On the calibration of a shear stress criterion for rock joints to represent the full stress-strain profile

Conventional numerical solutions developed to describe the geomechanical behavior of rock interfaces subjected to differential load emphasize peak and residual shear strengths.The detailed analysis of preand post-peak shear stress-displacement behavior is central to various time-dependent and dynamic rock mechanic problems such as rockbursts and structural instabilities in highly stressed conditions.The complete stress-displacement surface(CSDS)model was developed to describe analytically the pre-and post-peak behavior of rock interfaces under differential loads.Original formulations of the CSDS model required extensive curve-fitting iterations which limited its practical applicability and transparent integration into engineering tools.The present work proposes modifications to the CSDS model aimed at developing a comprehensive and modern calibration protocol to describe the complete shear stressdisplacement behavior of rock interfaces under differential loads.The proposed update to the CSDS model incorporates the concept of mobilized shear strength to enhance the post-peak formulations.Barton’s concepts of joint roughness coefficient(JRC)and joint compressive strength(JCS)are incorporated to facilitate empirical estimations for peak shear stress and normal closure relations.Triaxial/uniaxial compression test and direct shear test results are used to validate the updated model and exemplify the proposed calibration method.The results illustrate that the revised model successfully predicts the post-peak and complete axial stressestrain and shear stressedisplacement curves for rock joints.

Bending results of graphene origami reinforced doubly curved shell

The present work investigates higher order stress,strain and deformation analyses of a shear deformable doubly curved shell manufactures by a Copper(Cu)core reinforced with graphene origami auxetic metamaterial subjected to mechanical and thermal loads.The effective material properties of the graphene origami auxetic reinforced Cu matrix are developed using micromechanical models cooperate both material properties of graphene and Cu in terms of temperature,volume fraction and folding degree.The principle of virtual work is used to derive governing equations with accounting thermal loading.The numerical results are analytically obtained using Navier's technique to investigate impact of significant parameters such as thermal loading,graphene amount,folding degree and directional coordinate on the stress,strain and deformation responses of the structure.The graphene origami materials may be used in aerospace vehicles and structures and defence technology because of their low weight and high stiffness.A verification study is presented for approving the formulation,solution methodology and numerical results.

Resilient performance of self-centering hybrid rocking walls with curved interface under pseudo-static loading

Frame and rocking wall(FRW)structures have excellent resilient performance during earthquakes.However,the concrete at interfacial corners of rocking walls(RWs)is easily crushed due to local extreme compression during the rocking process.An innovative RW with a curved interface is proposed to prevent interfacial corners from producing local damage,enhancing its earthquake resilient performance(ERP).The precast wall panel with a curved interface is assembled into an integral self-centering hybrid rocking wall(SCRW)by two post-tensioned unbonded prestressed tendons.Moreover,two ordinary energy dissipation steel rebars and two shear reinforcements are arranged to increase the energy dissipation capacity and lateral resistance.Two SCRW specimens and one monolithic reinforced concrete(RC)shear wall(SW)were tested under pseudo-static loading to compare the ERPs of the proposed SCRW and the SW,focusing on studying the effect of the curved interface on the SCRW.The key resilient performance of rocking effects,failure modes,and hysteretic properties of the SCRW were explored.The results show that nonlinear deformations of the SCRW are concentrated along the interface between the SCRW and the foundation,avoiding damage within the SCRW.The restoring force provided by the prestressed tendons can effectively realize self-centering capacity with small residual deformation,and the resilient performance of the SCRW is better than that of monolithic SW.In addition,the curved interface of the SCRW makes the rocking center change and move inward,partially relieving the stress concentration and crush of concrete.The rocking range of the rocking center is about 41.4%of the width of the SCRW.

Orientation dependency of shear stress-strain curves in B2-ordered Fe_3Al single crystals deformed in tension at room temperature

B2-ordered Fe3Al single crystals with various orientations were deformed in tension at room temperature in vacuum. The shape of shear stress-strain curves and work hardening rates were found to be strongly dependent on the orientation. The formation of the five different work hardening stages were considered to be related to the number of operative slip systems, the effect of secondary slip systems and the dissociation of the twofold superdislocation. Stage I is an easy glide stage corresponding to single slip. Stage II, with high hardening rate, often corresponds to the existence of conjugate slip systems. Stage III, with relatively low hardening rate, corresponds to the weaker hardening of secondary slip systems. Stage IV, with the highest hardening rate, is not only related to multiple slip but also the dissociation of twofold superdislocations and the moving of superpartials with an antiphase boundary (APB) trap. Stages V, with a negative hardening rate, may be caused by the cross slip of single dissociated superdislocation. The number of stages and the work hardening rate of the same stage were also found to change significantly, when the tensile orientation lies in different orientation regions.

Unified analytical stressstrain curve for quasibrittle geomaterial in uniaxial tension, direct shear and uniaxial compression

Considering strain localization in the form of a narrow band initiated just at peak stress, three analytical expressions for stressstrain curves of quasibrittle geomaterial (such as rock and concrete) in uniaxial tension, direct shear and uniaxial compression were presented, respectively. The three derived stressstrain curves were generalized as a unified formula. Beyond the onset of strain localization, a linear strain-softening constitutive relation for localized band was assigned. The size of the band was controlled by internal or characteristic length according to gradient-dependent plasticity. Elastic strain within the entire specimen was assumed to be uniform and decreased with the increase of plastic strain in localized band. Total strain of the specimen was decomposed into elastic and plastic parts. Plastic strain of the specimen was the average value of plastic strains in localized band over the entire specimen. For different heights, the predicted softening branches of the relative stressstrain curves in uniaxial compression are consistent with the previously experimental results for normal concrete specimens. The present expressions for the post-peak stressdeformation curves in uniaxial tension and direct shear agree with the previously numerical results based on gradient-dependent plasticity.

ISOCHRONOUS STRESS-STRAIN CURVES OF LOW ALLOY STEEL CROSS-WELD-SPECIMEN AT HIGH TEMPERATURE

In this work, a parametric approach is presented and utilized to determine the creep properties of weldments; then the model of creep strain for cross weld specimen is given. On the basis of the experimental results, attempt has been made to establish equations of the isochronous stress-strain for weld joint that can predict the function of loading and service time in use of the creep data of base metal and weld metal.

Numerical simulation of the stress-strain curve and the stress and strain distributions of the titanium-duplex alloy

The stress-strain curve of an α-β Ti-8Mn alloy was measured and then it was calculated with finite element method （FEM） based on the stress-strain curves of the single α and β phase alloys. By comparing the calculated stress-strain curve with the measured one, it can be seen that they fit each other very well. Thus, the FE model built in this work is effective. According to the above mentioned model, the distributions of stress and strain in the α and β phases were simulated. The results show that the stress gradients exist in both α and β phases, and the distributions of stress are inhomogeneous. The stress inside the phase is generally higher than that near the interface. Meanwhile, the stress in the α phase is lower than that in the β phase, whereas the strain in the α phase is higher than that in the β phase.

The Complete Stress-strain Curve of Recycled Aggregate Concrete under Uniaxial Compression Loading

The mechanical performance of recycled aggregate concrete （RAC） is investigated. An experiment on the complete stress-strain curve under uniaxial compression loading of RAC is carried out. The experimental results indicate that the peak stress, peak strain, secant modulus of the peak point and original point increase with the strength grade of RAC enhanced. On the contrary, the residual stress of RAC decreases with the strength grade enhancing, and the failure of RAC is often broken at the interface between the recycled aggregate and the mortar matrix. Finally, the constitutive model of stress-strain model of RAC has been constituted, and the results from the constitutive model of stress-strain meet the experiment results very well.

Charactersitics of Stress-strain Curve of High Strength Steel Fiber Reinforced Concrete under Uniaxial Tension

A whole of 110 specimens divided into 22 groups were tested with varying the volume fraction of steel fibers and the matrix strength of these specimens. The stress-strain behaviors of four types of steel fiber reinforced concrete （SFRC） under uniaxial tension were studied experimentally. When the matrix strength and the fiber content increase, the tensile stress and tensile strain vary differently according to the fiber type. The mechanisms of reinforcing effect for different types of fiber were analyzed and the stress-strain curves of the specimens were plotted. Some experimental factors for stress or strain of SFRC were given. A tensile toughness modulus Re0.5 was introduced to evaluate the toughness characters of SFRC under uniaxial tension. Moreover, the formula of the tensile stress-strain curve of SFRC was regressed. The theoretical curve and the experimental ones fit well, which can be used for references in construction.

APPROXIMATE VIBRATION ANALYSIS OF LAMINATED CURVED PANEL USING HIGHER-ORDER SHEAR DEFORMATION THEORY

An approximate analysis for free vibration of a laminated curved panel(shell)with four edges simply supported(SS2),is presented in this paper.The transverse shear deformation is considered by using a higher-order shear deformation theory.For solving the highly coupled partial differential governing equations and associated boundary conditions,a set of solution functions in the form of double trigonometric Fourier series,which are required to satisfy the geometry part of the considered boundary conditions,is assumed in advance.By applying the Galerkin procedure both to the governing equations and to the natural boundary conditions not satisfied by the assumed solution functions,an approximate solution,capable of providing a reliable prediction for the global response of the panel,is obtained.Numerical results of antisymmetric angle-ply as well as symmetric cross-ply and angle-ply laminated curved panels are presented and discussed.

A Comprehensive Investigation on Shear Performance of Improved Perfobond Connector

This paper presents an easily installed improved perfobond connector (PBL) designed to reduce the shearconcentration of PBL. The improvement of PBL lies in changing the straight penetrating rebar to the Z-typepenetrating rebar. To study the shear performance of improved PBL, two PBL test specimens which containstraight penetrating rebar and six improved PBL test specimens which contain Z-type penetrating rebars weredesigned and fabricated, and push-out tests of these eight test specimens were carried out to investigate andcompare the shear behavior of PBL. Additionally, Finite Element Analysis (FEA) models of the PBL specimenswere established and validated against the test results. Through FEA, the effects of concrete grade, perforatedplate’s aperture, Z-type penetrating rebar’s diameter, Z-type penetrating rebar’s bending angle, and bending lengthon shear behaviors were discussed. The results indicate that (1) Compared with PBL specimens with straightpenetrating rebars, Z-type penetrating rebar can significantly improve the shear resistance and shear stiffnessof the specimens. This enhanced performance can be mainly attributed to the increased adhesion of the transverserebar. (2) By comparing the load-slip curve, the slip of PBL test specimens which contain straight penetratingrebar increases rapidly and the bearing capacity decreases rapidly after concrete craking, while the bearingcapacity of Z-type penetrating rebar specimens decreases first and then increases gradually, showing betterductility. (3) The stress of the PBL shear connector with Z-type penetrating rebar is more uniform than thePBL shear connector with straight penetrating rebar, and the overall deformation is more uniform. (4) The higherthe concrete grade, the higher the shear bearing capacity and the better ductility of the new PBL. Increasing theaperture of the perforated plate or the diameter of the rebar has a very limited effect on the improvement of theshear capacity of PBL. Through the systematic analysis of the mechanical properties of Z-type penetrating rebarPBL specimen, the experimental reference is provided for improving the structure and design of new type PBL.

A Method for Elastic Shear Buckling Calculation of Curved Bridge Webs

Curved composite bridges and curved steel bridges have already been constructed around the world;however, the calculation for shear buckling of curved bridge webs generally uses the equations for straight bridge webs or just introduces a modification factor for bridge design. In this paper, the curved bridge web is equivalent to an isotropic cylindrical flat shell, and the double triangular series satisfying four-edge simply supported boundaries are used as the displacement function of the shell. Then by means of the Galerkin method, the analytical formula for elastic shear buckling stress of curved bridge webs is deduced. The parameter studies show that the shear buckling coefficient kc of curved bridge webs is positively correlated with the parameter h2 / (Rt), and negatively correlated with the length-height ratio l/ h. This implies that the elastic shear buckling stress of a curved bridge web is larger than that of an equivalent straight bridge web. For a curved bridge with the parameter h2 / (Rt) less than 2, the amount of increase is less than 4.5%. The elastic shear buckling stress of curved bridge webs can be estimated conservatively as the webs in straight bridges. While for a curved bridge with larger h2 / (Rt), using the equations for straight girders to calculate the elastic shear buckling stress is too conservative. The proposed formulas provide a more accurate estimation for shear buckling stress of curved bridge webs.

Relations of complete creep processes and triaxial stress-strain curves of rock

Based on the results of triaxial compressive creep tests for five kinds of rock under the different stress loading,unloading and cycle-loading-unloading conditions,the creep deformation is not only a function of stress and time,but also it has the corresponding relations to the triaxial stress-strain curves of rock.The deformation properties of soften-strain,harden-strain and ideal plasticity presented by conventional triaxial compressive test curves under the different stress states were utilized,and the creep characteristics,the creep starting stress and the different entire creep process curves of rock were studied systematically according to creep experiment results,and the relations of the triaxial stress-strain curves to the creeping starting stress,the terminating curve,the different creep processes,and the different creep fracture properties were established.The relations presented in this paper were verified partially by the creep experiment results of five types of rock.

MODELLING OF TENSILE STRESS-STRAIN CURVE OF WOVEN FABRICS

A general shape of tensile stress-strain curves of woven fabrics is first recognised by puttingtested and predicted results together.An exponential function with two parameters is then selectedfor the prediction of tensile stress-strain relationship.The predicted results by using the proposedfunction show excellent agreement with experimental data.

Investigation into the stress-strain curves of deformation-induced ferrite transformation in a low carbon steel

A series of tests of deformation-induced ferrite transformation （DIP-T） in a low carbon steel were carried out by the Gleeble-3500 hot simulation machine at a temperature range of Ae3-Ar3. The overall stress-strain curves during DIFT can be divided into three typical types： ＂double-humped＂,＂ single-humped＂ and ＂transitional＂. The peaks exhibited in the curve are involved with deformation-induced transformation which happened in grains or at the grain boundaries. According to the stress-time curve and strain-time curve, strain capacity dramatically postponed the strain-induced transformation, which leads to the start of the transformation right ahead of the finish of deformation and the majority of the ferrite transformation process mainly happened after the deformation. Deformation-induced transformation is a metadynamic transformation process with dynamic nucleation.

EFFECT OF TRANSVERSE SHEAR ON FINITE DEFORMATION OF GENERALLY LAMINATED SHALLOW SHELL WITH DOUBLE CURVATURE

Nonlinear equations of equilibrium for the titled shell of rectangular planform under transverse and inplane edge loads are derived by using the virtual work principle and expressed in terms of a stress function,the transverse displacement and two rotation functions.The sheU is elastically re- strained against rotation.A generalized double Fourier series solution is formulated for nonlinear bending of the shell.The Galerkin technique furnishes an infinite set of simultaneous nonlinear alge- braic equations for the above four variables,which can be truncated to obtain any desired degree of ac- curacy.Numerical results for antisymmetrically laminated angle-ply and cross-ply graphite-epoxy doubly curved panels are presented graphically for the transverse shear effect and various shell parame- ters and boundary conditions.The present results are also compared with available data.

High temperature stress–strain curves of MnS and their applications in finite element simulation

A novel method for testing stress–strain curves of non-metallic materials was presented.The high temperature stress-strain curves of MnS were preliminarily obtained and corrected to account for the influence of friction.Using the finite element method,the influence of deformation parameters on the deformation evolution of MnS inclusions was investigated based on the experimental reference data.The corresponding physical experiment was designed for comparative analysis.The results indicate that the experimental high-temperature deformation data of MnS are highly reliable.In the process of matrix deformation,the shapes of MnS inclusions change from spherical to ellipsoidal and even to lamellar.There are some differences in the morphological deformation of MnS inclusions located at different positions.With the increase in the initial size of MnS inclusions,the risk of failing the inclusion-flaw inspection increases and the forging quality further deteriorates.

Factors Influencing the Disturbed Flow Patterns Downstream of Curved Atherosclerotic Arteries

Pulsatile blood flows in curved atherosclerotic arteries are studied by computer simulations. Computations are carried out with various values of physiological parameters to examine the effects of flow parameters on the disturbed flow patterns downstream of a curved artery with a stenosis at the inner wall. The numerical results indicate a strong dependence of flow pattern on the blood viscosity and inlet flow rate, while the influence of the inlet flow profile to the flow pattern in downstream is negligible.

Finite Element Modeling of Stress Strain Curve and Micro Stress and Micro Strain Distributions of Titanium Alloys— A Review

Most of the alloys like titanium, steel, brass, copper, etc., are used in engineering applications like automobile, aero- space, marine etc., consist of two or more phases. If a material consists of two or more phases or components it is very difficult to predict the properties like mechanical and other properties based on simple laws such as rule of mixtures. Titanium alloys are capable of producing different microstructures when it subjected to heat treatments, so much of money and time are squandering to study the effect of microstructure on mechanical properties of titanium alloys. This squandering can be reduced with the help of modeling and optimization techniques. There are many modeling tech- niques like Finite element method, Mat lab, Mathematical modeling etc. are available. But Finite element method is widely used for prediction because of capable of producing distributions of stresses and strains at any different loads. From the literature it is observed that there is a good agreement between the calculated and measured stress strain curves. This review paper describes the effect of volume fraction and grain size of alpha phase on the stress strain curve of the titanium alloys. It also can predict the effect of strength ratio on stress strain curve by using FEM. This informa- tion will be of great use in designing and selecting the titanium alloys for various engineering applications.