Strain hardening behavior, strain rate sensitivity and hot deformation maps of AISI 321 austenitic stainless steel

Hot compression tests were performed on AISI 321 austenitic stainless steel in the deformation temperature range of 800–1200℃ and constant strain rates of 0.001,0.01,0.1,and 1 s^(−1).Hot flow curves were used to determine the strain hardening exponent and the strain rate sensitivity exponent,and to construct the processing maps.Variations of the strain hardening exponent with strain were used to predict the microstructural evolutions during the hot deformation.Four variations were distinguished reflecting the different microstructural changes.Based on the analysis of the strain hardening exponent versus strain curves,the microstructural evolutions were dynamic recovery,single and multiple peak dynamic recrystallization,and interactions between dynamic recrystallization and precipitation.The strain rate sensitivity variations at an applied strain of 0.8 and strain rate of 0.1 s^(−1) were compared with the microstructural evolutions.The results demonstrate the existence of a reliable correlation between the strain rate sensitivity values and evolved microstructures.Additionally,the power dissipation map at the applied strain of 0.8 was compared with the resultant microstructures at predetermined deformation conditions.The microstructural evolutions strongly correlated to the power dissipation ratio,and dynamic recrystallization occurred completely at lower power dissipation ratios.

STRAIN RATE SENSITIVITY OF ULTRAFINE-GRAINED Cu WITH NANOSIZED TWINS

An ultrafine-grained Cu sample with a high density of growth twins was synthesized by means of pulsed electrodeposition technique. The strain rate sensitivity of the Cu sample was measured by strain rate cycling tests under tension. The effects of grain size as well as twin density on the strength and strain rate sensitivity were discussed.

Estimation of enhanced low dose rate sensitivity mechanisms using temperature switching irradiation on gate-controlled lateral PNP transistor

The mechanisms occurring when the switched temperature technique is applied, as an accelerated enhanced low dose rate sensitivity （ELDRS） test technique, are investigated in terms of a specially designed gate-controlled lateral PNP transistor （GLPNP） that used to extract the interface traps （Nit） and oxide trapped charges （Not）. Electrical characteristics in GLPNP transistors induced by 60Co gamma irradiation are measured in situ as a function of total dose, showing that generation of Nit in the oxide is the primary cause of base current variations for the GLPNP. Based on the analysis of the variations of Nit and Not, with switching the temperature, the properties of accelerated protons release and suppressed protons loss play critical roles in determining the increased Nit formation leading to the base current degradation with dose accumulation. Simultaneously the hydrogen cracking mechanisms responsible for additional protons release are related to the neutralization of Not extending enhanced Nit buildup. In this study the switched temperature irradiation has been employed to conservatively estimate the ELDRS of GLPNP, which provides us with a new insight into the test technique for ELDRS.

Strain rate sensitivity and activation volume of electrodeposited nanocrystalline Ni and Ni-Co alloys

Tensile deformation behaviors of the electrodeposited 40 nm grain sized Ni,25 nm Ni-1.7 wt.%Co,and 13 nm Ni-8.6 wt.%Co alloys at various strain rates and room temperature were reviewed with emphasis on strain rate sensitivity and activation volume,respectively.It is found that the strain rate sensitivity and activation volume were strongly grain size dependent.An analytic model based on the bow out of a single dislocation well predicted the relationship between the strain rate sensitivity and the activation volumes for these nanocrystaline metals.

The strain rate sensitive and anisotropic behavior of rare-earth magnesium alloy ZEK100 sheet

To overcome the limitation in formability at room temperature,manufacturers have developed magnesium alloys with remarkable properties by adding rare-earth elements.The rare-earth magnesium alloys behave differently from the conventional alloys,especially with respect to their coupled anisotropic and strain rate sensitive behavior.In the current work,such behavior of the rare-earth Mg alloy ZEK100 sheet at room temperature is investigated with the aid of the elastic viscoplastic self-consistent polycrystal plasticity model.Different strain rate sensitivities(SRSs)for various deformation modes are employed by the model to simulate the strain rate sensitive behaviors under different loading directions and loading rates.Good agreement between the experiments and simulations reveals the importance and necessity of using different SRSs for each deformation mode in hexagonal close-packed metals.Furthermore,the relative activities of each deformation mode and the texture evolution during different loadings are discussed.The anisotropic and strain rate sensitive behavior is ascribed to the various operating deformation modes with different SRSs during loading along different directions.

Effect of strain rate on the compressive deformation behaviors of lotus-type porous copper

Lotus-type porous copper was fabricated by unidirectional solidification, and compressive experiments were subsequently conducted in the strain rate range of 10-3-2400 s-1 with the compressive direction parallel to the pores. A GLEEBLE-1500 thermal-mechanical simulation system and a split Hopkinson pressure bar （SHPB） were used to investigate the effect of strain rate on the compressive deforma-tion behaviors of lotus-type porous copper. The influence mechanism of strain rate was also analyzed by the strain-controlling method and by high-speed photography. The results indicated that the stress-strain curves of lotus-typed porous copper consist of a linear elastic stage, a plateau stage, and a densification stage at various strain rates. At low strain rate （〈1.0 s^-1）, the strain rate had little influence on the stress-strain curves; but when the strain rate exceeded 1.0 s^-1, it was observed to strongly affect the plateau stage, showing obvious strain-rate-hardening characteristics. Strain rate also influenced the densification initial strain. The densification initial strain at high strain rate was less than that at low strain rate. No visible inhomogeneous deformation caused by shockwaves was observed in lotus-type porous copper during high-strain-rate deformation. However, at high strain rate, the bending deformation characteristics of the pore walls obviously differed from those at low strain rate, which was the main mechanism by which the plateau stress exhibited strain-rate sensitivity when the strain rate exceeded a certain value and exhibited less densification initial strain at high strain rate.

Effect of ionizing radiation on dual 8-bit analog-to-digital converters (AD9058) with various dose rates and bias conditions

The radiation effects on several properties （reference voltage, digital output logic voltage, and supply current） of dual 8-bit analog-to-digital （A/D） converters （AD9058） under various biased conditions are investigated in this paper. Gamma ray and 10-MeV proton irradiation are selected for a detailed evaluation and comparison. Based on the measurement results induced by the gamma ray with various dose rates, the devices exhibit enhanced low dose rate sensitivity （ELDRS） under zero and working bias conditions. Meanwhile, it is obvious that the ELDRS is more severe under the working bias condition than under the zero bias condition. The degradation of AD9058 does not display obvious ELDRS during 10-MeV proton irradiation with the selected flux.

Annealing and strain rate effects on the mechanical behavior of ultrafine-grained iron produced by SPD

Thermal stability and strain rate sensitivity of ultrafine-grained(UFG)Fe produced by severe plastic deformation(SPD)were investigated.The UFG Fe was processed by equal-channel angular pressing(ECAP)via route Bc.After 6 passes,the grain size of UFG Fe reaches 600 nm, as confirmed by means of electron back scatter diffraction(EBSD).Examination of micro-hardness and grain size of UFG Fe as a function of post-ECAP annealing temperature shows a transition from recovery to recrystallization.The critical transition temperature is approximately 500℃,and the material has a bimodal structure after annealing at this temperature.Deformation behaviors of ECAP Fe and ECAP + annealing Fe were studied under both quasi-static and dynamic compressive loadings.The UFG iron shows increased strength and reduced strain rate sensitivity compared with its coarse-grained counterparts.The appropriate post-ECAP annealing can increase strain hardening ability and cancel out thermal softening effect with only a small loss of strength under dynamic loading.

Creep rate sensitivities of materials by a depth-sensing indentation technique

The strain rate sensitivity to creep of single crystal Cu（110）, metal tantalum, and 128°Y-X LiNbO3 piezoelectric single crystal were measured at room temperature by MTS Nanoindenter XP. Among the three kinds of materials studied, Cu showed the highest degree of resistance to creep-induced deformation, which is followed by Ta, while the LiNbO3 single crystal deformed more readily than the others. The values of the steady-state strain rate sensitivities determined by the indentation methods are in the range of 0.002-0.006, 0.02-0.06 and 0.02-0.03 for Cu, Ta, and LiNbO3, respectively. The mechanisms for the indentation-induced creeping behavior and the factors that influenced the creeping are discussed.

STRAIN RATE SENSITIVTTY OF POLYCRYSTALLINE AND SINGLE CRYSTAL NiAl

The compressive and tensile strain rate sensitivities of polycrystalline and single crystal NiAl have been evaluated at 877 ℃ which is well above DBTT. Samples were prepared to specific sizes by hot press consolidation of appropriate powder sizes and minimizing past consolidation thermal exposures. NiAl single crystals were grown in the [100]orientation using a modified Bridgeman technique. The yield and tensile strength of polycrystalline NiAl as a function of grain size generally follows a Hall-Petch type relationship . A tensile strain rate effect was found at strain rate of 1 to 10-4 sec-1. The strain rate sensitivity coefficient, m,in the equation of σ = Kε is in the range of 0. 10 to 0. 13. The highest strain rate (1 sec-1) resulted in significantly higher strengths and little or no observed ductility. Compressive strain rate testing al strain rate of 10-5to 10-2 sec-1 and at temperature of 1050°to 1250°K was conducted both for polycrystalline and for single crystal NiAl. The calculated stress exponents and the activation energy for creep were compared with the reference data.

Advanced test methods of material property characterization:high strain-rate testing and experimental simulation of multiaxial stress states

Optimum utilization of the loading capability of engineering materials is an important and active contribution to protect nature's limited resources,and it is the key for economic design methods.In order to make use of the materials' resources,those must be known very well;but conventional test methods will offer only limited informational value.The range of questions raised is as wide as the application of engineering materials,and partially they are very specific.The development of huge computer powers enables numeric modelling to simulate structural behaviour in rather complex loading environments-so the real material behaviour is known under the given loading conditions.Here the art of material testing design starts.To study the material behaviour under very distinct and specific loading conditions makes it necessary to simulate different temperature ranges,loading speeds, environments etc.and mostly there doesn't exist any commonly agreed test standard.In this contribution two popular,non-standard test procedures and test systems will be discussed on the base of their application background,special design features as well as test results and typically gained information:The demand for highspeed tests up to 1000 s^(-1) of strain rate is very specific and originates primarily in the automotive industry and the answers enable CAE analysis of crashworthiness of vehicle structures under crash conditions.The information on the material behaviour under multiaxial loading conditions is a more general one.Multiaxial stress states can be reduced to an equivalent stress,which allows the evaluation of the material's constraint and criticality of stress state.Both discussed examples shall show that the open dialogue between the user and the producer of testing machines allows custom-tailored test solutions.

Effects of Strain Rate and Texture on the Tensile Behavior of Pre-strained NiCr Microwires

The stress–strain behavior and strain rate sensitivity of pre-strained Ni80Cr20（Ni20Cr） were studied at strain rates from 4.8×10^（–4）s^（–1） to 1.1×10^（–1）s^（–1）. Specimens were prepared through cold drawing with abnormal plastic deformation. The texture of the specimen was characterized using electron backscatter diffraction. Results revealed that the ultimate tensile strength and ductility of the pre-strained Ni20Cr microwires simultaneously increased with increasing strain rate. Twinning-induced negative strain rate sensitivity was discovered. Positive strain rate sensitivity was present in fracture flow stress, whereas negative strain rate sensitivity was detected in flow stress values of σ_（0.5%） and σ_（1%）. Tensile test of the pre-strained Ni20Cr showed that twinning deformation predominated, whereas dislocation slip deformation dominated when twinning deformation reached saturation. The trends observed in the fractions of 2°-5°, 5°-15°, and 15°-180° grain boundaries confirmed that twinning deformation dominated the first stage.

A Novel Machine Learning-Based Hand Gesture Recognition Using HCI on IoT Assisted Cloud Platform

Machine learning is a technique for analyzing data that aids the construction of mathematical models.Because of the growth of the Internet of Things(IoT)and wearable sensor devices,gesture interfaces are becoming a more natural and expedient human-machine interaction method.This type of artificial intelligence that requires minimal or no direct human intervention in decision-making is predicated on the ability of intelligent systems to self-train and detect patterns.The rise of touch-free applications and the number of deaf people have increased the significance of hand gesture recognition.Potential applications of hand gesture recognition research span from online gaming to surgical robotics.The location of the hands,the alignment of the fingers,and the hand-to-body posture are the fundamental components of hierarchical emotions in gestures.Linguistic gestures may be difficult to distinguish from nonsensical motions in the field of gesture recognition.Linguistic gestures may be difficult to distinguish from nonsensical motions in the field of gesture recognition.In this scenario,it may be difficult to overcome segmentation uncertainty caused by accidental hand motions or trembling.When a user performs the same dynamic gesture,the hand shapes and speeds of each user,as well as those often generated by the same user,vary.A machine-learning-based Gesture Recognition Framework(ML-GRF)for recognizing the beginning and end of a gesture sequence in a continuous stream of data is suggested to solve the problem of distinguishing between meaningful dynamic gestures and scattered generation.We have recommended using a similarity matching-based gesture classification approach to reduce the overall computing cost associated with identifying actions,and we have shown how an efficient feature extraction method can be used to reduce the thousands of single gesture information to four binary digit gesture codes.The findings from the simulation support the accuracy,precision,gesture recognition,sensitivity,and efficiency rates.The Machine Learning-based Gesture Recognition Framework(ML-GRF)had an accuracy rate of 98.97%,a precision rate of 97.65%,a gesture recognition rate of 98.04%,a sensitivity rate of 96.99%,and an efficiency rate of 95.12%.

Superplastic behavior of a fine-grained Mg-Gd-Y-Ag alloy processed by equal channel angular pressing

An extruded Mg-6Gd-3Y-1.5Ag(wt%) alloy was processed by 6 passes of equal channel angular pressing(ECAP) at 553 K using route Bc to refine the microstructure. Electron back-scattered diffraction(EBSD) analysis showed a fully recrystallized microstructure for the extruded alloy with a mean grain size of 8.6 μm. The microstructure of the ECAP-processed alloy was uniformly refined through dynamic recrystallization(DRX). This microstructure contained fine grains with an average size of 1.3 μm, a high fraction of high angle grain boundaries(HAGBs), and nano-sized Mg_(5)Gd-type particles at the boundaries of the DRXed grains, detected by transmission electron microscopy(TEM). High-temperature shear punch testing(SPT) was used to evaluate the superplastic behavior of both the extruded and ECAP-processed alloys by measuring the strain rate sensitivity(SRS) index(m-value). While the highest m-value for the extruded alloy was measured to be 0.24 at 673 K, the ECAP-processed alloy exhibited much higher m-values of 0.41 and 0.52 at 598 and 623 K, respectively,delineating the occurrence of superplastic flow. Based on the calculated average activation energy of 118 kJ mol^(-1) and m-values close to 0.5, the deformation mechanism for superplastic flow at the temperatures of 598 and 623 K for the ECAP-processed alloys was recognized to be grain boundary sliding(GBS) assisted by grain boundary diffusion.

On the behaviour characterization of metallic cellular materials under impact loading

This paper reviews the common mechanical features of the metallic cellular material under impact loading as well as the characterization methods of such behaviours. The main focus is on the innovations of various testing methods at impact loading rates.Following aspects were discussed in details.（1） The use of soft nylon Hopkinson/Kolsky bar for an enhanced measuring accuracy in order to assess if there is a strength enhancement or not for this class of cellular materials under moderate impact loading;（2） The use of digital image correlations to determine the strain fields during the tests to confirm the existence of a pseudo-shock wave propagation inside the cellular material under high speed impact： （3） The use of new combined shear compression device to determine the loading envelop of cellular materials under impact multiaxial loadings.

Strain-hardening and warm deformation behaviors of extruded Mg-Sn-Yb alloy sheet

Strain-hardening and warm deformation behaviors of extruded Mg-2Sn-0.5Yb alloy(at.%)sheet were investigated in uniaxial tensile test at temperatures of 25-250 ℃ and strain rates of 1×10^(−3) s^(−1)-0.1 s^(−1).The data fit with the Kocks-Mecking type plots were used to show different stages of strain hardening.Besides III-stage and IV-stage,the absence of the II-stage strain hardening at room temperature should be related to the sufficient dynamic recrystallization during extrusion.The decrease of strain hardening ability of the alloy after yielding was attributed to the reduction of dislocation density with increasing testing temperature.Strain rate sensitivity(SRS)was significantly enhanced with increasing temperature,and the corresponding m-value was calculated as 0.07-0.12,which indicated that the deformation mechanism was dominated by the climb-controlled dislocation creep at 200 ℃.Furthermore,the grain boundary sliding(GBS)was activated at 250 ℃,which contributed to the higher SRS.The activation energy was calculated as 213.67 kJ mol^(−1),which was higher than that of lattice diffusion or grain boundary self-diffusion.In addition,the alloy exhibited a quasi superplasticity at 250 ℃ with a strain rate of 1×10^(−3) s^(−1),which was mainly related to the fine microstructure and the presence of the Mg2Sn and Mg2(Sn,Yb)particles.

Cooling Rate Sensitivity of RE-Containing Grain Refiner and Its Impact on the Microstructure and Mechanical Properties of A356 Alloy

The cooling rate sensitivities of A1TiB, RE and A1TiB-RE refiners were investigated using laboratory experiments and the actual industrial applications of A356 automotive wheel via low pressure die casting technology. Their impact mechanisms on the microstructure and mechanical properties of the A356 alloy were discussed. The results demonstrated that the AITiB-RE refiner possessed most effective and synergetic refinement effects compared to the individual A1TiB or RE refiners. The A1TiB-RE refiner exhibited the least sensitivity to the cooling rate changes than the other refiners. The comprehensive properties of alloy wheel refined by the A1TiB-RE refiner were improved significantly. The tensile strength, yield strength, and elongation of wheel spoke improved by approximately 11.3%, 10.8% and 44.1%, respectively. The property difference values of the tensile strength, yield strength, and elongation in different positions of the wheel decreased from 14.8%, 31.2% and 47.7% to 8.6%, 27.1% and 30.9%, respectively.

DETERMINATION OF THE PARAMETERS OF SUPERPLASTIC FORMING FOR LONG RECTANGULAR THIN SHEET TITANIUM ALLOY Ti-6A1-4V

A method for determining the value of the strain rate sensitivity parameter m, of a thin sheet superplastic material, which is based on the results of constant gas pressure tests, has been developed in this paper. Unlike the conventional procedures the method involved provides the test conditions similar to those occurring during an industrial technological process. Such an approach enables one to estimate reliable the superplas- tic properties of the material under study. Theoretical analysis is based upon use of the standard equations of the membrane theory. The experimental investigations have been carried out for Ti-based alloy VT6 (Ti--6Al-4V). Theoretical predictions show satisfactory agreement with experimental data. The results obtained are compared with those measured by means of standard procedures (constant cross-head velocity experiments and load relaxation tests). It is shown that the use of specimens having reduced gage length (which is less than specimen's width) could lead to considerable errors in experimental estimation of the m value which, in its turn, leads to inaccurate calculating the technological parameters.

ANALYTICAL EVALUATION OF PERMANENT DEFLECTION OF A THIN CIRCULAR PLATE STRUCK NORMALLY AT ITS CENTER BY A PROJECTILE

The permanent deflection of a thin circular plate struck normally at its center by a projectile is studied by an approximate theoretical analysis, FEM simulation and experiment. The plate made of rate sensitive and strain-hardening material undergoes serious local deformation but is not perforated during the impact. The theoretical analysis is based on an energy approach, in which the Cowper-Symonds equation is used for the consideration of strain rate sensitive effects and the parameters involved are determined with the aid of experimental data. The maximum permanent deflections predicted by the theoretical model are compared with those of FEM simulation and published papers obtained both by theory and experiment, and good agreement is achieved for a wide range of thickness of the plates and initial impact velocities.

Inverse grain-size-dependent strain rate sensitivity of face-centered cubic high-entropy alloy

It is well documented that the strain rate sensitivity(m)increases at refined grain size for face-centered cubic(FCC)metals and alloys.Through a series of nanoindentation testing,however,we experimentally demonstrated a striking departure from conventional FCC metals that Co Cr Fe Mn Ni high entropy alloy(HEA)with FCC lattice structure exhibits monotonously decreased m as grain size reduced fromμ30.3m to 7.2 nm.Moreover,the apparent activation volume v*,which generally shows an opposite trend of m,exhibited the identical decreasing trend with reduced grain size as that of m.Such an unusual trend of m and its correlation with v*in the FCC HEA alloys can be understood by a distinct deformationmechanism-transitions and unique dislocation morphology evolution that differs from conventional FCC metals.