Strain-rate frequency superposition(SRFS) is often employed to probe the low-frequency behavior of soft solids under oscillatory shear in anticipated linear response. However, physical interpretation of an apparently ...Strain-rate frequency superposition(SRFS) is often employed to probe the low-frequency behavior of soft solids under oscillatory shear in anticipated linear response. However, physical interpretation of an apparently well-overlapped master curve generated by SRFS has to combine with nonlinear analysis techniques such as Fourier transform rheology and stress decomposition method. The benefit of SRFS is discarded when some inconsistencies of the shifted master curves with the canonical linear response are observed. In this work, instead of evaluating the SRFS in full master curves, two criteria were proposed to decompose the original SRFS data and to delete the bad experimental data. Application to Carabopol suspensions indicates that good master curves could be constructed based upon the modified data and the high-frequency deviations often observed in original SRFS master curves are eliminated. The modified SRFS data also enable a better quantitative description and the evaluation of the apparent structural relaxation time by the two-mode fractional Maxwell model.展开更多
The microstructure of x-Ti/ mild steel composite fabricated by using constant stand-off cladding technique was observed with optical microscopy, SEM and TEM analyses. Very fine equiaxed grains (<0.1um) with a low d...The microstructure of x-Ti/ mild steel composite fabricated by using constant stand-off cladding technique was observed with optical microscopy, SEM and TEM analyses. Very fine equiaxed grains (<0.1um) with a low dislocation density were observed in the adiabatic shear bands (ASB) this enables a thermomechanical response that may lead to a super plastic de formation.展开更多
Distribution of localized damage in shear band can’ t be predicted theoretically based on classical elastoplastic theory. The average damage variable in shear band was considered to be a non-local variable. Based on ...Distribution of localized damage in shear band can’ t be predicted theoretically based on classical elastoplastic theory. The average damage variable in shear band was considered to be a non-local variable. Based on non-local theory, an analytical expression for the localized damage in strain-softening region of shear band in the process of shear band propagation was presented using boundary condition and symmetry of local damage variable, etc. The results show that dynamic shear softening modulus, dynamic shear strength and shear elastic modulus influence the distribution of the localized damage in shear band. Internal length of ductile metal only governs the thickness of shear band. In the strain-softening region of shear band, the local damage variable along shear band’s tangential and normal directions is non-linear and highly non-uniform. The non-uniformities in the normal and tangential directions of shear band stem from the interactions and interplaying among microstructures and the non-uniform distribution of shear stress, respectively. At the tail of the strain-softening region, the maximum value of local damage variable reaches 1. This means that material at this position fractures completely. At the tip of shear band and upper as well as lower boundaries, no damage occurs. Local damage variable increases as dynamic shear softening modulus decreases or shear elastic modulus increases, leading to difficulty in identification or detection of damage for less ductile metal material at higher strain rates.展开更多
By using MTS815 rock mechanics test system,a series of acoustic emission(AE) location experiments were performed under unloading confining pressure,increasing the axial stress.The AE space-time evolution regularities ...By using MTS815 rock mechanics test system,a series of acoustic emission(AE) location experiments were performed under unloading confining pressure,increasing the axial stress.The AE space-time evolution regularities and energy releasing characteristics during deformation and failure process of coal of different loading rates are compared,the influence mechanism of loading rates on the microscopic crack evolution were studied,combining the AE characteristics and the macroscopic failure modes of the specimens,and the precursory characteristics of coal failure were also analyzed quantitatively.The results indicate that as the loading rate is higher,the AE activity and the main fracture will begin earlier.The destruction of coal body is mainly the function of shear strain at lower loading rate and tension strain at higher rate,and will transform from brittleness to ductility at critical velocities.When the deformation of the coal is mainly plasticity,the amplitude of the AE ringing counting rate increases largely and the AE energy curves appear an obvious ''step'',which can be defined as the first failure precursor point.Statics of AE information shows that the strongest AE activity begins when the axial stress level was 92-98%,which can be defined as the other failure precursor point.As the loading rate is smaller,the coal more easily reaches the latter precursor point after the first one,so attention should be aroused to prevent dynamic disaster in coal mining when the AE activity reaches the first precursor point.展开更多
The dynamic shear strength of rocks is required for the earthquake-resistant design of nuclear power plants in Japan.This research aims to propose a mathematical model for estimating the dynamic strength and to valida...The dynamic shear strength of rocks is required for the earthquake-resistant design of nuclear power plants in Japan.This research aims to propose a mathematical model for estimating the dynamic strength and to validate the model.Two different types of specimens were prepared for the model validation,and the monotonic and cyclic loading tests were conducted to obtain the mathematical model parameters.Subsequently,multistep cyclic loading tests were performed,followed by simulations using the mathematical model.The test results demonstrated that the dynamic shear strength exceeded the static shear strength,which agreed with previous researches.Furthermore,the dynamic shear strength calculated using the mathematical model was generally consistent with that obtained from the experimental data.展开更多
The upper crustal anisotropy of Yunnan area, SE margin of Tibetan Plateau, is investigated by measuring the shear wave splitting of local earthquakes. The mean value of the measured delay times is 0.054 s and far less...The upper crustal anisotropy of Yunnan area, SE margin of Tibetan Plateau, is investigated by measuring the shear wave splitting of local earthquakes. The mean value of the measured delay times is 0.054 s and far less than that from Pms splitting analysis, indicating that the crustal anisotropy is contributed mostly from mid-lower crust. The fast polarization directions are mostly sub-parallel to the maximum horizontal compression directions while the stations near fault zones show fault-parallel fast polarization directions, suggesting both stress and geological structure contribute to the upper crust anisotropy.Comparing fast polarization directions from shear wave splitting of local earthquakes and Pms, large angle differences are shown at most stations, implying different anisotropy properties between upper and mid-lower crust. However, in southwestern Yunnan, the fast polarization directions of Pms and Swave splitting are nearly parallel, and the stress and surface strain rate directions show strong correlation, which may indicate that the surface and deep crust deformations can be explained by the same mechanism and the surface deformation can represent the deformation of the whole crust. Therefore,the high correlation between surface strain and mantle deformation in this area suggests the mechanical coupling between crust and mantle in southwestern Yunnan. In the rest region of Yunnan, the crustmantle coupling mechanisms are supported by the lack of significant crustal anisotropy with Ne S fast polarization directions from Pms splitting. Therefore, we conclude that the crust and upper mantle are coupled in Yunnan, SE margin of Tibetan Plateau.展开更多
Based on the multiple-term horizontal velocity solutions of 230 GPS monitoring sites in Tianshan and its adjacent region, the GPS site velocity fields and crustal horizontal strain fields in the area have been obtaine...Based on the multiple-term horizontal velocity solutions of 230 GPS monitoring sites in Tianshan and its adjacent region, the GPS site velocity fields and crustal horizontal strain fields in the area have been obtained. The results show that the crustal shortening rate of Tianshan, with the longitude (77°±1°)E as the boundary, gradually decreased towards two sides, from the south to the north, indicating that the pushing force of plate becomes weaker along with the fold deformation decreasing of the Tianshan. The direction of principal compressive strain of Tianshan and its adjacent area, nearly NNW, is basically perpendicular to the Tianshan cordillera trend, suggesting the distribution and variation of maximum principal compressive stress in Tianshan and its adjacent region resulted from collision and extrusion of Indian Plate. This paper indicates that the maximum shear strain field mainly con- centrates on two areas, one is Isyk lake of North Tianshan, Kyrgyzstan, and the other is the juncture of Jiashi (South Tianshan) and Pamir arc faults. In the above areas, it can be shown from the epicentral distribution that the strong earthquakes mostly occurs at the high shearing strain accumulation filed or its edge.展开更多
Adiabatic shear behavior and the corresponding mechanism of TiB2/Al composites were researched by split Hopkinson pressure bar (SHPB).Results show that the flow stresses of the TiB2/Al composites exhibit softening t...Adiabatic shear behavior and the corresponding mechanism of TiB2/Al composites were researched by split Hopkinson pressure bar (SHPB).Results show that the flow stresses of the TiB2/Al composites exhibit softening tendency with the increasing of strain rates. All the composites fail in splitting and cutting with a 45 degree, and the phase transformed bands of molten aluminum are found on the adiabatic shear layers. The deformation behavior and shear localization of the TiB2/Al composites specimens were simulated by finite element code MSC.Marc. The Johnson-Cook model was used to describe the thermo-viscoplastic response of the specimen material. There was unanimous between the numerical result and the experimental result on the location of the adiabatic shear band. From the numerical simulation and experiment, it was concluded that the instantaneous failure of the composite was ascribed due to the local low strength area where the formation of adiabatic shear band was, and the stress condition had significant effect on the initiation and propagation of adiabatic shear band (ASB).展开更多
An investigation has been made into the microstructural characterization of the shear bands generated under high-strain rate (≈10^4 s^-1) deformation in Fe-15%Cr-15%Ni single crystal by EBSD-SEM (electron backscat...An investigation has been made into the microstructural characterization of the shear bands generated under high-strain rate (≈10^4 s^-1) deformation in Fe-15%Cr-15%Ni single crystal by EBSD-SEM (electron backscatter diffraction-scanning electron microscopy), TEM (transmission electron in microscopy) and HREM (high- resolution electron microscopy). The results reveal that the propagation of the shear band exhibits an asymmetrical behavior arising from inhomogenous distribution in plasticity in the bands because of different resistance to the collapse in different crystallographic directions; The γ-ε-α′phase transformations may take place inside and outside the bands, and these martensitic phases currently nucleate at intersections either between the twins and deformation bands or between the twins and ε-sheet. Investigation by EBSD shows that recrystallization can occur in the bands with a grain size of an average of 0.2μm in diameter. These nano-grains are proposed to attribute to the results of either dynamic or static recrystallization, which can be described by the rotational recrystallization mechanism. Calculation and analysis indicate that the strain rate inside the shear band can reach 2.50×10^6 s^-1, which is higher, by two or three orders of magnitude, than that exerted dynamically on the specimen tested.展开更多
基金Project(11372263)supported by the National Natural Science Foundation of China
文摘Strain-rate frequency superposition(SRFS) is often employed to probe the low-frequency behavior of soft solids under oscillatory shear in anticipated linear response. However, physical interpretation of an apparently well-overlapped master curve generated by SRFS has to combine with nonlinear analysis techniques such as Fourier transform rheology and stress decomposition method. The benefit of SRFS is discarded when some inconsistencies of the shifted master curves with the canonical linear response are observed. In this work, instead of evaluating the SRFS in full master curves, two criteria were proposed to decompose the original SRFS data and to delete the bad experimental data. Application to Carabopol suspensions indicates that good master curves could be constructed based upon the modified data and the high-frequency deviations often observed in original SRFS master curves are eliminated. The modified SRFS data also enable a better quantitative description and the evaluation of the apparent structural relaxation time by the two-mode fractional Maxwell model.
文摘The microstructure of x-Ti/ mild steel composite fabricated by using constant stand-off cladding technique was observed with optical microscopy, SEM and TEM analyses. Very fine equiaxed grains (<0.1um) with a low dislocation density were observed in the adiabatic shear bands (ASB) this enables a thermomechanical response that may lead to a super plastic de formation.
基金Project(2004F052) supported by the Educational Department of Liaoning Province, China
文摘Distribution of localized damage in shear band can’ t be predicted theoretically based on classical elastoplastic theory. The average damage variable in shear band was considered to be a non-local variable. Based on non-local theory, an analytical expression for the localized damage in strain-softening region of shear band in the process of shear band propagation was presented using boundary condition and symmetry of local damage variable, etc. The results show that dynamic shear softening modulus, dynamic shear strength and shear elastic modulus influence the distribution of the localized damage in shear band. Internal length of ductile metal only governs the thickness of shear band. In the strain-softening region of shear band, the local damage variable along shear band’s tangential and normal directions is non-linear and highly non-uniform. The non-uniformities in the normal and tangential directions of shear band stem from the interactions and interplaying among microstructures and the non-uniform distribution of shear stress, respectively. At the tail of the strain-softening region, the maximum value of local damage variable reaches 1. This means that material at this position fractures completely. At the tip of shear band and upper as well as lower boundaries, no damage occurs. Local damage variable increases as dynamic shear softening modulus decreases or shear elastic modulus increases, leading to difficulty in identification or detection of damage for less ductile metal material at higher strain rates.
文摘By using MTS815 rock mechanics test system,a series of acoustic emission(AE) location experiments were performed under unloading confining pressure,increasing the axial stress.The AE space-time evolution regularities and energy releasing characteristics during deformation and failure process of coal of different loading rates are compared,the influence mechanism of loading rates on the microscopic crack evolution were studied,combining the AE characteristics and the macroscopic failure modes of the specimens,and the precursory characteristics of coal failure were also analyzed quantitatively.The results indicate that as the loading rate is higher,the AE activity and the main fracture will begin earlier.The destruction of coal body is mainly the function of shear strain at lower loading rate and tension strain at higher rate,and will transform from brittleness to ductility at critical velocities.When the deformation of the coal is mainly plasticity,the amplitude of the AE ringing counting rate increases largely and the AE energy curves appear an obvious ''step'',which can be defined as the first failure precursor point.Statics of AE information shows that the strongest AE activity begins when the axial stress level was 92-98%,which can be defined as the other failure precursor point.As the loading rate is smaller,the coal more easily reaches the latter precursor point after the first one,so attention should be aroused to prevent dynamic disaster in coal mining when the AE activity reaches the first precursor point.
文摘The dynamic shear strength of rocks is required for the earthquake-resistant design of nuclear power plants in Japan.This research aims to propose a mathematical model for estimating the dynamic strength and to validate the model.Two different types of specimens were prepared for the model validation,and the monotonic and cyclic loading tests were conducted to obtain the mathematical model parameters.Subsequently,multistep cyclic loading tests were performed,followed by simulations using the mathematical model.The test results demonstrated that the dynamic shear strength exceeded the static shear strength,which agreed with previous researches.Furthermore,the dynamic shear strength calculated using the mathematical model was generally consistent with that obtained from the experimental data.
基金supported by the National 973 Project of China (No.2013CB733303)the open fund of Key Laboratory of Geospace Environment and Geodesy,Ministry of Education (No.15-02-07)
文摘The upper crustal anisotropy of Yunnan area, SE margin of Tibetan Plateau, is investigated by measuring the shear wave splitting of local earthquakes. The mean value of the measured delay times is 0.054 s and far less than that from Pms splitting analysis, indicating that the crustal anisotropy is contributed mostly from mid-lower crust. The fast polarization directions are mostly sub-parallel to the maximum horizontal compression directions while the stations near fault zones show fault-parallel fast polarization directions, suggesting both stress and geological structure contribute to the upper crust anisotropy.Comparing fast polarization directions from shear wave splitting of local earthquakes and Pms, large angle differences are shown at most stations, implying different anisotropy properties between upper and mid-lower crust. However, in southwestern Yunnan, the fast polarization directions of Pms and Swave splitting are nearly parallel, and the stress and surface strain rate directions show strong correlation, which may indicate that the surface and deep crust deformations can be explained by the same mechanism and the surface deformation can represent the deformation of the whole crust. Therefore,the high correlation between surface strain and mantle deformation in this area suggests the mechanical coupling between crust and mantle in southwestern Yunnan. In the rest region of Yunnan, the crustmantle coupling mechanisms are supported by the lack of significant crustal anisotropy with Ne S fast polarization directions from Pms splitting. Therefore, we conclude that the crust and upper mantle are coupled in Yunnan, SE margin of Tibetan Plateau.
基金National Natural Science Foundation of China (40074024) and Natural Science Foundation of Xinjiang Uygur Autonomous Region (200321101).
文摘Based on the multiple-term horizontal velocity solutions of 230 GPS monitoring sites in Tianshan and its adjacent region, the GPS site velocity fields and crustal horizontal strain fields in the area have been obtained. The results show that the crustal shortening rate of Tianshan, with the longitude (77°±1°)E as the boundary, gradually decreased towards two sides, from the south to the north, indicating that the pushing force of plate becomes weaker along with the fold deformation decreasing of the Tianshan. The direction of principal compressive strain of Tianshan and its adjacent area, nearly NNW, is basically perpendicular to the Tianshan cordillera trend, suggesting the distribution and variation of maximum principal compressive stress in Tianshan and its adjacent region resulted from collision and extrusion of Indian Plate. This paper indicates that the maximum shear strain field mainly con- centrates on two areas, one is Isyk lake of North Tianshan, Kyrgyzstan, and the other is the juncture of Jiashi (South Tianshan) and Pamir arc faults. In the above areas, it can be shown from the epicentral distribution that the strong earthquakes mostly occurs at the high shearing strain accumulation filed or its edge.
基金the National Engineering Research Center Open Fund(No.2011007B)Natural Science Foundation of GuangDong Province(No.10451064101004631)
文摘Adiabatic shear behavior and the corresponding mechanism of TiB2/Al composites were researched by split Hopkinson pressure bar (SHPB).Results show that the flow stresses of the TiB2/Al composites exhibit softening tendency with the increasing of strain rates. All the composites fail in splitting and cutting with a 45 degree, and the phase transformed bands of molten aluminum are found on the adiabatic shear layers. The deformation behavior and shear localization of the TiB2/Al composites specimens were simulated by finite element code MSC.Marc. The Johnson-Cook model was used to describe the thermo-viscoplastic response of the specimen material. There was unanimous between the numerical result and the experimental result on the location of the adiabatic shear band. From the numerical simulation and experiment, it was concluded that the instantaneous failure of the composite was ascribed due to the local low strength area where the formation of adiabatic shear band was, and the stress condition had significant effect on the initiation and propagation of adiabatic shear band (ASB).
文摘An investigation has been made into the microstructural characterization of the shear bands generated under high-strain rate (≈10^4 s^-1) deformation in Fe-15%Cr-15%Ni single crystal by EBSD-SEM (electron backscatter diffraction-scanning electron microscopy), TEM (transmission electron in microscopy) and HREM (high- resolution electron microscopy). The results reveal that the propagation of the shear band exhibits an asymmetrical behavior arising from inhomogenous distribution in plasticity in the bands because of different resistance to the collapse in different crystallographic directions; The γ-ε-α′phase transformations may take place inside and outside the bands, and these martensitic phases currently nucleate at intersections either between the twins and deformation bands or between the twins and ε-sheet. Investigation by EBSD shows that recrystallization can occur in the bands with a grain size of an average of 0.2μm in diameter. These nano-grains are proposed to attribute to the results of either dynamic or static recrystallization, which can be described by the rotational recrystallization mechanism. Calculation and analysis indicate that the strain rate inside the shear band can reach 2.50×10^6 s^-1, which is higher, by two or three orders of magnitude, than that exerted dynamically on the specimen tested.
基金supported by the National Natural Science Foundation of China(Nos.11872317,11972310)the Project of Key Laboratory of Impact and Safety Engineering(Ningbo University),Ministry of Education,China(No.CJ202208)Science Challenge Project,China(No.TZ2018001)。