile physical properties,including non-trivial topology,Weyl semimetal states and unique spin texture.Controlled growth of high-quality and large-scale monolayer TMTDs wit...Transition metal ditellurides(TMTDs)have versatile physical properties,including non-trivial topology,Weyl semimetal states and unique spin texture.Controlled growth of high-quality and large-scale monolayer TMTDs with preferred crystal phases is crucial for their applications.Here,we demonstrate the epitaxial growth of 1T'-MoTe_(2) on Au(111)and graphitized silicon carbide(Gr/SiC)by molecular beam epitaxy(MBE).We investigate the morphology of the grown1T'-MoTe_(2) at the atomic level by scanning tunnelling microscopy(STM)and reveal the corresponding microscopic growth mechanism.It is found that the unique ordered Te structures preferentially deposited on Au(111)regulate the growth of monolayer single crystal 1T'-MoTe_(2),while the Mo clusters were preferentially deposited on the Gr/SiC substrate,which impedes the ordered growth of monolayer MoTe_(2).We confirm that the size of single crystal 1T'-MoTe_(2) grown on Au(111)is nearly two orders of magnitude larger than that on Gr/SiC.By scanning tunnelling spectroscopy(STS),we observe that the STS spectrum of the monolayer 1T'-MoTe_(2) nano-island at the edge is different from that at the interior,which exhibits enhanced conductivity.展开更多
基金supported by Science and Technology Commission of Shanghai Municipality (Grant No 0652NM028)Shanghai Leading Academic Discipline Project of China (B113)the International Research Training Group (IRTG)
文摘This paper illuminates the preparation of grating-like polystyrene latex monolayer structure, which can minimize the effects of the size deviation of spheres and the defect transfer on the accuracy as calibration samples for micro-scopes. The latex films are grown on freshly cleaved mica substrates by vertical deposition method. The concentration dependence of the structure and the topography of latex films is characterized by optical microscope, ultraviolet- visible transmission spectrum and scanning probe microscope. The origination of such a grating-like structure is also discussed.
文摘Scanning Probe Microscopes (SPMs) observe specimen surfaces with probes by detecting the physical amount of a material between the cantilever and the surface. SPMs have a high resolution and can measure mechanical characteristics such as stiffness, adsorptive properties, and viscoelasticity. These features make it easy to identify the surface structure of complex materials;therefore, the use of SPMs has increased in recent years. Wood cell walls are primarily composed of cellulose, hemicellulose, and lignin. It is believed that hemicellulose and lignin surround the cellulose framework;however, their detailed formation remains unknown. Therefore, we observed wood cell walls via scanning probe microscopy to try to reveal the formation of the cellulose framework. We determined that the size of the cellulose microfibril bundle and hemicellulose lignin module composite was 18.48 nm based on topography and that the size of the cellulose microfibril bundle was 15.33 nm based on phase images. In the viscoelasticity image, we found that the viscoelasticities of each cell wall of the same cell were not the same. This is because the cellulose microfibrils in each cell wall lean in different directions. The angle between the leaning of the cellulose microfibril and the cantilever affects the viscoelasticity measurement.
文摘We present the design and performance of a home-built scanning tunneling microscope （STM）, which is compact （66 mm tall and 25 mm in diameter）, yet equipped with a 3D atomic precision piezoelectric motor in which the Z coarse approach relies on a high simplic-ity friction-type walker （of our own invention） driven by an axially cut piezoelectric tube. The walker is vertically inserted in a piezoelectric scanner tube （PST） with its brim laying at on the PST end as the inertial slider （driven by the PST） for the XZ （sample plane） motion. The STM is designed to be capable of searching rare microscopic targets （defects, dopants, boundaries, nano-devices, etc.） in a macroscopic sample area （square millimeters） under extreme conditions （low temperatures, strong magnetic elds, etc.） in which it ts. It gives good atomic resolution images after scanning a highly oriented pyrolytic graphite sample in air at room temperature.
文摘The influence of vibration is already one of main obstacles for improving the nano measuring accuracy.The techniques of anti-vibration,vibration isolation and vibration compensation become an important branch in nano measuring field.Starting with the research of sensitivity to vibration of scanning tunneling microscope(STM),the theory,techniques and realization methods of nano vibration sensor based on tunnel effect are initially investigated,followed by developing the experimental devices.The experiments of the vibration detection and vibration compensation are carried out.The experimental results show that vibration sensor based on tunnel effect is characterized by high sensitivity,good frequency characteristic and the same vibratory response characteristic consistent with STM.
基金This project is supported by Foundation of National Education Ministry for Returned Overseas Chinese Scholars(No.2000367) an
文摘An experimental study on cutting amorphous alloy at nanometer scale is conducted by applying the principle and technology of scanning probe microscope(SPM) It is revealed from the experiments that cutting inside SPM is an excellent and direct way to research the material removal process at small size Based on the experimental results,the chip formation mechanism for the cutting of amorphous alloy is discussed It is found that the deformation along the direction of chip flow occurs ahead of the appearance of localized shear,and a simplified geometrical model is proposed to illustrate the deformation.
文摘The surface of a compact disk is analyzed by using SPM and the quantitative micromorphology analysissoftware SPMIAS developed by the author. Images at the same position but with different scanning ranges areobtained under the same experimental conditions. Micromorphology parameters are calculated and compared, andthe relationship between the changing of the scanning range and the changing of micromorphology parameters issummarized.
基金Project supported by the National Key R&D Program of China (Grant No.2022YFA1204302)the National Natural Science Foundation of China (Grant Nos.52022029,52221001,92263107,U23A20570,62090035,U19A2090,and 12174098)+1 种基金the Hunan Provincial Natural Science Foundation of China (Grant Nos.2022JJ30142 and 2019XK2001)in part supported by the State Key Laboratory of Powder Metallurgy,Central South University。
文摘Transition metal ditellurides(TMTDs)have versatile physical properties,including non-trivial topology,Weyl semimetal states and unique spin texture.Controlled growth of high-quality and large-scale monolayer TMTDs with preferred crystal phases is crucial for their applications.Here,we demonstrate the epitaxial growth of 1T'-MoTe_(2) on Au(111)and graphitized silicon carbide(Gr/SiC)by molecular beam epitaxy(MBE).We investigate the morphology of the grown1T'-MoTe_(2) at the atomic level by scanning tunnelling microscopy(STM)and reveal the corresponding microscopic growth mechanism.It is found that the unique ordered Te structures preferentially deposited on Au(111)regulate the growth of monolayer single crystal 1T'-MoTe_(2),while the Mo clusters were preferentially deposited on the Gr/SiC substrate,which impedes the ordered growth of monolayer MoTe_(2).We confirm that the size of single crystal 1T'-MoTe_(2) grown on Au(111)is nearly two orders of magnitude larger than that on Gr/SiC.By scanning tunnelling spectroscopy(STS),we observe that the STS spectrum of the monolayer 1T'-MoTe_(2) nano-island at the edge is different from that at the interior,which exhibits enhanced conductivity.
