A method to calculate design tide levels on the basis of numerical model of tidal current and its application

In order to determine the design tide levels in the areas without measured tide level data, especially in the areas where it is difficult to measure tidal levels, a calculation method based on a numerical model of tidal current is proposed. The essentials of the method are described, and its application is illustrated with an example. The results of the application show that the design tide levels calculated by the method are close to those determined by long-time measured tide level data, and its calculation precision is high, so it is feasible to use the method to determine the design tide levels in the areas.

Late Quaternary sedimentary environmental evolution offshore of the Hangzhou Bay,East China——implications for sea level change and formation of Changjiang alongshore current

This study focuses on sedimentary environmental changes offshore of Hangzhou Bay, East China, since the Late Quaternary. AMS ^14C ages from core CJK10, lithologies, distribution of foraminifera, heavy minerals, and S and C1 elements show a fluvial terrace environment during -23.2-11.0 cal ka BP; a littoral to tidal-flat environment during 11.0-10.2 cal ka BP; and a shallow marine environment with a relatively low sedimentation rate （0.1-0.22 cm/a） since 4.3 cal ka BP. High depositional rates （-1.6 cm/a） from 10.9 to 10.2 cal ka BP resulted from sufficient accommodation space created by rapid sea level rise from -44 m to -33 m, from high sediment delivery by local rivers, and effective trapping of sediments by tidal-flat vegetation. The rate of sea level rise was variable; relatively high from 10.9 to 10.6 cal ka BP （2.1 cm/a）, and lower since 10.6 cal ka BP （1.2 cm/a）. The Changjiang alongshore current crossed the Hangzhou Bay to form the mud wedge on the inner shelf of the East China Sea later than 9.4 cal ka BP. The CJK10 site was a tide-dominated shelf environment and experienced erosion from approximately 9.4-9.2 cal ka BP to 4.3 cal ka BP. The depositional hiatus was caused by the Changjiang alongshore current, which was relatively weak during 9.4-7.5 cal ka BP and increased in strength during -7.5-4 cal ka BP. From -4.3 cal ka BP, a large amount of sediment from the Changjiang River was partly deposited on the continental shelf of Hangzhou Bay with some transported southward. Therefore, this study clarifies the history of Changjiang-derived sediment dispersal and deposition, although a detailed record of the changes in the Chang3iang alongshore current since 4.3 cal ka BP is difficult to obtain because of the scarcity of evidence.

Zero-sequence Circulating Current Reduction for Three-phase Three-level Modular Photovoltaic Grid-connected Systems

针对共享正、负母线和交流母线的三相三电平模块化光伏并网系统的零序环流问题,建立三电平模块化系统零序环流的等效模型,并根据激励源的不同将零序环流分成3类,提出一种共享正、负母线和中线的并联方案来抑制I类零序环流,及一种基于改进型LCL滤波器的并联方案来抑制II、III类零序环流的高频分量,和采用零序环流控制器来抑制II、III类零序环流的低频分量。最后,通过10 kW的三相三电平模块化光伏并网系统的仿真和实验,证明了零序环流模型分析和抑制方法的正确性。

Barotropic current fluctuations coupled with sea level drawdown in Yellow and Bohai Seas

Sub-tidal barotropic current variations coupled with residual sea level fluctuation in the Bohai and Yellow Seas during wintertime are addressed in this study.The temporal evolution and spatial distribution of current fluctuation are investigated using moored acoustic Doppler current profiler data in a three-dimensional numerical model.It is found that a southward current followed by a northward current occurred in the northern Yellow Sea during the fluctuation,concurrent with a significant outflow followed by inflow through the Bohai Strait.The process is consistent from surface to bottom and is coupled with remarkable residual sea level fluctuation.This quasi three-day fluctuation with amplitude 0.2-0.3 m/s leads to 1 m/1.2 m drawdown in the northern Yellow and Bohai Seas,respectively,strongly influencing water exchange between those seas.Because this a prominent feature in the seas,it is necessary to evaluate its effect on fluctuation during winter in future studies,in particular,the northward current during the recovery phase of sea level in the Bohai and Yellow Seas regarding seasonal variation.

Calculation of Eddy Current Loss and Short-circuit Force in SSZ11-50000/110 Power Transformer

The ?method is used in this paper to calculate the leakage magnetic field of SSZ11-50000/110 Power transformer, and by which the structures’ influences to the main leakage flux are analyzed. Through the combination of the product and TEAM Problem 21B, the surface impedance method shows its great advantage in the calculation of eddy current loss.

Suggestions on the Current Electricity Price Level and Policies in China

The State Council decided to raise the retail electricity price by 0.25 Yuan/kWh from July, 2008. This will, to some extent, relieve the conflicts between power supply and demand, and decrease the economic losses in

Fault diagnosis method of AC motor rolling bearing based on heterogeneous data fusion of current and infrared image

In order to improve the accuracy of rolling bearing fault diagnosis when the motor is running under non-stationary conditions,an AC motor rolling bearing fault diagnosis method was proposed based on heterogeneous data fusion of current and infrared images.Firstly,VMD was used to decompose the motor current signal and extract the low-frequency component of the bearing fault signal.On this basis,the current signal was transformed into a two-dimensional graph suitable for convolutional neural network,and the data set was classified by convolutional neural network and softmax classifier.Secondly,the infrared image was segmented and the fault features were extracted,so as to calculate the similarity with the infrared image of the fault bearing in the library,and further the sigmod classifier was used to classify the data.Finally,a decision-level fusion method was introduced to fuse the current signal with the infrared image signal diagnosis result according to the weight,and the motor bearing fault diagnosis result was obtained.Through experimental verification,the proposed fault diagnosis method could be used for the fault diagnosis of motor bearing outer ring under the condition of load variation,and the accuracy of fault diagnosis can reach 98.85%.

基于矢量分类的NPC型三电平双三相PMSM的改进模型预测电压控制

多电平多相电机驱动系统存在电压矢量数目多、冗余复杂及多目标非线性约束等问题。以二极管钳位型三电平六相逆变器驱动双三相永磁同步电机为研究对象,以电机谐波电流抑制和逆变器直流侧中点电位平衡控制为目标,提出一种基于电压矢量三角区域分类的改进模型预测电压控制策略。首先,以基波子平面大投影幅值为原则,对729个电压矢量进行初筛;接着,基于三角区域分类方法对筛选后的电压矢量进行分类,并对期望电压进行所属三角区域定位、确定候选矢量。设计满足电机定子电流谐波抑制及逆变器中点电位平衡控制的目标函数;根据电机数学模型和逆变器特征研究多目标控制权重因子的理论设计方法。不同工况下的有效性及对比实验表明,所研究的控制策略不仅能改善多电平多相电机驱动系统的多目标控制性能,还能有效降低控制器计算负担。

A NEW SOFT-SWITCHING PUSH-PULL THREE-LEVEL CONVERTER

The application areas of conventional push pull converters are limited because of high voltage stress of switches (twice of input voltage). This paper presents a novel zero voltage and zero current switching (ZCS) PWM push pull three level converter in which the voltage stress of switches is input voltage. With phase shifted modulation strategy, the leading switches can only realize zero voltage switching (ZVS), and the lagging switches can realize ZCS when block capacitor and block diodes are added. Using the strategy, the converter overcomes the drawbacks presented by the conventional push pull converter, such as magnetic aberration, large switch loss, and voltage spike on switches, so it can get higher efficiency, and a wider application area. The operating principle of the new converter is analyzed and verified on a 600 W, 50 kHz experimental prototype. Several zero voltage and zero current switching PWM push pull three level converters are proposed.

千安级宽频交流大电流校准系统研究

介绍了一种千安级宽频交流大电流的校准系统,可解决电流范围最大到2 kA、频率从50 Hz~1 kHz的交流大电流的校准问题。为了保证交流大电流溯源链的完整性,开展了补偿式交流电流比率校准方法研究,研制了一套可以覆盖比率到1000∶1、频率到1 kHz的交流电流比率校准系统,解决了关键的非工频电流比率标准溯源问题,并进行了相关测试,以验证交流电流比自校准系统的量传可靠性。通过该校准系统可对被测交流大电流源开展校准试验,验证结果表明系统的扩展不确定度约为2.4×10^(-4),满足大部分宽频交流大电流校准需求。

Dependence of R-G Currenton Bulk Traps Characteristics and Silicon Film Structure in SOI Gated-Diode

The dependence of the Recombination- Generation( R- G) current on the bulk trap characteristics and sili- con film structure in SOI lateral p+ p- n+ diode has been analyzed num erically by using the simulation tool,DESSIS- ISE.By varying the bulk trap characteristics such as the trap density and energy level spectrum systematically,the dependence of the R- G current on both of them has been dem onstrated in details.Moreover,the silicon film doping concentration and thickness are changed to make silicon body varies from the fully- depletion m ode into the partial- ly- depletion one.The influence of the transfer of silicon body characteristics on the R- G currenthas also been care- fully examined.A better understanding is obtained of the behavior of bulk trap R- G current in the SOI lateral gat- ed- diode.

特高压混合级联直流多级自适应协调交流故障穿越控制策略

特高压混合级联直流可以结合电网换相换流器(line commutated converter, LCC)和电压源换流器(voltage source converter, VSC)各自的优势,但也带来了直流侧功率盈余的问题,在受端发生交流故障时,可能导致VSC子模块过压。针对混合级联直流的拓扑特点,文中提出一种基于运行方式和电气量的多级自适应协调控制策略。通过故障阀组负序电压控制、健全阀组辅助电压控制、投入可控自恢复消能装置及送端配合移相、调整送受端换流器直流功率等措施,在站内单VSC内、站内多VSC间、站间LCC与VSC间进行多级自适应协调配合,有效解决了VSC子模块过压问题,实现了混合级联直流的交流故障穿越。基于实际控制保护装置和工程拓扑搭建闭环实时数字仿真试验平台,验证了所提策略的可行性。该策略已成功应用于白鹤滩—江苏特高压混合直流工程。

适应高比例光伏接入的有源配电网自适应电流差动保护

光伏电源大量接入配电网使得配电网线路差动保护的差动电流与制动电流发生变化,传统比率制动式差动保护存在不正确动作风险。为此,在系统分析光伏所接线路两侧基频电流幅值与相角变化特性的基础上,说明光伏电源接入后传统电流差动保护存在的问题;通过推导差动保护临界动作曲线上比率制动系数与两侧电流相角之间的数学关系,提出了一种自适应调整比率制动系数的电流差动保护改进判据;基于PSCAD/EMTDC搭建了含光伏电站的配电网仿真模型,对所提保护改进策略进行了测试,验证了光伏电站高比例接入后所提保护改进策略的有效性和可靠性。

EFFECT OF FUTURE SEA LEVEL RISE ON DISASTROUS FLOODS IN THE TAIHU LAKE LOWER REACH DEPRESSIONS AND COUNTERMEASURES

Use of numerical simulation of the tidal flow of the Changjiang River Estuary and the HuangpuRiver to forecast flood in the Taihu Lake lower reach drainage system for the case of future sea level riseof 0.4 m and 0.8 m,and floods preventing and reducing methods are discussed in this paper.

Characteristics and possible causes of sea level anomalies in the Xisha sea area

Based on the analysis of wind,ocean currents,sea surface temperature（SST） and remote sensing satellite altimeter data,the characteristics and possible causes of sea level anomalies in the Xisha sea area are investigated.The main results are shown as follows：（1） Since 1993,the sea level in the Xisha sea area was obviously higher than normal in 1998,2001,2008,2010 and 2013.Especially,the sea level in 1998 and 2010 was abnormally high,and the sea level in 2010 was 13.2 cm higher than the muti-year mean,which was the highest in the history.In 2010,the sea level in the Xisha sea area had risen 43 cm from June to August,with the strength twice the annual variation range.（2） The sea level in the Xisha sea area was not only affected by the tidal force of the celestial bodies,but also closely related to the quasi 2 a periodic oscillation of tropical western Pacific monsoon and ENSO events.（3）There was a significant negative correlation between sea level in the Xisha sea area and ENSO events.The high sea level anomaly all happened during the developing phase of La Ni-a.They also show significant negative correlations with Ni-o 4 and Ni-o 3.4 indices,and the lag correlation coefficients for 2 months and 3 months are–0.46 and –0.45,respectively.（4） During the early La Ni-a event form June to November in 2010,the anomalous wind field was cyclonic.A strong clockwise vortex was formed for the current in 25 m layer in the Xisha sea area,and the velocity of the current is close to the speed of the Kuroshio near the Luzon Strait.In normal years,there is a “cool eddy”.While in 2010,from July to August,the SST in the area was 2–3°C higher than that of the same period in the history.

Localized deep levels in Al_xGa_(1-x)N epitaxial films with various Al compositions

By using high-temperature deep-level transient spectroscopy （HT-DLTS） and other electrical measurement techniques, localized deep levels in n-type AlxGal xN epitaxial films with various A1 compositions （x = 0, 0.14, 0.24, 0.33, and 0.43） have been investigated. It is found that there are three distinct deep levels in AlxGal-xN films, whose level position with respect to the conduction band increases as AI composition increases. The dominant defect level with the activation energy deeper than 1.0 eV below the conduction band closely follows the Fermi level stabilization energy, indicating that its origin may be related to the defect complex, including the anti-site defects and divacancies in AlxGa1-xN films.

Placement optimization of Multi-Type fault current limiters based on genetic algorithm

The fault current limiter(FCL)is an effective measure for improving system stability and suppressing short-circuit fault current.Because of space and economic costs,the optimum placement of FCLs is vital in industrial applications.In this study,two objectives with the same dimensional measurement unit,namely,the total capital investment cost of FCLs and circuit breaker loss related to short-circuit currents,are considered.The circuit breaker loss model is developed based on the attenuation rule of the circuit breaker service life.The circuit breaker loss is used to quantify the current-limiting effect to avoid the problem of weight selection in a multi-objective problem.The IEEE 10-generator 39-bus system in New England is used to evaluate the performance of the proposed genetic algorithm(GA)method.Comparative and sensitivity analyses are performed.The results of the optimized plan are validated through simulations,indicating the significant potential of the GA for such optimization.

Circle Points Discharge Tube Current Controller

Circle points discharge tube current controller is a new type device to limit the output of high voltage discharge current. Circle points uniform corona discharge to form air ionization current in the discharge tube. On the outside, even if the discharge electrode is spark discharging or the two discharge electrodes are short circuited, the air ionization current in the tube remains within a stable range, and there is no spark discharge. In this case, when the discharge current only increases slightly, the requirement to limited current is obtained. By installing the controller at a discharge pole with a small power but high voltage supply, we can realize the shift between the continuous spark line discharge and corona discharge. This provides a new simple device for spark discharge research and is a supplement to the Townsend discharge experiment.

A Study of Current Land Use in the Urban Area of Ma'anshan City

With the acceleration of urbanization,urban development poses a growing demand for land.China's national conditions of a large population with relatively little arable land require us to intensively use land,and more and more departments have been aware of the importance of intensive urban land use.The study on the current land use in the urban area of Ma'anshan City,is not only conducive to adjustment of land use layout and structure as well as urban ecological construction,but also of guiding significance to the economical and intensive land use in Ma'anshan City.This paper first describes the natural,social and economic situation of Ma'anshan's urban area,then analyzes the land use structure,layout and problems,and finally puts forth the recommendations for improving current land use situation in the urban area of Ma'anshan City.

Research on Numerical Simulation of 3D Leakage Magnetic Field and Short-circuit Impedance of Axial Dual-low-voltage Split-winding Transformer

It is difficult to accurately calculate the short-circuit impedance, due to the complexity of axial dual-low-voltage split-winding transformer winding structure. In this paper, firstly, the leakage magnetic field and short-circuit impedance model of axial dual-low-voltage split-winding transformer is established, and then the 2D and 3D leakage magnetic field are analyzed. Secondly, the short-circuit impedance and split parallel branch current distribution in different working conditions are calculated, which is based on field-circuit coupled method. At last, effectiveness and feasibility of the proposed model is verified by comparison between experiment, analysis and simulation. The results showed that the 3D analysis method is a better approach to calculate the short-circuit impedance, since its analytical value is more closer to the experimental value compared with the 2D analysis results, the finite element method calculation error is less than 2%, while the leakage flux method maximum error is 7.2%.