Influence of pier height on the safety of trains running on high-speed railway bridges during earthquakes

Sudden earthquakes pose a threat to the running safety of trains on high-speed railway bridges,and the stiffness of piers is one of the factors affecting the dynamic response of train-track-bridge system.In this paper,a experiment of a train running on a high-speed railway bridge is performed based on a dynamic experiment system,and the corresponding numerical model is established.The reliability of the numerical model is verified by experiments.Then,the experiment and numerical data are analyzed to reveal the pier height effects on the running safety of trains on bridges.The results show that when the pier height changes,the frequency of the bridge below the 30 m pier height changes greater;the increase of pier height causes the transverse fundamental frequency of the bridge close to that of the train,and the shaking angle and lateral displacement of the train are the largest for bridge with 50 m pier,which increases the risk of derailment;with the pier height increases from 8 m to 50 m,the derailment coefficient obtained by numerical simulations increases by 75% on average,and the spectral intensity obtained by experiments increases by 120% on average,two indicators exhibit logarithmic variation.

Reliability-based life-cycle cost seismic design optimization of coastal bridge piers with nonuniform corrosion using different materials

Reinforcement corrosion is the main cause of performance deterioration of reinforced concrete(RC)structures.Limited research has been performed to investigate the life-cycle cost(LCC)of coastal bridge piers with nonuniform corrosion using different materials.In this study,a reliability-based design optimization(RBDO)procedure is improved for the design of coastal bridge piers using six groups of commonly used materials,i.e.,normal performance concrete(NPC)with black steel(BS)rebar,high strength steel(HSS)rebar,epoxy coated(EC)rebar,and stainless steel(SS)rebar(named NPC-BS,NPC-HSS,NPC-EC,and NPC-SS,respectively),NPC with BS with silane soakage on the pier surface(named NPC-Silane),and high-performance concrete(HPC)with BS rebar(named HPC-BS).First,the RBDO procedure is improved for the design optimization of coastal bridge piers,and a bridge is selected to illustrate the procedure.Then,reliability analysis of the pier designed with each group of materials is carried out to obtain the time-dependent reliability in terms of the ultimate and serviceability performances.Next,the repair time of the pier is predicted based on the time-dependent reliability indices.Finally,the time-dependent LCCs for the pier are obtained for the selection of the optimal design.

Identity and Identification: William Langland Wrote The Romance of William of Palerne

This essay shows that William Langland/Longe Wille wrote The Romance of William of Palerne.It brings forward evidence from its text in two main ways:(1).synchronically,i.e.across the text;and(2).diachronically,‘across time’.There is a comparison between this c.1360-61 work and the previous 1191-4 NE Old French/Picard poem Le Roman de Guillaume de Palerne specifically of three passages from each.

Numerical Simulation of the Influence of Water Flow on the Piers of a Bridge for Different Incidence Angles

A two-dimensional mathematical model is used to simulate the influence of water flow on the piers of a bridge for different incidence angles.In particular,a finite volume method is used to discretize the Navier-Stokes control equations and calculate the circumferential pressure coefficient distribution on the bridge piers’surface.The results show that the deflection of the flow is non-monotonic.It first increases and then decreases with an increase in the skew angle.

Seismic damage analysis of the outlet piers of arch dams using the finite element sub-model method

This study aims to analyze seismic damage of reinforced outlet piers of arch dams by the nonlinear finite element （FE） sub-model method. First, the dam-foundation system is modeled and analyzed, in which the effects of infinite foundation, contraction joints, and nonlinear concrete are taken into account. The detailed structures of the outlet pier are then simulated with a refined FE model in the sub-model analysis. In this way the damage mechanism of the plain （unreinforced） outlet pier is analyzed, and the effects of two reinforcement measures （i.e., post-tensioned anchor cables and reinforcing bar） on the dynamic damage to the outlet pier are investigated comprehensively. Results show that the plain pier is damaged severely by strong earthquakes while implementation of post-tensioned anchor cables strengthens the pier effectively. In addition, radiation damping strongly alleviates seismic damage to the piers.

ML and CFD Simulation of Flow Structure around Tandem Bridge Piers in Pressurized Flow

Various regions are becoming increasingly vulnerable to the increased frequency of floods due to the recent changes in climate and precipitation patterns throughout the world.As a result,specific infrastructures,notably bridges,would experience significant flooding for which they were not intended and would be submerged.The flow field and shear stress distribution around tandem bridge piers under pressurized flow conditions for various bridge deck widths are examined using a series of three-dimensional(3D)simulations.It is indicated that scenarios with a deck width to pier diameter(Ld/p)ratio of 3 experience the highest levels of turbulent disturbance.In addition,maximum velocity and shear stresses occur in cases with Ld/p equal to 6.Results indicate that increasing the number of piers from 1 to 2 and 3 results in the increase of bed shear stress by 24%and 20%respectively.Finally,five machine learning algorithms,including Decision Trees(DT),Feed Forward Neural Networks(FFNN),and three Ensemble models,are implemented to estimate the flow field and the turbulent structure.Results indicated that the highest accuracy for estimation of U,and W,were obtained using AdaBoost ensemble with R2=0.946 and 0.951,respectively.Besides,the Random Forest algorithm outperformed AdaBoost slightly in the estimation of V and turbulent kinetic energy(TKE)with R2=0.894 and 0.951,respectively.

Hysteretic behavior of post-tensioned precast segmental CFT double-column piers

Considering the desirable behavior of concrete filled steel tube(CFT)columns and the complicated behavior of segmental double-column piers under cyclic loads,three post-tensioned precast segmental CFT double-column pier specimens were tested to extend their application in moderate and high seismicity areas.The effects of the number of CFT segments and the steel endplates as energy dissipaters on the seismic behavior of the piers were evaluated.The experimental results show that the segmental piers exhibited stable hysteretic behavior with small residual displacements under cyclic loads.All the tested specimens achieved a drift ratio no less than 13%without significant damage and strength deterioration due to the desirable behavior of CFT columns.Since the deformation of segmental columns was mainly concentrated at the column-footing interfaces,the increase of the segment numbers for each column had no obvious effects on the loading capacity but reduced the initial stiffness of the specimens.The use of steel endplates improved the bearing capacity,stiffness and energy dissipation of segmental piers,but weakened their self-centering capacity.Fiber models were also proposed to simulate the hysteretic behavior of the tested specimens,and the influences of segment numbers and prestress levels on seismic behavior were further studied.

Design and Engineering of Urban Interchange Ramp Bridge Structure

This paper analyzes the structural design of an urban interchange ramp bridge from four aspects,which are the superstructure,pier structure,foundation structure,and deck structure design to summarize the structural design ideas of this urban interchange ramp bridge,which can be used as a reference for future construction of the same bridge.

Experimental investigation on seismic performance of rigid frame tied-arch bridge with split-piers

A novel seismic design method, namely split-pier seismic design, is proposed. A vertical gap and connect elements are set in split-piers. The lateral stiffness of piers is reduced by cracking of the connect elements under severe earthquake, and the seismic response of bridges is reduced by avoiding the site predominant periods. A model of tied-arch rigid frame bridge with split-piers was designed. Seismic performance was investigated by pseudo-static experimentation on the scale model, The failure process of split-piers, the hysteresis characteristic and the effect of split-piers on the superstructure are presented. Results show that the split-pier has better seismic performance than common ductile piers do.

FREE VIBRATION ANALYSIS OF SHEAR WALLS WITH SHORT PIERS

The equations of the lateral deflection curve of the short pier shear wall under a lateral concentrated load at any level are derived by employing a continuous approach. Lateral flexibility matrixes for the dynamic analysis are also obtained by repeatedly calculating the lateral unit load on the wall at each level where a lumped mass located. Dynamic analyses are implemented for short pier shear walls with different parameters, called the integrative coefficient and the pier strength coefficient related to the dimensions of walls. The influences of two coefficients on the dynamic performances of the structure are studied. Results indicate that with the increase of the integrative coefficient, the periods of top two modes apparently decrease but the other periods of higher frequency modes show little variation when the pier strength coefficient remains constant. Similarly, if the integrative coefficient is constant, the top two periods of the free vibration decrease with the increase of the integrative coefficient but the other periods of higher frequency modes show less variation.

Seismic performance of double- skin steel- concrete composite box piers: Part Ⅰ——Bidirectional quasi-static testing

To study the seismic performance of double-skin steelconcrete composite box（ DSCB） piers, a total of 11 DSCB pier specimens were tested under bidirectional cyclic loading. The effects of the loading pattern, the steel plate thickness, the axial load ratio, the slenderness ratio and the aspect ratio were taken into consideration. The damage evolution process and failure modes of the tested specimens are presented in detail. Test results are also discussed in terms of the hysteretic curve, skeleton curve, ductility and energy dissipation capacity of DSCB pier specimens. It can be concluded that the hysteretic performance of DSCB piers in one direction is affected and weakened by the cyclic loading in the other direction. DSCB piers under bidirectional cyclic loading exhibit good performance in terms of load carrying capacity, ductility, and energy dissipation capacity. Overall, DSCB piers can meet the basic aseismic requirements. The research results can be taken as a reference for using DSCB piers as high piers in bridges in strong earthquakeprone areas.

Seismic performance of double-skin steel-concrete composite box piers: Part Ⅱ—Nonlinear finite element analysis

An accurate finite element （ FE） model was constructed to examine the hysteretic behavior of double-skin steel-concrete composite box （ DSCB） piers for further understanding the seismic performance of DSCB piers; where the local buckling behavior of steel tubes, the confinement of the in-filled concrete and the interface action between steel tube and in-filled concrete were considered. The accuracy of the proposed FE model was verified by the bidirectional cyclic loading test results. Based on the validated FE model, the effects of some key parameters, such as section width to steel thickness ratio, slenderness ratio, aspect ratio and axial load ratio on the hysteretic behavior of DSCB piers were investigated. Finally, the skeleton curve model of DSCB piers was proposed. The numerical simulation results reveal that the peak strength and elastic stiffness decrease with the increase of the section width to steel thickness ratio. Moreover, the increase of the slenderness ratio may result in a significant reduction in the peak strength and elastic stiffness while the ultimate displacement increases. The proposed skeleton curve model can be taken as a reference for seismic performance analyses of the DSCB piers.

Experimental research and finite element analysis of bridge piers failed in flexure-shear modes

In recent earthquakes, a large number of reinforced concrete （RC） bridges were severely damaged due to mixed flexure-shear failure modes of the bridge piers. An integrated experimental and finite element （FE） analysis study is described in this paper to study the seismic performance of the bridge piers that failed in flexure-shear modes. In the first part, a nonlinear cyclic loading test on six RC bridge piers with circular cross sections is carried out experimentally. The damage states, ductility and energy dissipation parameters, stiffness degradation and shear strength of the piers are studied and compared with each other. The experimental results suggest that all the piers exhibit stable flexural response at displacement ductilities up to four before exhibiting brittle shear failure. The ultimate performance of the piers is dominated by shear capacity due to significant shear cracking, and in some cases, rupturing of spiral bars. In the second part, modeling approaches describing the hysteretic behavior of the piers are investigated by using ANSYS software. A set of models with different parameters is selected and evaluated through comparison with experimental results. The influences of the shear retention coefficients between concrete cracks, the Bauschinger effect in longitudinal reinforcement, the bond-slip relationship between the longitudinal reinforcement and the concrete and the concrete failure surface on the simulated hysteretic curves are discussed. Then, a modified analysis model is presented and its accuracy is verified by comparing the simulated results with experimental ones. This research uses models available in commercial FE codes and is intended for researchers and engineers interested in using ANSYS software to predict the hysteretic behavior of reinforced concrete structures.

Rapid repair of severely earthquake-damaged bridge piers with flexural-shear failure mode

An experimental study was conducted to investigate the feasibility of a proposed rapid repair technique for severely earthquake-damaged bridge piers with flexural-shear failure mode. Six circular pier specimens were first tested to severe damage in flexural-shear mode and repaired using early-strength concrete with high-fluidity and carbon fiber reinforced polymers （CFRP）. After about four days, the repaired specimens were tested to failure again. The seismic behavior of the repaired specimens was evaluated and compared to the original specimens. Test results indicate that the proposed repair technique is highly effective. Both shear strength and lateral displacement of the repaired piers increased when compared to the original specimens, and the failure mechanism of the piers shifted from flexural-shear failure to ductile flexural failure. Finally, a simple design model based on the Seible formulation for post-earthquake repair design was compared to the experimental results. It is concluded that the design equation for bridge pier strengthening before an earthquake could be applicable to seismic repairs after an earthquake if the shear strength contribution of the spiral bars in the repaired piers is disregarded and 1.5 times more FRP sheets is provided.

Research on Motion Performance of the Mobile Double-Causeway Pier System

Mobile offshore double-causeway pier system, a type of seashore unloading equipment, consists of two groups of multiple connected semi-submersible modules. This structure has wide application because most of the middle or mini type of vessels and ships can be moored to it. Based on the analysis of computational methods of multi-body motion response, a hydrodynamic model is set up and the three-dimensional potential theory in finite depth is adopted to calculate the three-dimensional motion response of this system. The double P-M spectrum is used to analyze the motion response in irregular waves. Different wave directions are specially taken into consideration, due to their various effects to the motion response. Furthermore, the calculated result is compared with that of the experiment, and it is proved that sway, heave, pitch and yaw motion are greatly constrained by mooring system. The comparison also indicates that the model can forecast the motion performance of the target, and that the calculated result can also be used as reference in connector and mooring system design.

Nonlinear Stability Analysis of Long Span Continuous Rigid Frame Bridge with Thin Wall High Piers

By utilizing the current finite element program ANSYS, two types of finite element models (FEM), the beam model (BM) and shell model (SM), are established for the nonlinear stability analysis of a practical rigid frame bridge—Longtanhe Great Bridge. In these analyses, geometrical and material nonlinearities are simultaneously taken into account. For geometrical nonlinearity, updated Lagrangian formulations are adopted to derive the tangent stiffness matrix. In order to simulate the nonlinear behavior of the plastic hinge of the piers, the multi lines spring element COMBIN39 is used in the SM while the bilinear rotational spring element COMBIN40 is employed in the BM. Numerical calculations show that satisfying results can be obtained in the stability analysis of the bridge when the double coupling nonlinearity effects are considered. In addition, the conclusion is significant for practical engineering.

CFD prediction of local scour hole around bridge piers

In order to predict the local scour hole and its evaluation around a cylindrical bridge pier, the computational fluid dynamics （CFD） and theories of sediment movement and transport were employed to carry out numerical simulations. In the numerical method, the time-averaged Reynolds Navier-Stokes equations and the standard k-e model were first used to simulate the three-dimensional flow field around a bridge pier fixed on river bed. The transient shear stress on river bed was treated as a crucial hydrodynamic mechanism when handling sediment incipience and transport. Then, river-bed volumetric sediment transport was calculated, followed by the modification of the river bed altitude and configuration. Boundary adaptive mesh technique was employed to modify the grid system with changed river-bed boundary. The evolution of local scour around a cylindrical bridge pier was presented. The numerical results represent the flow pattern and mechanism during the pier scouring, with a good prediction of the maximum scour hole depth compared with test results.

Effect of Downward Seepage on Turbulent Flow Characteristics and Bed Morphology around Bridge Piers

In this work, experimental investigations have been pursued to analyse the influence of downward seepage on the turbulent characteristics of flow and corresponding changes in vortex structure around circular bridge pier in alluvial channel. Experiments were conducted in sand bed channel with circular piers of different sizes for no seepage, 10% seepage and 20% seepage cases. The measurement of turbulent flow statistics such as velocity and Reynolds stresses is found to be negative within the scour hole at upstream of the pier whereas application of downward seepage retards the reversal of the flow causing a decrement in the velocity and Reynolds stresses. Higher Reynolds shear stress prevails at the downstream side because of the production of wake vortices. Contribution of all bursting events to the total Reynolds shear stress production has been observed to increase with downward seepage. The analysis of integral scale suggest that size of eddies increases with seepage, which is responsible for increase in particle mobility. Initially rate of scouring is more which abatements gradually with expanding time as well as with the increased of downward seepage. Presence of downward seepage reduces the depth and length of vortex and shifts towards downstream side of the pier.

The design philosophy and bridge＇s technical innovation of Hong Kong- Zhuhai-Macao Bridge

This article introduces the project overview, construction goal and design philosophy of Hong Kong- Zhuhai-Macao Bridge. Based on large scale, factory production, standardization and assemble line, the innova- tive concept is taken as the general principle for design with the emphasis on description of the new material, new technology, new construction method and new equipment used in the design. The application of innovative technology has provided a solid foundation and favorable guarantee for project quality and design service

Experimental study on the width of the turbulent area around bridge pier

At present, the method of calculating the turbulent flow width around the bridge pier is not given in the ＂Standard for Inland River Navigation＂ （GB50139-2004） in China, and the bridge designer usually increases the bridge span in order to ensure the navigation safety, which increases both of the structural design difficulty and the project investments. Therefore, it is extremely essential to give a research on the turbulent flow width around the bridge pier. Through the experiments of the fixed bed and the mobile bed, the factors influencing the turbulent flow width around the bridge pier have been analyzed, such as the approaching flow speed, the water depth, the angles between the bridge pier and the flow direction, the sizes of bridge pier, the shapes of the bridge pier, and the scouting around the bridge pier, etc. Through applying the dimension analytic method to the measured data, the formula of calculating the turbulent flow width around the bridge pier is then inferred.