INFLUENCE OF SUPERPLASED SHAPE MEMORY ALLOY ON ITSMEMORY EFFECT

An investigation has been made on the fine grain supeoplasticity of alloy, Cu-26.69%Zn-3.82% Al and its effect of superpolastic deformation (SPD) on the shape memory effect (SME).This alloy has the behavior of the fine grain superplasticity and SME simultaneousty. The rolledstructure of the alloy obtains equiaxial grains after the supeaplastic pretreatment. The alloy presentsmaximum total elogation of 545%, at the deformation temperature of 600℃ and the tensile rate of0.5mm / min. After supeperplastic deformation, the memory effect of the alloy is remarkably im-proved, the angle recovery rate and the enthalpies of transformation increase, the attenuation ofSME decreases, and the characteristic temperatures are lowered.

Influence of recovery heating rate on shape memory effect in up-quenched Cu-Al-Mn alloy

The effect of recovery heating rate on shape memory effect of the up-quenched Cu-8.88Al-10.27Mn（mass fraction, %） alloy was investigated by optical microscopy, electron transmission microscopy（TEM） and electrical resistivity measurement. It is found that the shape recovery rate decreases as the heating rate decreases. It can reach 75% when the heating rate is 20 ℃/min, while it is only 8% when the heating rate is 1 ℃/min. In situ microstructure observation indicates that the dependence of shape memory effect on recovery heating rate is caused by the stabilization of twinned martensite induced by deformation. The analysis of electrical resistivity shows that the stabilization of twinned martensite may be ascribed to formation of compound defects of vacancies and dislocations at the boundaries of twinned martensite during the slow heating. The compound defects prevent the reverse transformation of twinned martensite.

Role of thermal martensite in shape memory effect of CoAl and CoNi alloys

To address the role of the HCP martensite in CoAl and CoNi shape memory alloys, the relationship between the shape memory effect （SME） and the content of the thermal and stress-induced HCP martensite was investigated in the solution-treated CoAl and CoNi alloys. In-situ optical observations were employed to investigate the contents of thermal HCP martensite before and after deep cooling and its influence on the stress-induced HCP martensite transformation and SME. The results show that the SME in both the CoAl and the CoNi alloys results from the stress-induced HCP martensite. The role of the thermal HCP martensite in both of them is the strengthening of the matrix. The much higher yield strength in the solution-treated CoAl alloy due to solution strengthening of Al is responsible for its better SME compared with the CoNi alloy.

SHAPE MEMORY EFFECT OF PU IONOMERS WITH IONIC GROUPS ON HARD-SEGMENTS

SMPU （shape memory polyurethane） non-ionomers and ionomers, synthesized with poly（c-caprolactone） （PCL）, 4, 4＇-diphenylmethane diisocyanate （MDI）, 1,4-butanediol （BDO）, dimethylolpropionic acid （DMPA） were measured with cyclic tensile test and strain recovery test. The relations between the structure and shape memory effect of these two series were studied with respect to the ionic group content and the effect of neutralization. The resulting data indicate that, with the introduction of asymmetrical extender, the stress at 100% elongation is decreased for PU non-ionomer and ionomer series, especially lowered sharply for non-ionomer series; the fixation ratio of ionomer series is not affected obviously by the ionic group content; the total recovery ratio of ionomer series is decreased greatly. After sufficient relaxation time for samples stretched beforehand, the switching temperature is raised slightly, whereas the recovery ratio measured with strain recovery test method is lowered with increased DMPA content. The characterization with FT-IR, DSC, DMA elucidated that, the ordered hard domain of the two series is disrupted with the introduction of DMPA which causes more hard segments to dissolve in soft phase; ionic groups on hard segment enhance the cohesion between hard segments especially at high ionic group content and significantly facilitate the phase separation compared with the corresponding non-ionomer at moderate ionic group content.

A macroscopic multi-mechanism based constitutive model for the thermo-mechanical cyclic degeneration of shape memory effect of NiTi shape memory alloy

A macroscopic based multi-mechanism constitutive model is constructed in the framework of irreversible thermodynamics to describe the degeneration of shape memory effect occurring in the thermo-mechanical cyclic deformation of NiTi shape memory alloys (SMAs). Three phases, austenite A, twinned martensite and detwinned martensite , as well as the phase transitions occurring between each pair of phases (, , , , and are considered in the proposed model. Meanwhile, two kinds of inelastic deformation mechanisms, martensite transformation-induced plasticity and reorientation-induced plasticity, are used to explain the degeneration of shape memory effects of NiTi SMAs. The evolution equations of internal variables are proposed by attributing the degeneration of shape memory effect to the interaction between the three phases (A, , and and plastic deformation. Finally, the capability of the proposed model is verified by comparing the predictions with the experimental results of NiTi SMAs. It is shown that the degeneration of shape memory effect and its dependence on the loading level can be reasonably described by the proposed model.

STABILIZATION OF MARTENSITE IN Cu-Zn-Al ALLOY AND ITS REVERSE SHAPE MEMORY EFFECT

ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅｓｔａｂｉｌｉｚａｔｉｏｎｏｆｍａｒｔｅｎｓｉｔｅｒｅｆｅｒｓｔｏｔｈｅｐｈｅｎｏｍｅｎｏｎｔｈａｔｔｈｅｒｅｖｅｒｓｅｔｒａｎｓｆｏｒｍａｔｉｏｎｓｔａｒｔａｎｄｆｉｎｉｓｈｔｅｍｐｅｒａｔｕｒｅｓ（ＡｓａｎｄＡｆ）ｉ...

Buckling-controlled two-way shape memory effect in a ring-shaped bilayer

Shape memory polymers(SMPs)usually have a one-way shape memory effect.In this paper,an easy-operating method to realize a two-way shape memory effect was demonstrated in a ring-shaped bilayer structure where the two layers are SMPs with different thermal transition temperatures.By designing specific thermomechanical processes,the mismatched deformation between the two layers leads to a morphology change of ring-shaped bilayer structures from a smooth ring to a gear-like buckling shape under cooling and a reversible recovery to the smooth shape under heating.Such a morphology change is ascribed to occurrence and recovery of thermoelastic buckling.This method was validated by finite element simulation.We experimentally investigated the influence of pre-strain on buckling,and it was found that both the buckling occurrence and recovery temperature vary with pre-strain.Furthermore,considering a ring-shaped SMP-SMP bilayer structure,finite element analysis was conducted to study the influence of film thickness and modulus ratio of two layers on buckling behavior.The results showed that the critical buckling wavelength was greatly influenced by film thickness and modulus ratio.W e made a theoretical analysis that accorded well with the numerical results.

Effects of Predeformation on the Reverse Martensitic Transformation of TiNi Shape Memory Alloy

DSC was used to study the effects of predeformation on the reverse martensitic transformation of near-equiatomic TiNi alloy. Both the start temperature As and the finish temperature Af of the reverse transformation increased with increasing degree of predeformation, but the algebraic difference between As and Af decreased with increasing predeformation until it reached a minimum value, then remained unchanged with further deformation. Transformation heat also increased with increasing predeformation until it reached a maximum value, then decreased with further predeformation. All the phenomena above were considered to be closely related with the release of elastic strain energy during predeformation.

EFFECTS OF HEAT TREATMENT ON TENSILE PROPERTIES AND SHAPE MEMORY EFFECTS OF Ni-Ti-Nb ALLOY

ＥＦＦＥＣＴＳＯＦＨＥＡＴＴＲＥＡＴＭＥＮＴＯＮＴＥＮＳＩＬＥＰＲＯＰＥＲＴＩＥＳＡＮＤＳＨＡＰＥＭＥＭＯＲＹＥＦＦＥＣＴＳＯＦＮｉＴｉＮｂＡＬＬＯＹ①ＺｈｅｎｇＹｕｆｅｎｇ，ＣａｉＷｅｉ，ＬｕｏＹｉｃｈｕｎ，ＺｈａｏＬｉａｎｃｈｅｎｇＳｃｈｏｏ...

EFFECT OF DYNAMIC RECRYSTALLIZATION ON SHAPE MEMORY EFFECT IN Fe－Mn－Si BASED ALLOYS

Improvement of shape, memory effect (SME) in Fe-Mn-Si based alloys has been investigated, compared with that by conventional 'training' treatment. It is found that SME in Fe-Mn-Si alloy can be greatly improved by ausforming and 3.8%recovery strain and 2.2% complete recovery strain can be reached by ausforming at 973 K when dynamic recrystallization has just occurred. The mechanism for the improvement of SME is proposed.

Effects of Ta Addition on NiTi Shape Memory Alloys

The effect of Ta addition on the martensitic transformation characteristics and the X-ray visibility on NiTi shape memory alloy have been studied in (Ni51Ti49)1-xTax system. It was found that the transformation temperatures of the Ni51Ti49 binary alloy increased drastically by an addition of 0～4 at. pet Ta, but only slightly when the concentration exceeded 4 at. pct; the addition of Ta greatly decreases the sensitivity of the martensitic transformations to the variation in the Ni-Ti ratio. The addition of Ta to the NiTi binary alloy can improve its X-ray visibility.

Compressive mechanical properties and shape memory effect of NiTi gradient lattice structures fabricated by laser powder bed fusion

Laser additive manufacturing (AM) of lattice structures with light weight, excellent impact resistance, and energy absorption performance is receiving considerable attention in aerospace, transportation, and mechanical equipment application fields. In this study, we designed four gradient lattice structures (GLSs) using the topology optimization method, including the unidirectional GLS, the bi-directional increasing GLS, the bi-directional decreasing GLS and the none-GLS. All GLSs were manufactureed by laser powder bed fusion (LPBF). The uniaxial compression tests and finite element analysis were conducted to investigate the influence of gradient distribution features on deformation modes and energy absorption performance of GLSs. The results showed that, compared with the 45° shear fracture characteristic of the none-GLS, the unidirectional GLS, the bi-directional increasing GLS and the bi-directional decreasing GLS had the characteristics of the layer-by-layer fracture, showing considerably improved energy absorption capacity. The bi-directional increasing GLS showed a unique combination of shear fracture and layer-by-layer fracture, having the optimal energy absorption performance with energy absorption and specific energy absorption of 235.6 J and 9.5 J g-1 at 0.5 strain, respectively. Combined with the shape memory effect of NiTi alloy, multiple compression-heat recovery experiments were carried out to verify the shape memory function of LPBF-processed NiTi GLSs. These findings have potential value for the future design of GLSs and the realization of shape memory function of NiTi components through laser AM.

Microwave sintering effects on the microstructure and mechanical properties of Ti–51at%Ni shape memory alloys

Ti–51at%Ni shape memory alloys(SMAs) were successfully produced via a powder metallurgy and microwave sintering technique.The influence of sintering parameters on porosity reduction,microstructure,phase transformation temperatures,and mechanical properties were investigated by optical microscopy,field-emission scanning electron microscopy(FE-SEM),X-ray diffraction(XRD),differential scanning calorimetry(DSC),compression tests,and microhardness tests.Varying the microwave temperature and holding time was found to strongly affect the density of porosity,presence of precipitates,transformation temperatures,and mechanical properties.The lowest density and smallest pore size were observed in the Ti–51at%Ni samples sintered at 900°C for 5 min or at 900°C for 30 min.The predominant martensite phases of β2 and β19′ were observed in the microstructure of Ti–51at%Ni,and their existence varied in accordance with the sintering temperature and the holding time.In the DSC thermograms,multi-transformation peaks were observed during heating,whereas a single peak was observed during cooling;these peaks correspond to the presence of the β2,R,and β19′ phases.The maximum strength and strain among the Ti–51at%Ni SMAs were 1376 MPa and 29%,respectively,for the sample sintered at 900°C for 30 min because of this sample's minimal porosity.

Effect of Training on Two-way Shape Memory Effect and Its Stability in a Ti-Ni-Hf High Temperature Shape Memory Alloy

The Effect of the thermal cycling training under constant strain on the two-way shape memory effect (TWSME) in a Ti36l\li49Hf15 high temperature shape memory alloy (SMA) has been investigated by bending tests. The results indicated that the training procedure is beneficial to get the better TWSME. The two-way shape memory strain increases with increasing the training strain. And it decreases with increasing the training temperature. The TWSME obtained in the present alloy shows poorer stability compared with that obtained in the TiNi alloys.

Effects of aging on the microstructure of a Cu-Al-Ni-Mn shape memory alloy

The influence of aging on the microstructure and mechanical properties of Cu-11.6wt%Al-3.9wt%Ni-2.5wt%Mn shape memory alloy（SMA） was studied by means of scanning electron microscopy（SEM）,transmission electron microscopy（TEM）,X-ray diffractometer,and differential scanning calorimeter（DSC）.Experimental results show that bainite,γ2,and α phase precipitates occur with the aging effect in the alloy.After aging at 300°C,the bainitic precipitates appear at the early stages of aging,while the precipitates of γ2 phase are observed for a longer aging time.When the aging temperature increases,the bainite gradually evolves into γ2 phase and equilibrium α phase（bcc） precipitates from the remaining parent phase.Thus,the bainite,γ2,and α phases appear,while the martensite phase disappears progressively in the alloy.The bainitic precipitates decrease the reverse transformation temperature while the γ2 phase precipitates increase these temperatures with a decrease of solute content in the retained parent phase.On the other hand,these precipitations cause an increasing in hardness of the alloy.

Effect of thermal oxidation on the surface characteristics and corrosion behavior of a Ta-implanted Ti-50.6Ni shape memory alloy

A NiTi shape memory alloy （SMA） modified by Ta ion implantation was subjected to oxidation treatment in air at 723 and 873 K. Atomic force microscopy （AFM）, Auger electron spectroscopy （AES）, and grazing incidence X-ray diffraction （GIXRD） measurements were conducted to investigate the surface characteristics, including surface topography, elemental depth profiles, and surface phase structures. The surface roughness of the Ta-implanted NiTi increases after oxidation, and the higher the oxidation temperature is, the larger the value is. The surface of the Ta-implanted NiTi oxidized at 723 K is a nanolayer mainly composed of TiO2/Ta2O5 and TiO with depressed Ni content. The Ta-implanted NiTi oxidized at 873 K is mainly covered by rutile TiO2 in several micrometers of thickness. Potentiodynamic polarization tests indicated that the corrosion resistance of the Ta-implanted NiTi was improved after thermal oxidation at 723 K, but a negative impact was found for the Ta-implanted NiTi oxidized at 873 K.

Effect of heat treatment on the transformation behavior and temperature memory effect in TiNiCu wires

The effect of heat treatment on the phase transformation behavior of TiNiCu shape memory alloy wires and the temperature memory effect in this alloy were investigated by the resistance method. These results showed that with increasing annealing temperature and annealing time, the phase transformation temperatures of TiNiCu wires were shifted to higher temperatures in the heating and cooling process. It was also found that incomplete thermal cycles, upon heating the TiNiCu wires, which were arrested at a temperature between the start and finish temperatures of the reverse martensite transformation, could induce a kinetic stop in the next complete thermal cycle. The kinetic stop temperature was closely related to the previous arrested temperature. This phenomenon was defined as the temperature memory effect. The result of this study was consistent with the previous report on the phenomenon obtained using the differential scanning calorimetry method, indicating that temperature memory effect was a common phenomenon in shape memory alloys.

Microstructure,compression property and shape memory effect of Ru-Nb high temperature shape memory alloy

The microstructure,phase transformation,compression property and strain recovery characteristics of equiatomic Ru-Nb high temperature shape memory alloy were investigated by means of optical microscope,X-ray diffraction(XRD),differential scanning calorimetry(DSC),compression tests and transmission electron microscopy(TEM).When cooling the alloy specimen from high temperature to room temperature,β(parent phase)→β’(interphase)→β″(martensite) two step phase transformation occurs.The microstructure at room temperature shows regularly arranged band morphology with the monoclinic crystal structure.The twinning relationship between the martensite bands was determined to be(101) Type I.Reorientation and of the martensite bands inside the variant and dislocation were found during compression at room temperature.The maximum complete recovery strain is about 1.5%.

MICROSTRUCTURE AND REVERSE SHAPE MEMORY EFFECT IN A Cu-Zn-Al ALLOY

The bainite structure in a Cu-Zn-A1 alloy related to the reverse shape memory effect has been observed by means of TEM.The reverse memory effect may be improved by up to one order of magnitude under applied constraint stress.The widespread propagation of bainite was confirmed to be the diffusion controlled shear process by the parabolic configuration of side interface of bainite plate and the twisting of intersected bainite plates.

Martensite Aging Effect and Thermal Cyclic Characteristics in Ti-Pd and Ti-Pd-Ni High Temperature Shape Memory Alloys

The effect of thermal cycling and aging in martensitic state in Ti-Pd-Ni alloys were investigated by DSC and TEM observations. It is shown that the thermal cycling causes the decreases in M, and Af temperatures in Ti50Pd50-xNix (x=10, 20, 30) alloys, but no obvious thermal cycling effect was observed in Ti50Pd50Pd40Ni10 alloys and the aging effect shows a curious feature, i.e., the Af temperature does not saturate even after relatively long time aging, which is considered to be due to the occurrence of recovery recrystallization during aging.