Mathematical Model and Experiment Validation of Fluid Torque by Shear Stress under Influence of Fluid Temperature in Hydro-viscous Clutch

The current design of hydro-viscous clutch（HVC） in tracked vehicle fan transmission mainly focuses on high-speed and high power. However, the fluid torque under the influence of fluid temperature can not be predicted accurately by conventional mathematical model or experimental research. In order to validate the fluid torque of HVC by taking the viscosity-temperature characteristic of fluid into account, the test rig is designed. The outlet oil temperature is measured and fitted with different rotation speed, oil film thickness, oil flow rate, and inlet oil temperature. Meanwhile, the film torque can be obtained. Based on Navier-Stokes equations and the continuity equation, the mathematical model of fluid torque is proposed in cylindrical coordinate. Iterative method is employed to solve the equations. The radial and tangential speed distribution, radial pressure distribution and theoretical flow rate are determined and analyzed. The models of equivalent radius and fluid torque of friction pairs are introduced. The experimental and theoretical results indicate that tangential speed distribution is mainly determined by the relative rotating speed between the friction plate and the separator disc. However, the radial speed distribution and pressure distribution are dominated by pressure difference at the lower rotating speed. The oil film fills the clearance and the film torque increases with increasing rotating speed. However, when the speed reaches a certain value, the centrifugal force will play an important role on the fluid distribution. The pressure is negative at the outer radius when inlet flow rate is less than theoretical flow, so the film starts to shrink which decreases the film torque sharply. The theoretical fluid torque has good agreement with the experimental data. This research proposes a new fluid torque mathematical model which may predict the film torque under the influence of temperature more accurately.

Dynamic modeling and control of extracellular ATP concentration on vascular endothelial cells via shear stress modulation

A new dynamic model for cell-deformation-induced adenosine triphosphate （ATP） release from vascular endothelial cells （VECs） is proposed in this paper to quantify the relationship between the ATP concentration at the surface of VECs and blood flow-induced shear stress. The simulation results demonstrate that ATP concentration at the surface of VECs predicted by the proposed new dynamic model is more consistent with the experimental observations than those by the existing static and dynamic models. Furthermore, it is the first time that a proportional-integral-derivative （PID） feedback controller is applied to modulate extracellular ATP concentration. Three types of desired ATP concentration profiles including constant, square wave and sinusoid are obtained by regulating the wall shear stress under this PID control. The systematic methodology utilized in this paper to model and control ATP release from VECs via adjusting external stimulus opens up a new scenario where quantitative investigations into the underlying mechanisms for many biochemical phenomena can be carded out for the sake of controlling specific cellular events.

An Application of the Modified Shear Lag Model to Study the Influence of Thermal Residual Stresses on the Stiffness and Yield Strength of Short Fiber Reinforced Metal Matrix Composites

The modified shear lag model proposed recently was applied to calculate thermal residual stresses and subsequent stress distributions under tensile and compressive loadings. The expressions for the elastic moduli and the yield strengths under tensile and compressive loadings were derived which take account of thermal residual stresses. The asymmetries in the elastic modulus and the yield strength were interpreted using the derived expressions and the obtained results of the stress calculations. The model predictions have exhibited good agreements with the experimental results and also with the other theoretical predictions

A New Modified Conductivity Model for Prediction of Shear Yield Stress of Electrorheological Fluids Based on Face-center Square Structure

A new modified conductivity model was established to predict the shear yield stress of electrorheological fluids (ERF). By using a cell equivalent method, the present model can deal with the face-center square structure of ERF. Combining the scheme of the classical conductivity model for the single-chain structure, a new formula for the prediction of the shear yield stress of ERF was set up. The influences of the separation distance of the particles, the volume fraction of the particles and the applied electric field on the shear yield stress were investigated.

A mathematical model for ATP-mediated calcium dynamics in vascular endothelial cells induced by fluid shear stress

In consideration of the mechanism for shear-stress-induced Ca^2＋ influx via ATP（adenosine triphosphate）-gated ion channel P2X4 in vascular endothelial cells, a modified model is proposed to describe the shear-stress-induced Ca^2＋ influx. It is affected both by the Ca^2＋ gradient across the cell membrane and extracellular ATP concentration on the cell surface. Meanwhile, a new static ATP release model is constructed by using published experimental data. Combining the modified intracellular calcium dynamics model with the new ATP release model, we establish a nonlinear Ca^2＋ dynamic system in vascular endothelial cells. The ATP-mediated calcium response in vascular endothelial cells subjected to shear stresses is analyzed by solving the governing equations of the integrated dynamic system. Numerical results show that the shear-stress-induced calcium response predicted by the proposed model is more consistent with the experimental observations than that predicted by existing models.

Mathematical Modeling of Shear Stress and Direct Shear Test for Compressible Soil: Case of Soil Bordering the Wouri River

This paper focuses on the development of the mathematical model of shear stress by direct shear test for compressible soil of the littoral region, which will be a great tool in the hand of geotechnical engineers. The most common use of a shear test is to determine the shear strength which is the maximum shear stress that a material can withstand before the failure occurs. This parameter is useful in many engineering designs such as foundations, roads and retaining walls. We carried out an experimental laboratory test of ten samples of undisturbed soil taken at different points of the border of Wouri river of Cameroon. The samples were collected at different depths and a direct shear test was conducted. The investigations have been performed under constant vertical stresses and constant sample volume with the aim to determine the frictional angle and the cohesion of the compressible soil which are so important to establish the conditions of buildings stability. Special care was taken to derive loading conditions actually existing in the ground and to duplicate them in the laboratory. Given that the buildings constructed in this area are subjected to settlement, landslide, and punch break or shear failure, the cohesion and the frictional angle are determined through the rupture line after assessed the mean values of the shear stress for the considered ten samples. The bearing capacity of the soil, which is the fundamental soil parameter, was calculated. From the laboratory experimental results, the least squared method was used to derive an approximated mathematical model of the shearing stress. Many optimizations methods were then considered to reach the best adjustment.

Experimental Research on Boundary Shear Stress in Typical Meandering Channel

A novel instrument named Micro-Electro-Mechanical System(MEMS) flexible hot-film shear stress sensor was used to study the boundary shear stress distribution in the generalized natural meandering open channel, and the mean sidewall shear stress distribution along the meandering channel, and the lateral boundary shear stress distribution in the typical cross-section of the meandering channel was analysed. Based on the measurement of the boundary shear stress, a semi-empirical semi-theoretical computing approach of the boundary shear stress was derived including the effects of the secondary flow, sidewall roughness factor, eddy viscosity and the additional Reynolds stress, and more importantly, for the first time, it combined the effects of the cross-section central angle and the Reynolds number into the expressions. Afterwards, a comparison between the previous research and this study was developed. Following the result, we found that the semi-empirical semi-theoretical boundary shear stress distribution algorithm can predict the boundary shear stress distribution precisely. Finally, a single factor analysis was conducted on the relationship between the average sidewall shear stress on the convex and concave bank and the flow rate, water depth, slope ratio,or the cross-section central angle of the open channel bend. The functional relationship with each of the above factors was established, and then the distance from the location of the extreme sidewall shear stress to the bottom of the open channel was deduced based on the statistical theory.

STEADY-SHEAR VISCOSITY AND TRANSIENT STRESS RESPONSE FOR ELASTO-THIXOTROPIC FLUIDS

A phenomenological model for dispersed systems which exhibit complex theological behaviour such as shear and time-dependent viscosity, yield stress, and elasticity is proposed. The model extends the Quemeda model to describe the viscosity function with a structural parameter λ which varies according to differ- ent kinetic orders of particle aggregation and segregation. The transient stress response is obtained by solving an instantaneous Maxwell model with an assumed shear modulus function G of the same form as the viscosity function η. Accuracy of the proposed model is verified experimentally with the results obtained for two oil (creosote)/water emulsions. The model that gives the best fit of experimental data appears to be the one with kinetic orders n = m = 2.

Wall shear stress in intracranial aneurysms and adjacent arteries

Hemodynamic parameters play an important role in aneurysm formation and growth. However, it is difficult to directly observe a rapidly growing de novo aneurysm in a patient. To investigate possible associations between hemodynamic parameters and the formation and growth of intracranial aneurysms, the present study constructed a computational model of a case with an internal carotid artery aneurysm and an anterior communicating artery aneurysm, based on the CT angiography findings of a patient. To simulate the formation of the anterior communicating artery aneurysm and the growth of the internal carotid artery aneurysm, we then constructed a model that virtually removed the anterior communicating artery aneurysm, and a further two models that also progressively decreased the size of the internal carotid artery aneurysm. Computational simulations of the fluid dynamics of the four models were performed under pulsatile flow conditions, and wall shear stress was compared among the different models. In the three aneurysm growth models, increasing size of the aneurysm was associated with an increased area of low wall shear stress, a significant decrease in wall shear stress at the dome of the aneurysm, and a significant change in the wall shear stress of the parent artery. The wall shear stress of the anterior communicating artery remained low, and was significantly lower than the wall shear stress at the bifurcation of the internal carotid artery or the bifurcation of the middle cerebral artery. After formation of the anterior communicating artery aneurysm, the wall shear stress at the dome of the internal carotid artery aneurysm increased significantly, and the wall shear stress in the upstream arteries also changed significantly. These findings indicate that low wall shear stress may be associated with the initiation and growth of aneurysms, and that aneurysm formation and growth may influence hemodynamic parameters in the local and adjacent arteries.

Calibration and validation of a sand model considering the effects of wave-induced principal stress axes rotation

Principal stress axes rotation influences the stress-strain behavior of sand under wave loading. A constitutive model for sand, which considers principal stress orientation and is based on generalized plasticity theory, is proposed. The new model, which employs stress invariants and a discrete memory factor during reloading, is original because it quantifies model parameters using experimental data. Four sets of hollow torsion experiments were conducted to calibrate the parameters and predict the capability of the proposed model, which describes the effects of principal stress orientation on the behavior of sand. The results prove the effectiveness of the proposed calibration method.

Application of the Mechanical Threshold Stress Model to Large Strain Processing

Large-strain deformations introduce several confounding factors that affect the application of the Mechanical Threshold Stress model. These include the decrease with the increasing stress of the normalized activation energy characterizing deformation kinetics, the tendency toward Stage IV hardening at high strains, and the influence of crystallographic texture. Minor additions to the Mechanical Threshold Stress model are introduced to account for variations of the activation energy and the addition of Stage IV hardening. Crystallographic texture cannot be modeled using an isotropic formulation, but some common trends when analyzing predominantly shear deformation followed by uniaxial deformation are described. Comparisons of model predictions with measurements in copper processed using Equal Channel Angular Pressing are described.

Principle of Interaction between Plastic Volumetric and Shear Strains and the Constitutive Model for Geotechnical Materials

Here is proposed the principle of interaction between plastic volumetric and shear strains, revealing the main origin of generating the complexity and variety of deformations for geotechnical materials. Here are also explained the manners of the interaction between plastic volumetric and shear strains and the conditions of generating shear dilatancy. It is demonstrated that dependency of the stress path exists and is a combination of effects of this interaction. According to this principle, it is theoretically proved that the space critical state line exists, and is unique and independent of the stress history. Based on this principle, the constitutive models that are able completely and accurately to characterize the basic behavior features for geotechnical materials have been constructed within the framework of thermodynamics. What is determined is a general expression of the constitutive relation as well as the inequality of the dissipative potential increment for obeying the second law of thermodynamics.

Quantitative calculation of local shear deformation in adiabatic shear band for Ti-6Al-4V

JOHNSON-COOK(J-C) model was used to calculate flow shear stress—shear strain curve for Ti-6Al-4V in dynamic torsion test. The predicted curve was compared with experimental result. Gradient-dependent plasticity(GDP) was introduced into J-C model and GDP was involved in the measured flow shear stress—shear strain curve, respectively, to calculate the distribution of local total shear deformation(LTSD) in adiabatic shear band(ASB). The predicted LTSDs at different flow shear stresses were compared with experimental measurements. J-C model can well predict the flow shear stress—shear strain curve in strain-hardening stage and in strain-softening stage where flow shear stress slowly decreases. Beyond the occurrence of ASB, with a decrease of flow shear stress, the increase of local plastic shear deformation in ASB is faster than the decrease of elastic shear deformation, leading to more and more apparent shear localization. According to the measured flow shear stress—shear strain curve and GDP, the calculated LTSDs in ASB are lower than experimental results. At earlier stage of ASB, though J-C model overestimates the flow shear stress at the same shear strain, the model can reasonably assess the LTSDs in ASB. According to the measured flow shear stress—shear strain curve and GDP, the calculated local plastic shear strains in ASB agree with experimental results except for the vicinity of shear fracture surface. In the strain-softening stage where flow shear stress sharply decreases, J-C model cannot be used. When flow shear stress decreases to a certain value, shear fracture takes place so that GDP cannot be used.

Shear strength criteria for rock,rock joints,rockfill and rock masses:Problems and some solutions

Although many intact rock types can be very strong,a critical confining pressure can eventually be reached in triaxial testing,such that the Mohr shear strength envelope becomes horizontal.This critical state has recently been better defined,and correct curvature or correct deviation from linear Mohr-Coulomb（MC） has finally been found.Standard shear testing procedures for rock joints,using multiple testing of the same sample,in case of insufficient samples,can be shown to exaggerate apparent cohesion.Even rough joints do not have any cohesion,but instead have very high friction angles at low stress,due to strong dilation.Rock masses,implying problems of large-scale interaction with engineering structures,may have both cohesive and frictional strength components.However,it is not correct to add these,following linear M-C or nonlinear Hoek-Brown（H-B） standard routines.Cohesion is broken at small strain,while friction is mobilized at larger strain and remains to the end of the shear deformation.The criterion ＇c then σn tan φ＇ should replace ＇c plus σn tan φ＇ for improved fit to reality.Transformation of principal stresses to a shear plane seems to ignore mobilized dilation,and caused great experimental difficulties until understood.There seems to be plenty of room for continued research,so that errors of judgement of the last 50 years can be corrected.

Analytical Higher-Order Model for Flexible and Stretchable Sensors

The stretchable sensor wrapped around a foldable airfoil or embedded inside of it has great potential for use in the monitoring of the structural status of the foldable airfoil.The design methodology is important to the development of the stretchable sensor for status monitoring on the foldable airfoil.According to the requirement of mechanical flexibility of the sensor,the combined use of a layered flexible structural formation and a strain isolation layer is implemented.An analytical higher-order model is proposed to predict the stresses of the strain-isolation layer based on the shear-lag model for the safe design of the flexible and stretchable sensors.The normal stress and shear stress equations in the constructed structure of the sensors are obtained by the proposed model.The stress distribution in the structure is investigated when bending load is applied to the structures.The numerical results show that the proposed model can predict the variation of normal stress and shear stress along the thickness of the strain-isolation（polydimethylsiloxane）layer accurately.The results by the proposed model are in good agreement with the finite element method,in which the normal stress is variable while the shear stress is invariable along the thickness direction of strain-isolation layer.The high-order model is proposed to predict the stresses of the layered structure of the flexible and stretchable sensor for monitoring the status of the foldable airfoil.

An interfacial mechanical model for the analysis of earthquake

In this paper, the shear beam model for analysis of interface failure under joint action of anti-plane shearing and lateral compression and its principal behavior were briefly introduced. The calculation of energy release that is related to the strength of earthquake was presented by using the shear beam model. The sudden increase of load resulted from the 'stress locking' at the interface layer in the reloading process was investigated. At the end of the paper, discussions on the mechanism of earthquake were given out.

Pore water pressure increment model for saturated Nanjing fine sand subject to cyclic loading

Three groups of dynamic triaxial tests were performed for saturated Nanjing fine sand subjected to uniform cyclic loading. The tested curves of the excess pore water pressure （EPWP） ratio variation with the ratio of the number of cycles are provided. The concept of the EPWP increment ratio is introduced and two new concepts of the effective dynamic shear stress ratio and the log decrement of effective stress are defined. It is found that the development of the EPWP increment ratio can be divided into three stages： descending, stable and ascending. Furthermore, at the stable and ascending stages, a satisfactory linear relationship is obtained between the accumulative EPWP increment ratio and natural logarithm of the effective dynamic shear stress ratio. Accordingly, the EPWP increment ratio at the number of cycles N has been deduced that is proportional to the log decrement of effective stress at the cycle number N-l, but is independent of the cyclic stress amplitude. Based on the analysis, a new EPWP increment model for saturated Nanjing fine sand is developed from tested data fitting, which provides a better prediction of the curves of EPWP generation, the number of cycles required for initial liquefaction and the liquefaction resistance.

锚杆岩体界面载荷传递规律及锚固长度设计

为揭示巷道围岩锚固界面脱粘失效机理,量化锚杆支护设计参数,采用三线性粘结滑移模型进行理论分析,对轴向载荷作用下锚固脱粘失效全过程中,锚固段界面剪应力、锚杆轴力分布演化规律以及界面极限锚固力进行研究,根据锚固段长度不同,得到两种界面剪应力分布演化类型。研究结果表明:当锚固长度较短时,界面剪应力存在全长软化阶段;当锚固长度较长时,界面剪应力存在弹性-软化-滑移三段共存阶段。锚固粘结界面弹性段、软化段、摩擦段内的剪应力分别呈现双曲余弦函数衰减分布、余弦函数上升分布、均匀分布规律,锚杆轴力随界面剪应力分布演化呈现多种形态的衰减分布规律。根据锚固界面模型解析计算获得极限锚固力,当不考虑脱粘摩擦力时,极限锚固力随锚固长度的增加趋近于某一固定值;当考虑脱粘摩擦力时,增加锚固长度能够持续提高锚固界面安全系数。研究成果可为锚固机制分析、锚杆支护参数设计提供理论参考。

盾构壁后注浆窜浆模型试验及发生条件研究

全断面围岩管片壁后注浆因向开挖面方向的窜浆现象会引起盾尾空隙注浆不饱满,管片上浮、错台及开裂,螺机喷涌等事故常有发生,已经引起广泛重视。通过设计自制壁后注浆液窜浆模型装置进行试验,分析浆液性质、缝隙厚度、注浆压力差对是否发生窜浆及窜浆量的影响,并探讨了不发生窜浆的临界条件。结果表明:(1)浆液压力与窜浆距离呈线性衰减,当浆液稠度较低时,窜浆量与缝隙厚度、浆液稠度呈近似线性正相关、与浆液的剪切屈服应力呈近似线性负相关,窜浆距离与注浆压力差呈近似线性正相关;当浆液稠度增大时,以上关系将逐渐转化为非线性关系;(2)通过极差分析表明浆液的窜浆量受盾壳与岩层间缝隙厚度影响最大,注浆压力与开挖面压力差影响其次,最后是浆液本身的性质;(3)建立了窜浆临界分析模型和计算公式,得到了窜浆发生条件和判别方法,可用于指导稳定围岩地层中盾构掘进时浆液的配制。

Dynamic constitutive model for soils considering asymmetry of skeleton curve

Based on the asymmetric characteristic of skeleton curve obtained from dynamic tests on soils,a function with double asymptotes is proposed for describing the dynamic constitutive relations of soils.The hysteresis loops observed during unloading and reloading show the same form as the skeleton curve and are constructed by taking the ultimate stress as the corresponding asymptote.The coeffcient of initial unloading modulus is used to ensure that the constructed hysteresis loop fts well with the experimental data.Then,a new dynamic constitutive model considering the asymmetry of skeleton curve is elaborated.The verifcation tests on saturated Nanjing fne sand are performed using a hollow cylinder apparatus to verify the applicability of the UD model.It is found that the predicted curves by the UD model agree well with the test data.