Introduction: The current discussion about the use of short implants to avoid bone-augmentation (“sinus lift”) in the lateral maxilla remains a controversial topic and is increasingly at odds with the reality of evo...Introduction: The current discussion about the use of short implants to avoid bone-augmentation (“sinus lift”) in the lateral maxilla remains a controversial topic and is increasingly at odds with the reality of evolutionary biology. Aim of the study was to determine the percentage of cases from a large routine patient-sample in which short implants might be suitable to avoid sinus lift procedures. Materials and Methods: From January 2012 to June 2015, all patients in three general dental practices in Austria with at least one subantral edentulous area were subjected to routine panoramic X-ray screening. The subantral alveolar ridge heights and the mesial extension of the maxillary sinus towards the canine fossa were measured. Statistics were performed by Excel data analysis (mean value, standard deviation). Results: 2837 patients were screened with 2837 panoramic radiographs presenting 3528 edentulous subantral regions and the subantral bone heights of 5674 maxillary sinuses were surveyed. 57.43% revealed subantral alveolar ridge heights of 4 mm or less;24.43% of all measure-points indicated a maximum alveolar ridge height of 6 mm. In 39.32% of cases, the pneumatisation of the maxillary sinuses with a subantral residual ridge height of 6 mm or less extended as far as the anatomical position of the second premolars, in 20.51% as far as the position of the first premolar and in 10.84% as far as the canine fossa. Discussion: The sinus lift procedure will continue to be one of the basic standard surgical procedures carried out by practice-based dental surgeons who perform implant surgery since in at least two thirds of the cases short implants with lengths of less than 6 mm cannot be applied. Preference should be given to sinus lift-procedures, which can be learned safely with a minimum of time-effort, least risk of failure and lowest possible level of patient morbidity. Transcrestal hydrodynamic ultrasonic sinus lift-procedures with piezotomes seem to fulfill these basic demands.展开更多
Although short implants are seen as alternative treatments that require additional surgical techniques in posterior region, they can be applied to anterior maxilla and various studies are required on this subject. The...Although short implants are seen as alternative treatments that require additional surgical techniques in posterior region, they can be applied to anterior maxilla and various studies are required on this subject. The purpose of this study was to examine and compare the peak von Mises stress distributions in the crown, implant and abutment by using finite element analysis (FEA). Besides, a comparison of the implant-abutment connection types in the short implant with the FEA method was established. A short implant (4 × 5 mm) with a taper-lock connection and a regular implant (4 × 9 mm) with a screw connection were used in maxillary central incisor tooth area. Three different titanium abutments with 0?, 15? and 25? angles were used for abutments. In addition, in order to determine whether the stress change in short implants is due to the length of the implant-abutment connection, a screw was designed for a short implant and it was also evaluated in the same three angles. A total of three groups and nine models were generated. 114.6N load was applied to the cingulum area of the crown at an angle of 135? to the long axis of the crowns. A torque load of 25 Ncm was applied to the regular and short implant screw. Von Mises stress distributions of implants, abutments and crowns were evaluated by using FEA. Increased angle in implants increased von Mises stress values of implant, abutment and crown. Screw connection was found higher at all angles in short implants. Close values were found at different angles in taper-lock short implant crowns. The length and the angle in the bone of implant with the type of implant-abutment connection results in the accumulated stress values. Clinical Implications Taper implant-abutment connection system was found to be more promising in terms of stress accumulation in crowns. Although the amount of stress on the abutment increased due to the length of the implant in short implants, taper implant-abutment connection system slightly reduced related to this increase.展开更多
背景:随着无牙颌修复需求增加,“All-on-4”技术被广泛应用。种植体与天然牙的载荷传递方式不同,三维有限元分析可研究功能载荷作用下种植体及周围骨组织的应力分布,并在此基础上为寻找适合的种植体材料、优化种植体的几何结构、设计临...背景:随着无牙颌修复需求增加,“All-on-4”技术被广泛应用。种植体与天然牙的载荷传递方式不同,三维有限元分析可研究功能载荷作用下种植体及周围骨组织的应力分布,并在此基础上为寻找适合的种植体材料、优化种植体的几何结构、设计临床手术方案提供了研究方法。目的:对三维有限元分析法在“All-on-4”技术方面的相关研究作一综述。方法:检索中国知网和PubMed数据库2003-2023年相关文献,英文检索词为“Finite Element Method,All-on-4,edentulous,Biomechanics”,中文检索词为“有限元,All-on-4,无牙颌,生物力学”,根据纳入排除标准筛选符合标准的文献,最终纳入65篇文献进行综述。结果与结论:①对水平骨量不足的情况,研究者们可以选择应用窄直径种植体,但需要注意悬臂的存在对应力分布的影响,降低失败的风险。②“All-on-4”概念通过倾斜远中种植体的方法,减少骨的应力分布,但在不同的颌骨类型中,远中种植体倾斜的理想角度还需要进一步的研究。③悬臂的存在会增加种植失败的风险,将悬臂长度/AP距(CL/AP)的比值控制在0.9时,有助于减少机械并发症的发生。④用弹性模量较低的材料制作支架时,支架自身的应力较小,但会增加种植体、中央螺丝、基台及种植体周围骨组织的应力,相反使用弹性模量较大的材料,会降低修复体组件和种植体周围骨组织的应力,但支架本身的应力较高。⑤“All-on-4”概念可以实现较好的力学平衡,但需结合患者自身的具体情况制定一个长期有效的治疗方案。⑥合理的咬合设计是影响种植治疗成功的关键,尖牙引导牙合和组牙功能牙合在修复体的寿命方面无差异。然而,影响咬合设计的原因有很多,未来还需要进一步的体外实验以及大量临床研究来探索“All-on-4”理想的咬合设计。展开更多
Background In a three-month report from the CGA-TAVI registry, we found the Multidimensional Prognostic Index (MPI) and Short Physical Performance Battery (SPPB) to be of value for predicting short-term outcomes in el...Background In a three-month report from the CGA-TAVI registry, we found the Multidimensional Prognostic Index (MPI) and Short Physical Performance Battery (SPPB) to be of value for predicting short-term outcomes in elderly patients undergoing transcatheter aortic valve implantation (TAVI). In the present analysis, we examined the association of these tools with outcomes up to one year post-TAVI. Methods CGA-TAVI is an international, observational registry of geriatric patients undergoing TAVI. Patients were assessed using the MPI and SPPB. Efficacy of baseline values and any postoperative change for predicting outcome were established using logistic regression. Kaplan- Meier analysis was carried out for each comprehensive geriatric assessment tool, with survival stratified by risk category. Results One year after TAVI, 14.1% of patients deceased, while 17.4% met the combined endpoint of death and/or non-fatal stroke, and 37.7% the combined endpoint of death and/or hospitalisation and/or non-fatal stroke. A high-risk MPI score was associated with an increased risk of all-cause mortality (aOR = 36.13, 95% CI: 2.77–470.78, P = 0.006) and death and/or non-fatal stroke (aOR = 10.10, 95% CI: 1.48–68.75, P = 0.018). No significant associations were found between a high-risk SPPB score and mortality or two main combined endpoints. In contrast to a worsening SPPB, an aggravating MPI score at three months post-TAVI was associated with an increased risk of death and/or non-fatal stoke at one year (aOR = 95.16, 95% CI: 3.41–2657.01). Conclusions The MPI showed value for predicting the likelihood of death and a combination of death and/or non-fatal stroke by one year after TAVI in elderly patients.展开更多
This study reports a hybrid method which allows the formation of biocomposites on stainless steel implants. The main idea of the method is to create multilayer coatings consisting of titanium primer layer and a microa...This study reports a hybrid method which allows the formation of biocomposites on stainless steel implants. The main idea of the method is to create multilayer coatings consisting of titanium primer layer and a microarc calcium-phosphate coating. The titanium layer is deposited from plasma of continuous vacuum-arc discharge, and calcium-phosphate coating is formed by the microarc oxidation technique. The purpose of the hybrid method is to combine the properties of good strength stainless steel with high bioactivity of calcium-phosphate coating. This paper describes the chemical composition, morphology characteristics, adhesion and the ability of the formed biocomposites to stimulate the processes of osteoinduction. It is expedient to use such biocomposites for implants which carry heavy loads and are intended for long-term use, e.g. total knee endoprosthesis.展开更多
文摘Introduction: The current discussion about the use of short implants to avoid bone-augmentation (“sinus lift”) in the lateral maxilla remains a controversial topic and is increasingly at odds with the reality of evolutionary biology. Aim of the study was to determine the percentage of cases from a large routine patient-sample in which short implants might be suitable to avoid sinus lift procedures. Materials and Methods: From January 2012 to June 2015, all patients in three general dental practices in Austria with at least one subantral edentulous area were subjected to routine panoramic X-ray screening. The subantral alveolar ridge heights and the mesial extension of the maxillary sinus towards the canine fossa were measured. Statistics were performed by Excel data analysis (mean value, standard deviation). Results: 2837 patients were screened with 2837 panoramic radiographs presenting 3528 edentulous subantral regions and the subantral bone heights of 5674 maxillary sinuses were surveyed. 57.43% revealed subantral alveolar ridge heights of 4 mm or less;24.43% of all measure-points indicated a maximum alveolar ridge height of 6 mm. In 39.32% of cases, the pneumatisation of the maxillary sinuses with a subantral residual ridge height of 6 mm or less extended as far as the anatomical position of the second premolars, in 20.51% as far as the position of the first premolar and in 10.84% as far as the canine fossa. Discussion: The sinus lift procedure will continue to be one of the basic standard surgical procedures carried out by practice-based dental surgeons who perform implant surgery since in at least two thirds of the cases short implants with lengths of less than 6 mm cannot be applied. Preference should be given to sinus lift-procedures, which can be learned safely with a minimum of time-effort, least risk of failure and lowest possible level of patient morbidity. Transcrestal hydrodynamic ultrasonic sinus lift-procedures with piezotomes seem to fulfill these basic demands.
文摘Although short implants are seen as alternative treatments that require additional surgical techniques in posterior region, they can be applied to anterior maxilla and various studies are required on this subject. The purpose of this study was to examine and compare the peak von Mises stress distributions in the crown, implant and abutment by using finite element analysis (FEA). Besides, a comparison of the implant-abutment connection types in the short implant with the FEA method was established. A short implant (4 × 5 mm) with a taper-lock connection and a regular implant (4 × 9 mm) with a screw connection were used in maxillary central incisor tooth area. Three different titanium abutments with 0?, 15? and 25? angles were used for abutments. In addition, in order to determine whether the stress change in short implants is due to the length of the implant-abutment connection, a screw was designed for a short implant and it was also evaluated in the same three angles. A total of three groups and nine models were generated. 114.6N load was applied to the cingulum area of the crown at an angle of 135? to the long axis of the crowns. A torque load of 25 Ncm was applied to the regular and short implant screw. Von Mises stress distributions of implants, abutments and crowns were evaluated by using FEA. Increased angle in implants increased von Mises stress values of implant, abutment and crown. Screw connection was found higher at all angles in short implants. Close values were found at different angles in taper-lock short implant crowns. The length and the angle in the bone of implant with the type of implant-abutment connection results in the accumulated stress values. Clinical Implications Taper implant-abutment connection system was found to be more promising in terms of stress accumulation in crowns. Although the amount of stress on the abutment increased due to the length of the implant in short implants, taper implant-abutment connection system slightly reduced related to this increase.
文摘背景:随着无牙颌修复需求增加,“All-on-4”技术被广泛应用。种植体与天然牙的载荷传递方式不同,三维有限元分析可研究功能载荷作用下种植体及周围骨组织的应力分布,并在此基础上为寻找适合的种植体材料、优化种植体的几何结构、设计临床手术方案提供了研究方法。目的:对三维有限元分析法在“All-on-4”技术方面的相关研究作一综述。方法:检索中国知网和PubMed数据库2003-2023年相关文献,英文检索词为“Finite Element Method,All-on-4,edentulous,Biomechanics”,中文检索词为“有限元,All-on-4,无牙颌,生物力学”,根据纳入排除标准筛选符合标准的文献,最终纳入65篇文献进行综述。结果与结论:①对水平骨量不足的情况,研究者们可以选择应用窄直径种植体,但需要注意悬臂的存在对应力分布的影响,降低失败的风险。②“All-on-4”概念通过倾斜远中种植体的方法,减少骨的应力分布,但在不同的颌骨类型中,远中种植体倾斜的理想角度还需要进一步的研究。③悬臂的存在会增加种植失败的风险,将悬臂长度/AP距(CL/AP)的比值控制在0.9时,有助于减少机械并发症的发生。④用弹性模量较低的材料制作支架时,支架自身的应力较小,但会增加种植体、中央螺丝、基台及种植体周围骨组织的应力,相反使用弹性模量较大的材料,会降低修复体组件和种植体周围骨组织的应力,但支架本身的应力较高。⑤“All-on-4”概念可以实现较好的力学平衡,但需结合患者自身的具体情况制定一个长期有效的治疗方案。⑥合理的咬合设计是影响种植治疗成功的关键,尖牙引导牙合和组牙功能牙合在修复体的寿命方面无差异。然而,影响咬合设计的原因有很多,未来还需要进一步的体外实验以及大量临床研究来探索“All-on-4”理想的咬合设计。
基金provided by Edwards Lifesciences (Nyon, Switzerland) to the Sponsor IPPMed (Cloppenburg, Germany)funding from Edwards Lifesciences as did Andrea Ungar
文摘Background In a three-month report from the CGA-TAVI registry, we found the Multidimensional Prognostic Index (MPI) and Short Physical Performance Battery (SPPB) to be of value for predicting short-term outcomes in elderly patients undergoing transcatheter aortic valve implantation (TAVI). In the present analysis, we examined the association of these tools with outcomes up to one year post-TAVI. Methods CGA-TAVI is an international, observational registry of geriatric patients undergoing TAVI. Patients were assessed using the MPI and SPPB. Efficacy of baseline values and any postoperative change for predicting outcome were established using logistic regression. Kaplan- Meier analysis was carried out for each comprehensive geriatric assessment tool, with survival stratified by risk category. Results One year after TAVI, 14.1% of patients deceased, while 17.4% met the combined endpoint of death and/or non-fatal stroke, and 37.7% the combined endpoint of death and/or hospitalisation and/or non-fatal stroke. A high-risk MPI score was associated with an increased risk of all-cause mortality (aOR = 36.13, 95% CI: 2.77–470.78, P = 0.006) and death and/or non-fatal stroke (aOR = 10.10, 95% CI: 1.48–68.75, P = 0.018). No significant associations were found between a high-risk SPPB score and mortality or two main combined endpoints. In contrast to a worsening SPPB, an aggravating MPI score at three months post-TAVI was associated with an increased risk of death and/or non-fatal stoke at one year (aOR = 95.16, 95% CI: 3.41–2657.01). Conclusions The MPI showed value for predicting the likelihood of death and a combination of death and/or non-fatal stroke by one year after TAVI in elderly patients.
文摘This study reports a hybrid method which allows the formation of biocomposites on stainless steel implants. The main idea of the method is to create multilayer coatings consisting of titanium primer layer and a microarc calcium-phosphate coating. The titanium layer is deposited from plasma of continuous vacuum-arc discharge, and calcium-phosphate coating is formed by the microarc oxidation technique. The purpose of the hybrid method is to combine the properties of good strength stainless steel with high bioactivity of calcium-phosphate coating. This paper describes the chemical composition, morphology characteristics, adhesion and the ability of the formed biocomposites to stimulate the processes of osteoinduction. It is expedient to use such biocomposites for implants which carry heavy loads and are intended for long-term use, e.g. total knee endoprosthesis.