A novel seismic design method, namely split-pier seismic design, is proposed. A vertical gap and connect elements are set in split-piers. The lateral stiffness of piers is reduced by cracking of the connect elements u...A novel seismic design method, namely split-pier seismic design, is proposed. A vertical gap and connect elements are set in split-piers. The lateral stiffness of piers is reduced by cracking of the connect elements under severe earthquake, and the seismic response of bridges is reduced by avoiding the site predominant periods. A model of tied-arch rigid frame bridge with split-piers was designed. Seismic performance was investigated by pseudo-static experimentation on the scale model, The failure process of split-piers, the hysteresis characteristic and the effect of split-piers on the superstructure are presented. Results show that the split-pier has better seismic performance than common ductile piers do.展开更多
Mechanical behavior of concrete slab of large-span through tied-arch composite bridge was investigated by finite element analysis (FEA). Improved methods to decrease concrete stresses were discussed based on compariso...Mechanical behavior of concrete slab of large-span through tied-arch composite bridge was investigated by finite element analysis (FEA). Improved methods to decrease concrete stresses were discussed based on comparisons of different deck schemes, construction sequences and measures, and ratios of reinforcement. The results show that the mechanical behavior of concrete slab gets worse with the increase of composite regions between steel beams and concrete slab. The deck scheme with the minimum composite region is recommended on condition that both strength and stiffness of the bridge meet design demands under service loads. Adopting in-situ-place construction method, concrete is suggested to be cast after removing the full-supported frameworks under the bridge. Thus, the axial tensile force of concrete slab caused by the first stage dead load is eliminated. Preloading the bridge before concrete casting and removing the load after the concrete reaching its design strength, the stresses of concrete slab caused by the second stage dead load and live load are further reduced or even eliminated. At last, with a high ratio of reinforcement more than 3%, the concrete stresses decrease obviously.展开更多
Condition assessment of bridges has become increasingly important. In order to accurately simulate the real bridge, finite element （FE） model updating method is often applied. This paper presents the calibration of ...Condition assessment of bridges has become increasingly important. In order to accurately simulate the real bridge, finite element （FE） model updating method is often applied. This paper presents the calibration of the FE model of a reinforced concrete tied-arch bridge using Douglas-Reid method in combination with Rosenbrock optimization algorithm. Based on original drawings and topographic survey, a FE model of the investigated bridge is created. Eight global modes of vibration of the bridge are identified by ambient vibration tests and the frequency domain decomposition technique. Then, eight structural parameters are selected for FE model updating procedure through sensitivity analysis. Finally, the optimal structural parameters are identified using Rosenbrock optimization algorithm. Results show that although the identified parameters lead to a perfect agreement between approximate and measured natural frequencies, they may not be the optimal variables which minimize the differences between numerical and experimental modal data. However, a satisfied agreement between them is still presented. Hence, FE model updating based on Douglas-Reid method and Rosenbrock optimization algorithm could be used as an alternative to other complex updating procedures.展开更多
基金The Natural Science Foundation of Jiangsu Province(NoBK2002061)
文摘A novel seismic design method, namely split-pier seismic design, is proposed. A vertical gap and connect elements are set in split-piers. The lateral stiffness of piers is reduced by cracking of the connect elements under severe earthquake, and the seismic response of bridges is reduced by avoiding the site predominant periods. A model of tied-arch rigid frame bridge with split-piers was designed. Seismic performance was investigated by pseudo-static experimentation on the scale model, The failure process of split-piers, the hysteresis characteristic and the effect of split-piers on the superstructure are presented. Results show that the split-pier has better seismic performance than common ductile piers do.
基金Project(2005k002-c-2) supported by the Science and Technology Development Program of Railways Department, China
文摘Mechanical behavior of concrete slab of large-span through tied-arch composite bridge was investigated by finite element analysis (FEA). Improved methods to decrease concrete stresses were discussed based on comparisons of different deck schemes, construction sequences and measures, and ratios of reinforcement. The results show that the mechanical behavior of concrete slab gets worse with the increase of composite regions between steel beams and concrete slab. The deck scheme with the minimum composite region is recommended on condition that both strength and stiffness of the bridge meet design demands under service loads. Adopting in-situ-place construction method, concrete is suggested to be cast after removing the full-supported frameworks under the bridge. Thus, the axial tensile force of concrete slab caused by the first stage dead load is eliminated. Preloading the bridge before concrete casting and removing the load after the concrete reaching its design strength, the stresses of concrete slab caused by the second stage dead load and live load are further reduced or even eliminated. At last, with a high ratio of reinforcement more than 3%, the concrete stresses decrease obviously.
文摘Condition assessment of bridges has become increasingly important. In order to accurately simulate the real bridge, finite element （FE） model updating method is often applied. This paper presents the calibration of the FE model of a reinforced concrete tied-arch bridge using Douglas-Reid method in combination with Rosenbrock optimization algorithm. Based on original drawings and topographic survey, a FE model of the investigated bridge is created. Eight global modes of vibration of the bridge are identified by ambient vibration tests and the frequency domain decomposition technique. Then, eight structural parameters are selected for FE model updating procedure through sensitivity analysis. Finally, the optimal structural parameters are identified using Rosenbrock optimization algorithm. Results show that although the identified parameters lead to a perfect agreement between approximate and measured natural frequencies, they may not be the optimal variables which minimize the differences between numerical and experimental modal data. However, a satisfied agreement between them is still presented. Hence, FE model updating based on Douglas-Reid method and Rosenbrock optimization algorithm could be used as an alternative to other complex updating procedures.
