Loose-stratification model in separation process for vanadium pre-concentration from stone coal

A technology of one-stage roughing and one-stage scavenging vanadium pre-concentration with shaking table was investigated for improving vanadium grade and decreasing acid consumption minerals content based on the quantitative evaluation of minerals by scanning electronic microscopy （QEMSCAN）. In order to visually illustrate how the vanadium-bearing minerals were separated from system, a loose-stratification model was established with Bagnold shear loose theory and Kelly stratification hypothesis. Through the model, it was inferred that fine fraction and coarse fraction of vanadium-bearing muscovite particles easily became the concentrate in roughing and scavenging stages, respectively. The type of the dominant effect on the loose-stratification was confirmed. In the roughing stage, gravity sedimentation played a leading role in the loose-stratification process. However, in the scavenging stage, shearing dispersion pressure caused by asymmetric motion of table deck took an important part in the loose-stratification process. Finally, the correction of the loose-stratification model was validated by the practical experiment.

Comparative study on efficacy of three sperm-separation techniques

Aim: To evaluate the comparative effectiveness of real-time sperm separation technique (Wang's tube method) andother two conventional methods in isolating high-quality sperm preparation, and to compare the spouse pregnancy ratein intrauterine insemination (IUI) with sperm preparations isolated by these methods. Methods: The effectivenessof the real-time sperm separation technique, the conventional swim-up and the Percoll discontinuous density gradientmethods in isolating sperm preparations from 60 infertile patients (20 with apparently normal semen and 40, abnormalsemen contaminated with microorganisms and other impurities) was evaluated and compared. The microorganisms to beremoved included bacteria, vires, Chlamydia trachomaticum, Ureaplsama urealyticum, etc. The spouse pregnancyrates in IUI with sperm preparations isolated by these three techniques from 80 oligoasthenoteratospermic patients werealso compared. Results: The quality (including the percentages of normal form, normal-chromatin and motilesperm, and the grade of motility) of sperm obtained by the real-time sperm separation technique was much higher ( P< 0.01) as compared with those by the other two methods. The Wang's tube method was also more effective in remov-ing microorganisms and other impurities. The method provided a higher IUI pregnancy rate than the other two spermseparation techniques ( P < 0.05). Conclusion: The real-time sperm separation technique is the most effectivemethod so far available in isolating high-quality sperm samples to be used in assisted reproduction.

Remove volatile organic compounds(VOCs) with membrane separation techniques

Membrane separation, a new technology for removing VOCs including pervaporation, vapor permeation, membrane contactor, and membrane bioreactor was presented. Comparing with traditional techniques, these special techniques are an efficient and energy saving technology. Vapor permeation can be applied to recovery of organic solvents from exhaust streams. Membrane contactor could be used for removing or recovering VOCs from air or wastewater. Pervaporation and vapor permeation are viable methods for removing VOCs from wastewater to yield a VOC concentrate which could either be destroyed by conventional means, or be recycled for reuse.

Progress on the Use of Stable Isotope Techniques in Catchment Hydrograph Separation: A Review

Hydrograph separation is a fundamental catchment descriptor,revealing information about sources of water in runoff generation processes. The water isotopes are ideal tracers in studying hydrological processes since the isotope fractionation produces a natural labeling effect within the hydrologic cycle. The water isotope technique has become one of effective means for investigating complex hydrologic system on a catchment scale. This paper reviews the progress on the use of stable water isotope techniques in catchment hydrograph separation in last decades. Also,the isotope mixing model for hydrograph separation and its uncertainties are explained in detail. In future research,there are three hot issues in the use of isotopic hydrograph separation（ IHS） ： integrating new approaches into IHS,calibration and verification of IHS model and IHS application in large river basins.

Innovative pre-concentration technology for recovering ultrafine ilmenite using superconducting high gradient magnetic separator

To achieve the utilization of the abandoned ultrafine ilmenite(-20 μm) produced in the titanium magnetite processing plant in Panzhihua,the superconducting high-gradient magnetic separation(SMS) technology was proposed in this study.After optimizing the conditions of magnetic intensity,feeding and pulsation,an SMS concentrate with TiO_(2) grade of 16.03% and TiO_(2) recovery of 66.39% was obtained through one roughing-one cleaning pre-concentration flowsheet.The specific magnetic force and magnetic force were calculated and analysed to illustrate the pre-concentration mechanism,and the results revealed that the combination of high magnetic field and strong pulsating resulted in the effective preconcentration of the ultrafine ilmenite in the SMS process.In addition,the magnetic force analysis indicated that the high magnetic intensity and high magnetic gradient are the key factors of the SMS technology.Furthermore,the EDS-Mapping detection certified that the ultrafine ilmenite was concentrated from the gangue minerals using SMS technology.

Visco chop-a new technique for nucleus separation for soft cataracts in femtolaser assisted cataract surgery

【正】INTRODUCTION Femtosecond laser technology,introduced clinically for ophthalmic surgery as a technique for creating lamellar flaps in laser in situ keratomileusis(LASIK),has recently been developed into a tool for cataract surgery.Preliminary experience for femtosecond laser-assisted cataract surgery show appropriate safety and efficacy,and possible advantage over conventional cataract surgery[1-4].The ability of the femtosecond laser to fragment the lens results in the need for less ultrasound energy to be expended inside the eye.Several studies indicate that less effective phacoemulsification time is needed to emulsify the lens

A Sound Field Separation and Reconstruction Technique Based on Reciprocity Theorem and Fourier Transform

We show a method to separate the sound field radiated by a signal source from the sound field radiated by noise sources and to reconstruct the sound field radiated by the signal source. The proposed method is based on reciprocity theorem and the Fourier transform. Both the sound field and its gradient on a measurement surface are needed in the method. Evanescent waves are considered in the method, which ensures a high resolution reconstruction in the near field region of the signal source when evanescent waves can be measured. A simulation is given to verify the method and the influence of measurement noise on the method is discussed.

SEPARATION OF OVERLAPPING INCISIONS OF A.C.OSCILLOPOLAROGRAM USING KALMAN'S FILTER TECHNIQUE

Kalman's Filter Technique for the separation of overlapping incisions of an a.c.oscillopolarogram is presented,the experimental verifications were carried out in various systems with the ions of Pb^(2+),Tl^+,In^(3+)and Cd^(2+).The results showed that the concentration of the depolarizer can be determined directly and easily with this technique in the presence of interference elements.

Liquid phase separating mechanism and preparation techniques of immiscible alloys

Immiscible alloys have attracted growing interest for their valuable physical and mechanical properties. However, their production is difficult because of metallurgical problems in which there is a serious tendency for gravity separation in the region of the miscibility gap. So far the study on the liquid separation mechanism is still one of the important projects in the spatial materials science and the spatial fluid science. The studied results about the liquid phase separating mechanism of immiscible alloys are presented, at the same time the preparation techniques of homogeneous immiscible alloys are summarized, and the existing problems and the related researching areas in the future are also pointed out.

Sprayed separation membranes: A systematic review and prospective opportunities

Membrane separation technology has been taken up for use in diverse applications such as water treatment,pharmaceutical,petroleum,and energy-related industries.Compared with the design of membrane materials,the innovation of membrane preparation technique is more urgent for the development of membrane separation technology,because it not only affects physicochemical properties and separation performance of the fabricated membranes,but also determines their potential in industrialized application.Among the various membrane preparation methods,spray technique has recently gained increasing attention because of its low cost,rapidity,scalability,minimum of environmental burden,and viability for nearly unlimited range of materials.In this Review article,we summarized and discussed the recent developments in separation membranes using the spray technique,including the fundamentals,important features and applications.The present challenges and future considerations have been touched to provide inspired insights for developing the sprayed separation membranes.

Optimization of CO_2 separation technologies for Chinese refineries based on a fuzzy comprehensive evaluation model

This study aims at determining the optimal CO2 separation technology for Chinese refineries, based on current available technologies, by the method of comprehensive evaluation. Firstly, according to the characteristics of flue gas from Chinese refineries, three feasible CO2 separation technologies are selected. These are pressure swing adsorption （PSA）, chemical absorption （CA）, and membrane absorption （MA）. Secondly, an economic assessment of these three techniques is carried out in accordance with cash flow analysis. The results show that these three techniques all have economic feasibility and the PSA technique is the best. Finally, to further optimize the three techniques, a two-level fuzzy comprehensive evaluation model is established, including economic, technological, and environmental factors. Considering all the factors, PSA is optimal for Chinese refineries, followed by CA and MA. Therefore, to reduce Chinese refineries carbon emission, it is suggested that CO2 should be captured from off-gases using PSA.

Separation of Clay Minerals from Host Sediments Using Cation Exchange Resins

Classic physical and chemical treatments applied to separating clay minerals from the host sediments are often difficult or aggressive for clay minerals. A technique using cation exchange resins (amberlite IRC\|50H and amberlite IR\|120) is used to separate clay minerals from the host sediments. The technique is based on the exchange of cations in the minerals that may be associated clay minerals in sediments, such as Ca and Mg from dolomite; Ca from calcite, gypsum and francolite with cations carried by resin radicals. The associated minerals such as gypsum, calcite, dolomite and francolite are removed in descending order. Separation of clay minerals using cation exchange resins is less aggressive than that by other classic treatments. The efficiency of amberlite IRC\|50H in the removal of associated minerals is greater than that of amberlite IR\|120.

The application of combined gravity and seismic data formation separation for revealing deep structure

In some oilfields with 3D seismic data, the deeper structure cannot be observed due to poor quality deep seismic data. Layer stripping using both seismic and gravity data is a solution for this problem but it cannot get satisfactory results because the horizontal variations in formation density are ignored. We present a variable-density formation separation technique to address this problem. Based on 3D seismic depth data and laterallyvariable density derived from 3D seismic velocity data, the upper formation gravity effect is calculated by forward modeling and removed from the Bouguer gravity. The formation-separated gravity anomaly with variable density is obtained, which mainly reflects the deeper geological structure. In block XX of North Africa, the shallow formations seismic data is excellent but the data at the top of basement is poor. The formation-separated gravity anomaly processed under the control of 3D seismic data fits well with the known seismic interpretation and wells. It makes the geological interpretation more reliable.

Parametric study of electrostatic separation of South African fine coal

The fact that water requirements are a major problem for present and future developments in material beneficiation, and the construction of a new power plant in South Africa, forms the basis for the utilization of a Rotary Triboelectrostatic Separator (RTS) for beneficiation of South African pulverized coal. The cleaning potential of Majuba and Koorfontein coal was first evaluated using kinetic froth flotation tests on the -177 μm coal fraction. The RTS tests were conducted under varied process parameters. Parameters such as applied separating voltage, air injection velocity, particle feed rate and splitter position were investigated. Two stage separation results show that the RTS reduced Majuba coal initially containing about 30% ash to a clean product of 14.30%, or 19.46%, ash at a combustible recovery of 15.10%, or 53.02%, respectively. Similar separation performance was also achieved with the Koorfontein coal. The mineral and organic compositions in the feed, after single stage and after the second stage separations were characterized using X-ray diffraction analysis. The results show a better separation for the second stage coal products.

Method Development of Enantiomer Separations by Affinity Capillary Electrophoresis,Cyclodextrin Electrokinetic Chromatography and Capillary Electrophoresis-Mass Spectrometry

Capillary electrophoresis (CE) has become a powerful tool for enantiomer separations during the last decade. Since 1993, the author has investigated enantiomer separations by affinity capillary electrophoresis (affinity CE) with some proteins and by cyclodextrin electrokinetic chromatography (CDEKC) with some charged cyclodextrins (CDs). Many successful enantiomer separations are demonstrated from our study in this review article. In the enantiomer separations by affinity CE, the deterioration of detection sensitivity was observed under high concentration of the protein in running solutions. The partial filling technique was practically useful to solve the serious problem. It allowed operation at high protein concentrations, such as 500 μmol/L, without the detection problem. Charged CDs had several advantages for the enantiomer separations over neutral ones. Strong electrostatic interactions between a charged CD and oppositely charged analytes should be effective for the formation of the complex. A large difference in electrophoretic mobility between the free analyte and the inclusion complex should also enhance the enantiomeric resolution. In CE mass spectrometry (CE MS), the partial filling technique was applied to avoid the introduction of nonvolatile chiral selectors into the CE MS interface. By replacing the nonvolatile electrolytes in the running buffer by volatile ones, the separation conditions employed in CE with the UV detection method could be transferred to CE MS.

DEVELOPMENT OF FAST TWO-DIMENSIONAL HIGH-RESOLUTION DIRECTION-FINDING TECHNIQUES

A fast separable approach based on a cross array is presented, which has coarsegrained parallelism. Its computational load is far less than that of the two-dimensional (2-D) direct processing method and other existing separable approaches. In order to compensate for the performance degradation due to separable processing, two postprocessing schemes are also proposed. Some computer simulation results are provided for illustration in the end.

Quantitatively probing interactions between membrane with adaptable wettability and oil phase in oil/water separation

The membrane method based on adaptive wettability shows great advantages in oil-water separation.At present,researches focus on the excellent application performance of the membrane material,while the quantitative analysis of interactions in oil-water separation is rarely recognized.Herein,we constructed an adaptable wettability membrane with multiple polymer networks by polydopamine(PDA)and mussel-inspired amphiphilic polymer.Based on the Owens three-probe liquid method,the surface energy of the modified membrane was verified to meet the adaptive wettability conditions,with surface energies(γ-8)of 147.6 mJ m^(−2)(superhydrophilic/underwater superoleophobic)and 49.87 mJ m^(−2)(superhydrophobic/superoleophobic),respectively.The adhesion or repulsion of the membrane to the oil phase under different conditions during the separation process was quantified by the chemical probe AFM technique.In addition,the oil-water selective separation mechanism was further analyzed in a simplified membrane microchannel model.The results show that the different wetting produces capillary additional pressure in opposite directions,resulting in different energies to be overcome when the oil or water passes through the microchannels,thus achieving selective separation.

A review on the extraction and separation of andrographolide from Andrographis paniculata:extraction selectivity,current challenges and strategies

Andrographolide is the main active ingredient of Andrographis paniculata(Burm.f.)Nees,known as“natural antibiotic”.Here,for the purpose of discovering a more efficient,low-cost extraction and separation method,the research status of andrographolide was reviewed.At present,researches only take extraction rate as the only index to optimize extraction parameters,but ignores the importance of extraction selectivity.It is usually meaningless to blindly pursue the extraction rate without considering the difficulty and cost of subsequent separation.So,factors affecting extraction selectivity such as solvent choice,temperature and physicochemical effects caused by extraction technique itself,are first discussed.Different extraction techniques for andrographolide were discussed by comparing the selectivity,efficiency and cost of extraction.The separation procedures of andrographolide such as decolorization,impurity removal,crystallization,membrane separation,solid-phase extraction and partition chromatography and their challenges and possible strategies are also discussed.It is hoped that this review can provide guidance for researchers who are committed to advancing the field of andrographolide extraction and purification.

Mechanics Principle and Engineering Application of Split Layer and Bed Separation of Mining Overburden

To control land surface subsidence caused the underground mineral exploitation and the catastrophic phenomena such as serious damage of buildings, waterbodies, cultivated lands, railways, bridges caused by land subsidence, bed separation grouting technology of overburden is put forward. To provide theoretical support for the technology, the characteristics and the mechanics mechanism of mining overburden from layer-split to formation of bed separation are studied. On the basis of elastic sheet board theory, calculation formula of rock sheet deflection is presented, and the mechanics criteria of the separation formation and the calculation formula of bed separation volume are set up. Finally, the applications and technics of bed separation grout technology of mining overburden to control land subsidence in china are introduced.

A Short-Cut Design Technique to Batch Distillation Column

The effects of equipment parameters of batch distillation column on the yield proportion are discussed and analyzed, the relations between maximal yield proportion and the column equipment parameters are correlated, which not only can be used to appraise rationality of the design parameters of the columns being employed and which but also can be used to new batch distillation column design. Under the assistance of the separation difficulty defined in this paper, the minimum number of theoretical plates is determined by the limit loss proportion method given, and further the actual number of theoretical plates and the height for the batch distillation are calculated by using the redundancy coefficient found to complete the whole design of the batch distillation as shown in the computational sample. Research showed that the actual number of theoretical plates and the height of batch distillation column with the column diameter 0.6 m are 17 and 5.1 m in alcohol mixture separation system of the sample proposed. Moreover, the approach can be extended to the design of batch distillation column with a separation system of multi-component liquid mixture after those adjacent components are treated as numerous binary component systems.