Design of acceleration control schedule for adaptive cycle engine based on direct simulation model

To design the optimum acceleration control schedule for the Adaptive Cycle Engine(ACE)in the full flight envelope,this paper establishes a direct simulation model of the ACE transient state.In this model,geometric parameters are used to replace the component state parameters.The corresponding relationship between geometric parameters and component state parameters is determined by sensitivity analysis.The geometric variables are controlled when the geometric adjustment speed exceeds the limit,and at the same time the corresponding component state parameters are iterated.The gradient optimization algorism is used to optimize the ground acceleration process of ACE,and the control schedule in terms of operating point of compression components and corrected acceleration rate is used as the full-envelope acceleration control schedule based on the similarity principle.The acceleration control schedules of the triple-bypass mode and the double-bypass mode are designed in this paper.The acceleration processes under various flight conditions are simulated using the acceleration control schedules.Compared with the acceleration process with the linear geometric adjustment schedule,the acceleration performance of ACE is improved by the acceleration control schedule,with the impulse of the acceleration process of the triple-bypass mode being increased by 8.7%-12.3% and the impulse of the double-bypass mode acceleration process being increased by 11.8%-14.1%.

Improved control of intelligent excavator using proportional-integral-plus gain scheduling

Consider the design and implementation of an electro-hydraulic control system for a robotic excavator, namely the Lancaster University computerized and intelligent excavator (LUCIE). The excavator was developed to autonomously dig trenches without human intervention. One stumbling block is the achievement of adequate, accurate, quick and smooth movement under automatic control, which is difficult for traditional control algorithm, e.g. PI/PID. A gain scheduling design, based on the true digital proportional-integral-plus (PIP) control methodology, was utilized to regulate the nonlinear joint dynamics. Simulation and initial field tests both demonstrated the feasibility and robustness of proposed technique to the uncertainties of parameters, time delay and load disturbances, with the excavator arm directed along specified trajectories in a smooth, fast and accurate manner. The tracking error magnitudes for oblique straight line and horizontal straight line are less than 20 mm and 50 mm, respectively, while the velocity reaches 9 m/min.

Missile robust gain scheduling autopilot design using full block multipliers

Reduction of conservatism is one of the key and difficult problems in missile robust gain scheduling autopilot design based on multipliers.This article presents a scheme of adopting linear parameter-varying（LPV） control approach with full block multipliers to design a missile robust gain scheduling autopilot in order to eliminate conservatism.A model matching design structure with a high demand on matching precision is constructed based on the missile linear fractional transformation（LFT） model.By applying full block S-procedure and elimination lemma,a convex feasibility problem with an infinite number of constraints is formulated to satisfy robust quadratic performance specifications.Then a grid method is adopted to transform the infinite-dimensional convex feasibility problem into a solvable finite-dimensional convex feasibility problem,based on which a gain scheduling controller with linear fractional dependence on the flight Mach number and altitude is derived.Static and dynamic simulation results show the effectiveness and feasibility of the proposed scheme.

Gain Scheduling Control of Nonlinear Shock Motion Based on Equilibrium Manifold Linearization Model

The equilibrium manifold linearization model of nonlinear shock motion is of higher accuracy and lower complexity over other models such as the small perturbation model and the piecewise-linear model. This paper analyzes the physical significance of the equilibrium manifold linearization model, and the self-feedback mechanism of shock motion is revealed. This helps to describe the stability and dynamics of shock motion. Based on the model, the paper puts forwards a gain scheduling control method for nonlinear shock motion. Simulation has shown the validity of the control scheme.

Application of predictive control scheduling method to real-time periodic control tasks overrun

Based on the abort strategy of fixed periods, a novel predictive control scheduling methodology was proposed to efficiently solve overrun problems. By applying the latest control value in the prediction sequences to the control objective, the new strategy was expected to optimize the control system for better performance and yet guarantee the schedulability of all tasks under overrun. The schedulability of the real-time systems with p-period overruns was analyzed, and the corresponding stability criteria was given as well. The simulation results show that the new approach can improve the performance of control system compared to that of conventional abort strategy, it can reduce the overshoot and adjust time as well as ensure the schedulability and stability.

Using Adaptive Gain Scheduling LQR Method Control of Arm Driven Inverted Pendulum System Based on PIC18F4431

The arm driven inverted pendulum system is a highly nonlinear model, muhivariable and absolutely unstable dynamic system so it is very difficult to obtain exact mathematical model and balance the inverted pendulum with variable position of the ann. To solve this problem, this paper presents a mathematical model for arm driven inverted pendulum in mid-position configuration and an adaptive gain scheduling linear quadratic regulator control method for the stabilizing the inverted pendulum. The proposed controllers for arm driven inverted pendulum are simulated using MATLAB-SIMULINK and implemented on an experiment system using PIC 18F4431 mieroeontroller. The result of experiment system shows the control performance to be very good in a wide range stabilization of the arm position.

Motion stability and control of supercavitating vehicle with variable cavitation number

Cavitation number and speed are capable of variation during the motion of supercavitating vehicle underwater, for example, under the condition of accelerated motion stage and external disturbance. The dynamic model and control challenge associated with the longitudinal motion of supereavitating vehicle with variable cavitation number and speed have been explored. Based on the principle of cavity expansion independence the properties of cavity and the influence on planning force of body were researched. Calculation formula of efficiency of the fin was presented. Nonlinear dynamics model of variable cavitation number and speed supercavitating vehicle was established. Stabilities of the open-loop systems of different situations were analyzed. The simulations results of open-loop systems show that it is necessary to design a control method to control a supereavitating vehicle. A gain schedule controller with guaranteed H∞ performance was designed to stabilize the dive-plane dynamics of supercavitating vehicle under changing conditions.

MULTITASK SCHEDULING IN NETWORKED CONTROL SYSTEMS WITH APPLICATION TO LARGE SCALE VEHICLE CONTROL

Aiming at scheduling problems of networked control system （NCS） used to fulfill motion synthesis and cooperation control of the distributed multi-mechatronic systems, the differences of network scheduling and task scheduling are compared, and the mathematic description of task scheduling is presented. A performance index function of task scheduling of NCS according to task balance and traffic load matching principles is defined. According to this index, a static scheduling method is designed and implemented to controlling task set simulation of the DCY100 transportation vehicle. The simulation results are applied successfully to practical engineering in this case so as to validate the effectiveness of the proposed performance index and scheduling algorithm.

Designing method of acceleration and deceleration control schedule for variable cycle engine

Studies show that different geometries of a Variable Cycle Engine(VCE)can be adjusted during the transient stage of the engine operation to improve the engine performance.However,this improvement increases the complexity of the acceleration and deceleration control schedule.In order to resolve this problem,the Transient-state Reverse Method(TRM)is established in the present study based on the Steady-state Reverse Method(SRM)and the Virtual Power Extraction Method(VPEM).The state factors in the component-based engine performance models are replaced by variable geometry parameters to establish the TRM for a double bypass VCE.Obtained results are compared with the conventional component-based model from different aspects,including the accuracy and the convergence rate.The TRM is then employed to optimize the control schedule of a VCE.Obtained results show that the accuracy and the convergence rate of the proposed method are consistent with that of the conventional model.On the other hand,it is found that the new-model-optimized control schedules reduce the acceleration and deceleration time by 45%and 54%,respectively.Meanwhile,the surge margin of compressors,fuel–air ratio and the turbine inlet temperature maintained are within the acceptable criteria.It is concluded that the proposed TRM is a powerful method to design the acceleration and deceleration control schedule of the VCE.

Design method of optimal control schedule for the adaptive cycle engine steady-state performance

The alternative working modes and flexible working states are the outstanding features of an adaptive cycle engine, with a proper control schedule design being the only way to exploit the performance of such an engine. However, unreasonable design in the control schedule causes not only performance deterioration but also serious aerodynamic stability problems. Thus, in this work,a hybrid optimization method that automatically chooses the working modes and identifies the optimal and smooth control schedules is proposed, by combining the differential evolution algorithm and the Latin hypercube sampling method. The control schedule architecture does not only optimize the engine steady-state performance under different working modes but also solves the control-schedule discontinuity problem, especially during mode transition. The optimal control schedules are continuous and almost monotonic, and hence are strongly suitable for a control system, and are designed for two different working conditions, i.e., supersonic and subsonic throttling,which proves that the proposed hybrid method applies to various working conditions. The evaluation demonstrates that the proposed control method optimizes the engine performance, the surge margin of the compression components, and the range of the thrust during throttling.

End-to-End Utilization Control for Aperiodic Tasks in Distributed Real-Time Systems

An increasing number of DRTS （Distributed model. The key challenges of such DRTS are guaranteeing Real-Time Systems） are employing an end-to-end aperiodic task utilization on multiple processors to achieve overload protection, and meeting the end-to-end deadlines of aperiodic tasks. This paper proposes an end-to-end utilization control architecture and an IC-EAT （Integration Control for End-to-End Aperiodic Tasks） algorithm, which features a distributed feedback loop that dynamically enforces the desired utilization bound on multiple processors. IC-EAT integrates admission control with feedback control, which is able to dynamically determine the QoS （Quality of Service） of incoming tasks and guarantee the end-to-end deadlines of admitted tasks. Then an LQOCM （Linear Quadratic Optimal Control Model） is presented. Finally, experiments demonstrate that, for the end-to-end DRTS whose control matrix G falls into the stable region, the IC-EAT is convergent and stable. Moreover,it is capable of providing better QoS guarantees for end-to-end aperiodic tasks and improving the system throughput.

SEMI-DEFINITE RELAXATION ALGORITHM FOR SINGLE MACHINE SCHEDULING WITH CONTROLLABLE PROCESSING TIMES

The authors present a semi-definite relaxation algorithm for the scheduling problem with controllable times on a single machine. Their approach shows how to relate this problem with the maximum vertex-cover problem with kernel constraints (MKVC).The established relationship enables to transfer the approximate solutions of MKVCinto the approximate solutions for the scheduling problem. Then, they show how to obtain an integer approximate solution for MKVC based on the semi-definite relaxation and randomized rounding technique.