The craft of auxiliary dobby shaft is one of methods used in the traditional figured woven textiles and especially brocade in China.Based on the principle of auxiliary dobby shaft,a new method of weave design was prop...The craft of auxiliary dobby shaft is one of methods used in the traditional figured woven textiles and especially brocade in China.Based on the principle of auxiliary dobby shaft,a new method of weave design was proposed.The relevant arrangement of warp and weave design were discussed.It is shown that this method can be applied on one electronic jacquard loom with single warp beam for new product development and production.And this effect will open up a new way to reproduce traditional fabrics in order to protect and develop Chinese traditional culture.展开更多
There are two kinds of internationally recognized approaches in terms of lightweight design.One is based on fatigue accumulated damage theory to achieve better reliability by optimal structural design; another is to u...There are two kinds of internationally recognized approaches in terms of lightweight design.One is based on fatigue accumulated damage theory to achieve better reliability by optimal structural design; another is to use high performance lightweight materials.The former method takes very few considerations on the structural strengthening effects caused by the massive small loads in service.In order to ensure safety,the design is usually conservative,but the strength potential of the component is not fully exerted.In the latter method,cost is the biggest obstacle to lightweight materials in automotive applications.For the purpose of light weighting design on a fuel cell vehicle,the new design method is applied on drive shafts.The method is based on the low amplitude load strengthening characteristics of the material,and allows the stress,corresponding to test load,to enter into the strengthened range of the material.Under this condition,the light weighting design should assure that the reliability of the shaft is not impaired,even maximizes the strength potential of machine part in order to achieve the weight reduction and eventually to reduce the cost.At last,the feasibility of the design is verified by means of strength analysis and modal analysis based on the CAD model of light weighted shaft.The design applies to the load case of half shaft in independent axle,also provides technological reference for the structural lightweight design of vehicles and other machineries.展开更多
With regard to function, the strengths for interference articulation of a roller shaft formed a series system. As the three strength reliabilities conditioned each other, there was a problem for the system reliability...With regard to function, the strengths for interference articulation of a roller shaft formed a series system. As the three strength reliabilities conditioned each other, there was a problem for the system reliability to apportion rationally. In fact, there was a transition from safety to deactivation. The state of structure was fuzziness which was in both safety and non-safety states. Therefore the reliability was a fuzzy event which considered the randomness for some design parameters and the fuzziness for the thresholds between generalized strength safety and deactivation. The mathematical model of fuzzy reliability design for the interference articulation of the roller shaft was presented. Eight design examples were calculated.展开更多
In the paper the three-dimensional flow fields are numerically simulated in the vertical-shaft mechanical mix tank of a water treatment plant by means of FLUENT software based on the method of Computational Fluid Dyna...In the paper the three-dimensional flow fields are numerically simulated in the vertical-shaft mechanical mix tank of a water treatment plant by means of FLUENT software based on the method of Computational Fluid Dynamics (CFD). The influences of design parameters on flow fields and the mixing effect are analyzed. Firstly,the prediction capability of the turbulence model adopted in simulations is evaluated. And then,the mesh independence is checked up. Finally,the flow fields in various dimensionless blade diameters and dimensionless shaft spans are numerically simulated respectively. The results have shown that the numerical simulation method based on CFD is a feasible assistance for the optimal designs of mixers. Moreover,the optimal design of the blade diameter should take into account both the flow field and the power consumption. The optimization of the shaft span is to achieve a relatively even distribution of the flow field without any rupture. With the consideration of an optimal design,the dimensionless blade diameter and dimensionless shaft span should be 0.45 and 0.57 respectively in the case.展开更多
文摘The craft of auxiliary dobby shaft is one of methods used in the traditional figured woven textiles and especially brocade in China.Based on the principle of auxiliary dobby shaft,a new method of weave design was proposed.The relevant arrangement of warp and weave design were discussed.It is shown that this method can be applied on one electronic jacquard loom with single warp beam for new product development and production.And this effect will open up a new way to reproduce traditional fabrics in order to protect and develop Chinese traditional culture.
基金supported by National Natural Science Foundation of China (Grant No. 50875173)Shanghai Municipal Education Commission Key Foundation of China (Grant No. 09ZZ157)Shanghai Leading Academic Discipline Project of China (Grant No. J50503)
文摘There are two kinds of internationally recognized approaches in terms of lightweight design.One is based on fatigue accumulated damage theory to achieve better reliability by optimal structural design; another is to use high performance lightweight materials.The former method takes very few considerations on the structural strengthening effects caused by the massive small loads in service.In order to ensure safety,the design is usually conservative,but the strength potential of the component is not fully exerted.In the latter method,cost is the biggest obstacle to lightweight materials in automotive applications.For the purpose of light weighting design on a fuel cell vehicle,the new design method is applied on drive shafts.The method is based on the low amplitude load strengthening characteristics of the material,and allows the stress,corresponding to test load,to enter into the strengthened range of the material.Under this condition,the light weighting design should assure that the reliability of the shaft is not impaired,even maximizes the strength potential of machine part in order to achieve the weight reduction and eventually to reduce the cost.At last,the feasibility of the design is verified by means of strength analysis and modal analysis based on the CAD model of light weighted shaft.The design applies to the load case of half shaft in independent axle,also provides technological reference for the structural lightweight design of vehicles and other machineries.
文摘With regard to function, the strengths for interference articulation of a roller shaft formed a series system. As the three strength reliabilities conditioned each other, there was a problem for the system reliability to apportion rationally. In fact, there was a transition from safety to deactivation. The state of structure was fuzziness which was in both safety and non-safety states. Therefore the reliability was a fuzzy event which considered the randomness for some design parameters and the fuzziness for the thresholds between generalized strength safety and deactivation. The mathematical model of fuzzy reliability design for the interference articulation of the roller shaft was presented. Eight design examples were calculated.
基金Sponsored by the Science and Technology Projects of Heilongjiang Province (Grant No.GB07C20202 and LC06C16)
文摘In the paper the three-dimensional flow fields are numerically simulated in the vertical-shaft mechanical mix tank of a water treatment plant by means of FLUENT software based on the method of Computational Fluid Dynamics (CFD). The influences of design parameters on flow fields and the mixing effect are analyzed. Firstly,the prediction capability of the turbulence model adopted in simulations is evaluated. And then,the mesh independence is checked up. Finally,the flow fields in various dimensionless blade diameters and dimensionless shaft spans are numerically simulated respectively. The results have shown that the numerical simulation method based on CFD is a feasible assistance for the optimal designs of mixers. Moreover,the optimal design of the blade diameter should take into account both the flow field and the power consumption. The optimization of the shaft span is to achieve a relatively even distribution of the flow field without any rupture. With the consideration of an optimal design,the dimensionless blade diameter and dimensionless shaft span should be 0.45 and 0.57 respectively in the case.
