Stress release mechanism of deep bottom hole rock by ultra-high-pressure water jet slotting

To solve the problems of rock strength increase caused by high in-situ stress,the stress release method with rock slot in the bottom hole by an ultra-high-pressure water jet is proposed.The stress conditions of bottom hole rock,before and after slotting are analyzed and the stress release mechanism of slotting is clarified.The results show that the stress release by slotting is due to the coupling of three factors:the relief of horizontal stress,the stress concentration zone distancing away from the cutting face,and the increase of pore pressure caused by rock mass expansion;The stress concentration increases the effective stress of rock along the radial distance from O.6R to 1R(R is the radius of the well),and the presence of groove completely releases the stress,it also allows the stress concentration zone to be pushed away from the cutting face,while significantly lowering the value of stresses in the area the drilling bit acting,the maximum stress release efficiency can reach 80%.The effect of slotting characteristics on release efficiency is obvious when the groove location is near the borehole wall.With the increase of groove depth,the stress release efficiency is significantly increased,and the release range of effective stress is enlarged along the axial direction.Therefore,the stress release method and results of simulations in this paper have a guiding significance for best-improving rock-breaking efficiency and further understanding the technique.

Joint Slot Scheduling and Power Allocation in Clustered Underwater Acoustic Sensor Networks

Dear Editor, This letter deals with the joint slot scheduling and power allocation in clustered underwater acoustic sensor networks(UASNs),based on the known clustering and routing information, to maximize the network's energy efficiency(EE). Based on the block coordinated decent(BCD) method, the formulated mixed-integer non-convex problem is alternatively optimized by leveraging the KuhnMunkres algorithm.

Effect of an Inclined Slots on the Power Consumption and Vortices Size in a Rushton Turbine Agitated Tank

Mechanical agitation in baffled vessels with turbines plays a vital role in achieving homogeneous fluid mixing and promoting various transfer operations.Therefore,designing vessels with optimal energy efficiency and flow dynamics is essential to enhance operational performance and eliminate flow perturbations.Hence,the present research focuses on a numerical investigation of the impact of inclined slots with different angles installed at the side-wall of a cylindrical vessel equipped with a Rushton turbine.This study explores power consumption and vortex size while considering various rotation directions of the impeller with different rotation speeds.The numerical simulations are conducted for Reynolds numbers ranging from 104 to 105,using the RANS k-εturbulence model to govern the flow inside the stirred vessel,accounting for mass and momentum balances.The results have shown that the installation of slots reduces power consumption and vortex size compared to conventional vessel configu-rations.Moreover,increasing the slot angle from 0 to 32.5°further reduces energy consumption and vortex size,especially with negative rotation speeds.On the other hand,increasing the Reynolds numbers leads to a decrease in power consumption and an increase in vortex size.The present research therefore proposes a design for con-structing Rushton-turbine stirred vessels offering optimal operation,characterized by reduced energy consumption and minimized vortex size.

Adaptive Time Slot Resource Allocation in SWIPT IoT Networks

The rapid advancement of Internet of Things(IoT)technology has brought convenience to people’s lives;however further development of IoT faces serious challenges,such as limited energy and shortage of network spectrum resources.To address the above challenges,this study proposes a simultaneous wireless information and power transfer IoT adaptive time slot resource allocation(SIATS)algorithm.First,an adaptive time slot consisting of periods for sensing,information transmission,and energy harvesting is designed to ensure that the minimum energy harvesting requirement ismet while the maximumuplink and downlink throughputs are obtained.Second,the optimal transmit power and channel assignment of the system are obtained using the Lagrangian dual and gradient descent methods,and the optimal time slot assignment is determined for each IoT device such that the sum of the throughput of all devices is maximized.Simulation results show that the SIATS algorithm performs satisfactorily and provides an increase in the throughput by up to 14.4%compared with that of the fixed time slot allocation(FTS)algorithm.In the case of a large noise variance,the SIATS algorithm has good noise immunity,and the total throughput of the IoT devices obtained using the SIATS algorithm can be improved by up to 34.7%compared with that obtained using the FTS algorithm.

Numerical Study on Mechanism of Blast-Induced Damage Considering Guiding Effect of Water Jet Slot

Damage is one of the most important characteristics of rock failure.Studying the damage mechanism of rock blasting under the guiding effect of the water jet slot and revealing the mechanism of controlled blasting with water jet assistance are crucial.In this study,a rock-like material was chosen as the research object for the calibration experiment of the numerical model.The numerical simulation models were then established by ANSYS/LS-DYNA,and the blastinduced damage mechanism under the guiding effect of the water jet slot was analyzed according to the blasting theory.The results indicated that explosive energy accumulates toward the direction of the slot as the guiding effect of the water jet slot,which allows the rock mass in the direction of the slot bear more damage.Meanwhile,the rock mass in the middle of the connection line between two blast-holes bears more damage under the combination of the effect of the explosion stress wave and guiding effect of water the jet slot on the detonation gas during double-slotted borehole blasting,which results in the formation of a gourd-shaped blast-induced damage area.In addition,the influence of the water jet slot on blast-induced damage varies depending on the blasting-process stage.

Loss Analysis of Magnetic Gear with Slotted in Magnetic Modulation Ring

In order to improve the operation efficiency of coaxial magnetic gear(CMG),in this paper,a CMG model with slotted in magnetic modulation ring is proposed.In this model,the permanent magnets(PMs)of internal and external rotors are distributed in Halbach array,the inner rotor PMs are equally divided into 3 small pieces,and the outer rotor PMs are equally divided into 2 small pieces.At the same time,the static magnetic modulation ring iron blocks are slotted,each iron block has 3 slots,the width of the slot is 0.4°,and the depth of the single side slot is 1mm.Finally,a two-dimensional model is established,and the eddy current loss and iron loss of the model are optimized,compared with the conventional CMG model,it is found that the changed pattern can increase the internal and external output torque by 4%and 4.12%,respectively.The eddy current loss is reduced by 66.57%,and the iron loss is reduced by 8.9%,which significantly improve the operation efficiency of the CMG.

Effect of Pre-Swirling Flow on Performance and Flow Fields in Semi-Opened Axial Fan

In this study, we tried to improve the performance by giving a pre-swirling flow to the radial inflow that occurred in the semi-opened axial fan. In addition, the flow fields of rotor outlet were clarified experimentally, and the effect of pre-swirling flow was considered. The experiment was carried out using a performance test wind tunnel with a square cross section of 880 mm. Three types of casings were prepared, in which the blade tip protruded 0%, 20%, and 40% of the meridional chord length. They were called R25, R15, and R05, respectively, in the casing bellmouth model code. Guide blades for generating a pre-swirling flow were installed on the vertical wall surface of the casing. In addition, a vertical wall was installed 60% upstream of the meridional chord length as an obstacle to prevent axial inflow. The velocity fields of the rotor outlet were measured using a hot-wire anemometer. From the results, the pre-swirling flow did not significantly affect the fan performance. When there was no obstacles wall upstream, there was a partial increase in efficiency, but the difference was not so large. When there was an obstacle wall upstream, the efficiency increased overall in the case of R15, but in the case of R05, the efficiency increased only in the low flow rate region, and conversely decreased in the high flow rate region. By observing the blade outlet flow fields when the performance was improved, it was confirmed that the influence of the tip leakage vortex was weakened.

Compact 5G Vivaldi Tapered Slot Filtering Antenna with Enhanced Bandwidth

Compact fifth-generation(5G)low-frequency band filtering antennas(filtennas)with stable directive radiation patterns,improved bandwidth(BW),and gain are designed,fabricated,and tested in this research.The proposed filtennas are achieved by combining the predesigned compact 5G(5.975–7.125 GHz)third-order uniform and non-uniform transmission line hairpin bandpass filters(UTL and NTL HPBFs)with the compact ultrawide band Vivaldi tapered slot antenna(UWB VTSA)in one module.The objective of this integration is to enhance the performance of 5.975–7.125GHz filtennas which will be suitable for modern mobile communication applications by exploiting the benefits of UWB VTSA.Based on NTL HPBF,more space is provided to add the direct current(DC)biassing circuits in cognitive radio networks(CRNs)for frequency reconfigurable applications.To overcome the mismatch between HPBFs and VTSA,detailed parametric studies are presented.Computer simulation technology(CST)software is used for the simulation in this study.Good measured S11 appeared to be<−13 and<−10.54 dB at 5.48–7.73 and 5.9–7.98GHz with peak realized gains of 6.37 and 6.27 dBi,for VTSA with UTL and NTL HPBFs,respectively which outperforms the predesigned filters.Validation is carried out by comparing the measured and simulated results.

齿调制作用下转子开槽对永磁电机电磁振动影响

为了研究齿调制作用下转子表面开槽对永磁同步电机电磁振动的影响,以小功率分数槽集中绕组(FSCW)内置永磁同步电机(IPMSM)为研究对象,通过麦克斯韦应力张量法推导径向电磁力波的频率及空间阶数特征。分析齿调制作用在FSCW-IPMSM中将空间高阶电磁力波调制为低阶电磁力波的过程,并给出转子表面开槽在齿调制作用影响下与电磁振动间的联系。研究表明,转子表面开槽结构的改变会使各次谐波磁场发生变化,进而改变以极数阶电磁力波为代表的高阶电磁力波的幅值。在齿调制作用下,这些高阶电磁力波会被调制为幅值较高的低阶电磁力波,并引起不同幅度的低阶振动。然后建立C型、V型两种不同转子表面开槽结构的10极12槽FSCW-IPMSM电磁及结构有限元分析模型并进行仿真分析。结果表明,极数阶即10阶电磁力波会被调制为2阶并引起2阶振动,且两种不同开槽结构间的电磁振动存在着高达22.1%的差异。最后,在一台10极12槽样机上进行振动实验,验证理论与仿真分析结果。

基于抽真空系统的继电器线圈BMC热固性塑料模具结构设计

对于原有BMC继电器线圈模具的外观较差、线圈断线丝、生产效率及合格率较低等问题,设计了一种1模16腔布局的上、下双顶出系统的压注模具,通过抽真空系统结构的设计将注塑压力从原充填压力19~42 MPa降低至22~25 MPa,成型件采用电加热及电阻测温方法,上模镶件的温度控制在148~151℃之间,下模镶件的温度控制在148~151℃之间,通过实际生产验证抽真空系统的效果。该改进方案使不合格品率从0.08%降低至0.015%,生产效率提高了20%。结果表明,该模具通过抽真空系统的应用提高了模具的可靠性及稳定性,满足自动化数字化生产线的要求,并且,提高了生产效率与产品的合格率。

基于空闲时隙探测机制的分组帧时隙标签防碰撞算法

多标签碰撞是射频识别系统中无法避免的问题,大量的标签碰撞会增加系统的能量消耗和时间开销,严重影响系统的识别效率。为此提出一种新型的标签防碰撞算法,该算法结合了传统帧时隙算法简单易实施的优点,同时引入了分组和空闲时隙探测机制,以极小的探测时隙开销,消除了识别过程中的空闲时隙,同时减低了标签冲突概率。仿真结果显示,相对于FuzzyQ算法和帧时隙ALOHA算法,本算法平均吞吐率提高了22.64%和61.74%,系统通信传输量平均节省了16.73%和30.41%。

基于自发数据传输的高效双LAN太赫兹无线局域网MAC协议

针对现有的双局域网(LAN)太赫兹无线局域网(Dual-LAN THz WLAN)相关介质访问控制(MAC)协议中存在的某些节点会在多个超帧内重复发送相同的信道时隙请求帧以申请时隙资源以及网络运行的一些时段存在空闲时隙等问题,提出一种基于自发数据传输的高效MAC协议——SDTE-MAC(high-Efficiency MAC protocol based on Spontaneous Data Transmission)。SDTE-MAC通过让各节点都维护一张或多张时间单元链表,使各节点与其余节点在网络运行时间上达到同步,从而获悉各节点应该在信道空闲时隙的什么位置开始发送数据帧,优化了传统的信道时隙分配和信道剩余时隙再分配的流程,提高了网络吞吐量和信道时隙利用率,降低了数据时延,能够进一步提升双LAN太赫兹无线局域网的性能。仿真结果表明,网络饱和时,相较于AHT-MAC(Adaptive High Throughout multi-pan MAC protocol)中的N-CTAP(Normal Channel Time Allocation Period)时段时隙资源分配新机制以及自适应缩短超帧时段机制,SDTE-MAC的MAC层吞吐量提升了9.2%,信道时隙利用率提升了10.9%,数据时延降低了22.2%。

联合多意图识别与语义槽填充的双向交互模型

意图识别与语义槽填充是口语理解的两个主要任务,两者具有高度相关性,通常进行联合训练。随着口语理解任务的深入,研究发现用户在现实场景中的话语往往含有多个意图。但部分联合模型只能识别用户话语中的单个意图,未能充分建模多个意图和语义槽之间的关联性。考虑到话语中多个意图的信息可以引导语义槽填充,语义槽信息也可以帮助意图更好的识别,模型采用图注意力网络建立意图和语义槽之间的双向交互。具体的,将两个任务双向关联以便模型能够挖掘多个意图与语义槽之间的关系,同时引入两个任务的标签信息使模型能够学习到话语上下文和标签的关系,从而提高意图识别与语义槽填充的准确率,优化口语理解的整体性能。实验表明,模型在MixATIS和MixSNIPS两个多意图数据集上对比其他模型性能得到了显著提升。

预制拼接槽型UHPC柱偏心受压性能试验研究

为研究预制拼接槽型UHPC柱在受压条件下的力学性能及其影响因素,开展2根整浇UHPC柱及14根预制拼接槽型UHPC柱在不同拼接形式、不同偏心受压方向及不同偏心距下的轴心或偏心受压试验研究.通过考察试件的极限承载力、破坏形态、轴向及侧向变形性能,研究了拼接方式、偏压方向和偏心距对其静力性能的影响.试验结果表明:钢纤维延缓了UHPC的开裂,增强了试件的变形能力,但预制拼接槽型UHPC柱在轴压和小偏压荷载下仍表现出明显脆性破坏特征;在该试验中,偏压柱的破坏形态主要为小偏心受压破坏及大偏心受拉破坏;在相同偏心距下,不同拼接形式、不同偏心受压方向的柱体破坏形态及承载能力表现趋于一致;在相同尺寸与配筋下,预制拼接槽型UHPC柱承载力随偏心距的增加而减小.最后,通过对比试件承载力试验值和我国现行规范理论计算值,定性地指出了现行规范的局限性.本文试验数据可为预制拼接槽型UHPC柱设计提供参考.

机场航班时刻资源管理研究进展

繁忙机场都会面临严重的交通拥堵和航班延误问题。解决该问题的一个有效手段是对机场航班时刻资源进行优化管理。全面介绍了航班时刻资源管理相关的研究进展,系统回顾了机场公布容量设置、机场航班时刻配置的主要方法和手段。从公布容量确定、单机场、机场网络层面和机场群航班时刻配置及航班时刻配置技术复杂性等方面,得出机场航班时刻资源优化配置的关键技术问题。展望了机场航班时刻资源管理的主要方向,并对下一步研究提出建议。

窄河谷大夹角挑流消能工体型优化研究

针对窄河谷大夹角条件下挑流消能易出现冲击两岸、冲坑过深的问题,采用水工整体模型试验方法对具有代表性的某水利枢纽深孔放水冲沙洞挑流鼻坎体型开展优化研究,并对比分析了水舌形态和下游河道冲刷特性。结果表明,不对称收缩的异型窄缝式消能工可使水流在狭窄河道归槽,水舌纵向拉伸效果较好,大幅减轻了河床冲刷;提出了收缩比、收缩角差、斜切面积比等特征参数适宜的挑流消能工体型,可供窄河谷大夹角条件下挑流消能设计参考。

叶巴滩水电站左岸坝肩槽开挖爆破技术

拱坝坝肩槽的开挖质量对工程运行的安全有重要影响,基于叶巴滩水电站左岸坝肩槽开挖,采用预裂孔+垂直梯段孔爆破技术搭配合理的钻爆参数,严格控制装药量及最大单响药量,并采用分段微差延时爆破技术,取得了良好的开挖效果并积累丰富的工程经验。现场开挖施工结果表明,坝肩槽开挖成型优良,且有效减少对保留岩体的损伤,使坝肩槽爆破开挖质量满足设计要求。

温度影响下的开槽盘式磁力耦合器调速特性

针对温度影响下盘式磁力耦合器调速问题,以一台6对极16槽的开槽盘式磁力耦合器为研究对象,基于矢量磁位法,结合修正三维端部效应的卡特系数并考虑温度对永磁体剩磁的影响,依据磁力耦合器轴向介质不同与导体盘轭铁和铜导体交替排列的结构,推导出其整体的电磁转矩公式。再分别建立恒转矩负载、二次方率负载和恒功率负载工况下的调速关系解析模型。通过有限元模拟分析,确定了不同温度、不同气隙下的开槽盘式磁力耦合器在3种不同负载工况下的调速范围与调速特性。最后,搭建试验平台进行调速性能试验,将不同负载工况下磁力耦合器电磁转矩与输出转速的理论、仿真、实验值三者进行对比,结果表明理论模型有较高的准确性,为开槽型磁力耦合器在调速系统中的智能调控提供了理论依据。

开槽机器人履带支撑架有限元分析及优化

履带支撑架作为开槽机器人履带底盘的重要支撑构件,其性能的好坏直接决定了开槽机器人的使用寿命。为进一步提高履带支撑架的结构可靠性并避免履带支撑架在使用中产生共振现象,文中基于有限元分析软件Ansys Workbench对履带支撑架进行有限元分析,通过静力学分析得出履带支撑架的变形及应力情况并针对履带支撑架的不足之处提出改进方案,改善了履带支撑架的应力分布情况,使其结构更加合理。然后对改进后履带支撑架进行模态分析,得出前10阶的固有频率与最大位移,反映出履带支撑架在不同频率下的动态特性。经过对履带支撑架的有限元分析,可以得出其结构的合理性,并为履带支撑架的机构设计与使用情况提供理论参考。

一种应用于TDMA无线传感网的低能耗同步机制

为了降低时分多址网络中时钟同步所导致的节点能耗,根据节点晶振器件的潜在漂移,提出了一种应用于星型无线传感网的低能耗同步机制。该机制中整个时间轴由长帧组成,每个长帧包含一个同步帧与多个子帧,每个子帧由所有子节点绑定的子时隙构成。根节点在长帧开始时发送同步帧,使得所有子节点时钟同步。每个子时隙增加了相应的保护间隔,有效地避免子节点之间因时钟漂移导致时隙间相互影响,从而最大限度地增加长帧中的子帧数量,降低子节点唤醒进行同步的频率。与传统的TDMA每个子帧均需同步相比,从接收同步帧角度来讲,大幅度减少了子节点能耗。最后,假定晶振频率误差为正态分布的情况下,利用MATLAB进行仿真,验证了该低能耗同步模型公式的正确性,并将仿真情况在CC1310器件构建的星型网上进行了应用验证。