A novel method for determining the resistivity of compressed superconducting materials

The measurement of resistivity in a compressed material within a diamond anvil cell presents significant challenges.The high-pressure exper-imental setup makes it difficult to directly measure the size changes induced by pressure in the three crystallographic directions of the sample.In this study,we introduce a novel and effective method that addresses these technical challenges.This method is anticipated to offer a valuable foundation for high-pressure investigations on quantum materials,particularly those with anisotropic layered structures.

Dual-phase coexistence enables to alleviate resistance drift in phase-change films

The amorphous phase-change materials with spontaneous structural relaxation leads to the resistance drift with the time for phase-change neuron synaptic devices. Here, we modify the phase change properties of the conventional Ge_2Sb_2Te_5(GST) material by introducing an SnS phase. It is found that the resistance drift coefficient of SnS-doped GST was decreased from 0.06 to 0.01. It can be proposed that the origin originates from the precipitation of GST nanocrystals accompanied by the precipitation of SnS crystals compared to single-phase GST compound systems. We also found that the decrease in resistance drift can be attributed to the narrowed bandgap from 0.65 to 0.43 eV after SnS-doping. Thus, this study reveals the quantitative relationship between the resistance drift and the band gap and proposes a new idea for alleviating the resistance drift by composition optimization, which is of great significance for finding a promising phase change material.

Numerical Simulation of the Parallel Gap Resistance Welding Process of a Solar Cell and Mo/Pt/Ag Interconnector

Energy for space vehicles in low Earth orbit(LEO) is mainly generated by solar arrays, and the service time of the vehicles is controlled by the lifetime of these arrays, which depends mainly on the lifetime of the interconnects. To increase the service life of LEO satellites, molybdenum/platinum/silver(Mo/Pt/Ag) laminated metal matrix composite(LMMC) interconnectors are widely used in place of Mo/Ag LMMC and Ag interconnectors in solar arrays. A 2D thermal-electrical-mechanical coupled axisymmetric model was established to simulate the behavior of the parallel gap resistance welding(PGRW) process for solar cells and Mo/Pt/Ag composite interconnectors using the commercial software ANSYS. The direct multicoupled PLANE223 element and the contact pair elements TARGE169 and CONTA172 were employed. A transitional meshing method was applied to solve the meshing problem due to the ultrathin(1 μm) intermediate Pt layer. A comparison of the analysis results with the experimental results revealed that the best parameters were 60 W, 60 ms, and 0.0138 MPa. The voltage and current predicted by the finite element method agreed well with the experimental results. This study contributes to a further understanding of the mechanism of PGRW and provides guidance for finite element simulation of the process of welding with an ultrathin interlayer.

A Provable Positivity-Preserving Local Discontinuous Galerkin Method for the Viscous and Resistive MHD Equations

In this paper,we construct a high-order discontinuous Galerkin(DG)method which can preserve the positivity of the density and the pressure for the viscous and resistive magnetohydrodynamics(VRMHD).To control the divergence error in the magnetic field,both the local divergence-free basis and the Godunov source term would be employed for the multi-dimensional VRMHD.Rigorous theoretical analyses are presented for one-dimensional and multi-dimensional DG schemes,respectively,showing that the scheme can maintain the positivity-preserving(PP)property under some CFL conditions when combined with the strong-stability-preserving time discretization.Then,general frameworks are established to construct the PP limiter for arbitrary order of accuracy DG schemes.Numerical tests demonstrate the effectiveness of the proposed schemes.

Progressive Collapse Resistance of a New Staggered Story Isolated System

A new staggered isolated system developed from the mid-story isolated system is the new staggered story isolated system. There are not many studies on this structure currently. In this study, an 18-story new staggered story isolated system model is established using SAP2000. The dynamic nonlinear dynamic alternate method is used to analyze the structure against progressive collapse. Results show that the structure has good resistance to progressive collapse, and there is no progressive collapse under each working condition. The progressive collapse does not occur for the case of removing only one vertical structural member of the new staggered of isolated system. The side column has big influence on this isolated structures’ progressive collapse;the removal of vertical structural member of the isolation layer has less impact on the structure than the removal of the bottom vertical structural member. After the removing of the member, the internal force of the structure will be redistributed, and the axial force of the adjacent columns will change obviously, showing a trend of “near large and far small”.

Application of the Electrical Resistivity Method in Precision Agriculture of Coffee Cultivation, in the Kabiri Area, Ícolo e Bengo Township, Luanda, Angola

The electrical resistivity method is a geophysical tool used to characterize the subsoil and can provide an important information for precision agriculture. The lack of knowledge about agronomic properties of the soil tends to affect the agricultural coffee production system. Therefore, research related to geoelectrical properties of soil such as resistivity for characterization the region of the study for coffee cultivation purposes can improve and optimize the production. This resistivity method allows to investigate the subsurface through different techniques: 1D vertical electrical sounding and electrical imaging. The acquisition of data using these techniques permitted the creation of 2D resistivity cross section from the study area. The geoelectrical data was acquired by using a resistivity meter equipment and was processed in different softwares. The results of the geoelectrical characterization from 1D resistivity model and 2D resistivity electrical sections show that in the study area of Kabiri, there are 8 varieties of geoelectrical layers with different resistivity or conductivity. Near survey in the study area, the lowest resistivity is around 0.322 Ω·m, while the highest is about 92.1 Ω·m. These values illustrated where is possible to plant coffee for suggestion of specific fertilization plan for some area to improve the cultivation.

Establishment and Application of Identification Methods for Resistance to Sugarcane White Leaf Disease(SCWL)

[Objectives]This study was conducted to establish simple, efficient, stable, standardized and practical identification methods for sugarcane resistance to white leaf disease(SCWL), and promote the breeding for sugarcane resistance to SCWL. [Methods]The identification technology of sugarcane resistance to SCWL was systematically studied and explored from the aspects of sugarcane material treatment and planting, inoculation liquid preparation, inoculation method, disease investigation, grading standard formulation, etc., and two sets of simple, efficient, stable, standardized and practical accurate identification methods for sugarcane resistance to SCWL were created for the first time, namely, the seed cane coating inoculation method and the stem-cutting inoculation method at the growth stage. The seed cane coating inoculation method includes the steps of directly screening SCWL phytoplasma, extracting juice from cane and adding 10 times of sterile water to prepare an inoculation liquid, spraying seed cane on plastic film to keep moisture, planting the inoculated materials in barrels in an insect-proof greenhouse for cultivation, investigating the incidence rate 30 d after inoculation, and evaluating the disease resistance according to the 1-5 level standard. The method of stem-cutting inoculation includes the steps of directly screening sugarcane stems carrying SCWL phytoplasma and adding 10 times of sterile water to prepare an inoculation liquid, cultivating the identification materials in an insect-proof greenhouse, dropping 100 μl of the inoculation liquid into each root incision with a pipette gun at the age of 6 months, investigating the incidence rate 20 d after planting, and evaluating the disease resistance according to the 1-5 level standard. [Results] The two methods are similar to the natural transmission method. After inoculation, SCML occurred significantly, with high sensitivity and good reproducibility. The results of resistance identification were consistent with those of natural disease in the field. Through the two inoculation methods and field natural disease investigation, the resistance of 10 main cultivars to SCML was identified, which was true and reliable. [Conclusions] This study can provide standard varieties for identification of SCML resistance in the future.

Research Progress and Identification Method of Apple Stress Resistance

In the research, changes of apple chemistry, and molecule, under stresses, are n terms of morphology, physiology, bio- illustrated and research and identifica- tion methods of apple resistance are explored involving drought-resistance, flood-re- sistance, salt-stress resistance, cold-hardiness and heat-resistance. In addition prospects of apple resistance research are proposed, as well.

Synthesis of CA_(6)/AlON composite with enhanced slag resistance

Different amounts of AlON have been introduced in calcium hexaaluminate(CA_(6)) using two approaches, that is, one-step and twostep methods, to improve the slag resistance of CA_(6). A one-step method can directly sinter the mixtures combining Al_(2)O_(3), CaCO_(3), and Al in flowing nitrogen, in which AlON clusters are always formed because of the poor wettability of Al by Al_(2)O_(3), leading to the high porosity of CA_(6)/AlON composite. In a two-step method, CA_(6)and AlON are prepared separately and then mixed and sintered in flowing nitrogen. Compared with the sample prepared by the one-step method, CA_(6)and AlON in composite by the two-step method are more uniformly distributed,and the optimized amount of AlON added is 10wt%. The slag corrosion and penetration test shows that the CA_(6)/AlON composite using the two-step method exhibits superior slag corrosion protection. The promoted effect of AlON on slag penetration and corrosion resistance is also discussed.

Clinical role and importance of fluorescence in situ hybridization method in diagnosis of H pylori infection and determination of clarithromycin resistance in H pylori eradication therapy

H pylori is etiologically associated with gastritis, gas-tric and duodenal ulcers, gastric adenocarcinoma and mucosa-associated lymphoid tissue (MALT) lymphoma. Eradicating H pylori may convert rapidly the outcome of related diseases with the use of more accurate diagnostic molecular tests. Indeed some of the tests cannot give the evidence of current infection; H pylori can be detected by noninvasive and invasive methods, the latter requiring an endoscopy. Eradication failure is a big problem in H pylori infection. Recently, clarithromycin resistance in H pylori strains is increasing and eradicati-on therapy of this bacterium is becoming more difficult. Molecular methods have frequently been applied besides phenotypic methods for susceptibility testing to detect clarithromycin resistance due to mutations in the 2143 and 2144 positions of 23S rRNA gene. Fluorescence in situ hybridization (FISH) method on paraffin embedded tissue is a rapid, accurate and cost-effective method for the detection of H pylori infection and to determine clarithromycin resistance within three hours according to the gold standards as a non-culture method. This method can also be applied to fresh biopsy samples and the isolated colonies from a culture of H pylori, detecting both the culturable bacillary forms and the coccoid forms of H pylori, besides the paraffin embedded tissue secti-ons. This technique is helpful for determining the bac-terial density and the results of treatment where clarith-romycin has been widely used in populations to increase the efficacy of the treatment and to clarify the treatment failure in vitro.

Microstructures and wear resistance of high boron and low carbon ferroalloy using hybrid powder/wire overlaying method

The high boron alloy surfacing layer was easily cracked due to its insufficient toughness by using hybrid powder/ wire overlaying method. In order to explore the cracked mechanism, the microstructures and the wear resistance of the samples with different boron contents were studied. Further, phases analysis, microhardness, macrohardness and wear test were also carried out. The boron content depended microstructures were observed. The precipitation of the Fe2B, Fe3 （ C, B）, Fe23 （C, B）6 were increased with the increase of boron content. It was found that the wear resistance was independent of the macrohardness as the macrohardness increased firstly and then remained steady at -62 HRC. However, the wear resistance was depended on the boron contents, and which increased with the increase of the boron contents. The abrasive loss mechanism changed from plastic deformation removal to fracture removal.

An electrochemical method for evaluating the resistance to cathodic disbondment of anti-corrosion coatings on buried pipelines

Methods for evaluating the resistance to cathodic disbondment （RCD） of anti-corrosion coatings on buried pipelines were reviewed. It is obvious that these traditional cathodic disbondment tests （CDT） have some disadvantages and the evaluated results are only simple figures and always rely on the subjective experience of the operator. A new electrochemical method for evaluating the RCD of coatings, that is, the potentiostatic evaluation method （PEM）, was developed and studied. During potentiostatic anodic polarization testing, the changes of stable polarization current of specimens before and after cathodic disbonding （CD） were measured, and the degree of cathodic disbondment of the coating was quantitatively evaluated, among which the equivalent cathodic disbonded distance AD was suggested as a parameter for evaluating the RCD. A series of testing parameters of the PEM were determined in these experiments.

On-line Measurement for Ohmic Resistance in Direct Methanol Fuel Cell by Current Interruption Method

Electrochemical impedance spectroscopy (EIS) is widely used in fuel cell impedance analysis. However, for ohmic resistance (R Ω), EIS has some disadvantages such as long test period and complex data analysis with equivalent circuits. Therefore, the current interruption method is explored to measure the value of RΩ in direct methanol fuel cells (DMFC) at different temperatures and current densities. It is found that RΩ decreases as temperature increase, and decreases initially and then increases as current density increases. These results are consistent with those measured by the EIS technique. In most cases, the ohmic resistances with current interruption (R iR ) are larger than those with EIS (R EIS ), but the difference is small, in the range from –0.848% to 5.337%. The errors of R iR at high current densities are less than those of R EIS . Our results show that the R iR data are reliable and easy to obtain in the measurement of ohmic resistance in DMFC.

Study on Wave Added Resistance of a Deep-V Hybrid Monohull Based on Panel Method

In this paper, a panel method based on three dimensional potential flow theory is used to study the problem of wave added resistance. The time-domain motion response of Wigely III ship in head waves is calculated by AQWA, and then the wave added resistance of ship is obtained by near-field pressure integration method. By comparing the calculated results with the experimental data in literature, it is shown that the variation trend and peak value are in good agreement, and the accuracy and efficiency meet the research requirements. Based on the above mentioned method, the wave added resistance of a deep-V hybrid monohull in head waves is studied. The motions and wave added resistances of the deep-V hybrid monohull and the deep-V original ship advancing in head waves with various forward speed and wave frequencies are calculated and analyzed. The results show that the longitudinal motion response of the deep-V hybrid monohull is effectively suppressed and the wave added resistance is obviously reduced, the new type of ship has good engineering application prospects. The present method provides an approach of satisfactory accuracy and efficiency to predict wave added resistance of ships voyaging in waves.

Evaluation method of cracking resistance of lightweight aggregate concrete

The cracking behavior of lightweight aggregate concrete(LWAC) was investigated by mechanical analysis, SEM and cracking-resistant test where a shrinkage-restrained ring with a clapboard was used. The relationship between the ceramsite type and the cracking resistance of LWAC was built up and compared with that of normal-weight coarse aggregate concrete(NWAC). A new method was proposed to evaluate the cracking resistance of concrete, where the concepts of cracking coefficient ζt(t) and the evaluation index Acr(t) were proposed, and the development of micro-cracks and damage accumulation were recognized. For the concrete with an ascending cracking coefficient curve, the larger Acr(t) is, the lower cracking resistance of concrete is. For the concrete with a descending cracking coefficient curve, the larger Acr(t) is, the stronger the cracking resistance of concrete is. The evaluation results show that in the case of that all the three types of coarse aggregates in concrete are pre-soaked for 24 h, NWAC has the lowest cracking resistance, followed by the LWAC with lower water absorption capacity ceramsite and the LWAC with higher water absorption capacity ceramsite has the strongest cracking resistance. The proposed method has obvious advantages over the cracking age method, because it can evaluate the cracking behavior of concrete even if the concrete has not an observable crack.

The Method for Measuring the Loop Resistance and the Temperature Rise Calculation of GIS Conductor Pole

This paper studies the method for measuring the loop resistance of GIS conductor pole based on the super capacitor producing impulse current up to several thousand amperes. This method overcomes the limitations of conventional diagnostic method. Typical GIS conductor poles are chosen. Based on FEA and lab tests, the effect of different forms of current and contact condition, relationship between the temperature of contact and the loop resistance is researched. In full- scale testing under realistic operating conditions on the new 220 kV GIS using prototype instrumentation a very good sensitivity in an early stage was obtained.

Probabilistic limit state design methodof the axial resistance of post grouting pile

The reliability of post grouting pile axial resistance was studied by proposing a design method for its probabilistic limit state,which is represented by the partial coefficients of load,end,and side resistance.The hyperbolic,modified hyperbolic,and polynomial models were employed to predict the ultimate bearing capacity of test piles that were not loaded to damage in field tests.The results were used for the calculation and calibration of the reliability index.The reliability of the probabilistic limit state design method was verified by an engineering case.The results show that the prediction results obtained from the modified hyperbolic model are closest to those obtained through the static load test.The proposed corresponding values of total,side,and end resistance partial coefficients are 1.84,1.66,and 2.73 when the dead and live load partial coefficients are taken as 1.1 and 1.4,respectively.Meanwhile,the corresponding partial coefficients of total,side,and end resistance are 1.70,1.56,and 2.34 when the dead and live load partial coefficients are taken as 1.2 and 1.4,respectively.

Research and Application of High-Density Resistivity Method in Seawater Intrusion Investigation in Laizhou Bay

The disaster of seawater intrusion seriously affects people's lives and restricts economic development,so the detection and treatment of seawater intrusion is a long-term task.On the basis of field investigation and water quality analysis,according to the change characteristics of apparent resistivity of groundwater after Cl-reaches 250 mg/L,the theoretical basis for the application of high-density resistivity method was determined,and the characteristic values of apparent resistivity for seawater intrusion interfaces in different geological characteristic regions in Laizhou Bay area were determined by typical profile tests.Combined with water quality investigation and other means,profiles for the high-density resistivity method were arranged,and the interfaces between saline and fresh water were accurately divided.

Test method and experimental research on resistance of oil shale under high temperature

Heating the oil shale by current underground to accomplish in-situ transformation process, is a viable direction. The electrical properties of oil shale under different temperatures, especially the resistance, become important. Charging oil shale underground to heat oil shale till kerogen's decomposition temperature, then crude oil and other gases can be generated. The resistance of the oil shale samples was measured by Direct Current (DC) quadripole method to find out the variation rules of resistance value. In the experiments, oil shale presented its semiconductor property. When heated till 350℃-450℃, its resistance changed greatly, optional for heating and cracking. The porosity, oil content, media and composition affected the resistance largely.

Obtaining 2D Soil Resistance Profiles from the Integration of Electrical Resistivity Data and Standard Penetration Test (SPT) and Light Dynamic Penetrometer (DPL) Resistance Tests—Applications in Mass Movements Studies

In Brazil and various regions globally, the initiation of landslides is frequently associated with rainfall;yet the spatial arrangement of geological structures and stratification considerably influences landslide occurrences. The multifaceted nature of these influences makes the surveillance of mass movements a highly intricate task, requiring an understanding of numerous interdependent variables. Recent years have seen an emergence in scholarly research aimed at integrating geophysical and geotechnical methodologies. The conjoint examination of geophysical and geotechnical data offers an enhanced perspective into subsurface structures. Within this work, a methodology is proposed for the synchronous analysis of electrical resistivity geophysical data and geotechnical data, specifically those extracted from the Light Dynamic Penetrometer (DPL) and Standard Penetration Test (SPT). This study involved a linear fitting process to correlate resistivity with N10/SPT N-values from DPL/SPT soundings, culminating in a 2D profile of N10/SPT N-values predicated on electrical profiles. The findings of this research furnish invaluable insights into slope stability by allowing for a two-dimensional representation of penetration resistance properties. Through the synthesis of geophysical and geotechnical data, this project aims to augment the comprehension of subsurface conditions, with potential implications for refining landslide risk evaluations. This endeavor offers insight into the formulation of more effective and precise slope management protocols and disaster prevention strategies.