Superplasticity of fine-grained Mg-10Li alloy prepared by severe plastic deformation and understanding its deformation mechanisms

The superplastic behavior and associated deformation mechanisms of a fine-grained Mg-10.1 Li-0.8Al-0.6Zn alloy(LAZ1011)with a grain size of 3.2μm,primarily composed of the BCCβphase and a small amount of the HCPαphase,were examined in a temperature range of 473 K to 623 K.The microstructural refinement of this alloy was achieved by employing high-ratio differential speed rolling.The best superplasticity was achieved at 523 K and at strain rates of 10^(-4)-5×10^(-4)s^(-1),where tensile elongations of 550±600%were obtained.During the heating and holding stage of the tensile samples prior to tensile loading,a significant increase in grain size was observed at temperatures above 573 K.Therefore,it was important to consider this effect when analyzing and understanding the superplastic deformation behavior and mechanisms.In the investigated strain rate range,the superplastic flow at low strain rates was governed by lattice diffusion-controlled grain boundary sliding,while at high strain rates,lattice diffusion-controlled dislocation climb creep was the rate-controlling deformation mechanism.It was concluded that solute drag creep is unlikely to occur.During the late stages of deformation at 523 K,it was observed that grain boundary sliding led to the agglomeration of theαphase,resulting in significant strain hardening.Deformation mechanism maps were constructed forβ-Mg-Li alloys in the form of 2D and 3D formats as a function of strain rate,stress,temperature,and grain size,using the constitutive equations for various deformation mechanisms derived based on the data of the current tests.

Aging behavior and mechanical properties of 6013 aluminum alloy processed by severe plastic deformation

Structural features, aging behavior, precipitation kinetics and mechanical properties of a 6013 Al–Mg–Si aluminum alloy subjected to equal channel angular pressing （ECAP） at different temperatures were comparatively investigated with that in conventional static aging by quantitative X-ray diffraction （XRD） measurements, differential scanning calorimetry （DSC） and tensile tests. Average grain sizes measured by XRD are in the range of 66-112 nm while the average dislocation density is in the range of 1.20×10^14-1.70×10^14 m^-2 in the deformed alloy. The DSC analysis reveals that the precipitation kinetics in the deformed alloy is much faster as compared with the peak-aged sample due to the smaller grains and higher dislocation density developed after ECAP. Both the yield strength （YS） and ultimate tensile strength （UTS） are dramatically increased in all the ECAP samples as compared with the undeformed counterparts. The maximum strength appears in the samples ECAP treated at room temperature and the maximum YS is about 1.6 times that of the statically peak-aged sample. The very high strength in the ECAP alloy is suggested to be related to the grain size strengthening and dislocation strengthening, as well as the precipitation strengthening contributing from the dynamic precipitation during ECAP.

Crystallization of amorphous NiTi shape memory alloy fabricated by severe plastic deformation

Based on the local canning compression,severe plastic deformation（SPD） is able to lead to the almost complete amorphous nickel-titanium shape memory alloy（NiTi SMA）,in which a small amount of retained nanocrystalline phase is embedded in the amorphous matrix.Crystallization of amorphous NiTi alloy annealed at 573,723 and 873 K was investigated,respectively.The crystallization kinetics of the amorphous NiTi alloy can be mathematically described by the Johnson-MehlAvrami-Kolmogorov（JMAK） equation.NiTi SMA with a complete nanocrystalline phase is obtained in the case of annealing at 573 K and 723 K,where martensite phase transformation is suppressed due to the constraint of the grain boundaries.Crystallization of amorphous NiTi alloy at 873 K leads to the coarse-grained NiTi sample,where（001） martensite compound twin is observed at room temperature.It can be found that the martensitic twins preferentially nucleate at the grain boundary and they grow up towards the two different grains.SPD based on the local canning compression and subsequent annealing provides a new approach to obtain the nanocrystalline NiTi SMA.

Deformation defects and electron irradiation effect in nanostructured Al-Mg alloy processed by severe plastic deformation

In order to explore the exact nature of deformation defects previously observed in nanostructured Al-Mg alloys subjected to severe plastic deformation, a more thorough examination of the radiation effect on the formation of the planar defects in the high pressure torsion （HPT） alloys was conducted using high-resolution transmission electron microscopy （HRTEM）. The results show that high density defects in the HRTEM images disappear completely when these images are exposed under the electron beam for some duration of time. At the same time, lattice defects are never observed within no-defect areas even when the beam-exposure increases to the degree that holes appear in the areas. Therefore, it is confirmed that the planar defects observed in the HPT alloys mainly result from the significant plastic deformation and are not due to the radiation effect during HRTEM observation.

Application of EBSD technique to ultrafine grained and nanostructured materials processed by severe plastic deformation:Sample preparation, parameters optimization and analysis

With the help of FESEM, high resolution electron backscatter diffraction can investigate the grains/subgrains as small as a few tens of nanometers with a good angular resolution （~0.5°）. Fast development of EBSD speed （up to 1100 patterns per second） contributes that the number of published articles related to EBSD has been increasing sharply year by year. This paper reviews the sample preparation, parameters optimization and analysis of EBSD technique, emphasizing on the investigation of ultrafine grained and nanostructured materials processed by severe plastic deformation （SPD）. Detailed and practical parameters of the electropolishing, silica polishing and ion milling have been summarized. It is shown that ion milling is a real universal and promising polishing method for EBSD preparation of almost all materials. There exists a maximum value of indexed points as a function of step size. The optimum step size depends on the magnification and the board resolution/electronic step size. Grains/subgrains and texture, and grain boundary structure are readily obtained by EBSD. Strain and stored energy may be analyzed by EBSD.

Severe plastic deformation (SPD) of biodegradable magnesium alloys and composites: A review of developments and prospects

The use of magnesium in orthopedic and cardiovascular applications has been widely attracted by diminishing the risk of abnormal interaction of the implant with the body tissue and eliminating the second surgery to remove it from the body.Nevertheless,the fast degradation rate and generally inhomogeneous corrosion subsequently caused a decline in the mechanical strength of Mg during the healing period.Numerous researches have been conducted on the influences of various severe plastic deformation(SPD)processes on magnesium bioalloys and biocomposites.This paper strives to summarize the various SPD techniques used to achieve magnesium with an ultrafine-grained(UFG)structure.Moreover,the effects of various severe plastic deformation methods on magnesium microstructure,mechanical properties,and corrosion behavior have been discussed.Overall,this review intends to clarify the different potentials of applying SPD processes to the magnesium alloys and composites to augment their usage in biomedical applications.

Processing and characterization of AZ91 magnesium alloys via a novel severe plastic deformation method:Hydrostatic cyclic extrusion compression(HCEC)

Capability of a novel severe plastic deformation(SPD)method of hydrostatic cyclic extrusion compression(HCEC)for processing of hcp metallic rods with high length to diameter ratios was investigated.The process was conducted in two consecutive cycles on the AZ91 magnesium alloy,and microstructural evolution,mechanical properties and corrosion behavior were investigated.The results showed that the HCEC process was successively capable of producing ultrafine-grained long magnesium rods.Its ability in improving strength and ductility simultaneously was also shown.The ultimate tensile strength and elongation to failure of the sample after the second cycle of the process were improved to be 2.46 and 3.8 times those of the as-cast specimen,respectively.Distribution of the microhardness after the second cycle was uniform and its average value was increased by 116%.The potentials derived from the polarization curves were high and the currents were much low for the processed samples.Also,the diameter of the capacitive arcs derived from the Nyquist curves was large in the HCEC processed samples.The finite element analysis indicated the independency of HCEC load from the length in comparison to the conventional CEC.HCEC is a unique SPD method,which can produce long ultrafine-grained rods with a combination of superior mechanical and corrosion properties.

Strengthening of aluminium alloy 7005 through imposition of severe plastic deformation supplemented by different ageing treatments

Strengthening of aluminium alloys 7xxx through the imposition of severe plastic deformation supplemented by ageing treatments is a challenge due to the limited workability of these alloys in cold deformation regimes.This study aims to comprehensively investigate the strengthening of aluminium alloy 7005 through the imposition of severe plastic deformation supplemented by two different ageing treatments:pre-deformation artificial ageing or postdeformation natural ageing.For this purpose,microstructure evolutions of the alloy processed through mentioned procedures were studied using X-ray diffraction and scanning electron microscopy while the alloy strengthening was evaluated using Vickers hardness measurement.Results show that a superlative strengthening is obtained through the imposition of severe plastic deformation supplemented by post-deformation natural ageing.For instance,the yield strength of the alloy increases to more than 400 MPa,about one-third greater than the counterpart amount after the usual T6 treatment.This superlative strength mainly occurs due to refinement of grains,an increase of dislocation density and an increase of volume fraction of the precipitates that appeared during natural ageing.Considering the applied models,it is inferred that the increase of volume fraction of precipitates that appeared during natural ageing has a determinative role in the strengthening of the alloy.

Structure,strength and superplasticity of ultrafine-grained 1570C aluminum alloy subjected to different thermomechanical processing routes based on severe plastic deformation

A comparative study of the structure and mechanical behavior of an Al-5 Mg-0.18 Mn-0.2 Sc-0.08 Zr-0.01 Fe-0.01 Si(wt.%)alloy ingot subjected to multidirectional isothermal forging(MIF)to a strain of 12 or equal-channel angular pressing(ECAP)to a strain of 10 at 325℃,and subsequent warm and cold rolling(WR and CR)at 325 and 20℃,was performed.The results showed that the MIF process of ultrafine-grained structure with a(sub)grain size dUFG=2μm resulted in enhanced room-temperature ductility and superplastic elongation up to 2800%.Further grain refinement under WR as well as development of a heavily-deformed microstructure with high dislocation density by subsequent CR resulted in a yield/ultimate tensile strength increase from 235/360 MPa after MIF to 315/460 and 400/515 MPa after WR and CR,respectively.Simultaneously,WR led to improved superplastic elongation up to 4000%,while after CR the elongation remained sufficiently high(up to 1500%).Compared with MIF,ECAP resulted in more profound grain refinement(dUFG=1μm),which promoted higher strength and superplastic properties.However,this effect smoothed down upon WR,ensuring equal properties of the processed sheets.CR of the ECAPed alloy,in contrast,led to higher strengthening and slightly better superplastic behavior than those after CR following MIF.

Severe plastic deformation of commercially pure aluminum using novel equal channel angular expansion extrusion with spherical cavity

Equal channel angular expansion extrusion with spherical cavity(ECAEE-SC)was introduced as a novel severe plastic deformation(SPD)technique,which is capable of imposing large plastic strain and intrinsic back-pressure on the processed billet.The plastic deformation behaviors of commercially pure aluminum during ECAEE-SC process were investigated using finite element analysis DEFORM-3D simulation software.The material flow,the load history,the distribution of effective strain and mean stress in the billet were analyzed in comparison with conventional equal channel angular extrusion(ECAE)process.In addition,single-pass ECAEE-SC was experimentally conducted on commercially pure aluminum at room temperature for validation,and the evolution of microstructure and microhardness of as-processed material was discussed.It was shown that during the process,the material is in the ideal hydrostatic stress state and the load requirement for ECAEE-SC is much more than that for ECAE.After a single-pass ECAEE-SC,an average strain of 3.51 was accumulated in the billet with homogeneous distribution.Moreover,the microstructure was significantly refined and composed of equiaxed ultrafine grains with sub-micron size.Considerable improvement in the average microhardness of aluminum was also found,which was homogenized and increased from HV 36.61 to HV 70.20,denoting 91.75%improvement compared with that of the as-cast billet.

SEVERE PLASTIC DEFORMATION TECHNIQUES

There is a considerable interest in developing methods for processing of materials with ultrafine grain si- zes. Widely used methods in refining microstructure are severe/intense plastic deformation techniques, such as torsion straining, equal channel angular (ECA) pressing/extrusion,and accumulative roll bonding (ARB) technique.While the torsion technique has been available for decades,a new torsion system has been developed at DSI for simulation of complex stress states such as combination of shear and compression or shear and tension stress states. The equal channel angular pressing technique is ma- inly used for production of ultrafine grain aluminum alloys,which is aimed at develoment of high strain rate superplasticity.The accumulative roll bonding technique has been applied for the rolling of both aluminum alloy and steels to produce ultrafine gained materials. Three different types of hot compression deformation methods, each with a different number of deforma- tion axis, are introduced in this paper. They are single axis deformation, two axis deformation and three axis deformation.The single axis deformation has us or little restraint such as plane strain type testing and axisymmetric compression testing, the two - axis deformation can be fully restrained or un- restrained, and the three - axis deformation has no restraint. The two - axis restrainsd compression deformation techopue is recommended for loboratory side after comparing the single - axis and the three - axis deformation techniques since the bulk volume of the two - axis restraint compression speci- men can be easily machined into mechanical testing speciments for mechanical property measurement and other studies,and the technique can be aplied to studies of any metallic materials.

Atomistic simulations of the surface severe plastic deformation-induced grain refinement in polycrystalline magnesium:The effect of processing parameters

Magnesium(Mg)based alloys are promising candidates for many applications,but their untreated surfaces usually have low strength and hardness.In this study,a single point diamond turning(SPDT)technique was applied to refine the grain size and improve the mechanical properties of the surface layers of Mg-Li alloys.By refining grains in the topmost layer to the nanometer scale(~60 nm),the surface hardness was found to be enhanced by approximately 60%.The atomic plastic deformation process during the SPDT was then studied by the real-time atomistic molecular dynamics(MD)simulations.A series of MD simulations with different combinations of parameters,including rake angle,cutting speed and cutting depth,were conducted to understand their influences on the microstructural evolution and associated plastic deformation mechanisms on the surface layer of the workpieces.The MD simulation results suggest that using increased rake angle,cutting speed and cutting depth can help to achieve better grain refinement.These simulation results,which provide atomic-level details of the deformation mechanism,can assist the parameter design for the SPDT techniques to achieve the high-performance heterogeneous nanostructured materials.

Impact of severe plastic deformation on kinetics and thermodynamics of hydrogen storage in magnesium and its alloys

Magnesium and its alloys are the most investigated materials for solid-state hydrogen storage in the form of metal hydrides,but there are still unresolved problems with the kinetics and thermodynamics of hydrogenation and dehydrogenation of this group of materials.Severe plastic deformation(SPD)methods,such as equal-channel angular pressing(ECAP),high-pressure torsion(HPT),intensive rolling,and fast forging,have been widely used to enhance the activation,air resistance,and hydrogenation/dehydrogenation kinetics of Mg-based hydrogen storage materials by introducing ultrafine/nanoscale grains and crystal lattice defects.These severely deformed materials,particularly in the presence of alloying additives or second-phase nanoparticles,can show not only fast hydrogen absorption/desorption kinetics but also good cycling stability.It was shown that some materials that are apparently inert to hydrogen can absorb hydrogen after SPD processing.Moreover,the SPD methods were effectively used for hydrogen binding-energy engineering and synthesizing new magnesium alloys with low thermodynamic stability for reversible low/room-temperature hydrogen storage,such as nanoglasses,high-entropy alloys,and metastable phases including the high-pressureγ-MgH2 polymorph.This work reviews recent advances in the development of Mg-based hydrogen storage materials by SPD processing and discusses their potential in future applications.

Mechanical properties and in vivo biodegradability of Mg-Zr-Y-Nd-La magnesium alloy produced by a combined severe plastic deformation

Permanent implants are going to be replaced by the implementation of biodegradable magnesium-based implants in fixation of internal bone fractures because of many concerns associated with conventional implants.However,biodegradable magnesium-based biomaterials exhibit higher biodegradation rate and low mechanical properties which are the main challenges.This work aims to almost overcome both disadvantageous by grain refining of a WE43 magnesium alloy containing 93.04 wt% Mg,4.12 wt% Y,2.15 wt% Nd,0.43 wt% Zr,and 0.26 wt%La.In this study,the consequences of combined severe plastic deformation(SPD) on the mechanical properties,microstructure,and in vivo degradation behavior of WE43 magnesium alloy were investigated.To do so,WE43 magnesium alloy was chosen and processed through multipass equal channel angular pressing(ECAP) at 330℃ for up to four passes followed by an extrusion process.The results showed that higher strength and hardness with minimum ductility less was obtained in the sample processed via two-pass ECAP followed by extrusion.In vivo biodegradation experiments showed higher degradation rate for the unprocessed coarse-grained(CG) WE43 sample.The two-pass ECAP and extruded sample with ultrafine-grained(UFG) structure exhibited the lowest in vivo biodegradation rate besides appropriate mechanical properties.It may be concluded that the WE43 magnesium alloy processed via two-pass ECAP and extrusion could be a very promising candidate for biodegradable implants from both mechanical and biocorrosion viewpoints.

Microstructure tailoring of Al_(0.5)CoCrFeMnNi to achieve high strength and high uniform strain using severe plastic deformation and an annealing treatment

Ultrafine-grained alloys fabricated by severe plastic deformation(SPD)have high strength but often poor uniform ductility.SPD via high-ratio differential speed rolling(HRDSR)followed by an annealing treatment was applied to Al_(0.5)CoCrFeMnNi to design the microstructure from which both high strength and high uniform strain can be achieved.The optimized microstructure was composed of an ultrafine-grained FCC matrix(1.7-2μm)with a high fraction of high-angle grain boundaries(61%-66%)and ultrafine BCC particles(with a size of 0.6-1μm and a volume fraction of8%-9.3%)distributed uniformly at the grain boundaries of the FCC matrix.In the severely plastically deformed microstructure,the nucleation kinetics of the BCC phase was accelerated.Continuous static recrystallization(CSRX)took place during the annealing process at 1273 K.Precipitation of the BCC phase particles occurring concurrently with CSRX effectively retarded the grain growth of the FCC grains.The precipitation of the hard and brittleσphase was,however,suppressed.The annealed sample processed by HRDSR with the optimized microstructure exhibited a high tensile strength of over 1 GPa with a good uniform elongation of 14%-20%.These tensile properties are comparable to those of transformation-induced plasticity steel.Strengthening mechanisms of the severely plastically deformed alloy before and after annealing were identified,and each strengthening mechanism contribution was estimated.The calculated results matched well with the experimental results.

Consolidation of AA 7075-2 wt% ZrO2 Composite Powders by Severe Plastic Deformation via ECAP

The powders of the AA 7075-ZRO2 were mixed by mechanical milling, but it was found that the system presents a few disadvantages when processed by conventional sintering and hot extrusion, since intermetallic phases between ZrO2 particles and alloying elements were formed. Equal channel angular pressing （ECAP） processing was proposed as an alternative method to consolidate the composite where there is no intermetallic formation. The analysis of the ECAP process showed that the intermediate temperature （220℃） produced a higher consolidation level than conventional sintering and hot extrusion （400 and 500℃, respectively）. This fact was supported by relative density analysis. In the case of the sintered and hot-extruded sample, the relative density exhibited a value of 0.95, while ECAP sample showed a value of 0.98. Hardness values show that microstructural refinement obtained during mechanical milling was preserved during ECAP processing even when it was carded out at 220℃.

Grain refinement in low SFE and particle-containing nickel aluminium bronze during severe plastic deformation at elevated temperatures

The influence of particle size and morphology on grain refinement in low stacking fault energy(SFE)alloys was studied by comparing the grain structures in single-and multi-phase Al-bronze(AB)alloys following equal channel angular pressing(ECAP)between 350 and 500℃.In particular,nickel aluminium bronze(NAB)was chosen as it contained both coarse and fine rounded particles,as well as a lamellar phase which evolved during ECAP.Grain refinement in the single-phase alloy was achieved through dynamic recrystallisation initiated at deformed twin boundaries.By contrast,different mechanisms were observed in the particle-containing NAB.Recrystallisation around the coarseκⅡparticles(~5μm)was promoted through particle stimulated nucleation(PSN),whereas recrystallisation in the region of the fineκⅣ(~0.4μm)was delayed due to the activation of secondary slip.Grain refinement in areas of the lamellarκⅢshowed significant variation,depending on the lamellar orientation relative to the shear plane of ECAP.As the lamellae deformed,numerous high angle grain boundaries were generated between fragments and served as nucleation sites for recrystallisation,while PSN occurred around spheroidised lamellae.The spreading of theκⅢparticles by ECAP then enhanced the total area of recrystallised grains.

Evolution of Quasicrystals and Long-Period Stacking Ordered Structures During Severe Plastic Deformation and Mixing of Dissimilar Mg Alloys Upon Friction Stir Welding

Microstructural evolution during severe plastic deformation and mixing of Mg95.8Zn3.6Gd0.6 and Mg97Cu1Y2(at%)alloys upon friction stir welding was studied.A laminated onion-ring structure composed of alternative distribution of layers with signifi cantly refi ned microstructures from diff erent alloys was formed in the stirred zone.Coarse quasicrystals were broken up and dispersed with most of them being transformed into cubic W-phase particles,and thick 18R long-period stacking ordered plates were fractured and transformed into fi ne 14H-LPSO lamellae in the stirred zone(SZ)experiencing complex material flow under high strain rate.Fine W-phase particles and 14H-LPSO lamellae formed during dissimilar friction stir welding(FSW)usually have no specifi c orientation relationship with surrounding Mg matrix.Chemical measurements demonstrated occurrence of interdiff usion between dissimilar layers in the SZ.Phase transformation was observed for some particles of quasicrystals and long-period stacking ordered(LPSO)in regions slightly outside the SZ.An ultimate tensile strength of~415 MPa and an elongation to failure of~27.8%,both exceeding those of base materials,were obtained in the SZ,due to microstructural refi nement and formation of a laminated structure.

Corrosion behavior of severely plastically deformed Mg and Mg alloys

Magnesium(Mg)alloys have several advantages,such as low density,high specific strength and biocompatibility.However,they also suffer weak points,such as high corrosion,low formability and easy ignition,which makes their applications limited.Many studies have been conducted to overcome these disadvantages and further improve the advantages of Mg alloys.Severe plastic deformation(SPD)is one of the most important techniques and has great effects on the microstructure refinement of Mg alloys and improvements in their strength and formability.Several researchers have studied the corrosion behavior of SPD-processed Mg alloys in recent decades.However,these studies have reported some controversial effects of SPD on the corrosion of Mg alloys,which makes the research roadmap ambiguous.Therefore,it is important to review the literature related to the corrosion properties of Mg alloys prepared by SPD and understand the mechanisms controlling their corrosion behavior.Effective grain refinement by SPD improves the corrosion properties of pure Mg and Mg alloys,but control of the processing conditions is a key factor for achieving this goal because texture,dislocation density,size and morphology of secondary phase also importantly affects the corrosion properties of Mg alloys.Reduced grain size in the fine grain-size range can decrease the corrosion rate due to the increased barrier effect of grain boundaries against corrosion and the formation of a stable passivation layer on the surface of fine grains.Basal texture reduces the corrosion rate because basal planes with the highest atomic planar density are more corrosion resistant than other planes.Increased dislocation density after SPD deteriorates the corrosion resistance of the interior grains and thus proper annealing after SPD is important.The fine and uniform distribution of secondary phase particles during SPD is important to minimize the micro-galvanic corrosion effect and retain small grains during annealing treatment for removing dislocations.

Microstructural Evolution of Plastic Deformation of NiTi Shape Memory Alloy at Low Temperature

Nickel-titanium shape memory alloy （NiTi SMA） which possesses crystal structure of B2 austenite at room temperature was subjected to plastic deformation at low temperature （-150 ℃） by means of local canning compression. The microstructural evolution of NiTi SMA at the different deformation degree was investigated by transmission electron microscopy （TEM） and high resolution transmission electron microscopy （HRTEM）. At the deformation degree by 15%, a high density of dislocations occurs in the deformed NiTi sample. At the deformation degree by 25%, the deformed NiTi sample exhibits the martensite morphology due to the pinning of dislocations at the grain boundaries. At the deformation degree by 50%, a small amount of nanocrystalline phase arises in the deformed NiTi sample. At the deformation degree by 80%, severe plastic deformation （SPD） leads to the occurrence of a great deal of amorphous and nanocrystalline phase,