Pouring position as the input heat source has great infl uence on the temperature fi eld evolution. In this study, the Flow3 D simulation software was applied to investigate the infl uence of pouring methods(with fi x...Pouring position as the input heat source has great infl uence on the temperature fi eld evolution. In this study, the Flow3 D simulation software was applied to investigate the infl uence of pouring methods(with fi xed or moving pouring channel) on AZ91 Mg alloy horizontal centrifugal casting(HCC) process. The simulation results show that the moving pouring channel method can effectively increase the cooling rate and formability of casting pipe. The casting experiment shows that an AZ91 Mg alloy casting pipe with homogeneous microstructure and clear contour was obtained by the moving pouring channel method, and the grain size of the casting pipe is signifi cantly decreased. Meanwhile, serious macro-segregation appeared in the AZ91 casting pipe by the fi xed pouring channel HCC process. Compared with the fi xed pouring channel, the moving pouring channel can remarkably improve the ultimate tensile strength and elongation of the AZ91 HCC pipe from 142.2 MPa to 201.5 MPa and 6.2% to 6.7%, respectively.展开更多
The influence and signification of casting parameters on the solidification process of steel ingot were discussed based on the finite element method (FEM) results by orthogonal experiment method. The range analysis, a...The influence and signification of casting parameters on the solidification process of steel ingot were discussed based on the finite element method (FEM) results by orthogonal experiment method. The range analysis, analysis of variance (ANOVA) and optimization project were used to investigate the FEM results. In order to decrease the ingot riser head and improve the utilization ratio of ingot, the casting parameters involved casting temperature, pouring velocity and interface heat transfer were optimized to decrease shrinkage pore and microporosity. The results show that the heat transfer coefficient between melt and heated board is a more sensitive factor. It is favor to decrease the shrinkage pore and microporosity under the conditions of low temperature, high pouring velocity and high heat transfer between melt and mold. If heat transfer in the ingot body is quicker than that in the riser, the position of shrinkage pore and microporosity will be closer to riser top. The results of optimization project show that few of shrinkage pore and microporosity reach into ingot body with the rational parameters, so the riser size can be reduced.展开更多
基金financially supported by the National Natural Foundation of China(Grant No.51605307)Liaoning Provincial Natural Science Foundation(Grant No.201501084)
文摘Pouring position as the input heat source has great infl uence on the temperature fi eld evolution. In this study, the Flow3 D simulation software was applied to investigate the infl uence of pouring methods(with fi xed or moving pouring channel) on AZ91 Mg alloy horizontal centrifugal casting(HCC) process. The simulation results show that the moving pouring channel method can effectively increase the cooling rate and formability of casting pipe. The casting experiment shows that an AZ91 Mg alloy casting pipe with homogeneous microstructure and clear contour was obtained by the moving pouring channel method, and the grain size of the casting pipe is signifi cantly decreased. Meanwhile, serious macro-segregation appeared in the AZ91 casting pipe by the fi xed pouring channel HCC process. Compared with the fi xed pouring channel, the moving pouring channel can remarkably improve the ultimate tensile strength and elongation of the AZ91 HCC pipe from 142.2 MPa to 201.5 MPa and 6.2% to 6.7%, respectively.
基金Projects(50435010 50705080 50675187) supported by the National Natural Science Foundation of China
文摘The influence and signification of casting parameters on the solidification process of steel ingot were discussed based on the finite element method (FEM) results by orthogonal experiment method. The range analysis, analysis of variance (ANOVA) and optimization project were used to investigate the FEM results. In order to decrease the ingot riser head and improve the utilization ratio of ingot, the casting parameters involved casting temperature, pouring velocity and interface heat transfer were optimized to decrease shrinkage pore and microporosity. The results show that the heat transfer coefficient between melt and heated board is a more sensitive factor. It is favor to decrease the shrinkage pore and microporosity under the conditions of low temperature, high pouring velocity and high heat transfer between melt and mold. If heat transfer in the ingot body is quicker than that in the riser, the position of shrinkage pore and microporosity will be closer to riser top. The results of optimization project show that few of shrinkage pore and microporosity reach into ingot body with the rational parameters, so the riser size can be reduced.
