期刊文献+
共找到8篇文章
< 1 >
每页显示 20 50 100
Tribological properties of nanostructured Al_2O_3-40%TiO_2 multiphase ceramic particles reinforced Ni-based alloy composite coatings 被引量:9
1
作者 何龙 谭业发 +2 位作者 谭华 周春华 高立 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2013年第9期2618-2627,共10页
The Ni-based alloy composite coatings reinforced by nanostructured Al2O3-40%TiO2 multiphase ceramic particles were prepared on the surface of 7005 aluminum alloy by plasma spray technology. The microstructure and trib... The Ni-based alloy composite coatings reinforced by nanostructured Al2O3-40%TiO2 multiphase ceramic particles were prepared on the surface of 7005 aluminum alloy by plasma spray technology. The microstructure and tribological properties of the composite coatings were researched. The results show that the composite coatings mainly consist of γ-Ni, α-Al2O3, γ-Al2O3 and rutile-TiO2 etc, and exhibit lower friction coefficients and wear losses than the Ni-based alloy coatings at different loads and speeds. The composite coating bears low contact stress at 3 N and its wear mechanism is micro-cutting wear. As loads increase to 6-12 N, the contact stress is higher than the elastic limit stress of worn surface, and the wear mechanisms change into multi-plastic deformation wear, micro-brittle fracture wear and abrasive wear. With the increase of speeds, the contact temperature of worn surface increases. The composite coating experiences multi-plastic deformation wear, fatigue wear and adhesive wear. 展开更多
关键词 nanostructured A1203-TiO2 multiphase ceramic particles ni-based alloy composite coating plasma spray friction wear
下载PDF
Tribological properties of Ni-base alloy composite coating modified by both graphite and TiC particles 被引量:8
2
作者 蔡滨 谭业发 +2 位作者 屠义强 王小龙 谭华 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2011年第11期2426-2432,共7页
In order to reduce the friction coefficient of Ni-base alloy coating and further improve its wear resistance,Ni-base alloy composite coatings modified by both graphite and TiC particles were prepared by plasma spray t... In order to reduce the friction coefficient of Ni-base alloy coating and further improve its wear resistance,Ni-base alloy composite coatings modified by both graphite and TiC particles were prepared by plasma spray technology on the surface of 45 carbon steel.The results show that friction coefficient of the composite coating is 47.45% lower than that of the Ni-base alloy coating,and the wear mass loss is reduced by 59.1%.Slip lines and severe adhesive plastic deformation are observed on the worn surface of the Ni-base alloy coating,indicating that the wear mechanisms of the Ni-base alloy coating are multi-plastic deformation wear and adhesive wear.A soft transferred layer abundant in graphite and ferric oxide is developed on the worn surface of the composite coating,which reduces the friction coefficient and wear loss in a great deal.The main wear mechanism of the composite coating is fatigue delamination of the transferred layer. 展开更多
关键词 ni-base alloy plasma spraying composite coating GRAPHITE TiC TRIBOLOGY
下载PDF
Tribological behavior and mechanisms of graphite/CaF_2/TiC/Ni-base alloy composite coatings 被引量:4
3
作者 蔡滨 谭业发 +2 位作者 何龙 谭华 王小龙 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2013年第2期392-399,共8页
In order to reduce the friction coefficients and improve the wear resistance of mechanical parts, which work in the severe friction and wear conditions at heavy loads, the graphite/CaFg/TiC/Ni-base alloy composite coa... In order to reduce the friction coefficients and improve the wear resistance of mechanical parts, which work in the severe friction and wear conditions at heavy loads, the graphite/CaFg/TiC/Ni-base alloy composite coatings were prepared by plasma spray and their tribological behavior and mechanisms were investigated. The results show that the friction coefficients of the composite coatings are in the range of 0.22-0.288, which are reduced by 25.9% to 53% compared with those of the pure Ni-base alloy coatings, and the wear rates of the former are 18.6%-70.1% less than those of the latter. When wear against GCr15 steel balls, a transferred layer mainly composed of ferric oxides, graphite and CaF2 may gradually develop on the worn surface of the composite coatings, which made the friction and wear between GCr15 steel ball and the composite coatings change into that between the former and the transferred layer. So the friction coefficients and the wear lubrication effect of the transferred layer. The main wear layer in friction process. rates of the composite coatings are greatly reduced because of the solid mechanism of the composite coatings is delamination of the transferred 展开更多
关键词 plasma spray composite coatings ni-base alloy GRAPHITE TIC CAF2 TRIBOLOGY
下载PDF
Effects of graphite content on microstructure and tribological properties of graphite/TiC/Ni-base alloy composite coatings 被引量:4
4
作者 蔡滨 谭业发 +2 位作者 屠义强 王小龙 徐婷 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2011年第8期1741-1749,共9页
In order to reduce the friction coefficients and further improve the anti-wear properties of Ni-base alloy coatings reinforced by TiC particles,graphite/TiC/Ni-base alloy(GTN) coatings were prepared on the surface o... In order to reduce the friction coefficients and further improve the anti-wear properties of Ni-base alloy coatings reinforced by TiC particles,graphite/TiC/Ni-base alloy(GTN) coatings were prepared on the surface of 45 carbon steel.The effects of graphite content on the microstructure and tribological properties of the GTN coatings were investigated.The results show that the addition of graphite to the GTN coatings may greatly reduce the friction coefficients and improve their wear resistance.The 6.56GTN and 12.71GTN coatings exhibit excellent integrated properties of anti-friction and wear resistance under low and high loads,respectively.Under a low load,the wear mechanisms of the GTN coatings are mainly multi-plastic deformation with slight abrasive wear and gradually change into mixture of multi-plastic deformation,delamination and micro-cutting wear with the increase of graphite fraction.As the load increases,the main wear mechanisms gradually change from micro-cracks,micro-cutting and adhesive wear to micro-cutting and micro-fracture with the increase of graphite fraction. 展开更多
关键词 TIC GRAPHITE ni-base alloy plasma spray composite coating friction and wear
下载PDF
Fabrication of in-situ synthesized ceramic reinforced Ni-based alloy composite coatings by reactive braze coating processing 被引量:3
5
作者 Pei Xinjun Liu Wenbin +3 位作者 Cheng ge Pan Xinyu Li Aina Li haishen 《China Welding》 EI CAS 2019年第4期56-62,共7页
In-situ synthesized ceramic such as TiC,Cr7C3 and Cr5B3 reinforced Ni-based alloy composite coating was fabricated on the surface of mild steel substrate by reactive braze coating processing with colloidal graphite,Cr... In-situ synthesized ceramic such as TiC,Cr7C3 and Cr5B3 reinforced Ni-based alloy composite coating was fabricated on the surface of mild steel substrate by reactive braze coating processing with colloidal graphite,Cr,Ni,ferro-boron,Si and titanium powders as the raw materials at low temperature of 1000℃,and a new kind of coating materials was developed.By means of SEM,EDS,XRD and surface hardness tester,the microstructures,phases,hardness and wear-resistance of the coating were analyzed,respectively.The results revealed that the coating was mainly composed of the ceramic in-situ synthesized reinforcement phases of TiC,Cr7C3 and Cr5B3 and the binder phases in-situ synthesized of Ni31Si12 and(Ni,Fe)solid solution;The ceramic reinforcement phases of TiC,Cr7C3 and Cr5B3 were randomly distributed in the binder phases of Ni31Si12 and(Ni,Fe)solid solution;The coating had about 15vol%pores and can possibly be applied as a self-lubrication coating;The coating and the substrate were integrated together by metallurgical bonding;The coating had a hardness up to 91-94HR15N. 展开更多
关键词 reactive braze coating processing composite coating ni-based alloy CERAMIC self-lubrication coating
下载PDF
Tribological properties and wear prediction model of TiC particles reinforced Ni-base alloy composite coatings 被引量:4
6
作者 谭业发 何龙 +2 位作者 王小龙 洪翔 王伟刚 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2014年第8期2566-2573,共8页
TiC particles reinforced Ni-based alloy composite coatings were prepared on 7005 aluminum alloy by plasma spray. The effects of load, speed and temperature on the tribological behavior and mechanisms of the composite ... TiC particles reinforced Ni-based alloy composite coatings were prepared on 7005 aluminum alloy by plasma spray. The effects of load, speed and temperature on the tribological behavior and mechanisms of the composite coatings under dry friction were researched. The wear prediction model of the composite coatings was established based on the least square support vector machine (LS-SVM). The results show that the composite coatings exhibit smaller friction coefficients and wear losses than the Ni-based alloy coatings under different friction conditions. The predicting time of the LS-SVM model is only 12.93%of that of the BP-ANN model, and the predicting accuracies on friction coefficients and wear losses of the former are increased by 58.74%and 41.87%compared with the latter. The LS-SVM model can effectively predict the tribological behavior of the TiCP/Ni-base alloy composite coatings under dry friction. 展开更多
关键词 TiC particles ni-based alloy composite coating least square support vector machine(LS-SVM) wear prediction model
下载PDF
Microstructure and bonding strength of Ni-based alloy coating
7
作者 LIU Qing SHAO Wen-bao WU Chun-jing 《China Foundry》 SCIE CAS 2006年第2期108-112,共5页
A Ni-Cr-B-Si coating technique was developed and successfully applied on austenite grey iron substrate in a conventional resistance furnace under graphite powder protection. The microstructure, phase distribution, che... A Ni-Cr-B-Si coating technique was developed and successfully applied on austenite grey iron substrate in a conventional resistance furnace under graphite powder protection. The microstructure, phase distribution, chemical composition profile and microhardness along the coating layer depth were investigated. Shear strength of the coating was also tested. Microanalysis shows that the coating is consist of γ-Ni solution and γ-Ni+Ni3B lamellar eutectic, as well as small amount of Cr5B3 particles. Diffusion induced metallurgical bonding occurs at the coating/substrate interfaces, and the higher the temperature, the more sufficient elements diffused, the broader interfusion region and the larger bonding strength, but it has an optimum value. And the bonding strength at the interface can be enable to reach 250-270 MPa, which is nearly the same as that of processed by flame spray. The microhardness along the coating layer depth shows a gradient distribution manner. 展开更多
关键词 composite coating AUSTENITE GREY IRON ni-based self-fluxing alloy POWDER diffusion BONDING strength
下载PDF
氩弧熔覆含Al_2O_3-TiB_2增强颗粒的自熔性镍基合金复合层的冲蚀磨损性能 被引量:1
8
作者 董世知 马壮 +2 位作者 陶莹 李智超 赵越超 《材料保护》 CAS CSCD 北大核心 2015年第6期36-38,44,共4页
为了提高Al2O3-TiB2复相陶瓷涂层的冲蚀磨损性能并降低熔覆成本,以Ni60A自熔性合金粉末、Al2O3粉末以及Al2O3-B2O3体系为原料,在Q235钢表面氩弧熔覆原位合成了Al2O3-TiB2增强颗粒复合层。采用金相显微镜、x射线衍射仪、显微硬度仪及... 为了提高Al2O3-TiB2复相陶瓷涂层的冲蚀磨损性能并降低熔覆成本,以Ni60A自熔性合金粉末、Al2O3粉末以及Al2O3-B2O3体系为原料,在Q235钢表面氩弧熔覆原位合成了Al2O3-TiB2增强颗粒复合层。采用金相显微镜、x射线衍射仪、显微硬度仪及冲蚀磨损试验对熔覆层的显微组织、物相结构、显微硬度和耐冲蚀磨损性能进行分析。结果表明:熔覆层与基体之间的结合方式为冶金结合,界面无气孔、裂纹;熔覆层中有Al2O3,TiB2,Fe2B和Fe19Ni3相生成;熔覆层的显微硬度最高可达771.9HV,较基体提高了3.82倍;熔覆层的冲蚀磨损性能相对基体提高了2.49~4.70倍。 展开更多
关键词 氩弧熔覆 Al2O3-TiB2增强颗粒 镍基合金熔覆层 原位合成 冲蚀磨损
下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部