First demonstration of a self-aligned p-channel GaN back gate injection transistor

In this study,we present the development of self-aligned p-channel Ga N back gate injection transistors(SA-BGITs)that exhibit a high ON-state current.This achievement is primarily attributed to the conductivity modulation effect of the 2-D electron gas(2DEG,the back gate)beneath the 2-D hole gas(2DHG)channel.SA-BGITs with a gate length of 1μm have achieved an impressive peak drain current(I_(D,MAX))of 9.9 m A/mm.The fabricated SA-BGITs also possess a threshold voltage of 0.15 V,an exceptionally minimal threshold hysteresis of 0.2 V,a high switching ratio of 10~7,and a reduced ON-resistance(RON)of 548Ω·mm.Additionally,the SA-BGITs exhibit a steep sub-threshold swing(SS)of 173 mV/dec,further highlighting their suitability for integration into Ga N logic circuits.

A 162GHz Self-Aligned InP/InGaAs Heterojunction Bipolar Transistor

An emitter self-aligned InP-based single heterojunction bipolar transistor with a cutoff frequency （fT） of 162GHz is reported. The emitter size is 0.8μm × 12μm, the maximum DC gain is 120, the offset voltage is 0.10V,and the typical breakdown voltage at Ic = 0. 1μA is 3.8V. This device is suitable for high-speed low-power applications,such as OEIC receivers and analog-to-digital converters.

Performance of a Self-Aligned InP/GaInAs SHBT with a Novel T-Shaped Emitter

A self-aligned InP/GalnAs single heterojunction bipolar transistor（HBT） is investigated using a novel T-shaped emitter. A U-shaped emitter layout,selective wet etching,laterally etched undercut, and an air-bridge are applied in this process. The device, which has a 2μm×12μm U-shaped emitter area,demonstrates a common-emitter DC current gain of 170,an offset voltage of 0.2V,a knee voltage of 0.5V, and an open-base breakdown voltage of over 2V. The HBT exhibits good microwave performance with a current gain cutoff frequency of 85GHz and a maximum oscillation frequency of 72GHz, These results indicate that these InP/InGaAs SHBTs are suitable for low-voltage,low-power,and high-frequency applications.

Scalable fabrication of geometry-tunable self-aligned superlattice photonic crystals for spectrum-programmable light trapping

Superlattice photonic crystals (SPhCs) possess considerablepotentials as building blocks for constructing high-performancedevices because of their great flexibilities in opticalmanipulation. From the prospective of practical applications,scalable fabrication of SPhCs with large-area uniformity and precisegeometrical controllability has been considered as one prerequisitebut still remains a challenge.

Fabrication and characterization of groove-gate MOSFETs based on a self-aligned CMOS process

N and P-channel groove-gate MOSFETs based on a self-aligned CMOS process have been fabricated and characterized. For the devices with channel length of 140nm, the measured drain induced barrier lowering （DIBL） was 66mV/V for n-MOSFETs and 82mV/V for p-MOSFETs. The substrate current of a groove-gate n-MOSFET was 150 times less than that of a conventional planar n-MOSFET, These results demonstrate that groove-gate MOSFETs have excellent capabilities in suppressing short-channel effects. It is worth emphasizing that our groove-gate MOSFET devices are fabricated by using a simple process flow, with the potential of fabricating devices in the sub-100nm range.

Self-Aligned Titanium Silicide NMOS and 12-Bit Multiplier

Self-aligned Titanium Silicide (Salicide), Light-Doped Drain (LDD) technology was studied. Results show that, this technology suppresses effectivily short-channel effects. The sheet resistance of active region decreases by four times. The sheet resistance of polysilicon gate region decreases by one order of magnitute. Using this technology, the speed of the 3 μm NMOS 12-bits multiplier increases by two times relative to conventional one.

Excellent-Performance AlGaN/GaN Fin-MOSHEMTs with Self-Aligned Al_2O_3Gate Dielectric

A1GaN/GaN fin-shaped metal-oxide-semiconductor high-electron-mobility transistors （fin-MOSHEMTs） with dif- ferent fin widths （30Ohm and lOOnm） on sapphire substrates are fabricated and characterized. High-quality self-Migned Al2O3 gate dielectric underneath an 80-nm T-shaped gate is employed by Muminum self-oxidation, which induces 4 orders of magnitude reduction in the gate leakage current. Compared with conventional planar MOSHEMTs, short channel effects of the fabricated fin-MOSHEMTs are significantly suppressed due to the tri- gate structure, and excellent de characteristics are obtained, such as extremely fiat output curves, smaller drain induced barrier lower, smaller subthreshold swing, more positive threshold voltage, higher transconductance and higher breakdown voltage.

Innovation on Line Cut Methods of Self-aligned Multiple Patterning

Self-aligned multiple patterning (SAMP) can enable the semiconductor scaling before EUV lithography becomes mature for industry use.Theoretically any small size of pitch can be achieved by repeating SADP on same wafer but with challenges of pitch walking and line cut since line cut has to be done by lithography instead of self-aligned method.Line cut can become an issue at sub-30nm pitch due to edge placement error (EPE).In this paper we will discuss some recent novel ideas on line cut after self-aligned multiple patterning.

A novel self-alignment method for high precision silicon diffraction microlens arrays preparation and its integration with infrared focal plane arrays

Silicon(Si)diffraction microlens arrays are usually used to integrating with infrared focal plane arrays(IRFPAs)to improve their performance.The errors of lithography are unavoidable in the process of the Si diffrac-tion microlens arrays preparation in the conventional engraving method.It has a serious impact on its performance and subsequent applications.In response to the problem of errors of Si diffraction microlens arrays in the conven-tional method,a novel self-alignment method for high precision Si diffraction microlens arrays preparation is pro-posed.The accuracy of the Si diffractive microlens arrays preparation is determined by the accuracy of the first li-thography mask in the novel self-alignment method.In the subsequent etching,the etched area will be protected by the mask layer and the sacrifice layer or the protective layer.The unprotection area is carved to effectively block the non-etching areas,accurately etch the etching area required,and solve the problem of errors.The high precision Si diffraction microlens arrays are obtained by the novel self-alignment method and the diffraction effi-ciency could reach 92.6%.After integrating with IRFPAs,the average blackbody responsity increased by 8.3%,and the average blackbody detectivity increased by 10.3%.It indicates that the Si diffraction microlens arrays can improve the filling factor and reduce crosstalk of IRFPAs through convergence,thereby improving the perfor-mance of the IRFPAs.The results are of great reference significance for improving their performance through opti-mizing the preparation level of micro nano devices.

Type Synthesis of Self-Alignment Parallel Ankle Rehabilitation Robot with Suitable Passive Degrees of Freedom

The current parallel ankle rehabilitation robot(ARR)suffers from the problem of difficult real-time alignment of the human-robot joint center of rotation,which may lead to secondary injuries to the patient.This study investigates type synthesis of a parallel self-alignment ankle rehabilitation robot(PSAARR)based on the kinematic characteristics of ankle joint rotation center drift from the perspective of introducing"suitable passive degrees of freedom(DOF)"with a suitable number and form.First,the self-alignment principle of parallel ARR was proposed by deriving conditions for transforming a human-robot closed chain(HRCC)formed by an ARR and human body into a kinematic suitable constrained system and introducing conditions of"decoupled"and"less limb".Second,the relationship between the self-alignment principle and actuation wrenches(twists)of PSAARR was analyzed with the velocity Jacobian matrix as a"bridge".Subsequently,the type synthesis conditions of PSAARR were proposed.Third,a PSAARR synthesis method was proposed based on the screw theory and type of PSAARR synthesis conducted.Finally,an HRCC kinematic model was established to verify the self-alignment capability of the PSAARR.In this study,93 types of PSAARR limb structures were synthesized and the self-alignment capability of a human-robot joint axis was verified through kinematic analysis,which provides a theoretical basis for the design of such an ARR.

Analysis of dynamic characteristics of self-aligning ball bearing

A dynamics model of the self-aligning ball bearing is proposed based on the Jones-Harris method （JHM）, and a computer program is developed to solve the equations by using the Newton-Raphson method. A parametric analysis of the centrifugal force and the gyroscopic moment, the contact loads, the contact angles, the radial deformation and the radial stiffness is carried out. The analytical results show that the applied loads and the rotational speed are two main factors that can influence the distributions of the contact loads and values of the contact angles. The centrifugal force and the gyroscopic moment increase with the increase in the rotational speed, resulting in the decrease of the inner raceway contact load and the increase of the outer raceway contact load. The outer raceway contact angle increases under the centrifugal force; on the contrary, the inner raceway contact angle decreases. Furthermore, the differences between the inner and the outer contact angles increase with the increase in the rotational speed. The higher rotational speed results in the decrease in radial stiffness for the self-aligning ball bearing, and the raceway curvature coefficient, to some extent, also influences the radial stiffness.

Self-alignment of full skewed RSINS: observability analysis and full-observable Kalman filter

Traditional orthogonal strapdown inertial navigation sys-tem （SINS） cannot achieve satisfactory self-alignment accuracy in the stationary base： taking more than 5 minutes and al the iner-tial sensors biases cannot get ful observability except the up-axis accelerometer. However, the ful skewed redundant SINS （RSINS） can not only enhance the reliability of the system, but also improve the accuracy of the system, such as the initial alignment. Firstly, the observability of the system state includes attitude errors and al the inertial sensors biases are analyzed with the global perspective method： any three gyroscopes and three accelerometers can be assembled into an independent subordinate SINS （sub-SINS）;the system state can be uniquely confirmed by the coupling connec-tions of al the sub-SINSs;the attitude errors and random constant biases of al the inertial sensors are observable. However, the ran-dom noises of the inertial sensors are not taken into account in the above analyzing process. Secondly, the ful-observable Kalman filter which can be applied to the actual RSINS containing random noises is established; the system state includes the position, ve-locity, attitude errors of al the sub-SINSs and the random constant biases of the redundant inertial sensors. At last, the initial self-alignment process of a typical four-redundancy ful skewed RSINS is simulated： the horizontal attitudes （pitch, rol ） errors and yaw error can be exactly evaluated within 80 s and 100 s respectively, while the random constant biases of gyroscopes and accelero-meters can be precisely evaluated within 120 s. For the ful skewed RSINS, the self-alignment accuracy is greatly improved, mean-while the self-alignment time is widely shortened.

高超声速飞行器减阻杆-双盘-槽道组合构型减阻防热特性研究

针对高超声速飞行器减阻防热问题,提出了一种减阻杆头部开槽进气、中部侧向排气的减阻杆-双盘-槽道组合构型。在飞行高度30 km、来流马赫数6条件下,基于SST k-ω湍流模型,采用有限体积法求解了二维轴对称雷诺平均N-S方程,对组合构型的流场进行了数值模拟,并分析了其减阻防热特性。相比减阻杆-单盘构型,减阻杆-双盘构型减阻防热效果更好,而减阻杆-双盘-槽道构型可以进一步提高减阻防热效果。进行了组合构型的影响因素分析,数值仿真结果表明,在研究参数范围内,侧向排气孔靠近两个气动盘中间位置、第二个气动盘直径较大的构型减阻防热总体效果较好。相比减阻杆-单盘构型,较优构型的总阻力系数降低了24.70%,钝体壁面斯坦顿数峰值降低了53.63%。

980nm Oxide-Confined Vertical Cavity Surface Emitting Laser

Top-emitting oxide-confined intra-cavity contact structure 980nm VCSEL is fabricated by low-pressure metal organic chemical-vapor deposition (LP-MOCVD).Self-aligning etching process and selective oxidation are applied for current confinement.Output light power of 10.1mW and slope efficiency of 0.462mW/mA are obtained under room temperature,pulse operation,and injection current of 28mA.The maximum light power is 13.1mW under pulse operation.Output light power of 7.1mW,lasing wavelength of 974nm,and FWHM of 0.6nm are obtained under CW condition.The study of oxide-aperture influence on threshold current and differential resistance shows that lower threshold current can be obtained with a smaller oxide-aperture diameter.

带双气动盘的气动杆构型减阻防热性能研究

采用计算流体力学数值方法研究了带气动盘的气动杆对高超声速钝头体气动阻力和气动加热的影响,空间离散采用AUSM+格式,湍流模拟采用Menter's SST k-ω模型。结果表明带双气动盘的气动杆具有最佳的减阻防热性能,且其通过流场重构的方法实现了钝头体的减阻和防热。此外增加双气动盘之间的距离对钝头体的减阻防热性能不利,在进行气动杆设计时应尽量减小两个气动盘的距离。

InP/InGaAs Heterojunction Bipolar Transistor with Base μ-Bridge and Emitter Air-Bridge

An InP-based single-heterojunction bipolar transistor （SHBT） with base μ-bndge and emitter air-bridge is reported. Because those bridges reduce parasitic capacitance greatly, the cutoff frequency fT of the 2μm ×12.5μm InP SHBT without de-embedding reaches 178GHz. It is critical in high-speed low power applications,such as OEIC receivers and analog-to-digital converters.

气动盘对气动杆模型减阻效率的影响

为了降低高超声速钝头体的气动阻力,采用CFD数值方法研究了气动盘对气动杆减阻效率的影响。结果表明安装气动盘时钝头体前方回流区增大,钝头体压强峰值的位置向后移动,且模型阻力系数得到了有效降低。随后在此基础上研究了气动盘形状对减阻效率的影响。结果表明平面盘比尖锥形和半球形气动盘具有更佳的减阻效率,且平面盘还具有易加工制造的优点。

Self-aligned graphene field-effect transistors on SiC(0001) substrates with self-oxidized gate dielectric

A scalable self-aligned approach is employed to fabricate monolayer graphene field-effect transistors on semi-insulated 4H-SiC （0001） substrates. The self-aligned process minimized access resistance and parasitic capacitance. Self-oxidized Al2O3, formed by deposition of 2 nm A1 followed by exposure in air to be oxidized, is used as gate dielectric and shows excellent insulation. An intrinsic cutoff frequency of 34 GHz and maximum oscillation frequency of 36.4 GHz are realized for the monolayer graphene field-effect transistor with a gate length of 0.2 μm. These studies show a pathway to fabricate graphene transistors for future applications in ultra-high frequency circuits.

High quality metal-quantum dot-metal structure fabricated with a highly compatible self-aligned process

A self-aligned process to fabricate a ＂metal-quantum dot-metal＂ structure is presented, based on an ＂electron beam lithography, thin film deposition and dry etching process＂. The sacrificial layers used can improve the lift-off process, and novel lithography layouts design can improve the mechanical strength of the fabricated nanostructures. The superiority of the self-aligned process includes low request for overlay accuracy, high compatibility with a variety of materials, and applicable to similar structure devices fabrication. Finally, a phase change memory with fully confined phase-change material node, with the length × width × height of 255 × 45 × 30 nm^3 was demonstrated.

A Photolithography Process Design for 5 nm Logic Process Flow

With the introduction of EUV lithography,the photolithographic process in 5 nm logic process can be simplified to use mostly single exposure method.In a typical 5 nm logic process,the contact-poly pitch(CPP)is 44-50 nm,the minimum metal pitch(MPP)is around 30-32 nm.And the overlay budget is estimated to be 2.5 nm(on product overlay).Although the optical resolution of a 0.33NA exposure tool(such as ASML NXE3400)can reach below 32 nm pitch,stochastics in the EUV absorption in photoresists has limited its application to smaller pitches.For the CPP mentioned above,one can use 193 nm immersion lithography with Self-Aligned Double Patterning(SADP)technique to provide good image contrast(or CDU,LWR)as well as good overlay,as for the 10 and 7 nm generations.In the BEOL,however,the 30-32 pitch cannot be realized by a single EUV exposure with enough printing defect process window.If this pitch is to be done by 193 nm immersion lithography,more than 6-8 exposures are needed with very complicated overlay result.For EUV,this can be done through self-aligned LELE with both good CD and overlay control.We have done an optimization of the photolithographic process parameters for the typical metal with a self-developed aerial image simulator based on rigorous coupled wave analysis(RCWA)algorithm and the Abbe imaging routine with an EUV absorption model which describes stochastics.We have calibrated our model with wafer exposure data from several photoresists under collaboration with IMEC.As we have presented last year,to accommodate all pitches under a logic design rule,as well as to provide enough CDU for the logic device performance,in DUV lithography,a typical minimum exposure latitude(EL)for the poly and metal layers can be set at,respectively,18%and 13%.In EUV,due to the existence of stochastics,13%EL,which corresponds to an imaging contrast of 40%,seems not enough for the metal trenches,and to obtain an imaging contrast close to 100%,which yields an EL of 31.4%means that we need to relax minimum pitch to above 41 nm(conventional imaging limit for 0.33NA).This is the best imaging contrast a photolithographic process can provide to reduce LWR and stochastics.In EUV,due to the significantly smaller numerical apertures compared to DUV,the aberration impact can cause much more pronounced image registration error,in order to satisfy 2.5 nm total overlay,the aberration induced shift needs to be kept under 0.2 nm.We have also studied shadowing effect and mask 3D scattering effect and our results will be provided for discussion.