Response of Rice Cultivars to Elevated Air Temperature and Soil Amendments: Implications towards Climate Change Adaptations and Mitigating Global Warming Potentials

Global mean surface air temperature is expected to increase 1.1˚C - 6.4˚C by the end of 21st century which may affect rice productivity and methane emissions in the future climate. This experiment was conducted to investigate the response of rice cultivars to elevated air temperature (+1.5˚C higher than ambient) and soil amendments in regards to rice yield, yield scaled methane emissions and global warming potentials. The experimental findings revealed that replacement of inorganic fertilizers (20% - 40% of recommended NPKS) with Vermicompost, Azolla biofertilizer, enriched sugarcane pressmud, rice husk biochar and silicate fertilization increased rice yield 13.0% - 23.0%, and 11.0% - 19.0% during wet aman and dry boro season, respectively. However, seasonal cumulative CH4 fluxes were decreased by 9.0% - 25.0% and 5.0% - 19.0% during rainfed wet aman and irrigated dry boro rice cultivation, respectively with selected soil amendments. The maximum reduction in seasonal cumulative CH4 flux (19.0% - 25.0%) was recorded with silicate fertilization and azolla biofertilizer amendments (9.0% - 13.0%), whereas maximum grain yield increment 10.0 % - 14.0% was found with Vermicompost and Sugarcane pressmud amendments compared to chemical fertilization (100% NPKS) treated soils at ambient air temperature. However, rice grain yield decreased drastically 43.0% - 50.0% at elevated air temperature (3˚C higher than ambient air temperature), eventhough accelerated the total cumulative CH4 flux as well as GWPs in all treatments. Maximum seasonal mean GWPs were calculated at 391.0 kg CO2 eq·ha−1 in rice husk biochar followed by sugarcane pressmud (mean GWP 387.0 kg CO2 eq·ha−1), while least GWPs were calculated at 285 - 305 kg CO2 eq·ha−1 with silicate fertilizer and Azolla biofertilizer amendments. Rice cultivar BRRI dhan 87 revealed comparatively higher seasonal cumulative CH4 fluxes, yield scaled CH4 flux and GWPs than BRRI dhan 71 during wet aman rice growing season;while BRRI dhan 89 showed higher cumulative CH4 flux and GWPs than BINA dhan 10 during irrigated boro rice cultivation. Conclusively, inorganic fertilizers may be partially (20% - 40% of the recommended NPKS) replaced with Vermicompost, azolla biofertilizer, silicate fertilizer and enriched sugarcane pressmud compost for sustainable rice production and decreasing GWPs under elevated air temperature condition.

Effects of planting patterns plastic film mulching on soil temperature,moisture, functional bacteria and yield of winter wheat in the Loess Plateau of China

The yield of winter wheat is hindered by drought and low temperature in the Loess Plateau of China.Two common mulching methods to conserve soil moisture,ridge furrows with plastic film mulching (RP) and flat soil surfaces with plastic film mulching (FP) are helpful for wheat production.Our previous study indicated that FP could improve wheat yield more effectively than RP,but the reason remains unclear.The effect of mulching method on functional bacteria also needs to be further studied.In this study,winter wheat was employed to evaluate the impacts of mulching method on soil temperature,moisture content,microorganisms and grain yield.The results showed that FP had a warming effect when the soil temperature was low and a cooling effect when the temperature was too high.However,the ability to regulate soil temperature in the RP method was unstable and varied with year.The lowest negative accumulated soil temperature was found in the FP treatment,which was 20–89 and 43–99%lower than that of the RP and flat sowing with non-film mulching control (NP) treatments,respectively.Deep soil moisture was better transferred to topsoil for wheat growth in the FP and RP treatments than the NP treatment,which made the topsoil moisture in the two treatments (especially FP) more sufficient than that in the NP treatment during the early growing stage of wheat.However,due to the limited water resources in the study area,there was almost no difference between treatments in topsoil water storage during the later stage.The wheat yield in the FP treatment was significantly higher,by 12–16and 23–56%,respectively,than in the RP and NP treatments.Significant positive correlations were observed among the negative accumulated soil temperature,spike number and wheat yield.The Chao1 and Shannon indices in the RP treatment were 17 and 3.9%higher than those in the NP treatment,respectively.However,according to network relationship analysis,the interspecific relationships of bacteria were weakened in the RP treatment.Phosphorus solubilizing,ammonification and nitrification bacteria were more active in the RP than in the FP treatment,and microbes with nitrate reduction ability and plant pathogens were inhibited in the RP treatment,which improved nutrient availability and habitat for wheat.

Predicting and delineating soil temperature regimes of China using pedotransfer function

Soil temperature regime(STR)is important for soil classification and land use.Generally,STR is delineated by estimating the mean annual soil temperature at a depth of 50 cm(MAST50)according to the Chinese Soil Taxonomy(CST).However,delineating the STR of China remains a challenge due to the difficulties in accurately estimating MAST50.The objectives of this study were to explore environmental factors that influence the spatial variation of MAST50 and generate an STR map for China.Soil temperature measurements at 40 and 80 cm depth were collected from 386 National Meteorological Stations in China during 1971–2000.The MAST50 was calculated as the average mean annual soil temperature(MAST)from 1971–2000 between 40 and 80 cm depths.In addition,2048 mean annual air temperature(MAAT)measurements from 1971 to 2000 were collected from the National Meteorological Stations across China.A zonal pedotransfer function(PTF)was developed based on the ensemble linear regression kriging model to predict the MAST50 in three topographic steps of China.The results showed that MAAT was the most important variable related to the variation of MAST50.The zonal PTF was evaluated with a 10%validation dataset with a mean absolute error(MAE)of 0.66°C and root mean square error(RMSE)of 0.78°C,which were smaller than the unified model with MAE of 0.83°C and RMSE of 0.96°C,respectively.This study demonstrated that the zonal PTF helped improve the accuracy of the predicted MAST50 map.Based on the prediction results,an STR map across China was generated to provide a consistent scientific base for the improvement and application of CST and land use support.

Effects of soil temperature and soil water content on soil respiration in three forest types in Changbai Mountain

Soil incubation experiments were conducted in lab to delineate the effect of soil temperature and soil water content on soil respirations in broad-leaved/Korean pine forest (mountain dark brown forest soil), dark coniferous forest (mountain brown coniferous forest soil) and erman's birch forest (mountain soddy forest soil) in Changbai Mountain in September 2001. The soil water content was adjusted to five different levels (9%, 21%, 30%, and 43%) by adding certain amount of water into the soil cylinders, and the soil sample was incubated at 0, 5, 15, 25 and 35°C for 24 h. The results indicated that in broad-leaved/Korean pine forest the soil respiration rate was positively correlated to soil temperature from 0 to 35°C. Soil respiration rate increased with increase of soil water content within the limits of 21% to 37%, while it decreased with soil water content when water content was over the range. The result suggested the interactive effects of temperature and water content on soil respiration. There were significant differences in soil respiration among the various forest types. The soil respiration rate was highest in broad-leaved/Korean pine forest, middle in erman's birch forest and the lowest in dark coniferous forest. The optimal soil temperature and soil water content for soil respiration was 35°C and 37% in broad-leaved/Korean pine forest, 25°C and 21% in dark coniferous forest, and 35°C and 37% in erman's birch forest. Because the forests of broad-leaved/Korean pine, dark coniferous and erman's birch are distributed at different altitudes, the soil temperature had 4–5°C variation in different forest types during the same period. Thus, the soil respiration rates measured in brown pine mountain soil were lower than those in dark brown forest and those measured in mountain grass forest soil were higher than those in brown pine mountain soil. Key words Soil temperature - Soil water content - Soil respiration - The typical forest ecosystem in Changbai Mountain CLC number S7118.51 Document code A Foundation item: This study was supported by grant from the National Natural Science Foundation of China (No. 30271068), the grant of the Knowledge Innovation Program of Chinese Academy of Sciences (KZ-CX-SW-01-01B-12) and the grant from Advanced Programs of Institute of Applied Ecology Chinese Academy of Sciences.Biography: WANG Miao (1964-), male, associate professor in Institute of Applied Ecology, Chinese Academy of Science, Shenyang 110016, P. R. China.Responsible editor: Song Funan

Effects of Land Cover on Soil Temperature,Humidity and Moisture in Phoebe bournei Forest

Under the condition of high temperature, the effects of five cover patterns （clean tillage, film mulching, weed covering, branches and leaves covering and growing grass covering） on soil properties in young Phoebe boumei forest were in- vestigated. The results showed that the five cover patterns all showed significant ef- fects on soil properties in young Phoebe bournei forest under the condition of high temperature. Land cover increased land temperature in Phoebe boumei forest. Un- der the film mulching, the land temperature was increased most rapidly with the largest increment. However, weed covering, branches and leaves covering and growing grass covering decreased land temperature. Among them, growing grass covering showed the best cooling effect. The film mulching, weed covering, branch- es and leaves covering and growing grass covering all increased land humidity. The film mulching showed the best moisture-preserving effect in the early period, but in the late period, the humidity in the film mulching treatment group was lower than that in the clean tillage treatment group. Among the five mulching patterns, moisture loss in the film mulching treatment group was slowest and least, followed by those in the weed covering and branches and leaves covering treatment groups, and moisture loss in the growing grass covering treatment group was fastest and most.

Effects of Different Plastic films Mulching on Soil Temperature and Moisture, the Growth and Yield of Sugarcane

[Objective] The effects of different plastic films mulching on soil temperature and moisture, and growth and yield of sugarcane were discussed in order to provide references for using different plastic film in sugarcane pro-duction. [Method]Four kinds of plastic films viz., normal colorless transparent plastic film, milky photodegradation weeding plastic film, black plastic film and gray-black plastic film were used in sugarcane cultivation by using no film mulching as the control. Soil temperature and moisture were measured during plastic film mulching period, and sugarcane agronomic traits such as emergence rate, tillering rate, plant hight, stalk diameter and effective stalk number were investigated during growth period, the cane yield and economic benefits were calculated during harvest period. [Result] The results showed that plastic film mulching could significantly increase soil temperature and moisture. Com-pared with the control, soil temperature was increased by 0.3-0.8 ℃ in three plastic films mulching treatment except for gray-black plastic film mulching. The soil moisture of all mulching treatments was 10.1%-17.4% higher than the control. Furthermore, the seedling emergence rate, tillering rate, effective stalk number and cane yield also could be improved using plastic film mulching,which were increased by 0.8%-9.9%, 20.6%-34.9%, 5190-10980 stalks/hm^2and6.4%-14.9% as compared to the control,while plant height and stalk diameter were found to be no significant effect by plastic film mulching. The results of benefit analysis indicated that, milky photodegradation weeding film mulching had the highest economic benefit, the second were normal colorless transparent plastic film mulching and black plastic film mulching, which were 5 987.2, 1 876.5 and 1 813.5 Yuan/hm^2 higher than the control. The gray-black film mulching treatment had poor benefit.[Conclusion] The milky photodegradation weeding plastic film could be vigorously extended in sugarcane production. Normal colorless transparent plastic film and black plastic film could be ex-tended gradually as a new kind of plastic film. The grayblack film should not be used for its higher cost and more thickness.

Influence of Temperature on the Inter-pressure of Soil Water Tension with Correcting Method

When the electronic temperature sensor was incorporated into a system of soil water tension and the insidetube temperature was monitored in real time, it is concluded that the inside temperature increased by 26.9 ℃ and the inside pressure changed about 14.6 Kpa, when the pottery soil was replaced by the sealing plug. When the soil water was relatively stable in the experimental salvers, the in-side pressure stil varied regularly with the temperature. When the inside temperature increased by 22.2 ℃, the inside pressure varied about 7.4 Kpa. Through com-pensation calculation of the inside tension, the temperature in the warming and cooling periods was compensated, which was useful to correct the tension measurement errors induced from the changing temperature. When the measuring interval was 4 hours and the temperature difference was 18.1 ℃, the tension difference of both points was only 0.278 Kpa, compared to the difference up to 6.5 Kpa before compensation.

Improving maize growth and development simulation by integrating temperature compensatory effect under plastic film mulching into the AquaCrop model

Temperature compensatory effect, which quantifies the increase in cumulative air temperature from soil temperature increase caused by mulching, provides an effective method for incorporating soil temperature into crop models. In this study, compensated temperature was integrated into the AquaCrop model to investigate the capability of the compensatory effect to improve assessment of the promotion of maize growth and development by plastic film mulching(PM). A three-year experiment was conducted from2014 to 2016 with two maize varieties(spring and summer) and two mulching conditions(PM and non-mulching(NM)), and the AquaCrop model was employed to reproduce crop growth and yield responses to changes in NM, PM, and compensated PM. A marked difference in soil temperature between NM and PM was observed before 50 days after sowing(DAS) during three growing seasons. During sowing–emergence and emergence–tasseling, the increase in air temperature was proportional to the compensatory coefficient, with spring maize showing a higher compensatory temperature than summer maize. Simulation results for canopy cover(CC) were generally in good agreement with the measurements, whereas predictions of aboveground biomass and grain yield under PM indicated large underestimates from 60 DAS to the end of maturity. Simulations of spring maize biomass and yield showed general increase based on temperature compensation, accompanied by improvement in modeling accuracy, with RMSEs decreasing from 2.5 to 1.6 t ha^(-1)and from 4.1 t to 3.4 t ha^(-1). Improvement in biomass and yield simulation was less pronounced for summer than for spring maize, implying that crops grown during low-temperature periods would benefit more from the compensatory effect. This study demonstrated the effectiveness of the temperature compensatory effect to improve the performance of the AquaCrop model in simulating maize growth under PM practices.

Thermal integrity profiling of cast-in-situ piles in sand using fiber-optic distributed temperature sensing

Defects in cast-in-situ piles have an adverse impact on load transfer at the pile‒soil interface and pile bearing capacity. In recent years, thermal integrity profiling (TIP) has been developed to measure temperature profiles of cast-in-situ piles, enabling the detection of structural defects or anomalies at the early stage of construction. However, using this integrity testing method to evaluate potential defects in cast-in-situ piles requires a comprehensive understanding of the mechanism of hydration heat transfer from piles to surrounding soils. In this study, small-scale model tests were conducted in laboratory to investigate the performance of TIP in detecting pile integrity. Fiber-optic distributed temperature sensing (DTS) technology was used to monitor detailed temperature variations along model piles in sand. Additionally, sensors were installed in sand to measure water content and matric suction. An interpretation method against available DTS-based thermal profiles was proposed to reveal the potential defective regions. It shows that the temperature difference between normal and defective piles is more obvious in wet sand. In addition, there is a critical zone of water migration in sand due to the water absorption behavior of cement and temperature transfer-induced water migration in the early-age concrete setting. These findings could provide important insight into the improvement of the TIP testing method for field applications.

Effects of temperature and surfactants on naphthalene and phenanthrene sorption by soil

Adsorption experiments were carried out to investigate the sorption behaviors of naphthalene and phenanthrene in six different soils and to determine the effects of temperature, linear alkylbenzene sulfonate （LAS） and cetylrimethyl ammonium bromide （CTAB） on sorption. The results show that for a given sorbent phenanthrene exhibited greater nonlinear and stronger sorption than naphthalene. There was a strong negative correlation for the Koc values with organic carbon content （foc）. The increase of temperature was not favorable to sorption. Sorption decreased along with the increasing aqueous LAS concentration from 0 to 1000 mg/L. At low CTAB concentration （〈 100 mg/L）, the adsorption increased as CTAB hemimicelles formed on the soil surface. At high concentration, CTAB decreased the adsorption by occupying active hydrophobic adsorption sites and solubilization of naphthalene and phenanthrene.

Interactive effects of soil temperature and moisture on soil N mineralization in a Stipa krylovii grassland in Inner Mongolia, China

Determining soil N mineralization response to soil temperature and moisture changes is challenging in the field due to complicated effects from other factors. In the laboratory, N mineralization is highly dependent on temperature, moisture and sample size. In this study, a laboratory incubation experiment was carefully designed and conducted under controlled conditions to examine the effects of soil temperature and moisture on soil N mineralization using soil samples obtained from the Stipa krylovii grassland in Inner Mongolia, China. Five temperature（i.e. 9℃, 14℃, 22℃, 30℃ and 40℃） and five moisture levels（i.e. 20%, 40%, 60%, 80% and 100% WHC, where WHC is the soil water holding capacity） were included in a full-factorial design. During the 71-day incubation period, microbial biomass carbon（MBC）, ammonium nitrogen（NH4 ^＋-N） and nitrate nitrogen（NO3^--N） were measured approximately every 18 days; soil basal respiration for qCO2 index was measured once every 2 days（once a week near the end of the incubation period）. The results showed that the mineral N production and net N mineralization rates were positively correlated with temperature; the strongest correlation was observed for temperatures between 30℃ and 40℃. The relationships between moisture levels and both the mineral N production and net N mineralization rates were quadratic. The interaction between soil temperature and moisture was significant on N mineralization, i.e. increasing temperatures（moisture） enhanced the sensitivity of N mineralization to moisture（temperature）. Our results also showed a positive correlation between the net nitrification rate and temperature, while the correlation between the NH4 ^＋-N content and temperature was insignificant. The net nitrification rate was negatively correlated with high NH4 ^＋-N contents at 80%–100% WHC, suggesting an active denitrification in moist conditions. Moreover, qCO2 index was positively correlated with temperature, especially at 80% WHC. With a low net nitrification rate and high soil basal respiration rate, it was likely that the denitrification concealed the microbial gross mineralization activity; therefore, active soil N mineralization occurred in 60%–80% WHC conditions.

Relationship Between Canopy Temperature at Flowering Stage and Soil Water Content,Yield Components in Rice

The canopy temperature of rice at the flowering stage and the soil water content were investigated under different soil water treatments （the soil water contents were 24%, 55%, 90% and 175% at the flowering stage）. The canopy temperature was lower than air temperature, and the soil water content significantly influenced the canopy temperature. The lower the soil water content, the higher the canopy temperature, the less the accumulative absolute value of canopy-air temperature difference. Moreover, the maximum difference between treatments and CK in the accumulative absolute value of canopy-air temperature difference appeared at 13：00 μm. in a day, thus, it could be considered as a suitable measuring time. Under the lowest water content treatment, the peak flowering occurred in the first three days （about 70% of panicles flowered）, resulting in shortened and lightened panicle of rice. As to the CK and the high water content treatments, the peak flowering appeared in the middle of flowering duration, with longer panicle length and higher panicle weight. Results indicated the lower the soil water content, the less the filled grain number and grain yield.

Alternate row mulching optimizes soil temperature and water conditions and improves wheat yield in dryland farming

Straw mulching allows for effective water storage in dryland wheat production. Finding a suitable straw mulching model that facilitates wheat growth was the objective of this study. A 2-year field experiment was conducted to investigate the effects of two straw mulching patterns （FM, full coverage within all the rows; HM, half coverage within alternate rows） and two mulching rates （4.5 and 9.0 t ha^-1） on soil moisture, soil temperature, grain yield, and water use efficiency （WUE） of winter wheat in northern China, with no mulching （M0） as the control. Results showed that mulching increased the soil water storage in all growth stages under high mulching rates, with a stronger effect in later growth stages. Water storage under the HM model was greater in later stages than under the FM model. Soil water content of HM groups was higher than that of FM groups, especially in surface soil layers. Evapotranspiration decreased in mulched groups and was higher under high mulching rates. Aboveground biomass during each growth stage under the HM model was higher than that under M0 and FM models with the same mulched rate, leading to a relatively higher grain yield under the HM model. Mulching increased WUE, a trend that was more obvious under HM9.0 treatment. Warming effect of soil temperature under the HM pattern persisted longer than under the FM model with the same mulching rates. Accumulated soil temperature under mulched treatments increased, and the period of negative soil temperature decreased by 9-12 days under FM and by 10-20 days under HM. Thus, the HM pattern with 9.0 t ha^-1 mulching rate is beneficial for both soil temperature and water content management and can contribute to high yields and high WUE for wheat production in China.

Film-mulched continuous ridge-furrow planting improves soil temperature,nutrient content and enzymatic activity in a winter oilseed rape field,Northwest China

Film mulching system is a widely employed agricultural practice worldwide. However, the effects of different planting and mulching patterns on soil nutrient content and enzymatic activity have not been well documented. In this study, we examined the impact of four planting and mulching patterns（including control, flat planting without mulching; M1, flat planting with film mulching; M2, ridge-furrow planting with film mulching on both ridges and furrows; and M3, ridge-furrow planting with film mulching on continuous ridges） on the seed yield of winter oilseed rape, soil moisture, soil temperature, soil organic carbon（SOC） content, soil nutrient content, and soil enzymatic activity over three growing seasons from 2012 to 2015 in a winter oilseed rape field in the semi-arid area of Northwest China. Seed yield of winter oilseed rape, soil moisture, soil temperature, enzymatic activities, and contents of nitrate-nitrogen, available phosphorus, and available potassium were all significantly higher in mulching treatments（M1, M2 and M3） than in control treatment over the three growing seasons, whereas SOC content was significantly lower in mulching treatments than in control treatment during 2013–2014 and 2014–2015. Among the three mulching treatments（M1, M2 and M3）, the M3 treatment showed consistently higher seed yield, SOC content, nutrient contents, and enzymatic activities than the other two treatments. Seed yield of winter oilseed rape was 41.1% and 15.0% higher in M3 than in M1 and M2, respectively. SOC content and soil enzymatic activities in the top 0–20 cm soil layers and nitrate-nitrogen content in the top 0–30 cm soil layers were all significantly higher in M3 than in M1 and M2. Therefore, we advise the ridge-furrow planting with film mulching on continuous ridges（i.e., M3） as an efficient planting and mulching pattern for sustainably improving the seed yield of winter oilseed rape and preserving soil fertility in the semi-arid area of Northwest China.

Responses of chlorophyll fluorescence and nitrogen level of Leymus chinensis seedling to changes of soil moisture and temperature

Controlled experiment of Leymus chinensis seedlings grown in the environmental growth chambers at 3 soil moisture levels and 3 temperature levels was conducted in order to improve the understanding how leaf photosynthetic parameters will respond to climatic change. The results indicated that soil drought and high temperature decreased the photochemical efficiency of photosystem(F v/F m), the overall photochemical quantum yield of PSII(yield), the coefficient of photochemical fluorescence quenching(q\-P), but increased the coefficient of non-photochemical fluorescence quenching(q\-N). Severe soil drought would decrease F v/F m and yield by 3.12% and 37.04% under 26℃ condition, respectively, and 6.60% and 73.33% under 32℃ condition, respectively, suggesting that higher temperature may enhance the negative effects of soil drought. All the soil drought treatments resulted in the decline in leaf nitrogen content. There was no significant effect of temperature on leaf nitrogen level, but higher temperature significantly reduced the root nitrogen content and the ratio of root nitrogen to leaf nitrogen, indicating the different strategies of adaptation to soil drought and temperature. It was also implied that higher temperature would enhance the effect of soil drought on leaf photosynthetic capacity, decrease the adaptability of Leymus chinensis to drought.

Analysis of temperature field characteristics based on subgrade site measurements of Harbin-Qiqihar High-speed Railway in a deep seasonal frozen soil region

Recent years have seen a large number of high-speed railways built and will be built in seasonal frozen soil regions ot China. Although high-speed railways are characterized by being fast, comfortable and safe, higher standards for defor- mation of the railways＇ frozen subgrade are required. Meanwhile, changes in subgrade soil temperatures are the main factors affecting the deformation of frozen subgrade. Therefore, this paper selected typical test subgrade sections of the Harbin-Qiqihar Line, a special line for passenger transport built in the deep seasonal frozen soil regions of China, to monitor field temperatures. Also, the temperature changing laws of railways＇ subgrade in this region was analyzed by using testing data, the aim of which is to provide a technical support for future design and construction of buildings and structures in a deep seasonal frozen soil region.

FACTORS AFFECTING SOIL RESPIRATION IN REFERENCE WITH TEMPERATURE'S ROLE IN THE GLOBAL SCALE

Soil respiration is CO 2 evolution process from soil to atmosphere, mainly produced by soil micro organism and plant roots. It is affected not only by biological factors (vegetation, micro organism, etc.) and environmental factors (temperature, moisture, pH, etc.), but also more and more strongly by man made factors. Based on literature survey, main factors affecting soil respiration were reviewed. The relationships of soil respiration to latitude and to mean annual temperature were analyzed by using the data measured from forest vegetation in the world. As a result, soil respiration rate decreased exponentially with an increase of latitude, and increased with increasing temperature. Following the relationship between soil respiration and temperature, Q 10 value (law of Van Hoff) was obtained as 1.57 in the global scale.

Effect of temperature on soil respiration in a Chinese fir forest

Soil samples collected from the surface soil （0-10 cm） in an 88-year-old Chinese fir （Cunninghamia lanceolata） forest in Nanping Fujian, China were incubated for 90 days at the temperatures of 15℃, 25℃ and 35℃ in laboratory. The soil CO2 evolution rates were measured at the incubation time of 2, 5, 10, 15, 20, 25, 30, 35, 40, 50, 60, 70, 80 and 90 days. The results showed that CO2 evolution rates of soil samples varied significantly with incubation time and temperature during the incubation period. Mean CO2 evolution rate and cumulative amount of CO2 evolution from soil were highest at 35℃, followed by those at 25℃, and 15℃. Substantial differences in CO2 evolution rate were found in Q10 values calculated for the 2nd and 90th day of incubation. The Q10 value for the average CO2 evolution rate was 2.0 at the temperature range of 15-25℃, but it decreased to 1.2 at 25 35℃. Soil CO2 evolution rates decreased with the incubation time. The cumulative mineralized C at the end of incubation period （on the 90th day） was less than 10% of the initial C amounts prior to incubation.

Improved simulation of carbon and water fluxes by assimilating multi-layer soil temperature and moisture into process-based biogeochemical model

Background: Soil temperature and moisture are sensitive indicators in soil organic matter decomposition because they control global carbon and water cycles and their potential feedback to climatic variations. Although the Biome-Biogeochemical Cycles (Biome-BGC) model is broadly applied in simulating forest carbon and water fluxes, its single-layer soil module cannot represent vertical variations in soil moisture. This study introduces the Biome-BGC MuSo model, which is composed of a multi-layer soil module and new modules pertaining to phenology and management for simulations of carbon and water fluxes. Although this model considers soil processes among active layers, estimates of soil-related variables might be biased, leading to inaccurate estimates of carbon and water fluxes. Methods: To improve the estimations of soil-related processes in Biome-BGC MuSo, this study assimilates ground-measured multi-layer daily soil temperature and moisture at the Changbai Mountains forest flux site by using the Ensemble Kalman Filter algorithm. The modeled estimates of water and carbon fluxes were evaluated with measurements using determination coefficient (R2) and root mean square error (RMSE). The differences in the RMSEs from Biome-BGC MuSo and the assimilated Biome-BGC MuSo were calculated (ΔRMSE), and the relationships between ΔRMSE and the climatic and biophysical factors were analyzed. Results: Compared with the original Biome-BGC model, Biome-BGC MuSo improved the simulations of ecosystem respiration (ER), net ecosystem exchange (NEE) and evapotranspiration (ET). Data assimilation of the soil-related variables into Biome-BGC MuSo in real time improved the accuracies of the simulated carbon and water fluxes (ET: R^2=0.81, RMSE=0.70 mm·d^-1;ER: R^2=0.85, RMSE=1.97 gC·m^-2·d^-1;NEE: R^2=0.70, RMSE=1.16 gC·m^-2·d^-1). Conclusions: This study proved that seasonal simulation of carbon and water fluxes are more accurate when using Biome-BGC MuSo with a multi-layer soil module than using Biome-BGC with a single-layer soil module. Moreover, assimilating the observed soil temperature and moisture data into Biome-BGC MuSo improved the modeled estimates of water and carbon fluxes via calibrated soil-related simulations. The assimilation strategy is applicable to various climatic and biophysical conditions, particularly densely forested areas, and for local or regional simulation.

Deformation properties of chloride saline soil under action of a low-temperature environment and different loads

To find the deformation properties of chloride saline soil under the influence of a low temperature environment and different loads,two types of chloride saline soil were selected and their deformation process was tested in the laboratory and analyzed during the cooling process in the sensitive cryogenic temperature range.The research results show that high-chloride-salt saline soil underwent little volume change under the no-load condition during the cooling process.Under staticload and dynamic-load conditions,different degrees of settlement deformation occurred;throughout the entire cooling process,another chloride saline soil with a high proportion of sulfate salt underwent volume expansion under no-load and static-load conditions.Under the no-load condition,a certain degree of settlement deformation occurred.Deformation properties were evaluated at different time points during the cooling process for two kinds of chloride saline soil.Finally,deformation characteristics of chloride saline soil were analyzed from the perspective of salt type and crystallization variation under the action of a low-temperature environment and different loads.