A general model for trailing edge serrations simulation on wind turbine airfoils

Trailing edge serrations(TESs)are capable of noticeably suppressing the turbulent trailing edge noise induced by rotating wind turbine blades and become an integral part of a blade.However,the challenges involved in the dimensional design of serration height 2 h,wavelengthλand flap angleϕare yet to be dealt with in a satisfactory manner.To address the problem,a general model for simulating the effects of serrations on the hydrodynamic and aeroacoustic performance is proposed due to its ease of use and relatively low requirements for user input.The solid serrations are replicated by momentum sources calculated by its aerodynamic forces.Then,a case relevant to wind turbine airfoil is examined,a hybrid improved delay detached eddy simulation(IDDES)method coupled with FW-H integration is deployed to obtain the flow features and far-field sound pressure level.It is found that the modeling method could reproduce the flow field and noise as serrated airfoil.

Effects of Si Addition on Microstructure,Properties and Serration Behaviors of Lightweight Al-Mg-Zn-Cu Medium-entropy Alloys

A series of as-cast lightweight multicomponent alloys Al(86-x)Mg10Zn2Cu2Six(x=0,0.3,0.6,0.9,1.2 at.%)were prepared by a vacuum induction furnace with a steel die.With the addition of Si,the reticular white Al-Cu phase deposited were gradually replaced by the gray eutectic Mg-Si phase,while the compressive strength of the alloys increases first and then decreases slowly.It is particularly noteworthy that the compression plasticity also exhibits this trend.When the Si content is 0.9 at.%,the compressive strength reaches its maximum at 779.11 MPa and the compressive plasticity reaches 20.91%.The effect of the addition of Si on the serration behavior of alloy was also studied;we found that the addition of Si introduces a new MgSi phase,and with the change of Si is significantly affects the morphology of the precipitated phase,which affects the serration behavior of the alloys.The comprehensive mechanical properties of the alloy are optimal at the critical point where the serration behavior disappears.In this work,we have provided a method and a composition for the preparation of a low-cost,high-strength,lightweight medium-entropy alloys.

Cycling Hardening and Serration Yielding of Fe-Ni-Cr Alloy at High Temperature under Out-phase TMF

Behaviour of hardening and serration yield of a Fe-Ni-Cr alloy under isothermal cycling （ISC） and out-phase TMF was studied on the basis of varied hysteresis loops. Cycling hardening and serrated yielding for ISC depend on the temperature and the total strain range, stronger hardening with serrated yielding at higher strain range under ISC at 600 ℃, but no hardening and serrated yielding occurred under ISC at 800 ℃. Stronger hardening with stress serration occurred at the thermal path going to the lowest temperature, no stress serration occurred at the highest temperature under the out-phase. The hardening also depends on the total strain range, higher total strain range with lower cycling temperature resulted in a stronger hardening and remarkable serration yielding behavior. Weaker hardening without serrated yielding occurred at near 800℃ may due to an obvious cycling stress drop under out-phase TMF. Change in the shape of the hysteresis loops also expresses the degree of the damage of the tested alloy under out-phase and ISC.

EFFECTS OF MODIFICATION OF THE CARBIDE CHARACTERISTICS THROUGH GRAIN BOUNDARY SERRATION ON CREEP-FATIGUE LIFE IN AUSTENITIC STAINLESS STEELS

Modification of the carbide characteristics through the grain boundary serration is investigated, using an AISI 316 and 304 stainless steels. In both steels, triangular carbides were observed at straight grain boundaries while planar carbides were observed at the serrated grain boundaries. The serrated grain boundary energy is observed to be much lower than that of the straight one. Therefore, the carbide morphology is found to be changed from triangular to planar along the serrated boundary to reduce the interfacial energy between the carbide and the matrix. The creep-fatigue properties of these steels at 873K have been investigated. The creep-fatigue life of the sample with planar carbide at the serrated grain boundary was found to be much longer than that with triangular carbide at the straight one. These results imply that the planar carbides with lower interfacial energy have higher cavitation resistance, resulting in the retardation of cavity nucleation and growth to increase creep-fatigue life.

Review on the plastic instability of medium -Mn steels for identifying the formation mechanisms of Lüders and Portevin -Le Chatelier bands

Plastic instability,including both the discontinuous yielding and stress serrations,has been frequently observed during the tensile deformation of medium-Mn steels(MMnS)and has been intensively studied in recent years.Unfortunately,research results are controversial,and no consensus has been achieved regarding the topic.Here,we first summarize all the possible factors that affect the yielding and flow stress serrations in MMnS,including the morphology and stability of austenite,the feature of the phase interface,and the deformation parameters.Then,we propose a universal mechanism to explain the conflicting experimental results.We conclude that the discontinuous yielding can be attributed to the lack of mobile dislocation before deformation and the rapid dislocation multiplication at the beginning of plastic deformation.Meanwhile,the results show that the stress serrations are formed due to the pinning and depinning between dislocations and interstitial atoms in austenite.Strain-induced martensitic transformation,influenced by the mechanical stability of austenite grain and deformation parameters,should not be the intrinsic cause of plastic instability.However,it can intensify or weaken the discontinuous yielding and the stress serrations by affecting the mobility and density of dislocations,as well as the interaction between the interstitial atoms and dislocations in austenite grains.

Particle-Image Velocimetry and Force Measurements of Leading-Edge Serrations on Owl-Based Wing Models

High-resolution Particle-Image Velocimetry （PIV） and time-resolved force measurements were performed to analyze the impact of the comb-like structure on the leading edge of barn owl wings on the flow field and overall aerodynamic performance. The Reynolds number was varied in the range of 40,000 to 120,000 and the range of angle of attack was 0° to 6° for the PIV and -15° to ＋20° for the force measurements to cover the full flight envelope of the owl. As a reference, a wind-tunnel model which possessed a geometry based on the shape of a typical barn owl wing without any owl-specific adaptations was built, and measurements were performed in the aforementioned Reynolds number and angle of attack： range. This clean wing model shows a separation bubble in the distal part of the wing at higher angles of attack. Two types of comb-like structures, i.e., artificial serrations, were manufactured to model the owl＇s leading edge with respect to its length, thickness, and material properties. The artificial structures were able to reduce the size of the separation region and additionally cause a more uniform size of the vortical structures shed by the separation bubble within the Reynolds number range investigated, resulting in stable gliding flight independent of the flight velocity. However, due to increased drag coefficients in conjunction with similar lift coefficients, the overall aerodynamic performance, i.e., lift-to-drag ratio is reduced for the serrated models. Nevertheless, especially at lower Reynolds numbers the stabilizing effect of the uniform vortex size outperforms the lower aerodynamic performance.

Noise Reduction of UAV Using Biomimetic Propellers with Varied Morphologies Leading-edge Serration

The Leading-Edge(LE)serrations on owls'wings are known to be responsible for silent flight.However,this design has rarely been applied to reduce the noise of rotational rotor propellers and the morphologies of the existing serration designs are diverse.Here,we present a comparative study ofLE serrations with different morphologies in terms of the effectiveness in suppressing noise and promoting thrust forces.The performances of biomimetic propellers are investigated by Computational Fluid Dynamics(CFD)simulations and rotation experiments.The simulation results reveal that LE serrations could reduce velocity fluctuations and change the lamina-turbulent transition and turbulence distribution on the suction surface of propeller,but the morphology of the serrations influences its effectiveness.Rotation testing results indicate that the sawtooth propeller has the best performance on noise reduction(on average 2.43 dB and in maximum 4.18 dB)and simultaneously enhancing the thrust forces(3.53%).The largest practical noise reductions(4.73 dB and 3.79 rdB)using the sawtooth propeller are observed when the quad-rotor Unmanned-Aerial Vehicle(UAV)is hovering at heights of 5 m and 8 m,respectively.Our results indicate the robustness and usefulness of owl-inspired biomimetic serration devices for aero-acoustic control and aerodynamic performance promotion on propeller designs.This finding is expected to con^bute to suppressing the sound of propeller and the rotor-based aircraft.

Morphology Effects of Leading-edge Serrations on Aerodynamic Force Production： An Integrated Study Using PIV and Force Measurements

While the leading-edge serration in owls＇ wing is known to be responsible for low noise gliding and flapping flights, the findings on its aero-acoustic role have been diverse or even controversial. Here we present an experimental study of the morphological effects of leading-edge serrations on aerodynamic force production by utilizing owl-inspired, single-feather, clean and serrated wing models with different serration lengths and spacing, and by combining Particle Image Velocimetry （PIV） and force measurements. Force measurements show that an increase in the length and density of the leading-edge serrations leads to a reduction in the lift coefficient and lift-to-drag ratio at Angles of Attack （AoAs） 〈 15° whereas the clean and serrated wings achieve comparable aerodynamic performance at higher AoAs 〉 15°, which owl wings often reach in flight. Furthermore PIV visualization of the flow fluctuations demonstrates that the leading-edge serration-based mechanism is consistent in all serrated wing models in terms of passive control of the laminar-turbulent transition while at AoAs 〉 15° similar suction flow is present at leading edge resulting in a comparable aerodynamic performance to that of the clean wing. Our results indicate the robustness and usefulness of leading-edge serration-inspired devices for aero-acoustic control in biomimetic rotor designs.

AtNSF regulates leaf serration by modulating intracellular trafficking of PIN1 in Arabidopsis thaliana

In eukaryotes,N-ethylmaleimide-sensitive factor(NSF)is a conserved AAA+ATPase and a key component of the membrane trafficking machinery that promotes the fusion of secretory vesicles with target membranes.Here,we demonstrate that the Arabidopsis thaliana genome contains a single copy of NSF,At NSF,which plays an essential role in the regulation of leaf serration.The At NSF knock-down mutant,atnsf-1,exhibited more serrations in the leaf margin.Moreover,polar localization of the PINFORMED1(PIN1)auxin efflux transporter was diffuse around the margins of atnsf-1 leaves and root growth was inhibited in the atnsf-1 mutant.More PIN1-GFP accumulated in the intracellular compartments of atnsf-1 plants,suggesting that At NSF is required for intracellular trafficking of PIN between the endosome and plasma membrane.Furthermore,the serration phenotype was suppressed in the atnsf-1 pin1-8 double mutant,suggesting that At NSF is required for PIN1-mediated polar auxin transport to regulate leaf serration.The CUPSHAPED COTYLEDON2(CUC2)transcription factor gene is up-regulated in atnsf-1 plants and the cuc2-3 single mutant exhibits smooth leaf margins,demonstrating that At NSF also functions in the CUC2 pathway.Our results reveal that At NSF regulates the PIN1-generated auxin maxima with a CUC2-mediated feedback loop to control leaf serration.

A Brief Review of High Entropy Alloys and Serration Behavior and Flow Units

Multicomponent alloys with high entropy of mixing,e.g.,high entropy alloys（HEAs）and/or multiprincipal-element alloys（MEAs）,are attracting increasing attentions,because the materials with novel properties are being developed,based on the design strategy of the equiatomic ratio,multicomponent,and high entropy of mixing in their liquid or random solution state.Recently,HEAs with the ultrahigh strength and fracture toughness,excellent magnetic properties,high fatigue,wear and corrosion resistance,great phase stability/high resistance to heat-softening behavior,sluggish diffusion effects,and potential superconductivity,etc.,were developed.The HEAs can even have very high irradiation resistance and may have some self-healing effects,and can potentially be used as the first wall and nuclear fuel cladding materials.Serration behaviors and flow units are powerful methods to understand the plastic deformation or fracture of materials.The methods have been successfully used to study the plasticity of amorphous alloys（also bulk metallic glasses,BMGs）.The flow units are proposed as：free volumes,shear transition zones（STZs）,tension-transition zones（TTZs）,liquid-like regions,soft regions or soft spots,etc.The flow units in the crystalline alloys are usually dislocations,which may interact with the solute atoms,interstitial types,or substitution types.Moreover,the flow units often change with the testing temperatures and loading strain rates,e.g.,at the low temperature and high strain rate,plastic deformation will be carried out by the flow unit of twinning,and at high temperatures,the grain boundary will be the weak area,and play as the flow unit.The serration shapes are related to the types of flow units,and the serration behavior can be analyzed using the power law and modified power law.

Prevalence, risk factors, and BRAF mutation of colorectal sessile serrated lesions among Vietnamese patients

BACKGROUND Sessile serrated lesions(SSLs)are considered precancerous colorectal lesions that should be detected and removed to prevent colorectal cancer.Previous studies in Vietnam mainly investigated the adenoma pathway,with limited data on the serrated pathway.AIM To evaluate the prevalence,risk factors,and BRAF mutations of SSLs in the Vietnamese population.METHODS This is a cross-sectional study conducted on patients with lower gastrointestinal symptoms who underwent colonoscopy at a tertiary hospital in Vietnam.SSLs were diagnosed on histopathology according to the 2019 World Health Organi-zation classification.BRAF mutation analysis was performed using the Sanger DNA sequencing method.The multivariate logistic regression model was used to determine SSL-associated factors.RESULTS There were 2489 patients,with a mean age of 52.1±13.1 and a female-to-male ratio of 1:1.1.The prevalence of SSLs was 4.2%[95%confidence interval(CI):3.5-5.1].In the multivariate analysis,factors significantly associated with SSLs were age≥40[odds ratio(OR):3.303;95%CI:1.607-6.790],male sex(OR:2.032;95%CI:1.204-3.429),diabetes mellitus(OR:2.721;95%CI:1.551-4.772),and hypertension(OR:1.650,95%CI:1.045-2.605).The rate of BRAF mutations in SSLs was 35.5%.CONCLUSION The prevalence of SSLs was 4.2%.BRAF mutations were present in one-third of SSLs.Significant risk factors for SSLs included age≥40,male sex,diabetes mellitus,and hypertension.

Superficial Serrated Adenoma (SuSA): A New Subtype of Serrated Lesions

Superficial serrated adenoma (SuSA) is a new subtype of serrated lesions proposed in recent years, most of which are located in the sigmoid colon or rectum, with typical mixed adenoma and serrated pathological features, and its molecular features are high frequency of KRAS mutation and RSPO fusion or overexpression. At present, it is believed that SuSA has two subtypes: traditional serrated adenoma (TSA)-associated SuSA and isolated SuSA. Solitary SuSA showed faded pedicle-free protuberant lesions under endoscope and lobulated, pp (pit pattern) classification was type II and type IIIH, TSA-associated SuSA showed double-layer eminence, SuSA part showed white flat eminence, pp classification showed type II and IIIH, TSA part showed red tone high eminence, pp was IVH type. SuSA can develop into colorectal cancer through the evolution of TSA, and it can also directly develop into MSS colorectal cancer. In view of the superficial understanding of SuSA and the lack of a complete description of SuSA, this paper review the research progress of SuSA at home and abroad from the origin, endoscope features, histopathological features, molecular biology, differential diagnosis and treatment of SuSA, in order to better promote the understanding and clinical diagnosis of lesions.

Precision in detecting colon lesions:A key to effective screening policy but will it improve overall outcomes?

Colonoscopy is the gold standard for the screening and diagnosis of colorectal cancer,resulting in a decrease in the incidence and mortality of colon cancer.However,it has a 21%rate of missed polyps.Several strategies have been devised to increase polyp detection rates and improve their characterization and delimi-tation.These include chromoendoscopy(CE),the use of other devices such as Endo cuffs,and major advances in endoscopic equipment[high definition,magnification,narrow band imaging,i-scan,flexible spectral imaging color enhancement,texture and color enhancement imaging(TXI),etc.].In the retrospective study by Hiramatsu et al,they compared white-light imaging with CE,TXI,and CE+TXI to determine which of these strategies allows for better definition and delimitation of polyps.They concluded that employing CE associated with TXI stands out as the most effective method to utilize.It remains to be demonstrated whether these results are extrapolatable to other types of virtual CE.Additionally,further investigation is needed in order to ascertain whether this strategy could lead to a reduction in the recurrence of excised lesions and potentially lower the occurrence of interval cancer.

High-throughput investigations of configurational-transformation-dominated serrations in CuZr/Cu nanolaminates

Metallic amorphous/crystalline(A/C)nanolaminates exhibit excellent ductility while retaining their high strength.However,the underlying physical mechanisms and the resultant structural changes during plastic deformation still remain unclear.In the present work,the structure-property relationship of CuZr/Cu A/C nanolaminates is established through integrated high-throughput micro-compression tests and molecular dynamics simulations together with high-resolution transmission electron microcopy.The serrated flow of nanolaminates results from the formation of hexagonal-close-packed(HCP)-type stacking faults and twins inside the face-centered-cubic(FCC)Cu nano-grains,the body-centered-cubic(BCC)-type ordering at their grain boundaries,and the crystallization of the amorphous CuZr layers.The serration behavior of CuZr/Cu A/C nanolaminates is determined by several factors,including the formation of dense dislocation networks from the multiplication of initial dislocations that formed after yielding,weak-spots-related configurational-transitions and shear-transition-zone activities,and deformation-induced devitrification.The present work provides an insight into the heterogeneous deformation mechanism of A/C nanolaminates at the atomic scale,and mechanistic base for the microstructural design of self-toughening metallic-glass(MG)-based composites and A/C nanolaminates.

Effect of strain rate and temperature on the serration behavior of SA508-Ⅲ RPV steel in the dynamic strain aging process

Dynamic strain aging （DSA） effect on SA508-III reactor pressure vessel （RPV） steel was investigated. The SA508-III RPV steel was subjected to tension tests at different strain rates （1.1× 10-5 s-1 and 6.6× 10-5 s-1） and different temperatures （500 and 550 ℃） to evaluate the influence of strain rate and temperature on the serrated flow behavior, which is the repetitive and discontinuous yielding phenomenon on the stress-strain curves. The higher temperature leads to the higher density of precipitates, M23C6 carbides and needle-like Mo2C carbides. It was found that the samples under tension test of 6.6 × 10-5 s-1 and 500 ℃ possess superior mechanical properties and mainly show A-type serrations on the tension test curves. Then, the local regress method was used to filter the DSA curves, thus to show the real trend of the curves. It has been found that the less time of interaction between dislocations and precipitates under higher strain rates leads to a higher strength of the sample. The more tiny-stress drops on the 550 ℃ serration curve can be attributed to the hardening phase, M23C6 carbides and needle-like Mo2C carbides. The higher percentage of the small stress drops on the serration curves represents the higher mechanical strength.

Statistical analysis on strain-rate effects during serrations in a Zr-based bulk metallic glass

By means of statistical analysis,the deformation mechanisms taking place in elastic loading and plastic shearing stages during serrated flows on the stress-strain curves for bulk metallic glasses were studied comprehensively.Normalized serration number presented a linear increasing tendency with the decrease of applied strain rates due to the reduction of free volumes.An excellent plastic deformation was illustrated from the influences of structure arrangement with activation energy.By using mean-field theory（MFT）,maximum elastic-energy density at different strain rates could be predicted by MFT besides maximum stress drops during serrations.These results were helpful for understanding the serrated flow behavior or designing decent schemes to improve the plasticity of bulk metallic glasses at room temperature.

Effect of pre-existing shear bands on mechanical properties and serration behaviors in bulk metallic glasses

Pre-existing（multiple）shear bands were introduced into the ductile Zr56Co28Al16 and Zr65Ni10Cu15Al10bulk metallic glasses（BMGs）through the lateral-deformation,respectively.It was found that the pre-exiting shear bands can further enhance the compressive plasticity of ductile BMGs.According to the serration analysis on the plastic deformation of the as-cast and the pre-deformed samples,the serration events in the stress-strain curves during deformation display a self-organized critical（SOC）behavior.Compared with the as-cast BMGs,a larger power-law scaling exponent calculated based on serrated flow behaviors becomes larger for the pre-deformed BMGs,implying that the shear banding stability of BMGs is effectively enhanced.This should be caused by the pronounced interactions of shear bands during plastic deformation for the pre-deformed BMGs.However,by introducing a large amount of multiple shear bands into the glassy matrix,it also becomes easier for shear bands to propagate along the pre-existing shear bands,leading to a lower cut-off elastic energy density for the pre-deformed BMGs.More multiple shear bands with stronger interactions for the pre-deformed BMGs could provide a larger chance to activate the shear-band cracking but less local elastic energies are remained for the subsequent crack-linking.

Serration Behavior in Zr-Cu-Al Glass-forming Systems

The metallic glass matrix composites（MGMCs）and bulk metallic glasses（BMGs）were studied by statistical analysis during plastic deformation at the strain rates of 2×10^-2,2×10^-3,and 2×10^-4 s^-1,respectively.No serration events occur in both MGMCs and BMGs during compression tests at the strain rate of 2×10^-2 s^-1.When deformed at the strain rate of 2×10^-3 s^-1,the BMG displays a larger plasticity,which is due to the larger serration events followed by a series of small serrations caused by the continuous movement of free volume.The amplitudes and elastic-energy densities increase with increasing the strain rates owing to many serrations in MGMCs.It is deduced that the Young′s modulus decreases from the normalized stress drop and fluctuations are observed on stressstrain curves,which is attributed to a lower coefficient according to the stick-slip model.

Serration and Noise Behavior in Advanced Materials

The Chinese Materials Research Society（C-MRS）Conference（2015）was held in the Guizhou Park Hotel International Conference Center,Guiyang,China,from July 10-14,2015.This conference consists of 30symposia,including 4international symposia.As one of 4international symposia,＂Serration and noise behavior in advanced materials＂

Serration and shear avalanches in a ZrCu based bulk metallic glass composite in different loading methods

In the current research, serrated flow is investigated under tensile and compressive loading in a ZrCubased bulk metallic glass composite (BMGC) that is well known for its plastic deformability, which is higher than that of metallic glasses. Statistical analysis on serrations shows a complex, scale free process, in which shear bands are highly correlated. The distribution of the elastic-energy density stored in each serration event follows a power-law relationship, showing a randomly generated serrated event under both tension and compression tests. The plastic deformation in the temporal space is explored by a timeseries analysis, which is consistent with the trajectory convergent evolution in critical dynamic behavior even in the low strain rate regime in both tests. The results demonstrate that the secondary phase in the BMGC can stabilize the shear band extension and facilitate the critical behavior in the low strain rate regime. This study provides a strong evidence of serrated flow phenomenon in BMGC under tension test, and offers a deep understanding of the correlation between serrations and shear banding in temporal space.