Effects of Material Composition and Water Content on the Mechanical Properties of Landslide Deposits Triggered by the Wenchuan Earthquake

Abundant landslide deposits were triggered by the Wenchuan earthquake, providing a rich source of material for subsequent debris flows or slope failures under rainfall conditions. A good understanding of the physical and mechanical properties of the landslide deposits is very important to the research on slope failure mechanisms and the initiation of debris flow. Laboratory biaxial compression tests are used to study the material compositions and water content impacts on the mechanical properties of landslide deposits, and a discrete element method （a bond-contact model） is used to study the particle stiffness, bond force, friction coefficient and confining stress impact on the mechanical behaviors and the relationships between the numerical and experimental parameters. The experimental results show that the failure stress of landslide deposits is decreased with increasing content of fine particles and also with increased water content, especially at the initial increasing stage. Cohesion of the saturated landslide deposits is increased, but the friction angle is decreased with the increase in the fine particle content. Shear strength parameters （the cohesion and friction angle） are decreased with the increasing water content at the initial increasing stage, and then, they slowly decrease. There is a critical value of the water content at 5%-7% （in weight） for the failure stress and shear strength parameters of the landslide deposits. Quadratic equations are presented to describe the relation between the bond force and cohesion, and the numerical friction coefficient and the experimental friction angle.

Diagnosis of dynamic process over rainband of landfall typhoon

This paper introduces a new physical parameter -- thermodynamic shear advection parameter combining the perturbation vertical component of convective vorticity vector with the coupling of horizontal divergence perturbation and vertical gradient of general potential temperature perturbation. For a heavy-rainfall event resulting from the landfall typhoon ＇Wipha＇, the parameter is calculated by using National Centres for Enviromental Prediction/National Centre for Atmospheric Research global final analysis data. The results showed that the parameter corresponds to the observed 6 h accumulative rainband since it is capable of catching hold of the dynamic and thermodynamic disturbance in the lower troposphere over the observed rainband. Before the typhoon landed, the advection of the parameter by basic-state flow and the coupling of general potential temperature perturbation with curl of Coriolis force perturbation are the primary dynamic processes which are responsible for the local change of the parameter. After the typhoon landed, the disturbance is mainly driven by the combination of five primary dynamic processes. The advection of the parameter by basic-state flow was weakened after the typhoon landed.

Rock borehole shear tests in dam foundation of Xiangjiaba hydropower station

Xiangjiaba hydropowcr station is one of the complicated geological conditions of its dam foundation, parameters of rock masses are very important issues. To cascade power stations on the Jinsha River, China. Due to the evaluating the rock mass quality and determining the mechanical address these issues, several groups of rock borehole shear tests （RBSTs） were conducted on the black mudstone in the dam foundation of Xiangjiaba hydropower station in the second construction phase. Forty three groups of shear strengths of black mudstone samples were obtained from RBSTs, and the shear strength parameters （c and f） were calculated using the least squares method. In addition, the limitations and merits of RBST employed in the Xiangjiaba hydropower station were discussed. Test results indicate that the shear strength parameters obtained from RBST have a good correlation with the results from sotmd wave test in borehole. It is believed that RBST has a good adaptability and applicability in geotechnical engineering.

Diagnostic Analysis of Wave Action Density During Heavy Rainfall Caused by Landfalling Typhoon

Based on prior investigation,this work defined a new thermodynamic shear advection parameter,which combines the vertical component of convective vorticity vector,horizontal divergence,and vertical gradient of generalized potential temperature.The interaction between waves and fundamental states was computed for the heavyrainfall event generated by landfalling typhoon“Morakot”.The analysis data was produced by ADAS[ARPS(Advanced Regional Prediction System)Data Analysis System]combined with the NCEP/NCAR final analysis data(1°×1°,26 vertical pressure levels and 6-hour interval)with the routine observations of surface and sounding.Because it may describe the typical vertical structure of dynamical and thermodynamic fields,the result indicates that the parameter is intimately related to precipitation systems.The parameter’s positive high-value area closely matches the reported 6-hour accumulated surface rainfall.And the statistical analysis reveals a certain correspondence between the thermodynamic shear advection parameter and the observed 6-hour accumulated surface rainfall in the summer of 2009.This implies that the parameter can predict and indicate the rainfall area,as well as the initiation and evolution of precipitation systems.

Geotechnical Characterization of Silty Clay Reinforcedwith Jute Cloth as Waster Product

Soil reinforcement is a recent and special field of soil improvement.It covers a range of techniques,which consists of placing inclusions in soil.The most conferences devoted partly or totally the behavior of foundation on reinforced subgrade without regarding the basic characteristics of the reinforced soil.So,the paper presents an experimental investigation into the mechanical and compressibility properties of the reinforced silty clay samples by jute cloth at intermediate depth.The effects of the reinforcement on shear stress and shear failure were studied;also,the presence of the reinforcement on behavior of consolidation process was distinctly described.The laboratory tests were supported by the finite element analysis to identify only the consolidation process and explained the effect of the reinforcement on the effective vertical stress and pore water pressure.The results indicated that the presence of such reinforcement has a considerable effect in increasing the shear strength of the reinforced samples and decreasing the compressibility especially decreasing the soil movement also,relieving both the effective and pore water pressure.

Shear Failure Criterion and Constant Volume Ring Shear Testing Method for Clayey Soil

This paper discusses the shortcomings of the traditional Coulomb shear criterion and the direct shear-box testing method used for clayey soil and presents a modified shear criterion that considers the elasto-plastic behavior of cohesive soil. This modified approach involves direct shear testing under constant volume, a method that has been developed by the author. A modified ring shear apparatus and the theory behind the shear criterion and its implication for slope stability analysis are then discussed and the results of investigated tuffitic clayey sediments are presented. The results show that the presented new shear criterion does not consider the cohesion as material constant, but rather it depends on the void ratio. In this case, the stress state and the consolidation status and thus the elasto-plastic behavior of the clayey soil are considered.

Study on Shear Strength Characteristics of Basalt-Concrete Bonding Interface Based on in-situ Direct Shear Test

In rock engineering,the shear strength of the basalt-concrete bonding interface is a key factor affecting the shear performance of hydroelectric dam foundations,embedded rock piles and rock bolts.In this study,30 sets of in-situ direct shear tests were conducted on the basalt-concrete bond interface in the Baihetan dam area to investigate the shear strength characteristics of the basalt-concrete bonding interface.The bonding interface contains two states,i.e.,the bonding interface is not sheared,termed as se(symbolic meaning see Table 1);the bonding interface is sheared with rupture surface,termed as si.The effects of lithology,Joints structure,rock type grade and concrete compressive strength on the shear strength of the concrete-basalt contact surface were investigated.The test results show that the shear strength of the bonding interface(s_(e)&s_(i))of columnar jointed basalt with concrete is greater than that of the bonding interface(s_(e)&s_(i))of non-columnar jointed one with the same rock type grade.When the rock type grade isⅢ_(2),fcol is 1.22 times higher than fncol and ccol is 1.13 times greater than cncol.The shear strength parameters of the basalt-concrete bonding interface differ significantly for different lithologies.The cohesion of the bonding interface(s_(i))of cryptocrystalline basalt with concrete is 2.05 times higher than that of the bonding interface(s_(i))of breccia lava with concrete under the same rock type grade condition.Rock type grade has a large influence on the shear strength of the non-columnar jointed basalt-concrete bonding interface(s_(e)&s_(i)).cnol increases by 33%when the grade of rock type rises fromⅢ_(1)toⅡ_(1).the rock type grade has a greater effect on bonding interface(s_(i))cohesion than the coefficient of friction.When the rock type grade is reduced fromⅢ_(2)toⅢ_(1),f_(ncol)′increases by 2%and c_(ncol)′improves by 44%.The shear strength of the non-columnar jointed basalt-concrete bonding interface(s_(e)&s_(i))increases with the increase of the compressive strength of concrete.When concrete compressive strength rises from 22.2 to 27.6 MPa,the cohesion increases by 94%.

Effect of loading rate on shear strength parameters of mechanically and biologically treated waste

Mechanical biological treatment(MBT)technology has attracted increasing attention because it can reduce the volume of waste produced.To deal with the current trend of increasing waste,MBT practices are being adopted to address waste generated in developing urban societies.In this study,a total of 20 specimens of consolidated undrained triaxial tests were conducted on waste obtained from the Hangzhou Tianziling landfill,China,to evaluate the effect of loading rate on the shear strength parameters of MBT waste.The MBT waste samples exhibited an evident strain-hardening behavior,and no peak was observed even when the axial strain exceeded 25%.Further,the shear strength increased with an increase in the loading rate;the effect of loading rate on shear strength under a low confining pressure was greater than that under a high confining pressure.Furthermore,the shear strength parameters of MBT waste were related to the loading rate.The relationship between the cohesion,internal friction angle,and logarithm of the loading rate could be fitted to a linear relationship,which was established in this study.Finally,the ranges of shear strength parameters cohesion c and effective cohesion c′were determined as 1.0–8.2 kPa and 2.1–14.9 kPa,respectively;the ranges of the internal friction angleφand effective internal friction angleφ’were determined as 16.2°–29°and 19.8°–43.9°,respectively.These results could be used as a valuable reference for conducting stability analyses of MBT landfills.

Study on Shear Strength Characteristics of Columnar Jointed Basalt Based on in-situ Direct Shear Test at Baihetan Hydropower Station

Columnar jointed basalt(CJB) widely distributes in the dam site of the Baihetan Hydropower Station.The columnar joint structure and fracture development of CJB have significant influence on the mechanical properties of rock mass,and the mechanical properties of CJB are of great significance to the Baihetan Hydropower Project.Therefore,in-situ direct shear tests were carried out on ten test adit at different locations in the dam site area to study the shear behavior of CJB.In this study,21 sets of in-situ direct shear tests were conducted for rock types of type Ⅱ_(2),type Ⅲ_(1)and type Ⅲ_(2),with horizontal and vertical shear planes and two different specimen sizes of CJB.Shear strength parameters of CJB were obtained by linear fitting of in-situ direct shear test results based on the Mohr-Coulomb strength criterion.The results indicate that the shear strength parameters of CJB with horizontal shear plane increase as the increase of rock type grade.The shear strength parameters of CJB show obvious anisotropy and the friction coefficient of the horizontal shear plane is greater than the vertical shear plane.The friction coefficient in the horizontal direction of the shear plane is 1.27 times that in the vertical direction of the shear plane.With the increase of rock type grade,the difference of friction coefficient becomes larger.However,the cohesion changes little whether the shear plane is horizontal or vertical.In addition,the size effect of CJB in this area is significant.The shear strength parameters of large size(100 cm × 100 cm) specimens are lower than those of regular size(50 cm × 50 cm) specimens.The reduction of cohesion is greater than that of the friction coefficient.For rock type Ⅲ_(2),the cohesion of large-size specimens is 0.637 of the regular-size specimens.The reduction percentage of the friction coefficient for type Ⅲ_(2)is 1.66 times that of type Ⅲ_(1).The reduction percentage of the cohesion for type Ⅲ_(2)is 1.27 times that of type Ⅲ_(1).The size effect decreases with the increase of rock type grade.The research results of this study can provide an important basis for the selection of rock mechanics parameters in the dam site area of Baihetan Hydropower Station and the stability analysis of the dam foundation and rocky slopes.

Solid solution strengthening of high-entropy alloys from first-principles study

Solid solution strengthening(SSS)is one kind of strengthening mechanisms and plays an important role in alloy design,in particular for single-phase alloys including high-entropy alloys(HEAs).The classical Labusch–Nabarro model and its expansions are most widely applicable to treating SSS of solid solution alloys including both conventional alloys(CAs)and HEAs.In this study,the SSS effects in a series of Febased CAs and HEAs are investigated by using the classical Labusch–Nabarro model and its expansions.The size misfit and shear modulus misfit parameters are derived from first-principles calculations.Based on available experimental data in combination with empirical SSS model,we propose fitting constants(i.e.,the ratio between experimental hardness and predicted SSS effect)for these two families of alloys.The predicted host/alloy family-dependent fitting constants can be used to estimate the hardness of these SSS alloys.General agreement between predicted and measured hardness values is satisfactory for both CAs and HEAs,implying that the proposed approach is reliable and successful.