Friction Characteristics Between Marine Clay and Construction Materials

Structure-soil interface friction characteristics is of importance to investigate the interaction between engineering structures and soils,especially for offshore structures.The interface friction behavior between marine clay and structural materials with different roughness was studied in this paper by using 3D optical scanning tests,a modified direct shear device and numerical simulation.Relationships between the surface roughness of structures,water content and interface friction angle were presented by model tests.The increase of water contents decreased the interface friction angles.For interfaces with different roughness,the interface friction angles will be smaller than that of the soil when the water content exceeds a certain value.The roughness of the interface and the water content of the soil are mutually coupled to influence the coefficient of friction(COF).This paper proposed a Finite Element Method(FEM)to simulate the interface direct shear tests of structures with different roughness.The surface models with different roughness are established based on the structure data obtained by 3D scanning.The Coupled Eulerian-Lagrangian(CEL)approach was employed to analyse soils sheared by irregular surfaces.The interface behavior for interfaces with different roughness under cyclic shear stresses was analyzed by FEM.

Existence and numerical approximation of a solution to frictional contact problem for electro-elastic materials

In this paper,a frictional contact problem between an electro-elastic body and an electrically conductive foundation is studied.The contact is modeled by normal compliance with finite penetration and a version of Coulomb’s law of dry friction in which the coefficient of friction depends on the slip.In addition,the effects of the electrical conductivity of the foundation are taken into account.This model leads to a coupled system of the quasi-variational inequality of the elliptic type for the displacement and the nonlinear variational equation for the electric potential.The existence of a weak solution is proved by using an abstract result for elliptic variational inequalities and a fixed point argument.Then,a finite element approximation of the problem is presented.Under some regularity conditions,an optimal order error estimate of the approximate solution is derived.Finally,a successive iteration technique is used to solve the problem numerically and a convergence result is established.

Effects of copper-coated MoS_(2) on friction performance of bronze-graphite-MoS_(2) self-lubricating materials

Two kinds of bronze-graphite-MoS_(2) self-lubricating materials with copper-coated MoS_(2) and uncoated MoS_(2) were prepared by powder metallurgy.Friction and wear experiments were carried out under 4 N and 10 N loads respectively,and the effects of copper-coated MoS_(2) on the friction performances of the materials were studied.Results showed that the way of copper-coated on the surface of MoS_(2) could reinforce the bonding between MoS_(2) and matrix,and inhibited the formation of MoO_(2).Moreover,both materials formed a MoS_(2) lubricating film on the surface during the friction process.While the lubricating film formed after copper coating on MoS_(2) was thicker and had uneven morphology,it was more conducive to improving the friction performance of the material.Compared with conventional materials,the wear rate of copper-coated materials was reduced by one order of magnitude,and the friction coefficient was also reduced by 22.44% and 22.53%,respectively,when sliding under 4 N and 10 N loads.It shows that copper-coated MoS_(2)can improve friction properties of bronze-graphite-MoS_(2)self-lubricating materials furtherly.

Copper-Free Resin-Based Braking Materials:A New Approach for Substituting Copper with Fly-Ash Cenospheres in Composites

Copper particles emitted from braking have become a significant source of environmental pollution.However,copper plays a crucial role in resin-based braking materials.Developing high-performance braking materials without copper has become a significant challenge.In this paper,the resin-based braking materials were filled with flyash cenospheres to develop copper-free braking materials.The effects of fly-ash cenospheres on the physical properties,mechanical and friction and wear properties of braking materials were studied.Furthermore,the wear mechanism of copper-free resin-based braking materials filled with fly-ash cenospheres was discussed.The results indicate that the inclusion of fly-ash cenospheres in the braking materials improved their thermal stability,hardness and impact strength,reduced their density,effectively increased the friction coefficient at medium and high temperatures,and enhanced the heat-fade resistance of the braking materials.The inclusion of fly-ash cenospheres contributed to the formation of surface friction film during the friction process of the braking materials,and facilitated the transition of form from abrasive wear to adhesive wear.At 100-350℃,the friction coefficient of the optimal formulation is in the range of 0.57-0.61,and the wear rate is in the range(0.29-0.65)×10^(-7) cm^(3)·N^(-1)·m^(-1),demonstrating excellent resistance to heat-fade and stability in friction coefficient.This research proposes the use of fly-ash cenospheres as a substitute for environmentally harmful and expensive copper in brake materials,which not only improves the performance of braking materials but also reduces their costs.

3D modeling for effect of tool eccentricity on coupled thermal and material flow characteristics during friction stir welding

A novel three-dimensional numerical model is proposed to investigate the effect of tool eccentricity on the coupled thermal and material flow characteristics in friction stir welding(FSW) process.An asymmetrical boundary condition at the tool-workpiece interface,and the dynamic mesh technique are both employed for the consideration of the tool eccentricity during tool rotating.It is found that tool eccentricity induces the periodical variation of the heat densities both at the tool-workpiece interface and inside the shear layer,but the fluctuation amplitudes of the heat density variations are limited.However,it is demonstrated that tool eccentricity results in significant variation of the material flow behavior in one tool rotating period.Moreover,the material velocity variation at the retreating side is particularly important for the formation of the periodic characteristics in FSW.The modeling result is found to be in good agreement with the experimental one.

Tribological Properties of Self-lubricating Laminated Ceramic Materials

In order to improve the tribological properties of ceramic composites, Al2O3/TiC-Al2O3/ TiC/CaF2 self-lubricating laminated ceramic composites were prepared by vacuum hot pressing sintering. Experiments were conducted to get mechanical properties and the friction and wear properties were also measured with friction and wear tester. The worn surfaces were observed by scanning electron microscope （SEM） and energy dispersion spectrum （EDS）. The wear resistance properties and the self-lubricating effect of ceramic composites were analyzed. Results show that the Al2O3/TiC-Al2O3/TiC/CaF2 self-lubricating laminated ceramic composites layers are well-defined with a higher bonding strength and the mechanical performances are uniform enough to overcome the anisotropy of weak laminated ceramic composites. In addition, the fracture toughness of Al2O3/TiC layers is also improved. Its friction coefficient and wear rates decrease with the increase of rotation speed and load. Al2O3/TiC-Al2O3/TiC/CaF2 self-lubricating laminated ceramic composites have good wear resistance because of the tribofilm formed by the CaF2 solid lubricants. The wear mechanisms of Al2O3/TiC/ CaF2 layers are abrasive wear and Al2O3/TiC layers are adhesive wear.

Effects of Friction Heat on the Tribological Properties of the Woven Self-lubricating Liner

In the dry-sliding process of the woven self-lubricating liner which is used in the self-lubricating spherical plain bearing, the friction heat plays an important role in the tribological performances of the liner. It has important value to study on the relationship between tribological performances of the liner and the friction heat. Unforttmately, up to now, published work on this relationship is quite scarce. Therefore, the effect of friction heat on the tribological performances of the liner was investigated in the present work. The tribological behaviors of the liner were evaluated by using the high temperature end surface wear tester. Scanning electron microscopy （SEM） was utilized to examine the morphologies of worn surfaces of the liner and study the failure modes. Differential scanning calorimetry （DSC） measurement and X-ray diffraction （XRD） analysis were performed to study the behaviors of the wear debris. The temperature rise on the worn surface was calculated according to classical models. SEM observation shows that the dominating wear mechanism for the liner is mainly affected by friction shear force, contact pressure and friction heat. Higher fusion heat for the wear debris than that for the pure polytetrafluroethylene （PTFE） indicates that the PTFE is the main portion of the wear debris, and, the PTFE in the wear debris shows a higher crystallisation degree owing to the effects of friction shear force and the friction heat. Combining the calculated temperature rise results with the wear rate of the liner, it can be concluded that the effects of temperature rise o n the tribological performances of the liner become more obvious when the temperature rise exceeds the glass transition temperature （Tg） of the PTFE. The wear resistance of the liner deteriorates dramatically when the temperature rise approaches to the melting point （Ton） of the PTFE. The tribological performances of the liner can be improved when the temperature rise exceeds Tg but is far lower than Ton- The present study on the relationship between the temperature rise and the tribological performances of the liner may provide the basis for further understanding of the wear mechanisms of the liner as well as the relationship between the formation of the PTFE transfer film and the friction heat during the dry-sliding of the Finer.

Low-cost solid FeS lubricant as a possible alternative to MoS2 for producing Fe-based friction materials

Three reaction systems of MoS_2-Fe, FeS -Fe, and Fe S-Fe-Mo were designed to investigate the use of FeS as an alternative to MoS_2 for producing Fe-based friction materials. Samples were prepared by powder metallurgy, and their phase compositions, microstructures, mechanical properties, and friction performance were characterized. The results showed that MoS_2 reacts with the matrix to produce iron-sulfides and Mo when sintered at 1050°C. Iron-sulfides produced in the MoS_2-Fe system were distributed uniformly and continuously in the matrix, leading to optimal mechanical properties and the lowest coefficient of friction among the systems studied. The lubricity observed was hypothesized to originate from the iron-sulfides produced. The Fe S-Fe-Mo system showed a phase composition, porosity, and density similar to those of the MoS_2-Fe system, but an uneven distribution of iron-sulfides and Mo in this system resulted in less-optimal mechanical properties. Finally, the Fe S-Fe system showed the poorest mechanical properties among the systems studied because of the lack of Mo reinforcement. In friction tests, the formation of a sulfide layer contributed to a decrease in coefficient of friction（COF） in all of the samples.

The Friction and Wear Properties of the Spherical Plain Bearings with Self-lubricating Composite Liner in Oscillatory Movement

A test method based on the condition simulation and a friction and wear test machine featuring in oscillatory movement were set up for self-lubricating spherical plain bearings (SPB). In the machine the condition parameters such as load, angle and frequency of oscillation and number of test cycles can be properly controlled. The data relating to the tribological properties of the bearing, in terms of friction coefficient, linear wear amount, temperature near friction surface and applied load, can be monitored and recorded simultaneously during test process by a computerized measuring system of the machine. Efforts were made to improve the measurement technology of the friction coefficient in oscillating motion. In result, a well-designed bearing torque mechanism was developed, which could reveal the relation between the friction coefficient and the displacement of oscillating angle in any defined cycle while the curve of friction coefficient vs number of testing cycles was continuously plotted. The tribological properties and service life of four kinds of the bearings, i.e, the sampleⅠ-Ⅳ with different self-lubricating composite liners, including three kinds of polytetrafluoroethylene (PTFE) fiber weave/epoxy resin composite liners and a PTFE plastic/copper grid composite liner, were evaluated by testing, and the wear mechanisms of the liner materials were analyzed.

Materials flow and phase transformation in friction stir welding of Al 6013/Mg

Material flow and phase transformation were studied at the interface of dissimilar joint between Al 6013 and Mg, produced by stir friction welding （FSW） experiments. Defect-free weld was obtained when aluminum and magnesium were placed in the advancing side and retreating side respectively and the tool was placed 1 mm off the weld centerline into the aluminum side. In order to understand the material flow during FSW, steel shots were implanted as indexes into the welding path. After welding, using X-ray images, secondary positions of the steel shots were evaluated. It was revealed that steel shots implanted in advancing side were penetrated from the advancing side into the retreating side, whereas the shots implanted in the retreating side remained in the retreating side, without penetrating into the advancing side. The welded specimens were also heat treated. The effects of heat treatment on the mechanical properties of the welds and the formation of new intermetallic layers were investigated. Two intermetallic compounds, Al3Mg2 and Al12Mg17, were formed sequentially at Al6013/Mg interface.

Solid FeS lubricant: a possible alternative to MoS2 for Cu–Fe-based friction materials

Molybdenum disulfide(MoS_2) is one of the most commonly used solid lubricants for Cu–Fe-based friction materials. Nevertheless, MoS_2 reacts with metal matrices to produce metal sulfides(e.g., FeS) and Mo during sintering, and the lubricity of the composite may be related to the generation of FeS. Herein, the use of FeS as an alternative to MoS_2 for producing Cu–Fe-based friction materials was investigated. According to the reaction principle of thermodynamics, two composites—one with MoS_2(Fe–Cu–MoS_2 sample) and the other with FeS(FeS–Cu_2S–Cu–Fe–Mo sample), were prepared and their friction behaviors and mechanical properties were compared. The results showed that MoS_2 reacted with the Cu–Fe matrix to produce FeS, metallic ternary sulfides, and Mo when sintered at 1050°C. The MoS_2–Cu–Fe and FeS–Cu_2S–Cu–Fe–Mo samples thereby exhibited similar characteristics with respect to phase composition, density, hardness, and tribological behaviors. Micrographs of the worn surfaces revealed that the stable friction regime for both composites stemmed from the iron sulfides friction layers rather than from the molybdenum sulfides layers.

Analysis of a quasistatic contact problem with adhesion and nonlocal friction for viscoelastic materials

A mathematical model is established to describe a contact problem between a deformable body and a foundation. The contact is bilateral and modelled with a nonlocal friction law, in which adhesion is taken into account. Evolution of the bonding field is described by a first-order differential equation. The materials behavior is modelled with a nonlinear viscoelastic constitutive law. A variational formulation of the mechanical problem is derived, and the existence and uniqueness of the weak solution can be proven if the coefficient of friction is sufficiently small. The proof is based on arguments of time-dependent variational inequalities, differential equations, and the Banach fixed-point theorem.

Impact and Friction Sensitivity of Energetic Materials：Methodical Evaluation of Technological Safety Features

Key methods developed and used in the USSR and in the Russian Federation to determine the impact and friction sensitivity of energetic materials and explosives have been discussed.Experimental methodologies and instruments that underlie the assessment of their production and handling safety have been described.Studies of a large number of compounds have revealed relationships between their sensitivity parameters and structure of individual compounds and compositions.The range of change of physical and chemical characteristics for the compounds we examined covers the entire region of their existence.Theoretical methodology and equations have been formulated to estimate the impact and friction sensitivity parameters of energetic materials and to evaluate the technological safety in use.The developed methodology is characterized by high-accuracy calculations and prediction of sensitivity parameters.

Effect of ZrSiO_4 on the Friction Performance of Automotive Brake Friction Materials

Friction-wear properties of the ZrSiO4 reinforced samples were measured and compared with those of plain bronze based ones. For this purpose, density, hardness, friction coefficient wear behaviour of the samples were tested. Microstructures of samples before and after sintering and worn surfaces were also investigated by scanning electron microscopy （SEM）, and the wear types were determined. The optimum friction-wear behaviour was obtained in the sample compacted at 500 MPa and sintered at 820℃. Density of the final samples decreased with increasing the amount of reinforcing elements （ZrSiO4） before pre-sintering. However after sintering, there is no change in density of the samples including reinforcing elements （ZrSiO4）. With increasing friction surface temperature, a reduction in the friction coefficient of the samples was observed. However, the highest reductions in the friction coefficients were observed in the as-received samples containing 0. 5% reinforced ZrSiO4. The SEM images of the sample indicated that while bronze-based break lining material without ZrSiO4 showed abrasive wear behaviour, increasing the amount of ZrSiO4 resulted a change in abrasive to adhesive wear mechanism. All samples exhibited friction-wear values, which were within the values shown in SAE-J661 standard. With increasing the amount of reinforcing ZrSiO4, wear resistance of the samples was increased. However samples reinforced with 5% and 6% ZrSiO4 showed the best results.

The Dynamic Tribological Performance of One Certain Resin-based Friction Materials under Different Temperature Conditions

A fixed-point observation method was designed to research the dynamic tribological performance of one certain resin-based friction materials. The friction test was performed through a constant speed friction tester under various temperature conditions. It was found that the dynamic tribological performance of materials has a good consistency with the dynamic evolution of worn surfaces. At lower temperatures, the friction coefficient and wear rate were constant, resulted from the stable worn surfaces. At higher temperatures, the friction coefficient increased gradually, while the wear rate decreased, due to the increasing contact area and Fe concentration. A fade occurred above 250 ℃, which can be explained by the degradation of binders.

Microstructure and frictional properties of 3D needled C/SiC brake materials modified with graphite

The 3D needled C/SiC brake materials modified with graphite were prepared by a combined process of the chemical vapor infiltration,slurry infiltration and liquid silicon infiltration process.The microstructure and frictional properties of the brake materials were investigated.The density and open porosity of the materials as-received were about(2.1±0.1)g/cm3and(5±1)%,respectively.The brake materials were composed of 59%C,39%SiC,and 2%Si(mass fraction).The content of Si in the C/SiC brake materials modified with graphite was far less than that in the C/SiC brake materials without being modified with graphite,and the Si was dispersed.The braking curve of the 3D needled C/SiC modified with graphite was smooth,which can ensure the smooth and comfortable braking.The frictional properties under wet condition of the 3D needled C/SiC modified with graphite showed no fading.And the linear wear rate of the C/SiC modified with graphite was lower than that of the C/SiC unmodified.

Effect of zinc powder content on tribological behaviors of brake friction materials

Brake friction materials with different zinc powder contents(0,2,4,6,8 wt.%)were fabricated via powder metallurgy method.The results indicate that with the increasing zinc powder content,the density and thermal conductivity of the materials gradually increase,while the hardness decreases monotonously.With increasing zinc powder content,the curve of the nominal friction coefficient shows fluctuating trend but the lowest friction coefficient also shows an increase.However,the wear rate and braking noise of the friction material monotonously decrease with increasing zinc content.This effect may be attributed to the transformation of the tribological mechanism from adhesive wear and abrasive wear to adhesive wear.The brake friction material with 4 wt.%zinc powder exhibits both the best tribological and noise performance.

Effect of Friction Reclaimed Materials of Waste Brake-shoe on Basic Performance of Mortar

Discarded train brake shoes mainly consist of steel-backed friction material. To be better reutilized, its essential features and its interaction in cement-based material need to be studied. Consequently, particle size analysis, SEM, IR and TGA were used to investigate two types of waste brake shoes, i e, mechanical grinding friction reclaimed material of waste brake-shoe（G-FRMWBS） and pyrolysis-friction reclaimed materials of waste brake-shoe（P-FRMWBS）. The latter exhibited less organic content, larger range of particle size distribution and smaller medium particle diameter. Both types contained inorganic particles of spherical and irregular shapes, striped with steel fiber. Upon isometric substituting fine aggregates, G-FRMWBS lifted the strength of mortar effectively that was increased by 16.6% and 17.5% when the replacing rate was 5%; the value went up to 19.2% and 19.2% when the replacing rate was 10%. Moreover, inclusion of FRMWBS enhanced the chloride penetration resistance, and optimized the pore characteristic and ITZ（interfacial transition zone） as well.

Frictionally excited thermoelastic dynamic instability of functionally graded materials

The perturbation method is applied to investigate the frictionally excited thermoelastic dynamic instability (TEDI) of a functionally graded material (FGM) coating in half-plane sliding against a homogeneous half-plane. We assume that the thermoelastic properties of the FGM vary exponentially with thickness. We also examine the effects of the gradient index, sliding speed, and friction coefficient on the TEDI for various material combinations. The transverse normal stress for two different coating structures is calculated. Furthermore, the frictional sliding stability of two different coating structures is analyzed. The obtained results show that use of FGM coatings can improve the TEDI of this sliding system and reduce the possibility of interfacial failure by controlling the interfacial tensile stress.

Development of processing windows for friction stir spot welding of aluminium Al5052/copper C27200 dissimilar materials

Friction stir spot welding technique was used to join dissimilar combinations of aluminium alloy(Al5052)with copperalloy(C27200)and friction stir spot welding windows such as tool rotational speed–dwell time and tool rotational speed?plungedepth diagrams for effective joining of these materials were developed.Using a central composite design model,empirical relationswere developed to predict the changes in tensile shear failure load values and interface hardness of the joints with three processparameters such as tool rotational speed,plunge depth and dwell time.The adequacy of the developed model was verified usingANOVA analysis at95%confidence level.Response surface methodology was used to optimize the developed model to maximizetensile strength and minimize interface hardness.A high tensile shear failure load value of3850N and low interface hardness valueof HV81was observed for joints made under optimum conditions,and validation experiments confirmed the high predictability ofthe developed model with error less than2%.The operating windows developed shall act as reference maps for future designengineers in choosing appropriate friction stir spot welding process parameter values to obtain good joints.