ANALYSIS FOR AIRCRAFT TAXIING AT VARIABLE VELOCITY ON UNEVENNESS RUNWAY BY THE POWER SPECTRAL DENSITY METHOD

In this paper a novel approach for the analysis of non stationary response of aircraft landing gear taxiing over an unevenness runway at variable velocity is explored, which is based on the power spectral density method. A concerned analytical landing gear model for simulating actual aircraft taxiing is formulated. The equivalent linearization results obtained by probabilistic method are inducted to treat landing gear non linear parameters such as shock absorber air spring force, hydraulic damping and Coulomb friction, tire stiffness and damping. The power spectral density for non stationary analysis is obtained via variable substitution and then Fourier transform. A representative response quantity, the overload of the aircraft gravity center, is analyzed. The frequency response function of the gravity overload is derived. The case study demonstrates that under the same reached velocity the root mean square of the gravity acceleration response from constant acceleration taxiing is smaller than that from constant velocity taxiing and the root mean square of the gravity acceleration response from lower acceleration taxiing is greater than that from higher acceleration.

ESTIMATION OF THE NUMBER OF CORRELATED SOURCES WITH COMMON FREQUENCIES BASED ON POWER SPECTRAL DENSITY

Blind source separation and estimation of the number of sources usually demand that the number of sensors should be greater than or equal to that of the sources, which, however, is very difficult to satisfy for the complex systems. A new estimating method based on power spectral density （PSD） is presented. When the relation between the number of sensors and that of sources is unknown, the PSD matrix is first obtained by the ratio of PSD of the observation signals, and then the bound of the number of correlated sources with common frequencies can be estimated by comparing every column vector of PSD matrix. The effectiveness of the proposed method is verified by theoretical analysis and experiments, and the influence of noise on the estimation of number of source is simulated.

Four Years of Daily Photon Emissions That Have Predicted Major Earthquakes: Raw Data, Spectral Power Density Analyses and Implications for the Geosciences

The daily median ground surface flux densities per day from a continuously operating photomultiplier tube unit for four years in Sudbury, Ontario are presented for December 2010 to December 2014. Increases of about 2 to 4 PMT units (1 unit = 5 × 10-11 W·m-2) for median daily measures reliably occurred about two weeks before M ≥ 7.7 earthquakes anywhere on the planet. The PMT units, until June 2014, usually returned to baseline within a few days after the events. There has been a slow positive drift in flux power density since about 2012 and a conspicuous maintained increase after May, 2014. The equivalent energy per day if it were represented isotropically within the volume occupied by the earth is the same order of magnitude as the average daily global total seismic energy release. Spectral power densities revealed enhanced peaks (periodicities) between 100 to 150 days, 60 days, 30 days, and 25 days. Discriminable peaks in power were noted around 18 days, 14 days, and 4 to 6 days. These results suggest that continuous measurement of photonemissions within hyper-dark conditions may reveal geophysical processes that precede larger seismic events and could reflect the movement of the earth-solar system around the galactic center.

Roughness evaluation of three-dimensional asphalt pavement based on two-dimensional power spectral density

To solve the problem of the lack of comprehensive evaluation of three-dimensional(3D)asphalt pavement roughness,a method for evaluating the asphalt pavement roughness is proposed based on two-dimensional(2D)power spectral density(PSD).By calculating the 2D PSD of a 3D asphalt pavement and converting it into the longitudinal average asphalt pavement PSD,the relationship between the evaluation method of the 3D asphalt pavement roughness and the current evaluation standard of roughness is established.Combined with the road-fitting formula used in international standards,the elevation data of the A,B,C,and D grades of the 3D asphalt pavement are simulated by the harmonic superposition method.According to the proposed method,the longitudinal PSD of each level of simulated asphalt pavement is calculated and compared with the standard spectral line of each pavement level.This approach verifies the effectiveness of the proposed method in evaluating the roughness of the 3D asphalt pavement.Compared with the PSD of a certain horizontal profile elevation,it is verified that the fluctuation amplitude of the spectral line calculated by the proposed method is greatly improved.The results show that the proposed method can evaluate the roughness of asphalt pavements more comprehensively and accurately and has strong practicability.

EVALUATION OF POWER SPECTRAL DENSITY OF PASSIVE INTERMODULATION DISTORTION IN HIGH-POWER COMMUNICATION SATELLITE SYSTEMS

In order to analyze the deleterious effects of Passive InterModulation (PIM) on high power communication satellite systems, the basic concept of PIM is introduced, and an equation for the power spectral density of the n-th order PIM distortion insuch systems is derived by applying flat signal-power spectrum assumption and Fourier transform method. It is indicated that PIM level generally decreases with order and the lowest frequency receive channel in the receive band is the channel of most affected by PIM interference.

The Wavefront Power Spectral Density Measurement of Aspheric Lens with Long Focal-Length Using a Computer-Generated Hologram

To ensure the performance of the optical system, the machining accuracy of lens with long focal lengths is required to ensure the image quality. A new method for lens transmission wavefront power spectral density (PSD) in mid-frequency domain measurement using binary phase computer-generated hologram (CGH) is presented. This technique is widely applicable and is particularly useful for measuring large-size lenses with long focal lengths. A comparison experiment of the CGH measurement with results from a Fizeau sphere interferometry method is carried out to verify the accuracy and convenience of the measurement. Furthermore, measurement uncertainty due to CGH fabrication process is analysed. Analysis of the CGH test showed the overall accuracy of less than 1 nm RMS for a sphere lens with over 30 m focal length and Φ410 mm clear aperture. CGH can provide reference spheres with high precision, in the meantime greatly shorten air space, thus reducing the effect of vibration and air turbulence, therefore is of great importance for lens transmission wavefront PSD measurement. The realization of high precision, high efficiency and nondestructive testing of long focal-lens wavefront PSD ensure the ultra-precision and certainty level of machining, hence improving the comprehensive performance of the optical system.

High dynamic synchronization algorithm based on cyclic spectral density

A new high dynamic synchronization algorithm using cyclic spectral density was presented according to the theories of cyclic spectral density and its anti-interface and anti-noise properties.The closed forms of frequency error and phase error were obtained,and their performances were analyzed.The in-phase signal throw costas loop was normalized to obtain a cosine signal.Cyclic spectral density of the cosine signal of was computed to obtain the frequency error and the phase error and then results were put into NCO to synchronize.Finally,the performance of the presented algorithms was compared with the conventional algorithms by virtue of simulations,and the simulation results proved the correctness and the superiority of the new algorithms.

The Changes of Heart Rate Power Spectral Density during Head-up Tilt Test

To study the role of autonomic nervous system in the period of developing syncope induced by head-up tilt test(HUT), we analysed the changes of heart rate power spectral density(HRPSD) in 50 patients with unexplained syncope, including 15 positive patients (Group 1) and 35 negative patients(Group 2), and 15 negative healthy persons(Group 3) in 5 minute periods before and after tilting and 5 minutes before the end of test. HRPSD and their changes in total(T), very low-frequence(VLF), low-frequence(LF), high-frequence(HF) and the ratio of low/high frequence(LF/HF) were similar (P>0.05) 5 minutes before and after tilting among three groups. Five minutes before the end of test, Group 1 had obvious increase of T, VLF, LF and LF/HF while Group 2 and 3 had not such significant changes. There was significant difference(P<0.01) compared Group 1 with Group 2, 3. The results showed that the abnormal regulatory function of autonomic nervous system played an important role in the mechanism of symcope induced by HUT, the positive group had abnormal increase of sympathetic tone and imbalance of sympathetic/parasympathetic neural tone before syncope appeared.

Degradation of effective carrier-power-to-noise densityratio based on code trackingspectral sensitivitycoefficient for GNSS radio frequencycompatibilityin C band

The frequency band between 5 010 MHz and 5 030 MHz allocated as C band has been used as a candidate in the global navigation satellite systems （GNSS） along with more and more naviga- tion services in L band. The potential benefits and technical requirements of C band for satellite navi- gation have been analyzed before. However the degradation of effective carrier-power-to-noise densi- ty ratio（ A （C/No ）eu） based on code tracking spectral sensitivity coefficient（ CT_SSC ） as a compati- bility assessment methodology for potential GNSS radio frequency compatibility in C-Band has not been discussed clearly. So the compatibility of the signals in the C band between BeiDou （BD） B1 C and GPS L1C, L1C/A, Galileo E1Os as the interoperability or classical signals in L band is analyzed. Simulation results reveal the interference degree between BD III B1C and GPS L1C/A, L1C, Galileo E1OS. The results can also reveal that the multiplexed binary offset carrier （MBOC） and binary phase shift keying （BPSK） modulation is not appropriate for C band.

Non-Markovian dynamics of two non-coupled qubits interacting with two separate reservoirs with different spectral densities

The dynamics of two non-coupled qubits independently interacting with their reservoirs is solved by the time convolutionless projection operator method. We study two-qubit quantum correlation dynamics for two different types of spectral densities, which are a Lorentzian distribution and an Ohmic spectral density with a Lorentzian–Drude cutoff function. For two qubits initially prepared in the initial Bell state, quantum discord can keep longer time and reach larger values in nonMarkovian reservoirs for the first spectral distribution or by reducing the cutoff frequency for the second case. For the initial Bell-like state, the dynamic behaviors of quantum discord and entanglement are compared. The results show that a long time of quantum correlation can be obtained by adjusting some parameters in experiment and further confirm that the discord can capture quantum correlation in addition to entanglement.

Variation of electron density in spectral broadening process in solid thin plates at 400 nm

The generation of continuous spectrum centered at 400 nm from solid thin plates is demonstrated in this work.A continuum covering 365 nm to 445 nm is obtained when 125-µJ frequency-doubled Ti:sapphire laser pulses are applied to six thin fused silica plates at 1-kHz repetition rate.The generalized nonlinear Schrodinger equation simplified for forward propagation is solved numerically,the spectral broadening with the experimental parameters is simulated,and good agreement between simulated result and experimental measurement is achieved.The variation of electron density in the thin plate and the advantage of a low electron density in the spectral broadening process are discussed.

Porosity Evaluation and the Power Spectral Densities Analyses of Carbon-Nickel Composite Films Annealed at Different Temperatures

The densification and the fractal dimensions of carbon-nickel films annealed at different temperatures 300, 500, 800, and 1000℃ with emphasis on porosity evaluation are investigated. For this purpose, the refractive index of films is determined from transmittance spectra. Three different regimes are identified, T 〈 500℃, 500℃ 〈 T 〈 800℃ and T 〉 800℃. The Rutherford baekscattering spectra show that with increasing the annealing temperature, the concentration of nickel atoms into films decreases. It is shown that the effect of annealing temperatures for increasing films densification at T 〈 500℃ and T 〉 800℃ is greater than the effect of nickel concentrations. It is observed that the effect of decreasing nickel atoms into films at 500℃ 〈 T 〈 800℃ strongly causes improving porosity and decreasing densification. The fractal dimensions of carbon-nickel films annealed from 300 to 500℃ are increased, while from 500 to 1000℃ these characteristics are decreased. It can be seen that at 800℃, films have maximum values of porosity and roughness.

Spectral Density Estimation of Continuous Time Series

This paper studies spectral density estimation of a strictly stationary r-vector valued continuous time series including missing observations. The finite Fourier transform is constructed in L-joint segments of observations. The modified periodogram is defined and smoothed to estimate the spectral density matrix. We explore the properties of the proposed estimator. Asymptotic distribution is discussed.

Nonlinear distortion analysis for multisine excitation constrained by power spectral density

Nonlinear distortion introduced by an amplifier when subjected to a multisine excitation decreases the measurement accuracy in many metrological and measurement areas. In this paper, we performed qualitative and quantitative analyses of the nonlinear distortion with the multisine excitations constrained by a constant power spectral density. We present the numerical results with respect to different tone spacings,nonlinear orders, harmonic phases and tone distributions. Moreover, three as-pects of contributions are made to further reveal the distortion mechanism. First, we find that the type Ⅱ components for Schr- oeder-phase multisines distribute uniformly but not all in anti-phase to the type I components for the second order nonlinearity. Second,we simulate the variance of the type I and Ⅱ components and their summation to explain the principle of reducing the type Ⅱ distortion by averaging the results obtained using multiple realizations of random-phase multisines. Third, we observe a special distortion distribution mechanism for the Schroeder-phase multisine excitation The results contribute to a better estima-tion and understanding of the nonlinear distortion.

A self-powered solar-blind UV-enhanced Bi_(2)Se_(3)/a-Ga_(2)O_(3)/p-Si heterojunction photodetector for full spectral photoresponse and imaging

Self-powered full-spectrum photodetectors(PDs)offer numerous advantages,such as broad application fields,high precision,efficiency,and multi-functionality,which represent a highly promising and potentially valuable class of detectors for future development.However,insensitive response to solar-blind ultraviolet(UV)and complex and expensive preparation processes greatly limit their performance and practical application.In this study,a self-powered full-spectrum Bi_(2)Se_(3)/a-Ga_(2)O_(3)/p-Si heterojunction PD with high sensitivity for solar-blind UV band prepared by a simple and low-cost two-step synthesis method is presented.Experiments results reveal that the developed PD has an excellent performance,such as high sensitivity from 200 to 850 nm,and a responsivity of 1.38 mA/W as well as a detectivity of 3.22×10^(10) Jones under 254 nm light at zero bias.Additionally,the unencapsulated device displays exceptional stability and imaging capabilities.It is expected that Bi_(2)Se_(3)/a-Ga_(2)O_(3)/p-Si heterojunction PD with a simple and low-cost synthesis method has great potential for self-powered full-spectrum photodetectors.

Spectral computed tomography in advanced gastric cancer: Can iodine concentration non-invasively assess angiogenesis?

AIM To investigate the correlation of iodine concentration(IC) generated by spectral computed tomography(CT) with micro-vessel density(MVD) and vascular endothelial growth factor(VEGF) expression in patients with advanced gastric carcinoma(GC).METHODS Thirty-four advanced GC patients underwent abdominal enhanced CT in the gemstone spectral imaging mode. The IC of the primary lesion in the arterial phase(AP) and venous phase(VP) were measured, and were then normalized against that in the aorta to provide the normalized IC(nI C). MVD and VEGF were detected by immunohistochemical assays, using CD34 and VEGF-A antibodies, respectively. Correlations of nI C with MVD, VEGF, and clinical-pathological features were analyzed.RESULTS Both nI Cs correlated linearly with MVD and were higher in the primary lesion site than in the normal control site, but were not correlated with VEGF expression. After stratification by clinical-pathological subtypes, nI C-AP showed a statistically significant correlation with MVD, particularly in the group with tumors at stage T4, without nodular involvement, of a mixed Lauren type, where the tumor was located at the antrum site, and occurred in female individuals. nI C-VP showed a positive correlation with MVD in the group with the tumor at stage T4 and above, had nodular involvement, was poorly differentiated, was located at the pylorus site, of a mixed and diffused Lauren subtype, and occurred in male individuals. nI C-AP and nI C-VP showed significant differences in terms of histological differentiation and Lauren subtype.CONCLUSION The IC detected by spectral CT correlated with the MVD. n IC-AP and n IC-VP can reflect angiogenesis in different pathological subgroups of advanced GC.

Cross-spectral recognition method of bridge deck aerodynamic admittance function

This study proposes a new identification algorithm about the admittance function, which can estimate the full set of six aerodynamic admittance functions considering cross power spectral density functions about the forces and the turbulence components. The method was first numerically validated through Monte Carlo simulations, and then adopted to estimate the aerodynamic admittance of a streamlined bridge deck. The identification method was further validated through a comparison between the numerical calculation and wind tunnel tests on a moving bridge section. © 2015, Institute of Engineering Mechanics, China Earthquake Administration and Springer-Verlag Berlin Heidelberg.

Intensities and shifts of Lyman and Balmer lines of hydrogen-like ions in high density plasmas

The spectral line intensities and line shifts of Lyman and Balmer series for transitions up to n=5 of hydrogen-like ion are studied in plasmas with densities and temperatures in the ranges n_(c)~10^(18)-10^(21)cm^(-3),T_(e)=0.3e1.2 eV respectively.The screened potential used to describe the interaction between charged particles includes the electron exchange-correlation and finite-temperature gradient effects and is valid for both weakly and strongly coupled plasmas.The dependencies of alpha,beta and gamma line shifts of Lyman and Balmer series on plasma density(for fixed temperature)and temperature(for fixed density)are investigated.The results for the H_(a)line shifts are compared with the available high-density experimental data.

Spectral diagnostics of complex arc plasma

A spectral diagnostics of complex are plasma using multiple spectral information of arc self-emitting is proposed , This method is able to simultaneously determine component densities , the corresponding temperature and their distributions by a few line intensities measurement. The principle of the method and the relevant measuring system are described. An equation system is established for computation of the state variables in are plasma. An experiment under welding are condition is made as an application of the method. The effects of probable error sources on the measurement are also analysed.

Power Spectral Analysis of Orthogonal Pulse-Based TH-UWB Signals

The paper analyzes power spectral density (PSD) of orthogonal pulse-based signals for time hopping ultra wideband (TH-UWB) systems. Our extensive studies show that the PSD of these signals not only depends on the time dithering code and the modulation schemes, but also on the energy spectral density (ESD) of orthogonal pulses. The different order orthogonal pulses provide different ESD which changes the shape of continuous spectral component with symbols. We show that orthogonal pulse-based signals reduce the dynamic range of amplitude of discrete spectral components. Further, we reduce the dynamic range by adopting longer TH code over orthogonal pulse-based signals. As a result, UWB system performance improves with average transmitted power. The theoretical analysis of PSD of orthogonal pulse-based TH-UWB signal is provided in details and verified through simulation results.