Characteristics and formation of high quality reservoirs in sediment gravity flows of Gangzhong area,Huanghua depression

Reservoirs can be developed in the sediment gravity flows.However,high quality reservoirs are found widespread in sediment gravity flows of Gangzhong area,Huanghua depression,Bohai Bay Basin,East China.Characteristics and formation of these reservoirs are key problems to be solved.Through comprehensive analysis of thin section petrography,scanning electron microscopy and X-ray diffraction,two distinct rules were obtained.1) These high quality reservoirs have apparent characteristics:lithology consists mainly of medium-fine grained sands; moderately-well sorted and rounded; intergranular pores dominating >70% of the entire pores,surface per unit pore volume reaches 15%; average porosity is 21% and average permeability is 55×10-3 μm2.2) Types of sedimentary microfacies and dissolution strongly control on the formation of high quality reservoirs.Main channels and sandy braided bars have the best reservoir properties.Because that sediments are mainly medium-fine grained sands in high-energy environments.The favorable primary porosity and permeability may promote calcite cementation and help to produce more secondary pores.Besides,at the depth of 2500-3200 m,basically matching threshold of oil generation,organic acid expelled when organic matter became mature,and H+ released during clay mineral transformation.These both result in the dissolution of calcite cements and create large volume pores,then physical properties improve correspondingly.Moreover,deep hydrothermal fluid intrusion may also have impacts on the development of secondary pores.

Experimental investigation of the effect of flow turbulence and sediment transport patterns on the adsorption of cadmium ions onto sediment particles

The mechanism of flow turbulence, sediment supply conditions, and sediment transport patterns that affect the adsorption of cadmium ions onto sediment particles in natural waters are experimentally simulated and studied both in batch reactors and in a turbulence simulation tank. By changing the agitation conditions, the sediment transport in batch reactors can be categorized into bottom sediment-dominated sediment and suspended sediment-dominated sediment. It is found that the adsorption rate of bottom sediment is much less than that of suspended sediment, but the sediment transport pattern does not affect the final （equilibrium） concentration of dissolved cadmium. This result indicates that the parameters of an adsorption isotherm are the same regardless of the sediment transport pattern. In the turbulence simulation tank, the turbulence is generated by harmonic grid-stirred motions, and the turbulence intensity is quantified in terms of eddy diffusivity, which is equal to 9.84F （F is the harmonic vibration frequency） and is comparable to natural surface water conditions. When the turbulence intensity of flow is low and sediment particles stay as bottom sediment, the adsorption rate is significantly low, and the adsorption quantity compared with that of suspended sediment is negligible in the 6 h duration of the experiment. This result greatly favors the simplification of the numerical modeling of heavy metal pollutant transformation in natural rivers. When the turbulence intensity is high but bottom sediment persists, the rate and extent of descent of the dissolved cadmium concentration in the tank noticeably increase, and the time that is required to reach adsorption equilibrium also increases considerably due to the continuous exchange that occurs between the suspended sediment and the bottom sediment. A comparison of the results of the experiments in the batch reactor and those in the turbulence simulation tank reveals that the adsorption ability of the sediment, and in particular the adsorption rate, is greatly over-estimated in the batch reactor.

Numerical simulations of flow and sediment transport within the Ning-Meng reach of the Yellow River,northern China

Effective management of a river reach requires a sound understanding of flow and sediment transport generated by varying natural and artificial runoff conditions. Flow and sediment transport within the Ning-Meng reach of the Yellow River（NMRYR）, northern China are controlled by a complex set of factors/processes, mainly including four sets of factors：（1） aeolian sediments from deserts bordering the main stream;（2） inflow of water and sediment from numerous tributaries;（3） impoundment of water by reservoir/hydro-junction; and（4） complex diversion and return of irrigation water. In this study, the 1-D flow ＆ sediment transport model developed by the Yellow River Institute of Hydraulic Research was used to simulate the flow and sediment transport within the NMRYR from 2001 to 2012. All four sets of factors that primarily control the flow and sediment transport mentioned above were considered in this model. Compared to the measured data collected from the hydrological stations along the NMRYR, the simulated flow and sediment transport values were generally acceptable, with relative mean deviation between measured and simulated values of 〈15%. However, simulated sediment concentration and siltation values within two sub-reaches（i.e., Qingtongxia Reservoir to Bayan Gol Hydrological Station and Bayan Gol Hydrological Station to Toudaoguai Hydrological Station） for some periods exhibited relatively large errors（the relative mean deviations between measured and simulated values of 18% and 25%, respectively）. These errors are presumably related to the inability to accurately determine the quantity of aeolian sediment influx to the river reach and the inflow of water from the ten ephemeral tributaries. This study may provide some valuable insights into the numerical simulations of flow and sediment transport in large watersheds and also provide a useful model for the effective management of the NMRYR.

THE STUDY ON THREE-DIMENSIONAL MATHEMATICAL MODEL OF RIVER BED EROSION FOR WATER-SEDIMENT TWO-PHASE FLOW

Based on the tensor analysis of water-sediment two-phase how, the basic model equations for clear water flow and sediment-laden flow are deduced in the general curve coordinates for natural water variable-density turbulent how. Furthermore, corresponding boundary conditions are also presented in connection with the composition and movement of non-uniform bed material. The theoretical results are applied to the calculation of the float open caisson in the construction period and good results are obtained.

Effects of Rigid Vegetation on the Turbulence Characteristics in Sediment-Laden Flows

The effects of rigid vegetation on the turbulence characteristics were experimentally studied in the interior water flume. An ADV was used to determine the three dimensional turbulent velocities in clear water flow without vegetation, sediment-laden flow without vegetation, sediment-laden flow with submerged vegetation and sediment-laden flow with non-submerged vegetation. By experimental and theoretical analysis, the effects of rigid vegetation on the distribution of averaged velocities, turbulence intensities and Reynolds stress were summarized. In sediment-laden flow with submerged vegetation, the averaged stream wise velocities above the top of vegetation fit well with the log distribution low. The three-dimensional turbulence intensities increase from the bottom until they reach the maximum at the top of the vegetation. The method to calculate the shear velocity with the maximum of the Reynolds stress is recommended. In sediment-laden flow with non-submerged vegetation, the turbulence problems cannot be explained by theory of bed shear flow. The average velocities, turbulence intensities and Reynolds stress approximate uniformly distributed along vertical direction.

Effects of sediment load on the abrasion of soil aggregate and hydraulic parameters in experimental overland flow

The breakdown of soil aggregates under rainfall and their abrasion in overland flow are important processes in water erosion due to the production of more fine and transportable particles and,the subsequent significant effect on the erosion intensity.Currently,little is known about the effects of sediment load on the soil aggregate abrasion and the relationship of this abrasion with some related hydraulic parameters.Here,the potential effects of sediment load on soil aggregate abrasion and hydraulic parameters in overland flow were investigated through a series of experiments in a 3.8-m-long hydraulic flume at the slope gradients of 8.7 and 26.8%,unit flow discharges from 2×10^-3 to 6×10^-3 m^2 s^-1,and the sediment concentration from 0 to 110 kg m-3.All the aggregates from Ultisols developed Quaternary red clay,Central China.The results indicated that discharge had the most significant(P<0.01)effect on the aggregates abrasion with the contributions of 58.76 and 60.34%,followed by sediment feed rate,with contributions of 39.66 and 34.12%at the slope gradients of 8.7 and 26.8%,respectively.The abrasion degree of aggregates was found to increase as a power function of the sediment concentration.Meanwhile,the flow depth,friction factor,and shear stress increased as a power function along with the increase of sediment concentration at different slope gradients and discharges.Reynolds number was obviously affected by sediment concentration and it decreased as sediment concentration increased.The ratio of the residual weight to the initial weight of soil aggregates(Wr/Wi)was found to increase as the linear function with an increasing flow depth(P=0.008)or Reynolds number(P=0.002)in the sediment-laden flow.The Wr/Wi values followed a power function decrease with increasing friction factor or shear stress in the sediment-laden flow,indicating that friction factor is the best hydraulic parameter for prediction of soil aggregate abrasion under different sediment load conditions.The information regarding the soil aggregate abrasion under various sediment load conditions can facilitate soil process-based erosion modeling.

A Higher-Efficient Non-Hydrostatic Finite Volume Model for Strong Three-Dimensional Free Surface Flows and Sediment Transport

In order to accurately simulate strong three-dimensional （3-D） free surface flows and sediment transport, the fully 3- D non-hydrostatic pressure models are developed based on the incompressible Navier-Stokes equations and convection-diffusion equation of sediment concentration with the mixing triangle and quadrilateral grids. The governing equations are discretized with the unstructured finite volume method in order to provide conservation properties of mass and momentum, and flexibility with practical application. It is shown that it is first-order accurate on nonuniform plane two-dimensional （2-D） grids and second-order accurate on uniform plane grids. A third-order approximation of the vertical velocity at the top-layer is applied. In such a way, free surface zero stress boundary condition is satisfied maturely, and very few vertical layers are needed to give an accurate solution even for complex discontinuous flow and short wave simulation. The model is applied to four examples to simulate strong 3-D free surface flows and sediment transport where non-hydrostatic pressures have a considerable effect on the velocity field. The newly developed model is verified against analytical solutions with an excellent agreement.

INFLUENCES OF THE FISH-MOUTH PROJECT AND THE GROINS ON THE FLOW AND SEDIMENT RATIO OF THE YANGTZE RIVER WATERWAY

A depth_integrated two_dimensional numerical model of current, salinity and sediment transport was proposed and calibrated by the observation data in the Yangtze River Estuary. It was then applied to investigate the flow and sediment ratio of the navigation channel, i.e. the North Channel of the Yangtze River Estuary,before and after the first phase waterway project is implemented. Particularly, the influences of groin length and the orientation of the submerged dam on the flow ratio and sediment load discharging into the North Channel were discussed. The numerical results demonstrate that less sediment load discharges into the navigation channel, which unburdens the waterway dredging, but in the meantime the flow ratio is also decreased. The flow and sediment ratio can be adjusted by changing layout and dimensions of the hydro_structures, such as the groin length, the top height, etc. The effect of the orientation of the submerged dam is more obvious than the groin lengh.

Probability of Sediment Incipient Motion Under Complex Flows

Presented in this paper is a mathematical model to calculate the probability of the sediment incipient motion, in which the effects of the fluctuating pressure and the seepage are considered. The instantaneous bed shear velocity and the pressure gradient on the bed downstream of the backward-facing step flow are obtained according to the PIV measurements. It is found that the instantaneous pressure gradient on the bed obeys normal distribution. The probability of the sediment incipient motion on the bed downstream of the backward-facing step flow is given by the mathematical model. The predicted results agree well with the experiment in the region downstream of the reattachment point while a large discrepancy between the theory and experiment is seen in the region near the reattachment point. The possible reasons for this discrepancy are discussed.

Wave-Enhanced Sediment-Gravity Flows in Bohai Bay Lacustrine Basin, Eastern China

Sequences of wave-enhanced sediment-gravity flows(WESGFs) have been widely recognized in the marine shelf environment. In this study, we show observations of WESGF deposits in lacustrine settings using well core and thin section data from the Paleogene in the Jiyang sub-basin, Bohai Bay basin, eastern China. The findings of this study include the following: 1) the sequence of WESGFs in the lacustrine basin is similar to that of marine; it consists of three units, MF1 unit: siltstone with basal erosion surface, MF2 unit: silt-streaked claystone, and MF3 unit: silty-mudstone; and 2) prodelta sand sheets are found in the lacustrine WESGF sequence and are classified as the MFd unit: clay-streaked siltstone. However, because the system size and variability in hydrodynamic conditions are different between the lacustrine and marine basins, lacustrine WESGFs do appear to have three distinguishable features: 1) the sediment grain size and sand content are slightly higher than those of the marine WESGFs; 2) lacustrine WESGFs may contain prodelta sediments or sedimentary sequences of other types of gravity flows, such as hyperpycnal flows; and 3) the scale of the sedimentary structures for lacustrine WESGFs is smaller. The WESGFs found in the continental lacustrine basin provide a new model for sediment dispersal processes in lake environments and may be helpful to explain and predict the distribution of sandy reservoirs for oil and gas exploration.

Coupled Model of Two-phase Debris Flow,Sediment Transport and Morphological Evolution

The volume fraction of the solid and liquid phase of debris flows, which evolves simultaneously across terrains, largely determines the dynamic property of debris flows. The entrainment process significantly influences the amplitude of the volume fraction. In this paper, we present a depth-averaged two-phase debris-flow model describing the simultaneous evolution of the phase velocity and depth, the solid and fluid volume fractions and the bed morphological evolution. The model employs the Mohr–Coulomb plasticity for the solid stress, and the fluid stress is modeled as a Newtonian viscous stress. The interfacial momentum transfer includes viscous drag and buoyancy. A new extended entrainment rate formula that satisfies the boundary momentum jump condition （Iverson and Ouyang, 2015） is presented. In this formula, the basal traction stress is a function of the solid volume fraction and can take advantage of both the Coulomb and velocity-dependent friction models. A finite volume method using Roe’s Riemann approximation is suggested to solve the equations. Three computational cases are conducted and compared with experiments or previous results. The results show that the current computational model and framework are robust and suitable for capturing the characteristics of debris flows.

Experiment on the Effect of Sediment Concentration on Flow Structure

The paper studies on the sediment-laden flow by using MicroADV.Laboratory calibration has been conducted to determine the relationship between backscattered signal strength and sediment concentration. Based on the experimental data,the interactions between sediment and fluid in open channel flow are investi- gated.The experiment shows that there exist inner relation between sediment concentration and turbulence, and the relationship is distinctry related to the diameter of particle as well as the flow co...

Sediment Transport in Rivers with Overbank Flow

Some concepts related to sediment transport in rivers with overbank flow are described.Following a description of the physical processes that are involved when a river inundates its floodplains,some simple com- putational methods are presented which permit the depth-averaged velocity and boundary shear stress to be pre- dicted within a cross section of variable,but prismatic shape.The methoda account for the strong transverse shear in velocity that occurs when the stage is just above bankfull,as well as ...

Environmental Flow Assessment Using Water-Sediment Approach at the Sekampung River, Indonesia

Environmental issue has been considered more significant in many aspects of engineering decision-making process particularly in river management. There is an increasing effort to conserve functioning of rivers for human use as well as nature, therefore environmental flow assessment has been widely developed. This paper discusses on environmental flow assessment of the Sekampung River, particularly on its middle reach. A new analytical approach based on water-sediment equations was introduced in order to determine a minimum environmental flow at the certain cross section of a river. The result of the new method was then compared with a minimum environmental flow provided by using two hydrological based methods, namely, Tennant and Flow Duration Curve Analysis (FDCA) method. The result shows that the concerned discharge provided by the water-sediment method (3.5 m3/s) is the smallest compare with a minimum environmental flow that is provided by both Tennant (5.7 m3/s) and FDCA method (4.5 m3/s). It is promising that the water-sediment method can be used as a simple approach on preliminary state of environmental flow assessment. The method involves not only water discharge but also its related sediment flow of the river in order to mitigate further ecological and morphological risks.

Criteria for Distinguishing Floc Sedimentation and Gel-Like Network Sedimentation of Cohesive Fine-Grained Sediment in a Turbulent Flow

The study on the criteria used to distinguish floc sedimentation and gel-like network sedimentation of cohesive fine-grained sediment in a turbulent flow has rarely been carried out. In this preliminary study, we derive three criteria to distinguish these two different sedimentation phases by considering the comparison of the time that a characteristic floc takes to settle through mean distance between characteristic flocs and the time that it takes to move through the same distance under the influence of a turbulent flow. These criteria incorporate physical and chemical factors that have been verified to have some influences on the sediment flocculation in some published literatures, and a simple analysis result is found to be consistent with our qualitative understandings of flocculation phenomenon of cohesive fine-grained sediment.

Water Flow and Sediment Flux Forecast in the ChókwèIrrigation Scheme, Mozambique

This study sought to forecast water flow and sediment flux in the scheme as potential contributions for improved management in the Chókwè Irrigation Scheme (CIS). Fieldwork data was collected during dry (DS) and wet (WS) seasons. Flow measurement was performed at 9 stations using a calibrated flow meter OTT C31. Water flow and sediment flux from 2004 to 2019 were used. Hydrodynamic forecast simulations were performed using Mann-Kendall test and ARIMA model for determination of temporal trends. Findings suggest higher values during DS for water discharge and sediment flux. Mann-Kendall test for sediment discharge trends was not significant at 95% significance level, except for the Offtake in WS. ARIMA test for the sediment discharges, at the Intake, for DS and WS, sediments were well described by the ARIMA model and gave a good result for the sediments. Good fit between the observed and the predicted ARIMA model was found. ARIMA model for sediment discharge at CIS based on AIC has a good fit for AR (p = 1), whereby, at the Intake the ARIMA p-value was 0.822 and 0.932, for WS and DS, respectively. Whilst in the Offtake, the ARIMA p-value was 0.877 and 0.893, respectively. These results can be used to improve the CIS management, both for water flow and sediment flux.

Vertical Migration of Fine-Grained Sediments from Interior to Surface of Seabed Driven by Seepage Flows–‘Sub-Bottom Sediment Pump Action'

A scientific hypothesis is proposed and preliminarily verified in this paper: under the driving of seepage flows, there might be a vertical migration of fine-grained soil particles from interior to surface of seabed, which is defined as ‘sub-bottom sediment pump action' in this paper. Field experiments were performed twice on the intertidal flat of the Yellow River delta to study this process via both trapping the pumped materials and recording the pore pressures in the substrate. Experimental results are quite interesting as we did observe yellow slurry which is mainly composed of fine-grained soil particles appearing on the seabed surface; seepage gradients were also detected in the intertidal flat, under the action of tides and small wind waves. Preliminary conclusions are that ‘sediment pump' occurs when seepage force exceeds a certain threshold: firstly, it is big enough to disconnect the soil particles from the soil skeleton; secondly, the degree of seabed fluidization or bioturbation is big enough to provide preferred paths for the detached materials to migrate upwards. Then they would be firstly pumped from interior to the surface of seabed and then easily re-suspended into overlying water column. Influential factors of ‘sediment pump' are determined as hydrodynamics(wave energy), degree of consolidation, index of bioturbation(permeability) and content of fine-grained materials(sedimentary age). This new perspective of ‘sediment pump' may provide some implications for the mechanism interpretation of several unclear geological phenomena in the Yellow River delta area.

Influence of Tea Plantations, Forest and Mixed Farming on Stream Flow and Sediment Loads, Case of Sondu Miriu River Basin, Kenya

The changing patterns of land cover and land use in the tropical river basin over time are critical. The hydrological phenomena at basin and sub basin scale are affected positively or negatively by dynamics of the land cover and land use patterns. Hence identifying causes and driving factors aid in taking appropriate measures to avert the impacts. This study determined the influences of sub basins dominated by tea plantations, forests and agricultural land uses in terms of streamflow and sediment flux variability in Sondu Miriu River Basin in Kenya, East Africa. Field-based investigations were conducted through sampling of flow velocities, turbidity and TSSC obtained from existing River Gauging Stations established within the three sub basins. The sub basin dominated by mixed farming land cover exhibits high turbidity approximately 620 NTU and high levels of total suspended sediment concentration (TSSC) of the order of 630 mg/l in wet seasons. The turbidity levels and TSSC were low in sub basins dominated by forest and tea plantations with approximately mean value of 17 - 29 NTU and 0.019 g/l. The sediment loads in sub basin dominated by mixed farming in the pre planting season in January to February were about 900 tonnes/day higher than that in crop growing season. In sub basins dominated by forest cover and tea plantations, sediment loads were low ranging between 2 - 7 tonnes/day. The relationship between stream flows and area under tea plantations, forests and mixed farming ranged between R2 of 0.025 and 0.16. Tea plantations and forests influence the stream flows and sediment yields in long term duration while in mixed farming variations were observed seasonally. The strong relationships between rainfall and stream flows at the sub basins ranging between R2 of 0.84 and 0.97 revealed the significance of rainfall in hydrologic response of the Sondu Miriu River Basin.

Experimental Investigation on Flow Characteristics at Leeside of Suspended Flexible Curtain for Sedimentation Enhancement

A new patent registered device- suspended flexible curtain （SFC） for sedimentation enhancement is proposed in this paper, which consists of two parts： a light-weight curtain with sediment-passing windows and a heavy pillar for the device stability. The mechanism of trapping nearbed sediment by the SFC is such that a primary and a secondary circulations with horizontal hubs would be formed at the leeside when it is placed on beds in running flow; the velocities within the sediment-passing windows are locally accelerated, the nearbed sediments would be brought by the flow through the windows, and then settled down within the primary circulation zone. Experimental tests on hydraulic characteristics are conducted in a laboratory flume with rigid bed. It is found that the dimensions of the curtain and the sediment-passing windows determine the characteristics of the primary and the secondary circulations. The intensity of the primary and the secondary circulations is dominated by the size of the sediment-passing window. Whether the secondary circulation would contact the bed or not depends on the level of the sediment-passing window. The length and the height of the primary circulation zone demonstrate quasi linear relationships with the effective height of the SFC. And the tests on sandy bed flume show that the sediment deposition happens just in the primary circulation zone.