A strategy for strengthening chaotic mixing of dual shaft eccentric mixers by changing non-Newtonian fluids kinetic energy distribution

Efficiently modulating the velocity distribution and flow pattern of non-Newtonian fluids is a critical challenge in the context of dual shaft eccentric mixers for process intensification,posing a significant barrier for the existing technologies.Accordingly,this work reports a convenient strategy that changes the kinetic energy to controllably regulate the flow patterns from radial flow to axial flow.Results showed that the desired velocity distribution and flow patterns could be effectively obtained by varying the number and structure of baffles to change kinetic energy,and a more uniform velocity distribution,which could not be reached normally in standard baffle dual shaft mixers,was easily obtained.Furthermore,a comparative analysis of velocity and shear rate distributions is employed to elucidate the mechanism behind the generation of flow patterns in various dual-shaft eccentric mixers.Importantly,there is little difference in the power number of the laminar flow at the same Reynolds number,meaning that the baffle type has no effect on the power consumption,while the power number of both unbaffle and U-shaped baffle mixing systems decreases compared with the standard baffle mixing system in the transition flow.Finally,at the same rotational condition,the dimensionless mixing time of the U-shaped baffle mixing system is 15.3%and 7.9%shorter than that of the standard baffle and the unbaffle mixing system,respectively,which shows the advantage of the U-shaped baffle in stirring rate.

A Multiscale Reliability-Based Design Optimization Method for Carbon-Fiber-Reinforced Composite Drive Shafts

Carbon fiber composites,characterized by their high specific strength and low weight,are becoming increasingly crucial in automotive lightweighting.However,current research primarily emphasizes layer count and orientation,often neglecting the potential of microstructural design,constraints in the layup process,and performance reliability.This study,therefore,introduces a multiscale reliability-based design optimization method for carbon fiber-reinforced plastic(CFRP)drive shafts.Initially,parametric modeling of the microscale cell was performed,and its elastic performance parameters were predicted using two homogenization methods,examining the impact of fluctuations in microscale cell parameters on composite material performance.A finite element model of the CFRP drive shaft was then constructed,achieving parameter transfer between microscale and macroscale through Python programming.This enabled an investigation into the influence of both micro and macro design parameters on the CFRP drive shaft’s performance.The Multi-Objective Particle Swarm Optimization(MOPSO)algorithm was enhanced for particle generation and updating strategies,facilitating the resolution of multi-objective reliability optimization problems,including composite material layup process constraints.Case studies demonstrated that this approach leads to over 30%weight reduction in CFRP drive shafts compared to metallic counterparts while satisfying reliability requirements and offering insights for the lightweight design of other vehicle components.

Beyond p-y method:A review of artificial intelligence approaches for predicting lateral capacity of drilled shafts in clayey soils

In 2023,pivotal advancements in artificial intelligence(AI)have significantly experienced.With that in mind,traditional methodologies,notably the p-y approach,have struggled to accurately model the complex,nonlinear soil-structure interactions of laterally loaded large-diameter drilled shafts.This study undertakes a rigorous evaluation of machine learning(ML)and deep learning(DL)techniques,offering a comprehensive review of their application in addressing this geotechnical challenge.A thorough review and comparative analysis have been carried out to investigate various AI models such as artificial neural networks(ANNs),relevance vector machines(RVMs),and least squares support vector machines(LSSVMs).It was found that despite ML approaches outperforming classic methods in predicting the lateral behavior of piles,their‘black box'nature and reliance only on a data-driven approach made their results showcase statistical robustness rather than clear geotechnical insights,a fact underscored by the mathematical equations derived from these studies.Furthermore,the research identified a gap in the availability of drilled shaft datasets,limiting the extendibility of current findings to large-diameter piles.An extensive dataset,compiled from a series of lateral loading tests on free-head drilled shaft with varying properties and geometries,was introduced to bridge this gap.The paper concluded with a direction for future research,proposes the integration of physics-informed neural networks(PINNs),combining data-driven models with fundamental geotechnical principles to improve both the interpretability and predictive accuracy of AI applications in geotechnical engineering,marking a novel contribution to the field.

Clinical effect of operative vs nonoperative treatment on humeral shaft fractures:Systematic review and meta-analysis of clinical trials

BACKGROUND Whether operation is superior to non-operation for humeral shaft fracture remains debatable.We hypothesized that operation could decrease the nonunion and reintervention rates and increase the functional outcomes.AIM To compare the clinical efficacy between operative and nonoperative approaches for humeral shaft fractures.METHODS We searched the PubMed,Web of Science,ScienceDirect,and Cochrane databases from 1990 to December 2023 for clinical trials and cohort studies comparing the effects of operative and conservative methods on humeral shaft fractures.Two investigators independently extracted data from the eligible studies,and the other two assessed the methodological quality of each study.The quality of the included studies was assessed using the Cochrane risk bias or Newcastle-Ottawa Scale.The nonunion,reintervention and the overall complications and functional scores were pooled and analyzed using Review Manager software(version 5.3).RESULTS A total of four randomized control trials and 13 cohort studies were included,with 1285 and 1346 patients in the operative and nonoperative groups,respectively.Patients in the operative group were treated with a plate or nail,whereas those in the conservative group were managed with splint or functional bracing.Four studies were assessed as having a high risk of bias,and the other 13 were of a low risk of bias according to the Newcastle-Ottawa Scale or Cochrane risk bias tool.The operative group had a significantly decreased rate of nonunion[odds ratio(OR)0.30;95%CI:0.23 to 0.40,reintervention(OR:0.33;95%CI:0.24 to 0.47),and overall complications(OR:0.62;95%CI:0.49 to 0.78)].The pooled effect of the Disabilities of Arm,Shoulder,and Hand score showed a significant difference at 3[mean difference(MD)-8.26;95%CI:-13.60 to-2.92],6(MD:-6.72;95%CI:-11.34 to-2.10),and 12 months(MD:-2.55;95%CI:-4.36 to-0.74).The pooled effect of Visual Analog Scale scores and the Constant-Murley score did not significantly differ between the two groups.CONCLUSION This systematic review and meta-analysis revealed a trend of rapid functional recovery and decreased rates of nonunion and reintervention after operation for humeral shaft fracture compared to conservative treatment.

Early Treatment Outcome of Humeral Shaft Fracture Non-Union in Adults: Comparative Study of Plating versus Interlocking Nailing

Background: Fractures of humeral shaft in adults are common injuries. Humeral shafts non-union either from late presentation after initial treatment by traditional bone setters or failed non-operative orthodox care is a major problem in this part of the world. This non-union is a major treatment challenge with increased cost of care and morbidity in this part of the world. Humeral shaft non-union can be treated with locked intra-medullary nailing (LIMN) or dynamic compression plating (DCP). Study on comparison of these methods of fixation in this part of the world is scarce in literature search, hence the reason for this study. Objective: The objectives of this study are: (1) to compare early clinical outcome following fixation of humeral shaft fracture nonunion with DCP versus LIMN;(2) to compare the time of radiologic fracture union of DCP with LIMN;(3) to compare complications following fixation of humeral shaft fracture nonunion with DCP versus LIMN. Patients and Methods: This was a randomized control study done for 2 years in which fifty adult patients with humeral shaft non-union were recruited. The patients were grouped into 2 (P = DCP & N = LIMN). Forty five of the patients completed the follow up periods of the study and then analyzed. The P group had ORIF with DCP while the N group had ORIF with LIMN. Both groups had grafting with cancellous bones. Each patient was followed up for a period of 6 months at the time which radiographic union is expected. Any patient without clinical and/or radiographic evidence of union after six months of surgery was diagnosed as having recurrent non-union. The data generated was analyzed using SPSS Version 23. The results were presented in charts and tables. The paired t-test was used while considering p value Result: Forty five patients completed follow up. There was a male preponderance (4:1), right humerus predominated (3:2). Motor vehicular accidents were the commonest cause of the fractures (62%). Most non-union fractures occurred at the level of the middle 3rd of the humeral shaft (60%). Failed TBS treatment was the commonest indication for the osteosynthesis (71%). More patients had plating (53%) compared to 47% who had LIMN. Most patients (93.4%) had union between 3 to 6 months irrespective of fixation type with no significant statistical difference between the union rate of DCP and LIMN (p value 0.06) with similar functional outcome and complication rates irrespective of the type of fixation. Conclusion: This study showed that the success rates in term of fracture union, outcome functional grades and complication rates were not directly dependent on the types of the fixation: plating or locked intra-medullary nailing.

Functional Outcomes of Adult Tibia Shaft Fractures Treated with Solid Intramedullary Nails versus Hollow Nails: A Systematic Review

Introduction: The management of fractures of the tibia shaft is an important aspect of orthopaedic care, and the selection of the surgical method for fixation can substantially impact patient outcomes. The current review aims to compare the outcomes of adult tibia fractures treated with solid nails to those treated with hollow nails. Methods: A search on Scopus, PubMed, and Cochrane Library, using three keywords (Outcome, Tibia shaft fractures, Nail) was conducted in April 2023. Results were compiled and two independent reviewers screened and selected eligible articles After removing duplicates, titles and abstracts were read to exclude ineligible studies. Full-text articles of the remaining papers were read to select eligible studies which were further critically appraised to ascertain their methodological quality. The data extracted from the selected papers were synthesized using a combination of pooling of results, tests of statistical difference (t-test and chi-square) and narrative synthesis methods. Results: A total of 2295 articles were obtained from the databases and citation searching. A total of 9 papers were identified as eligible and included in the review. Findings revealed that there is no statistical difference in the outcomes of tibia fractures treated with either solid or hollow nail groups such as duration of surgery (p = 0.541), rate of delayed and non-union (p = 0.342), and rate of surgical site infections (p = 0.395). Conclusion: Intramedullary nailing of tibia shaft fractures with either solid or hollow nails have similar functional outcomes.

Short-term warning and integrity monitoring algorithm for coal mine shaft safety

A new short-term warning and integrity monitoring algorithm was proposed for coal mine shaft safety. The Kalman filter (KF) model was used to extract real global positioning system (GPS) kinematic deformation information. The short-term warning model was built by using the two-side cumulative sum (CUSUM) test, which further improves the warning system reliability. Availability (the minimum warning deformation, MWD), false alarm rate (the average run length, ARL), missed rate (the warning delay, WD) and the relationships among them were analyzed and the method choosing warning parameters is given. A test of a deformation simulation platform shows that the warning algorithm can be effectively used for steep deformation warning. A field experiment of the Malan mine shaft in Shanxi coal area illustrates that the proposed algorithm can detect small dynamic changes and the corresponding occurring time. At given warning thresholds (MWD is 15 mm and ARL is 1000),the detected deformations of two consecutive days’ deformation sequences with the algorithm occur at the 705th epoch (705 s) and the 517th epoch (517 s), respectively.

Smoke distribution in naturally ventilated urban transportation tunnels with multiple shafts

The smoke spreading law of urban transportation tunnels with multiple shafts under natural ventilation is studied.A full-scale burning experiment is conducted in an actual tunnel.The study shows that smoke temperatures below the tunnel ceiling reduce rapidly along the longitudinal towards the tunnel exits. A noticeable temperature stratification is observed near the fire source.Most fire smoke is exhausted out of the shafts while the number of the smoke shafts in the downstream is more than that in the upstream.Large eddy simulation LES based on computational fluid dynamics CFD is carried out using the fire dynamics simulator FDS software with parallel processing in which the grid size of the fire-domain is set to be 0.083 m.The simulation results of temperatures under the ceiling the smoke fronts and the shafts＇smoke exhaust or air supply agree reasonably with the experimental data. Further simulations indicate that the decreasing ambient temperature or shaft spacing might reduce smoke temperatures under the tunnel ceiling and increase mass flow rates out of the shafts.This study provides technical scientific evidence and supports for the design and construction of such kinds of tunnels.

NUMERICAL ANALYSIS ON INCREASE OF SECTIONAL STRESS OF A SHAFT WITH RUB－IMPACT CONDITION

The numerical analysis on a shaft with rub-impact condition is done by using the finite difference method. The bending modes and the moment yaring along the shaft are described,to reveal the in crease pattern of sectional stress of the shaft. The result obtained in this paper can be used in explaining the phenomena of many breaking sections appeared in destructive failures of actual rotating machinery.

Study of LDBPs Shaft Skin Friction for Piles in Cohesiove Soils

The methodology of predicting pile shaft skin ultimate friction has been studied in a systematic way. In the light of that, the analysis of the pile shaft resistance for bored and cast in situ piles in cohesive soils was carried out thoroughly in the basis of field performance data of 10 fully instrumented large diameter bored piles (LDBPs) used as the bridge foundation. The undrained strength index μ in term of cohesive soils was brought forward in allusion to the cohesive soils in the consistence plastic state, and can effectively combine the friction angle and the cohesion of cohesive soils in undrained condition. And that the classical ' α method' was modified much in effect to predict the pile shaft skin friction of LDBPs in cohesive soils. Furthermore, the approach of standard penetration test (SPT) N value used to estimate the pile shaft skin ultimate friction was analyzed, and the calculating formulae were established for LDBPs in clay and silt clay respectively.

Simulation Study on Reinforcing Overburden to Prevent and Cure the Rupture of Shaft Lining

For preventing and curing the rupture disaster of shaft lining effectively, according to the additional force theory of shaft lining fracture, more than forty tests were carried out on the large scale test rig on the basis of simulating theory. The influence of the position of aquifer, the reinforcing scope of aquifer, reinforcing distance and the strength of grouting cemented mixture on the value and variation law of the axial additional force on shaft lining is studied. The relationships between the reinforcing parameters and the axial additional force on shaft lining are obtained, which provides the theoretic foundation and construction design parameters for the method of reinforcing strata by grouting to prevent and cure tbe rupture disaster of shart lining.

Effects of Flexibility and Suspension Configuration of Main Shaft on Dynamic Characteristics of Wind Turbine Drivetrain

The current research of wind turbine drivetrain is mainly concentrated in dynamic characteristics of gearbox with a specific suspension of main shaft, such as one-point and two-point suspension. However, little attention is paid to the e ects of these suspension configurations on the dynamic responses of wind turbine gearbox. This paper investigates the influences of suspension configurations of main shaft on the dynamic characteristics of drivetrain. For evaluating the dynamic behaviors of drivetrain with multi-stage transmission system more realistically, a dynamic modeling approach of drivetrain is proposed based on Timoshenko beam theory and Lagrange's equation. Considering the flexibility and di erent suspension configurations of main shaft, time-varying mesh sti ness excitation, time-varying transmission error excitation and gravity excitation, etc., a three-dimensional dynamic model of drivetrain is developed, and the dynamic responses of drivetrain are investigated. Results show that with the one-point suspension of main shaft, the resonance frequencies in gearbox, especially at the low-speed stage, obviously shift to the higher frequency range compared to the gearbox without main shaft, but this trend could be inversed by increasing main shaft length. Meanwhile, the loads in main shaft, main shaft bearing and carrier bearing are greatly sensitive to the main shaft length. Hence, the load sharing is further disrupted by main shaft, but this e ect could be alleviated by larger load torque. Comparing to the one-point suspension of main shaft, there occurs the obvious load reduction at the low-speed stage with two-point suspension of main shaft. However, those advantages greatly depend on the distance between two main bearings, and come at the expense of increased load in upwind main shaft unit and the corresponding main bearing. Finally, a wind field test is conducted to verify the proposed drivetrain model. This study develops a numerical model of drivetrain which is able to evaluate the e ects of di erent suspension configurations of main shaft on gearbox.

Lightweight Design of Automobile Drive Shaft Based on the Characteristics of Low Amplitude Load Strengthening

There are two kinds of internationally recognized approaches in terms of lightweight design.One is based on fatigue accumulated damage theory to achieve better reliability by optimal structural design; another is to use high performance lightweight materials.The former method takes very few considerations on the structural strengthening effects caused by the massive small loads in service.In order to ensure safety,the design is usually conservative,but the strength potential of the component is not fully exerted.In the latter method,cost is the biggest obstacle to lightweight materials in automotive applications.For the purpose of light weighting design on a fuel cell vehicle,the new design method is applied on drive shafts.The method is based on the low amplitude load strengthening characteristics of the material,and allows the stress,corresponding to test load,to enter into the strengthened range of the material.Under this condition,the light weighting design should assure that the reliability of the shaft is not impaired,even maximizes the strength potential of machine part in order to achieve the weight reduction and eventually to reduce the cost.At last,the feasibility of the design is verified by means of strength analysis and modal analysis based on the CAD model of light weighted shaft.The design applies to the load case of half shaft in independent axle,also provides technological reference for the structural lightweight design of vehicles and other machineries.

Quick determination of gas pressure before uncovering coal in cross-cuts and shafts

The determination of gas pressure before uncovering coal in cross-cuts and in shafts is one of the important steps in pre- dicting coal and gas outbursts. However, the time spent for testing gas pressure is, at present, very long, seriously affecting the ap- plication of outburst prediction techniques in opening coal seams in cross-cuts and shafts. In order to reduce the time needed in gas pressure tests and to improve the accuracy of tests, we analyzed the process of gas pressure tests and examined the effect of the length of boreholes in coal seams in tests. The result shows that 1) the shorter the borehole, the easier the real pressure value of gas can be obtained and 2) the main factors affecting the time spent in gas pressure tests are the length of the borehole in coal seams, the gas emission time after the borehole has been formed and the quality of the borehole-sealing. The longer the length of the bore- hole, the longer the gas emission time and the larger the pressure-relief circle formed around the borehole, the longer the time needed for pressure tests. By controlling the length of the borehole in a test case in the Huainan mining area, and adopting a quick sealing technique using a sticky liquid method, the sealing quality was clearly improved and the gas emission time as well as the amount of gas discharged greatly decreased. Before the method described, the time required for the gas pressure to increase during the pressure test process, was more than 10 days. With our new method the required time is only 5 hours. In addition, the accuracy of the gas pressure test is greatly improved.

Direct reduction swelling behavior of pellets in hydrogen-based shaft furnaces under typical atmospheres

Hydrogen-based shaft furnace process is gaining more and more attention due to its low carbon emission, and the reduction behavior of iron bearing burdens significantly affects its operation. In this work, the effects of reduction degree, temperature, and atmosphere on the swelling behavior of pellet has been studied thoroughly under typical hydrogen metallurgy conditions. The results show that the pellets swelled rapidly in the early reduction stage, then reached a maximum reduction swelling index (RSI) at approximately 40%reduction degree. The crystalline transformation of the iron oxides during the reduction process was the main reason of pellets swelling. The RSI increased significantly with increasing temperature in the range of 850-1050℃, the maximum RSI increased from 6.66%to 25.0%in the gas composition of 100%H_(2). With the temperature increased, the pellets suffered more thermal stress resulting in an increase of the volume. The maximum RSI decreased from 19.78%to 17.35%with the volume proportion of H_(2) in the atmosphere increased from 55%to 100%at the temperature of 950℃.The metallic iron tended to precipitate in a lamellar structure rather than whiskers. Consequently, the inside of the pellets became regular, so the RSI decreased. Overall, controlling a reasonable temperature and increasing the H_(2) proportion is an effective way to decrease the RSI of pellets.

Research on Stress and Strength of High Strength Reinforced Concrete Drilling Shaft Lining in Thick Top Soils

High strength reinforced concrete drilling shaft linings have been adopted to solve the difficult problem of supporting coal drilling shafts penetrating through thick top soils. Through model experiments the stress and strength of such shaft linings are studied. The test results indicate that the load beating capacity of the shaft lining is very high and that the main factors affecting the load bearing capacity are the concrete strength, the ratio of lining thickness to inner radius and the reinforcement ratio. Based on the limit equilibrium conditions and the strength theory of concrete under multi-axial compressive stressed state, a formula for calculating the load-beating capacity of a high strength reinforced concrete shaft lining was obtained. Because the concrete in a shaft lining is in a multi-axial compressive stress state the compressive strength increases to a great extent compared to uni-axial loading. Based on experiment a formula for the gain factor in compressive strength was obtained： it can be used in the structural design of the shaft lining. These results have provided a basis for sound engineering practice when designing this kind of shaft lining structure.

Empirical methods for determining shaft bearing capacity of semi-deep foundations socketed in rocks

Semi-deep foundations socketed in rocks are considered to be a viable option for the foundations in the presence of heavy load imposed by high-rise structures, due to the low settlement and high bearing capacity. In the optimum design of semi-deep foundations, prediction of the shaft bearing capacity, rs, of foundations socketed in rocks is thus critically important. In this study, the unconfined compressive strength(UCS), qu, has been applied in order to investigate the shaft bearing capacity. For this, a database of 106 full-scale load tests is compiled with UCS values of surrounding rocks, in which 34 tests with rock quality designation(RQD), and 5 tests with rock mass rating(RMR). The bearing rocks for semi-deep foundations include limestone, mudstone, siltstone, shale, granite, tuff, granodiorite, claystone, sandstone, phyllite, schist, and greywacke. Using the database, the applicability and accuracy of the existing empirical methods are evaluated and new relations are derived between the shaft bearing capacity and UCS based on the types of rocks. Moreover, a general equation in case of unknown rock types is proposed and it is verified by another set of data. Since rock-socketed shafts are supported by rock mass(not intact rock), a reduction factor for the compressive strength is suggested and verified in which the effect of discontinuities is considered using the modified UCS, qu(modified), based upon RMR and RQD in order to take into account the effect of the rock mass properties.

Cutting parameter optimization for one-step shaft excavation technique based on parallel cutting method

The outcome of the cutting blasting in a one-step shaft excavation is heavily related to the cutting parameters used for parallel cutting method. In this study, the relationships between the cutting parameters（such as the hole spacing L and the empty hole diameter D） and damage zones were investigated by numerical simulation. A damage state index γ was introduced and used to characterize the crushing and crack damage zones through a user-defined subroutine. Two indices, i.e., η1 and η2 that can reflect the cutting performance, were also introduced. The simulation results indicate that an optimal value of L can be obtained so that the η1 and η2 can reach their optimal states for the best cutting performance. A larger D results in better cutting performance when the L value maintains its best. In addition, the influences of the loading rate and the in-situ stress on the cutting performance were investigated. It is found that an explosive with a high loading rate is suit for cutting blasting. The propagation direction and the length of the tensile cracks are affected by the direction and the magnitude of the maximum principal stress.

Deformation Analysis and Stability Evaluation of the Main Shaft at Jinchuan Mine No.3

Unexpected, serious deformation failures have occurred during construction of a main shaft. A study of construction parameters of the main shaft is required. First, the stability of the shaft and wall-rock is investigated by numerical methods. The modeling results are as follows： The convergence of shaft liner is greater than 60 mm at a depth of 650 m; the maximum principal stress in the liner approaches 190 MPa, which exceeds the strength of the liner, so it is inevitable that the liner deform locally. Second, stability analysis of shafts with different liner thicknesses has been completed. The results have the following features： If the depth where the liner thickness is increases from 400 mm to 500 mm is 650 meters, the convergence deformation of the liner is reduced by 3.4 mm while the maximum principal stress is reduced by 5 MPa. At a depth of 250 m if the liner thickness is increased from 400 mm to 500 mm the convergence of the liner is reduced by 1.5 mm while the maximum principal stress is reduced by 10 MPa. Therefore, increasing the liner thickness has little effect on liner convergence but can reduce the maximum principal stress in the liner. The thickness of the liner can be increased to reduce the maximum principal stress and increase the capacity for shear deformation. Finally, construction techniques employing releasing-displacements have been numerically simulated. The conclusions are that as the releasing displacement is increased the convergence of the surrounding rock increases linearly while the convergence of the lining decreases linearly. The plastic zone in the surrounding rock mass at first increases linearly but then, at a release-displacement of 95 ram, expands rapidly. These conclusions show that use of suitable releasing displacement can increase the self-supporting capacity of the surrounding rock. But when the releasing displacement exceeds 95 nun the plastic zone rapidly enlarges and stability rapidly decreases. The maximum principal stress of the lining also decreases as the release-displacement increases. There is a definite inflection point in the relationships involving releasing displacement. When the releasing displacement passes this point the effect on principal stress decreases. In conclusion, a reasonable releasing displacement value when lining the shaft is 95 mm.

A laser shaft alignment system with dual PSDs

Shaft alignment is an important technique during installation and maintenance of a rotating machine. A high-precision laser alignment system has been designed with dual PSDs (Position Sensing Detector) to change traditional manual way of shaft alignment and to make the measurement easier and more accurate. The system is comprised of two small measuring units (laser transmitter and detector) and a PDA (Personal Digital Assistant) with measurement software. The laser alignment system with dual PSDs was improved on a single PSD system, and yields higher measurement accuracy than the previous design, and has been successful for designing and implements actual shaft alignment. In the system, the range of offset measurement is ±4 mm, and the resolution is 1.5 μm, with accuracy being less than 2 μm.