Theory and application research development of semi-solid forming in China

In order to adapt to the trend of ＂energy saving and emission reduction＂ and impel the practical application of semi solid processing （SSP） in China, the progress and application of semi-solid theory in China have been reviewed briefly and systematically. It was emphasized on basic theories, such as formation of globular grains, theology, high pressure solidification and plastic deformation and applications, such as material design, preparation of semi-solid billets （slurries）, thixoforming and application status, which are based on the advantage of semi-solid processing. The results show that the gap of SSP between world level and China exists, especially in application technologies, including market recognition, application fields exploiting, developing of billets （slurries） preparation technologies with low cost and special equipments. The prospect of semi-solid forming development path in China is presented. And we hope that application of SSP has great new breakthrough and development and China wilt be changed from a large metal processing country to a powerful metal processing country.

Semi-solid processing of hypereutectic A390 alloys using novel rheoforming process

The feasibility of semi solid processing of hypereutectic A390 alloys using a novel rheoforming process was investigated. A combination of the swirl enthalpy equilibration device （SEED） process, isothermal holding using insulation and addition of solid alloy during swirling was introduced as a novel method to improve the processability of semi solid slurry. The effects of isothermal holding and the addition of solid alloy on the temperature gradient between the centre and the wall and on the formation of a（Al） particles were examined. In additional tests, phosphorus and strontium were added to the molten metal to refine the primary and eutectic silicon structure to facilitate semi solid processing. The results show that the combination of the SEED process with two additional processing steps can produce semi-solid A390 alloys that can be rheoprocessed. The microstructure reveals an adequate amount of non-dendritic a（Al） globules surrounded by liquid, which greatly improves the processability of semi-solid slurry.

Preparation of AZ91D Slurries for Semi-Solid Forming Using Al8 ( Mn, Fe) 5 Precipitates

During the solidification of the AZ91D-alloys, the Al8(Mn, Fe)5 phase is generally precipitated in the melt in advance of the precipitation of the primary α-Mg. The basic principle for manufacturing AZ91D-alloy slurries for semi solid forming is to use the Al8(Mn, Fe)5 precipitates as the heterogeneous nucleation sites for primary α-Mg phases. Microscopic analysis for the location of the Al8(Mn, Fe)5 precipitate explains that the Al8(Mn, Fe)5 precipitate is the effective heterogeneous nucleation site for the primary α-Mg phase. It was also observed that increase of the Mn content in the melt and the cooling rate below to the solid/liquid two-phase region resulted in smaller and more globular primary α-Mg due to the increase of heterogeneous nucleation sites. It was found that the average α-Mg diameter grew as a function of t0.278, where t is the holding time at the solid/liquid two-phase region. This would be attributed to the Ostwald type ripening and coalescence between primary α-Mg phases. The cooling rate below to the solid/liquid two-phase region, Mn content in AZ91D alloy, and the holding time and temperature affected on the quality of slurry.

Structure of miniature components from steel produced by forming in semi-solid state

To obtain new unconventional structures with specific mechanical and physical properties is possible not only by the development of new types of materials but also by treatment of conventional materials using unconventional innovative technological procedures.One of these technologies is the forming in semi-solid state involving rapid solidification of miniature components from steels.Production of such components is complicated by a number of technical problems.To explain phenomena of the process and structure development,the production of miniature components from the tool steel X210Cr12 difficult to form was experimentally tested.The structure of this originally ledeburite steel consisted of 95 % of metastable austenite after the treatment.Metastable austenite was located particularly in globular and polygonal grains while the remaining interspaces were filled by lamellar network.The detected high stability of extremely high fraction of metastable austenite was tested under different conditions of thermal exposition and mechanical loading.

Spray forming and mechanical properties of a new type powder metallurgy superalloy

The deposited billet of a new type powder metallurgy （PM） superalloy FGH4095M for use in turbine disk manufac- turing has been fabricated using spray forming technology. The metallurgical quality of the deposited billet was analyzed in terms of density, texture, and grain size. Comparative research was done on the microstructure and mechanical properties between the flat disk preform prepared with hot isostatic pressing （HIP） and the same alloy forgings prepared with HIP followed by isothermal forging （IF）. The results show that the density of the spray-formed and nitrogen-atomized deposit billet is above 99% of the theoretical density, indicating a compact structure. The grains are uniform and fine. The billet has weak texture with a random distribution in the spray deposition direction and perpendicular to the direction of deposition. A part of atomizing nitrogen exists in the preform in the form of carbonitride. Nitrogen-induced microporosity causes the density reduction of the preform. Compared with the process of HIP＋IF, the superalloy FGH4095M after HIP has better mechanical properties at both room temperature and high temperature. The sizes of the 7~ phase are finer in microstructure of the preform after HIP in comparison with the forgings after HIP＋IE This work shows that SF＋HIP is a viable processing route for FGH4095M as a turbine-disk material.

Abnormal mechanical property evolution induced by heat treatment for a semi-solid forming hypereutectic Al-Fe base alloy

In the present study, Al-5.5Fe-4Cu-2Zn-0.4Mg-0.5Mn al oy samples were prepared by electromagnetic stirring and semi-solid forming processing, and then the effects of T6 and T1 heat treatments on the microstructures and mechanical properties of the semi-solid forming samples were investigated. The results indicate that after semi-solid forming, the mechanical properties of the sample improved significantly compared to that of the merely electromagnetically stirred sample. The grains of semi-solid forming alloy became almost fine equiaxed; big long strip-shaped Al3 Fe phases became short rod-like morphology and distributed uniformly in the matrix. However, the mechanical properties of the T6-treated semi-solid forming sample decreased significantly instead of increasing and, with solution temperature rising, the tensile strength of the al oy decreased further. The results of EDS show that after high temperature solid-solution treatment, the Cu element in the semi-solid forming alloy sample is mainly concentrated at the boundaries of the Al3 Fe phases instead of being dissolved in the matrix. At the same time, the grains of the semi-solid forming sample grew slightly after solid-solution treatment. Therefore, the growth of the grains and the accumulation of Cu element at Al3 Fe phase boundaries during solution treatment of the semi-solid forming alloy were the main reasons for the mechanical properties decreasing after T6 treatment. The mechanical properties of the alloy were improved after T1 heat treatment due to aging strengthening phase being precipitated in the matrix.

Semi-solid Forming of a Damper Housing with Dendritic and Non-dendritic Al-Si-Mg Alloy

A motorcycle component of damper housing was made by semi-solid forming process. This was used to investigate the effect of microstructures of feedstock on the formability of semisolid process. The soundness and microstructures of casting parts made by dendritic and non-dendritic feedstock were investigated. Separating of liquid phase was found in the casting produced by dendritic feedstock, which might result in defects of porosity, while uniform microstructures were found in the casting produced by no...

Deep drawing of cup shell by powder cavity flexible forming technology

A forming method named powder cavity flexible forming was proposed. It is a forming technology which uses powder medium instead of rigid punch or die to form sheet metals. Cup shells were successfully obtained by this technology. The theoretical calculation equation of forming load was obtained through mechanical analysis and the stress state in cup shells was analyzed by finite element simulation. The results show that powder cavity flexible forming technology can improve the forming limit of sheet metal. Compared with rigid die forming process, the thickness reduction in the punch fillet area significantly decreases and the drawing ratio increases from 1.8 to 2.2. The thinning compressive stress in the bottom of cup shell emerges, which makes the bottom of the cup shell in three-dimensional stress state and the stress in punch fillet region decrease due to powder reaction force, which can effectively inhibit the sever thinning of the sheet and prevent the generation of fracture defects.

Gel-Forming Ability of Rohu as Affected by Egg White Powder Addition

The gel-forming ability of rohu (Labeo rohita) mince with and without egg white powder (EW) was investigated. Gel from washed mince (washed gel) was prepared under two setting conditions: kamaboko (40°C) and modori (60°C). The gel-forming ability of kamaboko and modori gels was improved by the addition of EW at 2%. The autolytic inhibition of kamaboko gel was obtained in gel added with 2% EW, and 1% EW of modori gel. No marked change was observed in the TCA-soluble peptide content of either gel with the addition of EW above 1%. No effect on the whiteness of both gels was shown after the addition of EW. The addition of EW exhibited smaller cavities and a more compact fibrous network in microstructure.

The Design of a Graphical User Environment for Numerical Simulation of Powder Forming Processes

As computer simulation increasingly supports engine er ing design and manufacture, the requirement for a computer software environment providing an integration platform for computational engineering software increas es. A key component of an integrated environment is the use of computational eng ineering to assist and support solutions for complex design. Computer methods fo r structural, flow and thermal analysis are well developed and have been used in design for many years. Many software packages are now available which provi de an advanced capability. However, they are not designed for modelling of powde r forming processes. This paper describes the powder compaction software (PCS_SU T), which is designed for pre- and post-processing for computational simulatio n of the process compaction of powder. In the PCS_SUT software, the adaptive analysis of transient metal powder forming process is simulated by the finite element method based on deformation theories . The error estimates and adaptive remeshing schemes are applied for updated co -ordinate analysis. A generalized Newmark scheme is used for the time domain di scretization and the final nonlinear equations are solved by a Newton-Raphson p rocedure. An incremental elasto-plastic material model is used to simulate the compaction process. To describe the constitutive model of nonlinear behaviour of powder materials, a combination of Mohr-Coulomb and elliptical yield cap model is applied. This model reflects the yielding, frictional and densification char acteristics of powder along with strain and geometrical hardening which occurs d uring the compaction process. A hardening rule is used to define the dependence of the yield surface on the degree of plastic straining. A plasticity theory for friction is employed in the treatment of the powder-tooling interface. The inv olvement of two different materials, which have contact and relative movement in relation to each other, must be considered. A special formulation for friction modelling is coupled with a material formulation. The interface behaviour betwee n the die and the powder is modelled by using an interface element mesh. In the present paper, we have demonstrated pre- and post-processor finite elem ent software, written in Visual Basic, to generate the graphical model and visua lly display the computed results. The software consist of three main part: · Pre-processor: It is used to create the model, generate an app ropriate finite element grid, apply the appropriate boundary conditions, and vie w the total model. The geometric model can be used to associate the mesh with th e physical attributes such as element properties, material properties, or loads and boundary conditions. · Analysis: It can deal with two-dimensional and axi-symmetric applications for linear and non-linear behaviour of material in static and dyna mic analyses. Both triangular and quadrilateral elements are available in the e lement library, including 3-noded, 6-noded and 7-noded (T6B1) triangles and 4 -noded, 8-noded and 9-noded quadrilaterals. The direct implicit algorithm bas ed on the generalized Newmark scheme is used for the time integration and an aut omatic time step control facility is provided. For non-linear iteration, choice s among fully or modified Newton-Raphson method and quasi-Newton method, using the initial stiffness method, Davidon inverse method or BFGS inverse method, ar e possible. · Post-processor: It provides visualization of the computed resu lts, when the finite element model and analysis have been completed. Post-proce ssing is vital to allow the appropriate interpretation of the completed results of the finite element analysis. It provides the visual means to interpret the va st amounts of computed results generated. Finally, the powder behaviour during the compaction of a multi-level component is numerically simulated by the PCS_SUT software, as shown in Fig.1. The predict ive compaction forces at different displacements are computed and compared with the available experimental

Laser rapid forming of low cost hydride-dehydride titanium alloy powder

Low cost hydride-dehydride (HDH) Ti-6Al-4V (Ti-64) alloy powder was employed to investigate the metallurgical quality and mechanical properties of laser formed samples. With appropriate control of the laser forming processing parameters and the loose density of HDH powder, two kinds of defect, i.e. porosity and ill-bonding, can be avoided. Rare earth Nd powder was added to HDH Ti-64 powder to purify laser formed alloy. The results show that with a few additive of Nd, the microstructure of laser formed alloy changes from Widmanstatten morphology to a basket weave microstructure. Accordingly an appropriate addition of Nd is effective to improve both the strength and ductility of laser formed HDH Ti-64 alloy. The values of tensile test meet the wrought specification with the content of Nd ranging from 0.1%-0.2%(mass fraction).

Microstructural evolution of gas atomized Al-Zn-Mg-Cu-Zr powders during semi-solid rolling process

Under H2 atmosphere, the green strips were prepared from Al-5.8Zn-1.63Mg-2.22Cu-0.12Zr(mass fraction, %) powders by the semi-solid rolling process with a relative density from 76.1% to 88.0%. The role of temperature on microstructure and mechanical properties was investigated. With increasing rolling temperature from 580 to 610 °C, the disappearance of primary powder boundary and isolated pores, inter-diffusion of species and the change of grain boundary were accelerated. Moreover, the mechanism of microstructure evolution changes from the densification dominant regime to the coarsening dominant regime; the amount of η(MgZn2) phase decreased and more Al2 Cu particles precipitated at grain boundaries. The optimum temperature for semi-solid rolling of Al-5.8Zn-1.63Mg-2.22Cu-0.12 Zr powders was determined. The liquid fraction in the range of 53% to 67% corresponds with a high density level of green strips. The present experimental analysis suggests that semi-solid powder rolling can be optimized to manufacture strips with high mechanical properties.

Densification process of 10%B_4C-AA2024 matrix composite strips by semi-solid powder rolling

Semi-solid powder rolling（SSPR） is a novel strip manufacturing process,which includes the features of semi-solid rolling and powder rolling.In this work,densification process and deformation mechanisms of B4 C and AA2024 mixed powders in the presence of liquid phase were investigated.The relationships between relative densities and rolling forces were analyzed as well.The results show that liquid fraction plays an important role in the densification process which can be divided into three stages.Rolling deformation is the main densification mechanism in deformation area when the liquid fraction is lower than 20%.When the liquid fraction is equal to or higher than 20%,the flowing and filling of liquid phase are the densification mechanisms in deformation area.The relative densities increase with increasing rolling forces.The relative density–rolling force curves are similar at 550 °C and 585 °C.The characteristics of the curve shapes are apparently different at 605 °C and 625 °C.

Microstructural and mechanical behavior of blended powder semisolid formed Al7075/B_4C composites under different experimental conditions

This work aimed to fabricate B4C reinforced aluminum matrix composites via blended powder semisolid forming that is an implementation of the benefits of semisolid forming to the powder metallurgy. Al7075 elements were incrementally added to ethanol solution under mechanical mixing. Al7075 constituents and B4C particles were blended in a high energy ball mill. Cold compacted Al7075/B4C blends were pressed at semisolid state. The effects of the size of the matrix（20, 45 and 63 μm）, reinforcing volume fraction（5%, 10% and 20%） and semisolid compaction pressure（50 and 100 MPa） on the morphology, microstructure, density, hardness, compression and bending strength were thoroughly analyzed. Experimental results revealed that the highest microstructural uniformity was achieved when large B4C particles（45 μm） were distributed within the small particles（20 μm） of the matrix phase. Composites with matrix particles larger than reinforcing phase indicated agglomerations in loadings more than 10%（volume fraction）. Agglomerated regions resisted against penetration of the liquid phase to the pores and lowered the density and strength of these composites. Composites with 20 μm Al7075 and 20%（volume fraction） 45 μm B4C powder pressed under 100 MPa exhibited the highest values of hardness（HV 190） and compressive strength（336 MPa）.

Isothermal grain growth of reactive spray formed 7075 alloys in semi-solid state

The grain growth behavior in reactive spray formed 7075+2.91 vol percent TiCAl alloy was studied and compared with that of spray formed 7075 Al alloy at semi-solid state. Theeffects of in-situ TiC particles on the microstructure of spray formed 7075 Al alloy were alsoinvestigated. The specimens were heat-treated isothermally at various temperatures between thesolidus and liquidus of 7075 Al alloy for times in the range of 10-60 min, then quenched in water.The microstructure of reheated specimens was characterized using scanning electron microscopy andoptical microscopy. The grain size was measured using a mean linear intercept method. Results showthat the in-situ TiC particles can effectively retard grain growth and refine the grain at a limitedsize. The grain growth exponent in Arrhenius equation increases from 2 to 3, which indicates thatthe in-situ TiC particles have the significant pinning effect on grain coarsening in the semi-solidstate.

Structural evolution of spray-formed Al-70wt.%Si alloys during iso-thermal holding in the semi-solid state

The grain growth behavior of spray-formed Al-70wt.%Si alloys was studied in the semi-solid state. The specimens were isothermally heat-treated at various temperatures between the solidus and liquidus of Al-Si alloys and then quenched in water. The microstructure of reheated specimens was characterized using optical and scanning electron microscopies. The isothermal holding experiment was carried out to investigate grain growth behavior as a function of holding time and temperature in the semi-solid state. The coarsening mechanism and the effect of porosity on microstructure were also studied.

Laser Powder Bed Fusion of Multifunctional Bio-inspired Vertical Honeycomb Sandwich Structures:For the Application of Lightweight Bipolar Plates of Proton Exchange Membrane Fuel Cells

The bipolar plate(BPP)is a crucial component of proton exchange membrane fuel cells(PEMFC).However,the weight of BPPs can account for around 80%of a PEMFC stack,posing a hindrance to the commercialization of PEMFCs.Therefore,the lightweight design of BPPs should be considered as a priority.Honeycomb sandwich structures meet some requirements for bipolar plates,such as high mechanical strength and lightweight.Animals and plants in nature provide many excellent structures with characteristics such as low density and high energy absorption capacity.In this work,inspired by the microstructures of the Cybister elytra,a novel bio-inspired vertical honeycomb sandwich(BVHS)structure was designed and manufactured by laser powder bed fusion(LPBF)for the application of lightweight BPPs.Compared with the conventional vertical honeycomb sandwich(CVHS)structure formed by LPBF under the same process parameters setting,the introduction of fractal thin walls enabled self-supporting and thus improved LPBF formability.In addition,the BVHS structure exhibited superior energy absorption(EA)capability and bending properties.It is worth noting that,compared with the CVHS structure,the specific energy absorption(SEA)and specific bending strength of the BVHS structure increased by 56.99%and 46.91%,respectively.Finite element analysis(FEA)was employed to study stress distributions in structures during bending and analyze the influence mechanism of the fractal feature on the mechanical properties of BVHS structures.The electrical conductivity of structures were also studied in this work,the BVHS structures were slightly lower than the CVHS structure.FEA was also conducted to analyze the current flow direction and current density distribution of BVHS structures under a constant voltage,illustrating the influence mechanism of fractal angles on electrical conductivity properties.Finally,in order to solve the problem of trapped powder inside the enclosed unit cells,a droplet-shaped powder outlet was designed for LPBF-processed components.The number of powder outlets was optimized based on bending properties.Results of this work could provide guidelines for the design of lightweight BPPs with high mechanical strength and high electrical conductivity.

选区激光熔化WC-12Co单道成型工艺参数优化

为了实现硬质合金WC-12Co金属粉末制品整体成型制造,采用选区激光熔化(SLM)技术对WC-12Co合金粉末单道熔池成形进行了理论分析和实验验证,取得了单道熔池成形的最佳工艺参数。结果表明,激光扫描速率和功率的不同组合影响了单道熔池的连续性和形貌,当激光功率为340 W、扫描速率为600 mm/s、扫描间距为60μm/道、铺粉厚度为40μm/层时,单道熔池形貌达到了最佳状态,呈现出稳定连续的“鱼鳞状”形貌,成形对象单层裂纹最少;在单道成形过程中,单道熔池截面出现了W元素聚集的现象,该现象是导致成形WC-Co块体各向异性的重要原因。该研究结果对硬质合金WC-12Co金属粉末制品的成形起到了决定性的作用。

Effect of TiB_2 addition on microstructure of spray-formed Si-30Al composite

An in situ reaction and spray forming technique were employed in the synthesis of 2% TiB2/Si-30Al composite.The formation mechanism of TiB2 particulates was explained based on thermodynamic theory.The modification of the primary Si in the Si-30Al alloy was interpreted in the light of the knowledge of atomic diffusion.The experimental results show that adding 2% TiB2 to the Si-30Al alloy can effectively refine the primary Si.Moreover,the coarsening and growth of primary Si phase in its semi-solid state was retarded effectively due to the existence of the TiB2 particulates.

Effect of Si,Cu and Fe on mechanical properties of cast semi-solid 206 alloys

The development of a modified 206 alloy whose composition was optimized to minimize hot tearing during semi-solid forming was reported. The effect of varying silicon, copper and iron contents was investigated using a design of experiment (DOE) approach. Semi-solid slurries were prepared using the SEED process and injected into a high pressure die casting press. The hot tearing sensitivity results were reported for different alloy variants. The microstructure evolution during the semi-solid preparation was presented along with actual die cast components. The effects of silicon, copper and iron on mechanical properties in the T7 condition were also analyzed. Beyond the benefit of reducing hot tearing, it is shown that the tensile and fatigue properties remain compatible with the automotive industry requirements.